CISCO-ACL-MIB
- Registered at
- 1.3.6.1.4.1.9.9.808
- Last updated
- 2013-03-27 00:00
- Organization
- Cisco Systems, Inc.
- Revisions
- 2013-03-27 00:00
- Namespace
- cisco
- Source file
CISCO-ACL-MIB- Digest
sha256:28f9a2f617bdd73f7925ff03d9d93246bd83e0d8b4843c752dba1aecc3bf5872
Description
This MIB module defines objects that describe Cisco Access Control Lists (ACL). This MIB describes different objects that enable the network administrator to remotely configure ACLs, apply them to interfaces and monitor their usage statistics. A typical application of this MIB module will facilitate monitoring of ACL match (sometimes referred as hit) counts. However, by no means does the definition of this MIB module prevent other applications from using it. An ACL is an ordered list of statements that deny or permit packets based on matching fields contained within the packet header (layer 3 source and destination addresses, layer 4 protocol, layer 4 source and destination port numbers, etc.) In addition there is an implicit *Deny All* at the end of the ACL. ACLs are used to perform packet filtering to control which packets are allowed through the network. Such control can help limit network traffic, and restrict the access of applications and devices on the network. Each one of these statements is referred to as an Access List Control Entry (ACE). Here is an example of an ACL configuration. ipv4 access-list V4Example 10 permit tcp any any ! ipv6 access-list V6Example 10 permit tcp any any ! The mechanism for monitoring ACL usage is by configuring, in the desired ACEs a counter label. A counter label is a name that is given to a counter and is defined in any ACE. ACEs that share the same Counter label name will have their counters aggregated into the same label. Here is an example of how to use counter labels. ipv4 access-list V4CounterExample 10 permit tcp any any counter CountPermits 20 permit udp any any counter CountPermits The same applies to IPv6 ACLs. This MIB consists of following tables: * caAclCfgTable Defines the ACLs configured in the device. * caAclIPV4ACECfgTable Defines the ACEs that make up an IPV4 ACL. * caAclIPV6ACECfgTable Defines the ACEs that make up an IPV6 ACL. * caAclAccessGroupCfgTable Defines the Access Control Groups (ACG) applied to interfaces on the device. * caAclLabelIntfStatsTable Defines the statistics for a specific ACE with counter labels attached to interfaces on the device.
Contact
Cisco Systems Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | CiscoIpProtocol |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressType, InetPortNumber |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter64, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-ACL-MIB CISCO-SMI CISCO-TC IANAifType-MIB IF-MIB INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| CaAclACLIndex TEXTUAL-CONVENTION A unique value, greater than zero, for each ACL name in the managed system. It is recommended that these values be assigned contiguously starting from 1. The value for each ACL name must remains constant at least from one re-initialization of the entity's network management system to the next re-initialization. | current | |||
| CaAclAction TEXTUAL-CONVENTION Enumeration value indicating the action to be taken on packets that match the ACE. permit(1) the packet will be considered for further processing. deny(2) the packet will be dropped without any further processing. | current | |||
| CaAclLogOption TEXTUAL-CONVENTION Enumeration value indicating the log option that is to be applied to an ACE. Currently the options are log-input and log. The difference between log and logInput is that logInput logs all the information as in log, with the addition of ingress interface as well as the MAC address of the device that last handled the packet. | current | |||
| CaAclPortOperator TEXTUAL-CONVENTION This textual convention represents the operator that will be applied on the transport layer source/destination ports. The port in packets to be filtered and the port (or port range in case of range(5)). lt(1) - match ports that are small than the configured value. gt(2) - match ports that are greater than the configured value. eq(3) - match ports that are equal to the configured value. neq(4) - match ports that are not equal to the configured value. range(5) - match ports in the range of configured values, inclusive. | current | |||
