MIBs Depot

CISCO-ATM-SWITCH-FR-RM-MIB

Registered at
1.3.6.1.4.1.9.9.110
Last updated
1998-07-20 00:00
Organization
Cisco Systems
Namespace
cisco
Source file
CISCO-ATM-SWITCH-FR-RM-MIB
Digest
sha256:8da1cde8a730e370d49ba19c97251ff86a24bbce4a26fede0ff793ebc78a3dcb

Description

This MIB module describes a set of objects used for switch Resource Management (RM) for Frame Relay/Frame based User-to-Network (FUNI) to ATM interworking function (IWF) connections. Please refer to the Frame Relay Forum documents FRF.5 and FRF.8 for details on the Frame Relay to ATM Interworking Functions. For details on FUNI, please refer to the ATM Forum FUNI Specification document. These objects are applicable to Frame Relay and FUNI interfaces present on the Frame Relay Port Adapter Module (PAM). Initial version of this MIB module.

Contact

Cisco Systems Customer Service Postal: 170 West Tasman Drive San Jose CA 95134 USA Phone: +1 800 553-NETS Email: cs-atm@cisco.com

Imports

FromSymbols
CISCO-SMIciscoMgmt
IF-MIBifIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIGauge32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CISCO-ATM-SWITCH-FR-RM-MIB
CISCO-SMI
IANAifType-MIB
IF-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
CfaInterworkServiceCategory
TEXTUAL-CONVENTION
This data type is used to specify the service category of a Frame Relay/FUNI to ATM interworking connection. For definitions of service categories, please refer to the ATM Forum Traffic Management Specification. The current implementation supports the following service categories for connections performing the Frame Relay to ATM Interworking Function: Variable bit rate, non real time (VBR-NRT) Available bit rate (ABR) Unspecified bit rate (UBR)
current