| CaAclPrecedenceValue TEXTUAL-CONVENTION An enumeration value indicating the value of the precedence field. It is specified as a number between 0 and 7, as defined in RFC-791. | current | |||
| CaAclSequenceNumber TEXTUAL-CONVENTION A unsigned 32-bit integer value. | current | |||
| CaAclTcpFlagsMatch TEXTUAL-CONVENTION An enumeration value indicating the type of matching that is to be done on the TCP flags field of the packet, providing that the packet being filtered is a TCP packet. matchAny(1) - take caAclAction if any of TCP flags in the packet match the configured value. matchAll(2) - take caAclAction only if all the TCP flags in packet match the configured value. matchNone(3) - take caAclAction only if none of the TCP flags in the packet match the configure value. | current | |||
| CaAclTrafficDirection TEXTUAL-CONVENTION Enumeration value indicating the direction of the ACL ingress - in the ingress (input) direction, egress - in the egress (output) direction. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| caAclMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.1 | |||
| caAclConfiguration OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.1.1 | |||
| caAclCfgTable OBJECT-TYPE A table of ACL definitions. Each entry in this table defines a unique IPV4 or IPV6 ACL. | 1.3.6.1.4.1.9.9.808.1.1.1 | not-accessible | current | |
| caAclCfgTableEntry OBJECT-TYPE A conceptual row in the caAclTable. Each entry of this table consists of acl index and the address type. This is so that the table may contain both IPV4 and IPV6 ACLs. | 1.3.6.1.4.1.9.9.808.1.1.1.1 | not-accessible | current | |
| caAclIndex OBJECT-TYPE An arbitrary (system assigned) index for each ACL name. The index is unique for each ACL name in the device, but is further qualified by the address family. For example, consider the following configuration: ipv4 access-list ACL1 10 permit ipv4 any any ! ipv6 access-list ACL1 10 permit ipv6 any any In this case the caAclIndex value for both ACLs will be the same. | 1.3.6.1.4.1.9.9.808.1.1.1.1.1 | CaAclACLIndex | not-accessible | current |
| caAclAddressType OBJECT-TYPE This object defines the address family of the ACL. | 1.3.6.1.4.1.9.9.808.1.1.1.1.2 | InetAddressType | not-accessible | current |
| caAclName OBJECT-TYPE A string that identifies the ACL name. | 1.3.6.1.4.1.9.9.808.1.1.1.1.3 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclRowStatus OBJECT-TYPE This object is used to create, modify, or delete an entry in the caAclTable. A row can be created using the 'CreateAndGo' option. When the row is successfully created, the RowStatus will be set to active by the agent. Once a row becomes active, values in any other column within the row cannot be modified. A row may be deleted by setting the RowStatus for 'destroy'. | 1.3.6.1.4.1.9.9.808.1.1.1.1.4 | RowStatus | read-create | current |
| caAclIPV4ACECfgTable OBJECT-TYPE A table of IPV4 ACE definitions. The ACE definition controls whether packets are accepted or rejected. The access control may be applied before sending the packet to the forwarding engine, or may be applied after the packet is processed by the forwarding engine. If two ACE entries with the same sequence number are configured the latter will overwrite the former. | 1.3.6.1.4.1.9.9.808.1.1.2 | not-accessible | current | |
| caAclIPV4ACECfgTableEntry OBJECT-TYPE A conceptual row in the caAclIPV4ACLTable. Each entry of this table consists of a set of match criteria for a given ACL. | 1.3.6.1.4.1.9.9.808.1.1.2.1 | not-accessible | current | |
| caAclIPV4ACESequenceNumber OBJECT-TYPE This object uniquely identifies an ACE within an ACL. Sequence numbers are assigned to each permit/deny statement, causing the system to insert the statement in that numbered position within the ACL. If two ACE entries with the same sequence number are configured, the latter one will overwrite the former. | 1.3.6.1.4.1.9.9.808.1.1.2.1.1 | CaAclSequenceNumber | not-accessible | current |
| caAclIPV4ACEAction OBJECT-TYPE This object indicates the type of action to be taken if the packet matches the given criteria. If it is set to permit(1), all packets matching this ACE will be allowed for further processing. If it is set to deny(2), all packets matching this ACE will be discarded. | 1.3.6.1.4.1.9.9.808.1.1.2.1.2 | CaAclAction | read-create | current |
| caAclIPV4ACEProtocol OBJECT-TYPE This object identifies the layer 3 protocol type to be filtered by the ACE. Protocol numbers are defined in the Network Working Group Request For Comment documents. | 1.3.6.1.4.1.9.9.808.1.1.2.1.3 | CiscoIpProtocol | read-create | current |
| caAclIPV4ACESourceAddress OBJECT-TYPE This object determines the address of the network or host from which the packet is being sent. If this object value is 0.0.0.0 and the value of caAclIPV4ACESourceWildCardMask object in the same entry is 255.255.255.255, this entry matches any source address. If this object value is not 0.0.0.0 and the value of caAclIPV4ACESourceWildCardMask is 0.0.0.0, this entry matches specific host address defined in this object. | 1.3.6.1.4.1.9.9.808.1.1.2.1.4 | InetAddress | read-create | current |
| caAclIPV4ACESourceWildCardMask OBJECT-TYPE This object determines the mask of wild card address bits for caAclIPV4ACESourceAddress. Wild card masking is to indicate to the system whether to check or ignore the corresponding IP address bits when comparing the address bits in an ACL to a packet being submitted to the ACL. The default wild card mask is 0.0.0.0. The wild card mask is the inverse of a regular subnet mask. If the mask value 0.0.0.255 is applied to 1.2.3.0. | 1.3.6.1.4.1.9.9.808.1.1.2.1.5 | InetAddress | read-create | current |
| caAclIPV4ACESourceNetworkGroup OBJECT-TYPE This object defines the Source Network Object Group from which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.2.1.6 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV4ACESourcePortOperator OBJECT-TYPE This object defines the operation to be performed to the layer source port field. Source port fields are present only for IGMP, ICMP, SCTP, TCP, and UDP protocols. If caAclIPV4ACEProtocol is none of the ones listed above, this field should set to noOperator(1), which means not comparison is to be performed. If this field is set to range(5) then two port numbers are necessary. I.e., Both caAclIPV4ACESourcePort and caAclIPV4ACESourcePortUpper need to be provided. | 1.3.6.1.4.1.9.9.808.1.1.2.1.7 | CaAclPortOperator | read-create | current |
| caAclIPV4ACESourcePort OBJECT-TYPE This object defines the source port number of the layer 4 protocol. This is the field to be matched with the specified source port based on the caAclIPV4ACESourcePortOperator. If caAclIPV4ACESourcePortOperator is range(5) then this object will have the inclusive lower bound of the source port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.2.1.8 | InetPortNumber | read-create | current |
| caAclIPV4ACESourcePortUpper OBJECT-TYPE This object defines the inclusive upper bound of the layer 4 source port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.2.1.9 | InetPortNumber | read-create | current |
| caAclIPV4ACESourcePortGroup OBJECT-TYPE This object defines the Source Port Object Group from which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.2.1.10 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV4ACEDestinationAddress OBJECT-TYPE This object determines the address of the network or host to which the packet is being sent. If this object value is 0.0.0.0 and the value of caAclIPV4ACLDestinationWildCardMask object in the same entry is 255.255.255.255, this entry matches any source IP address. If this object value is not 0.0.0.0 and the value of caAclIPV4ACLDestinationWildCardMask is 0.0.0.0, this entry matches the specific host address defined in this object. | 1.3.6.1.4.1.9.9.808.1.1.2.1.11 | InetAddress | read-create | current |
| caAclIPV4ACEDestinationWildCardMask OBJECT-TYPE This object determines the mask of wild card address bits for caAclIPV4ACLDestinationAddress. Wild card masking is to indicate to the system whether to check or ignore the corresponding IP address bits when comparing the address bits in an ACE to a packet being submitted to the ACE. The default wild card mask is 0.0.0.0. The wild card mask is the inverse of a regular subnet mask. If the mask value 0.0.0.255 is applied to the address 1.2.3.4, it will match all traffic from subnet 1.2.3.0. | 1.3.6.1.4.1.9.9.808.1.1.2.1.12 | InetAddress | read-create | current |