Objects

NameOIDSyntaxAccessStatus
ciscoAtmSwitchFrRmMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.1
cfaAdapter
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.1.1
cfaAdapterIfVcQThresholdTable
OBJECT-TYPE
A table of per-VC queue threshold parameters that are used for congestion control for Frame Relay/FUNI to ATM Interworking Function connections, on the Frame Relay Port Adapter Module. These objects become available as each Frame Relay and FUNI interface is defined on the device. The corresponding ifTypes are frameRelayService(44) and atmFuni(106) respectively. An unique set of threshold parameters are available for every supported Interworking Function service category, and would be applied to all connections belonging to that particular service category, on that Frame Relay or FUNI interface.
1.3.6.1.4.1.9.9.110.1.1.1not-accessiblecurrent
cfaAdapterIfVcQThresholdEntry
OBJECT-TYPE
A set of per-VC queue threshold parameters that are used for congestion control for Frame Relay/FUNI to ATM Interworking Function connections, on the Frame Relay Port Adapter Module. The ifIndex in the index clause refers to MIB-II's ifIndex corresponding to frame-based ATM PAM ports, i.e., Frame Relay and FUNI.
1.3.6.1.4.1.9.9.110.1.1.1.1not-accessiblecurrent
cfaAdapterIfVcQService
OBJECT-TYPE
The service category of the connection to which this entry applies.
1.3.6.1.4.1.9.9.110.1.1.1.1.1CfaInterworkServiceCategorynot-accessiblecurrent
cfaAdapterIfVcQInqDiscThresh
OBJECT-TYPE
This object defines the Discard Eligible threshold applied to the Frame Relay - ATM interworking virtual circuit input queue, on the Frame Relay PAM. The input queue is in the direction of Frame Relay/FUNI interface to the ATM switch fabric. If the fill level of the input queue for the Frame Relay - ATM interworking virtual circuit exceeds this threshold, all frames arriving on this virtual circuit from the Frame Relay side will be discarded at the interface if the arriving frame has its Discard Eligible bit set. The threshold value is expressed as a percent-of-full. Setting this object to 100 effectively turns off the threshold.
1.3.6.1.4.1.9.9.110.1.1.1.1.2INTEGER (1..100)read-writecurrent
cfaAdapterIfVcQOutqDiscThresh
OBJECT-TYPE
This object defines the Discard Eligible threshold applied to the Frame Relay - ATM interworking virtual circuit output queue, on the Frame Relay PAM. The output queue is in the direction of the ATM switch fabric to the Frame Relay/FUNI interface. If the fill level of the output queue for the Frame Relay - ATM interworking virtual circuit exceeds this threshold, all frames arriving on this virtual circuit from the ATM switch fabric side will be discarded if the arriving frame has its Discard Eligible bit set. The threshold value is expressed as a percent-of-full. Setting this object to 100 effectively turns off the threshold.
1.3.6.1.4.1.9.9.110.1.1.1.1.3INTEGER (1..100)read-writecurrent
cfaAdapterIfVcQInqMarkThresh
OBJECT-TYPE
This object defines the Marking threshold applied to the Frame Relay - ATM interworking virtual circuit input queue, on the Frame Relay PAM. The input queue is in the direction of Frame Relay/FUNI interface to the ATM switch fabric. If the fill level of the input queue for the Frame Relay - ATM interworking virtual circuit exceeds this threshold, the following will happen: 1. For frames coming into the Frame Relay - ATM interworking virtual circuit from the Frame Relay side, the corresponding cells will have the Explicit Forward Congestion Indication (EFCI) bit set in the ATM cell header, on entry into the ATM switch fabric. 2. For cells arriving from the ATM switch fabric side for this Frame Relay - ATM interworking virtual circuit, the corresponding frames will have the Backward Explicit Congestion Notification (BECN) bit set upon exiting the Frame Relay interface. The threshold value is expressed as a percent-of-full. Setting this object to 100 effectively turns off the threshold.
1.3.6.1.4.1.9.9.110.1.1.1.1.4INTEGER (1..100)read-writecurrent
cfaAdapterIfVcQOutqMarkThresh
OBJECT-TYPE
This object defines the Marking threshold applied to the Frame Relay - ATM interworking virtual circuit output queue, on the Frame Relay PAM. The output queue is in the direction of the ATM switch fabric to the Frame Relay/FUNI interface. If the fill level of the output queue for the Frame Relay - ATM interworking virtual circuit exceeds this threshold, the following will happen: 1. For frames coming into the Frame Relay - ATM interworking virtual circuit from the Frame Relay side, the frame will have the BECN bit set in the Frame Relay header before getting converted to cells and entering the ATM switch fabric. 2. For cells arriving from the ATM switch fabric side for this Frame Relay - ATM interworking virtual circuit, the corresponding frames will have the Forward Explicit Congestion Notification (FECN) bit set in the Frame Relay header upon exiting the Frame Relay interface. For FUNI - ATM interworking connections, the Congestion Notification (CN) bit gets set in the FUNI header. The threshold value is expressed as a percent-of-full. Setting this object to 100 effectively turns off the threshold.
1.3.6.1.4.1.9.9.110.1.1.1.1.5INTEGER (1..100)read-writecurrent
cfaAdapterIfVbrServOflowTable
OBJECT-TYPE
A table of Resource Management parameters that are used for VBR Overflow Servicing for Frame Relay/FUNI to ATM Interworking Function connections, on the Frame Relay Port Adapter Module. This object becomes available as each Frame Relay and FUNI interface is defined on the device. The corresponding ifTypes are frameRelayService(44) and atmFuni(106) respectively.