| caAclIPV4ACEDestinationNetworkGroup OBJECT-TYPE This object defines the Destination Network Object Group to which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.2.1.13 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV4ACEDestinationPortOperator OBJECT-TYPE This object defines the operation to be performed to the layer destination port field. Source port fields are present only for IGMP, ICMP, SCTP, TCP, and UDP protocols. If caAclIPV4ACLProtocol is none of the ones listed above, this field should set to noOperator(1), which means not comparison is to be performed. If this field is set to range(5) then two port numbers are necessary. I.e., Both caAclIPV4ACEDestinationPort and caAclIPV4ACEDestinationPortUpper need to be provided. | 1.3.6.1.4.1.9.9.808.1.1.2.1.14 | CaAclPortOperator | read-create | current |
| caAclIPV4ACEDestinationPort OBJECT-TYPE This object defines the destination port number of the layer 4 protocol. This is the field to be matched with the specified destination port based on the caAclIPV4ACLSourceOperator. If caAclIPV4ACLDestinationOperator is range(5) then this object will have the inclusive lower bound of the destination port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.2.1.15 | InetPortNumber | read-create | current |
| caAclIPV4ACEDestinationPortUpper OBJECT-TYPE This object defines the inclusive upper bound of the layer 4 destination port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.2.1.16 | InetPortNumber | read-create | current |
| caAclIPV4ACEDestinationPortGroup OBJECT-TYPE This object defines the Source Port Object Group to which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.2.1.17 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV4ACEDscpValue OBJECT-TYPE This object defines the dscp value that will be considered in the match criteria against the value in the packet. | 1.3.6.1.4.1.9.9.808.1.1.2.1.18 | Unsigned32 (0..63) | read-create | current |
| caAclIPV4ACETcpFlagsValue OBJECT-TYPE This object defines the value of the TCP flags which will be considered in the match criteria based on caAclIPV4ACLTcpFlagsMatchType. Users can select any desired combination of the TCP flags on which to filter TCP packets. | 1.3.6.1.4.1.9.9.808.1.1.2.1.19 | Unsigned32 (0..255) | read-create | current |
| caAclIPV4ACETcpFlagsMask OBJECT-TYPE This object defines the mask value of the TCP flags field. | 1.3.6.1.4.1.9.9.808.1.1.2.1.20 | Unsigned32 (0..255) | read-create | current |
| caAclIPV4ACETcpFlagsMatchType OBJECT-TYPE This object defines the type of matching to be done on the TCP flags field. | 1.3.6.1.4.1.9.9.808.1.1.2.1.21 | CaAclTcpFlagsMatch | read-create | current |
| caAclIPV4ACETosValue OBJECT-TYPE This object defines the value of the TOS field to be filtered. Packets can be filtered by the TOS level as specified by a number from 0 to 15. Use the value 16 to indicate that the TOS field should be ignored during matching. | 1.3.6.1.4.1.9.9.808.1.1.2.1.22 | Unsigned32 (0..16) | read-create | current |
| caAclIPV4ACEPrecedenceValue OBJECT-TYPE This object indicates the value of the precedence field to be filtered. | 1.3.6.1.4.1.9.9.808.1.1.2.1.23 | CaAclPrecedenceValue | read-create | current |
| caAclIPV4ACELogOption OBJECT-TYPE This object defines the value of the log option field to be applied to packets that match this ACE entry. | 1.3.6.1.4.1.9.9.808.1.1.2.1.24 | CaAclLogOption | read-create | current |
| caAclIPV4ACECounterLabel OBJECT-TYPE This object defines the counter label name for this ACE. ACEs that share the same counter label name will have their hit counts aggregated into the same counter label name. | 1.3.6.1.4.1.9.9.808.1.1.2.1.25 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV4ACERemark OBJECT-TYPE This object defines a comment in the ACL. It helps the user to define some meaningful comment to identify the ACE quickly, or to know the purpose of a set of ACEs. This field is not used during packet matching. | 1.3.6.1.4.1.9.9.808.1.1.2.1.26 | SnmpAdminString (SIZE(1..100)) | read-create | current |