1.3.6.1.4.1.9.9.110.1.1.2not-accessiblecurrent
cfaAdapterIfVbrServOflowEntry
OBJECT-TYPE
A set of Resource Management parameters that are used for VBR Overflow Servicing for Frame Relay/FUNI to ATM Interworking Function connections, on the Frame Relay Port Adapter Module.
1.3.6.1.4.1.9.9.110.1.1.2.1not-accessiblecurrent
cfaAdapterIfVbrServOflow
OBJECT-TYPE
Configuration to enable the overflow feature for VBR-NRT connections on the interface. When the PAM services VBR-NRT VC input queues, sending ATM traffic to the switch fabric, it can strictly limit the rate at which the data is sent to contracted sustained cell rate (SCR) for the connection (overflow disabled), or allow data transfer over SCR (overflow enabled). Setting the value to true enables overflow.
1.3.6.1.4.1.9.9.110.1.1.2.1.1TruthValueread-writecurrent
cfaAdapterIfFrConfigTable
OBJECT-TYPE
A table of resource management parameters for the Frame Relay interface on the FR/FUNI Port Adapter Module.
1.3.6.1.4.1.9.9.110.1.1.3not-accessiblecurrent
cfaAdapterIfFrConfigEntry
OBJECT-TYPE
An entry in the table, containing information about Resource Management of an Interface with Frame Relay encapsulation.
1.3.6.1.4.1.9.9.110.1.1.3.1not-accessiblecurrent
cfaAdapterIfOverbooking
OBJECT-TYPE
This object defines overbooking of CIR on an acess link/port in percent of access rate. The total of all CIR's for all frame-relay pvc's and frame-relay soft-vc's cannot exceed CIR overbooking factor times access rate. For example, overbooking of 200% means the total of all CIR's can be configured up to twice of the access rate. The default is 100% - no overbooking is set.
1.3.6.1.4.1.9.9.110.1.1.3.1.1INTEGER (100..1000)read-writecurrent
cfaInterwork
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.1.2
cfaInterworkIfResourceTable
OBJECT-TYPE
A table of objects that can be used to view available and allocated resources on Frame Relay and FUNI interfaces defined on a Frame Relay Port Adapter Module (PAM). An unique set of available and allocated resources are available for the transmit direction (going out of the interface to the external world), and receive direction (coming into the interface from the external world). These available and allocated resources are available for every supported Interworking Function service category. These objects become available as each Frame Relay and FUNI interface is defined on the device. The corresponding ifTypes are frameRelayService(44) and atmFuni(106) respectively.
1.3.6.1.4.1.9.9.110.1.2.1not-accessiblecurrent
cfaInterworkIfResourceEntry
OBJECT-TYPE
A set of objects that can be used to view available and allocated resources on Frame Relay and FUNI interfaces defined on a Frame Relay Port Adapter Module (PAM).
1.3.6.1.4.1.9.9.110.1.2.1.1not-accessiblecurrent
cfaInterworkIfVcQService
OBJECT-TYPE
The service category of the connection to which this entry applies.
1.3.6.1.4.1.9.9.110.1.2.1.1.1CfaInterworkServiceCategorynot-accessiblecurrent
cfaInterworkIfRxAvailRate
OBJECT-TYPE
The available bit rate for traffic received on the Frame Relay interface. This is the bandwidth available for connections. This value decreases as a result of setup of a connection requesting non-zero Committed Information Rate (CIR) in the receive direction, and increases as a result of the release of such a connection.
1.3.6.1.4.1.9.9.110.1.2.1.1.2Gauge32read-onlycurrent
cfaInterworkIfTxAvailRate
OBJECT-TYPE
The available bit rate for traffic sent out the Frame Relay interface. This is the bandwidth available for connections. This value decreases as a result of setup of a connection requesting non-zero CIR in the transmit direction, and increases as a result of the release of such a connection.
1.3.6.1.4.1.9.9.110.1.2.1.1.3Gauge32read-onlycurrent
cfaInterworkIfRxAllocRate
OBJECT-TYPE
The allocated bit rate for traffic received on the Frame Relay interface. This is the bandwidth allocated to connections. This value increases as a result of setup of a connection requesting non-zero CIR in the receive direction, and decreases as a result of the release of such a connection.
1.3.6.1.4.1.9.9.110.1.2.1.1.4Gauge32read-onlycurrent
cfaInterworkIfTxAllocRate
OBJECT-TYPE
The allocated bit rate for traffic sent out the Frame Relay interface. This is the bandwidth allocated to connections. This value increases as a result of setup of a connection requesting non-zero CIR in the transmit direction, and decreases as a result of the release of such a connection.
1.3.6.1.4.1.9.9.110.1.2.1.1.5Gauge32read-onlycurrent
ciscoAtmSwitchFrRmMIBNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.2
ciscoAtmSwitchFrRmMIBConformance
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.3
ciscoAtmSwitchFrRmMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.3.1
ciscoAtmSwitchFrRmMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.110.3.2

Conformance

NameOIDStatus
ciscoAtmSwitchFrRmMIBCompliance
MODULE-COMPLIANCE
The compliance statement for the Cisco Frame Relay/FUNI to ATM Interworking Function Resource Management MIB.
1.3.6.1.4.1.9.9.110.3.1.1current
cfaAdapterGroup
OBJECT-GROUP
A collection of objects which manage resources for Cisco Frame Relay/FUNI to ATM Interworking Function connections.
1.3.6.1.4.1.9.9.110.3.2.1current
cfaInterworkGroup
OBJECT-GROUP
A collection of objects which manage resources for Cisco Frame Relay/FUNI to ATM Interworking Function connections.
1.3.6.1.4.1.9.9.110.3.2.2current