| caAclIPV4ACERowStatus OBJECT-TYPE This object is used to create, modify, or delete an entry in the caAclIPV4ACLTable. A row can be created using the 'CreateAndGo' option. When the row is successfully created, the RowStatus will be set to active by the agent. A row may be deleted by setting the RowStatus for 'destroy'. The minimum objects required to delete a row in this table is simply the sequence number (caAclIPV4ACESequenceNumber). | 1.3.6.1.4.1.9.9.808.1.1.2.1.27 | RowStatus | read-create | current |
| caAclIPV6ACECfgTable OBJECT-TYPE A table of IPV6 ACE definitions. The ACE definition controls whether packets are accepted or rejected. The access control may be applied before sending the packet to the forwarding engine, or may be applied after the packet is processed by the forwarding engine. | 1.3.6.1.4.1.9.9.808.1.1.3 | not-accessible | current | |
| caAclIPV6ACECfgTableEntry OBJECT-TYPE A conceptual row in the caAclIPV6ACLTable. Each entry of this table consists of a set of match criteria for a given ACL. | 1.3.6.1.4.1.9.9.808.1.1.3.1 | not-accessible | current | |
| caAclIPV6ACESequenceNumber OBJECT-TYPE This object uniquely identifies an ACE within an ACL. Sequence numbers are assigned to each permit/deny statement, causing the system to insert the statement in that numbered position within the ACL. | 1.3.6.1.4.1.9.9.808.1.1.3.1.1 | CaAclSequenceNumber | not-accessible | current |
| caAclIPV6ACEAction OBJECT-TYPE This object indicates the type of action to be taken if the packet matches the given criteria. If it is set to permit(1), all packets matching this ACE will be allowed for further processing. If it is set to deny(2), all packets matching this ACE will be discarded. | 1.3.6.1.4.1.9.9.808.1.1.3.1.2 | CaAclAction | read-create | current |
| caAclIPV6ACEProtocol OBJECT-TYPE This object identifies the protocol type to be filtered by the ACE. Protocol numbers are defined in the Network Working Group Request For Comment (RFC) documents. | 1.3.6.1.4.1.9.9.808.1.1.3.1.3 | CiscoIpProtocol | read-create | current |
| caAclIPV6ACESourceAddress OBJECT-TYPE This object determines the address of the network or host from which the packet is being sent. If this object value is 0::0 and the value of caAclIPV6ACLSourcePrefixLength is 0 then this matches any source address. If this object value is not 0::0 and the value of caAclIPV6ACLSourcePrefixLength is less than 128, this entry matches the all the addresses that are in the sub-net. If this object value is 0::0 and the value of caAclIPV6ACLSourcePrefixLength is also 0, this entry matches all hosts. | 1.3.6.1.4.1.9.9.808.1.1.3.1.4 | InetAddress | read-create | current |
| caAclIPV6ACESourcePrefixLength OBJECT-TYPE This object determines the number of bits in the field caAclIPV6ACLSourceAddress to be checked. If the value of this object is 0, then the source address in the packet must match caAclIPV6ACESourceAddress exactly for the ACE action to be taken. | 1.3.6.1.4.1.9.9.808.1.1.3.1.5 | Integer32 (0..128) | read-create | current |
| caAclIPV6ACESourceNetworkGroup OBJECT-TYPE This object defines the Source Network Object Group from which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.3.1.6 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV6ACESourcePortOperator OBJECT-TYPE This object defines the operation to be performed to the layer source port field. Source port fields are present only for IGMP, ICMP, SCTP, TCP, and UDP protocols. If caAclIPV6ACLProtocol is none of the ones listed above, this field should set to noOperator(1), which means not comparison is to be performed. If this field is set to range(5) then two port numbers are necessary. I.e., Both caAclIPV6ACLSourcePort and caAclIPV6ACLSourcePortUpper need to be provided. | 1.3.6.1.4.1.9.9.808.1.1.3.1.7 | CaAclPortOperator | read-create | current |
| caAclIPV6ACESourcePort OBJECT-TYPE This object defines the source port number of the layer 4 protocol. This is the field to be matched with the specified source port based on the caAclIPV6ACLSourceOperator. If caAclIPV6ACLSourceOperator is range(5) then this object wail have the inclusive lower bound of the source port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.3.1.8 | InetPortNumber | read-create | current |
| caAclIPV6ACESourcePortUpper OBJECT-TYPE This object defines the inclusive upper bound of the layer 4 source port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.3.1.9 | InetPortNumber | read-create | current |
| caAclIPV6ACESourcePortGroup OBJECT-TYPE This object defines the Source Port Object Group from which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.3.1.10 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV6ACEDestinationAddress OBJECT-TYPE This object determines the address of the network or host to which the packet is being sent. If this object value is 0::0 and the value of caAclIPV6ACLSourcePrefixLength is 0 then this matches any source address. If this object value is not 0::0 and the value of caAclIPV6ACLSourcePrefixLength is less than 128, this entry matches the all the addresses that are in the sub-net. If this object value is 0::0 and the value of caAclIPV6ACLSourcePrefixLength is also 0, this entry matches all osts. | 1.3.6.1.4.1.9.9.808.1.1.3.1.11 | InetAddress | read-create | current |
| caAclIPV6ACEDestinationPrefixLength OBJECT-TYPE This object determines the number of bits in the field caAclIPV6ACLDestinationAddress to be checked. If the value of this object is 0, then the source address in the packet must match caAclIPV6ACEDestinationAddress exactly for the ACE action to be taken. | 1.3.6.1.4.1.9.9.808.1.1.3.1.12 | Integer32 (0..128) | read-create | current |
| caAclIPV6ACEDestinationNetworkGroup OBJECT-TYPE This object defines the Source Network Object Group to which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.3.1.13 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV6ACEDestinationPortOperator OBJECT-TYPE This object defines the operation to be performed to the layer destination port field. Source port fields are present only for IGMP, ICMP, SCTP, TCP, and UDP protocols. If caAclIPV6ACLProtocol is none of the ones listed above, this field should set to noOperator(1), which means no comparison is to be performed. If this field is set to range(5) then two port numbers are necessary. I.e., Both caAclIPV6ACLDestinationPort and caAclIPV6ACLDestinationPortUpper need to be provided. | 1.3.6.1.4.1.9.9.808.1.1.3.1.14 | CaAclPortOperator | read-create | current |
| caAclIPV6ACEDestinationPort OBJECT-TYPE This object defines the destination port number of the layer 4 protocol. This is the field to be matched with the specified destination port based on the caAclIPV6ACLSourceOperator. If caAclIPV6ACLDestinationOperator is range(5) then this object will have the inclusive lower bound of the destination port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.3.1.15 | InetPortNumber | read-create | current |
| caAclIPV6ACEDestinationPortUpper OBJECT-TYPE This object defines the inclusive upper bound of the layer 4 destination port range that is to be matched. | 1.3.6.1.4.1.9.9.808.1.1.3.1.16 | InetPortNumber | read-create | current |
| caAclIPV6ACEDestinationPortGroup OBJECT-TYPE This object defines the Source Port Object Group to which the packet is being sent. | 1.3.6.1.4.1.9.9.808.1.1.3.1.17 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV6ACETrafficClassValue OBJECT-TYPE This object defines the traffic class value that will be considered in the match criteria against the value in the packet. | 1.3.6.1.4.1.9.9.808.1.1.3.1.18 | Unsigned32 (0..255) | read-create | current |
| caAclIPV6ACETcpFlagsValue OBJECT-TYPE This object defines the value of the TCP flags which will be considered in the match criteria based on caAclIPV6ACLTcpFlagsMatchType. Users can select any desired combination of the TCP flags on which to filter TCP packets. | 1.3.6.1.4.1.9.9.808.1.1.3.1.19 | Unsigned32 (0..255) | read-create | current |
| caAclIPV6ACETcpFlagsMask OBJECT-TYPE This object defines the mask value of the TCP flags field. | 1.3.6.1.4.1.9.9.808.1.1.3.1.20 | Unsigned32 (0..255) | read-create | current |
| caAclIPV6ACETcpFlagsMatchType OBJECT-TYPE This object defines the type of matching to be done on the TCP flags field. | 1.3.6.1.4.1.9.9.808.1.1.3.1.21 | CaAclTcpFlagsMatch | read-create | current |
| caAclIPV6ACELogOption OBJECT-TYPE This object defines the value of the log option field to be applied to packets that match this ACE entry. | 1.3.6.1.4.1.9.9.808.1.1.3.1.22 | CaAclLogOption | read-create | current |
| caAclIPV6ACECounterLabel OBJECT-TYPE This object defines the counter label name for this ACE. ACEs that share the same counter label name will have their hit counts aggregated into the same counter label name. | 1.3.6.1.4.1.9.9.808.1.1.3.1.23 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| caAclIPV6ACERemark OBJECT-TYPE This object defines a comment in the ACL. It helps the user to define some meaningful comment to identify the ACE quickly, or to know the purpose of a set of ACEs. This field is not used during packet matching. | 1.3.6.1.4.1.9.9.808.1.1.3.1.24 | SnmpAdminString (SIZE(1..100)) | read-create | current |
| caAclIPV6ACERowStatus OBJECT-TYPE This object is used to create, modify, or delete an entry in the caAclIPV6ACLTable. A row can be created using the 'CreateAndGo' option. When the row is successfully created, the RowStatus will be set to active by the agent. A row may be deleted by setting the RowStatus for 'destroy'. The minimum objects required to delete a row in this table is simply the sequence number (caAclIPV6ACESequenceNumber). | 1.3.6.1.4.1.9.9.808.1.1.3.1.25 | RowStatus | read-create | current |
| caAclAccessGroupCfgTable OBJECT-TYPE This table lists the ACLs configured on the device and applied on an interface in the ingress or egress direction. | 1.3.6.1.4.1.9.9.808.1.1.4 | not-accessible | current | |
| caAclAccessGroupCfgEntry OBJECT-TYPE This entry describes an ACL configured on the device and applied to an interface. | 1.3.6.1.4.1.9.9.808.1.1.4.1 | not-accessible | current | |
| caAclAccessGroupACL OBJECT-TYPE The name of the ACL associated with this entry. | 1.3.6.1.4.1.9.9.808.1.1.4.1.1 | CaAclACLIndex | read-create | current |
| caAclAccessGroupCfgAddressType OBJECT-TYPE This entry describes the address family of the access group being applied on the interface. | 1.3.6.1.4.1.9.9.808.1.1.4.1.2 | InetAddressType | not-accessible | current |
| caAclAccessGroupDirection OBJECT-TYPE This object defines the direction in which the ACL is applied. | 1.3.6.1.4.1.9.9.808.1.1.4.1.3 | CaAclTrafficDirection | not-accessible | current |
| caAclAccessGroupSequenceNumber OBJECT-TYPE This object uniquely identifies the order that Access Group applied to a interface. It can be used by platforms that support applying more than one Access List per address family per direction. For example: interface GigabitEthernet 0/0 ipv4 access-group ACL1 ACL2 ACL2 ingress ! | 1.3.6.1.4.1.9.9.808.1.1.4.1.4 | CaAclSequenceNumber | not-accessible | current |
| caAclAccessGroupRowStatus OBJECT-TYPE This object is used to create, modify, or delete an entry in the caAclAccessGroupCfgTable. A row can be created using the 'CreateAndGo' option. When the row is successfully created, the RowStatus will be set to active by the agent. Once a row becomes active, values in any other column within the row cannot be modified. A row may be deleted by setting the RowStatus for 'destroy'. | 1.3.6.1.4.1.9.9.808.1.1.4.1.5 | RowStatus | read-create | current |
| caAclStats OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.1.2 | |||
| caAclLabelIntfStatsTable OBJECT-TYPE This table describes the statistics for all ACEs with assigned counter labels, attached to interfaces on the device. An entry in this table is created when an ACL containing an ACE that references the specified counter label name is applied to an interface. An entry in this table is deleted when an ACL containing an ACE that references the specified counter lable name is removed from an interface. | 1.3.6.1.4.1.9.9.808.1.2.1 | not-accessible | current | |
| caAclLabelIntfStatsEntry OBJECT-TYPE Each entry in this table provides the aggregated counters for all ACEs applied on the given interface/direction that have been assigned the same counter label. | 1.3.6.1.4.1.9.9.808.1.2.1.1 | not-accessible | current | |
| caAclIntfStatsCounterLabelName OBJECT-TYPE The counter label index associated with this set of statistics. | 1.3.6.1.4.1.9.9.808.1.2.1.1.1 | SnmpAdminString (SIZE(1..64)) | not-accessible | current |
| caAclIntfStatsPackets OBJECT-TYPE The total number of packets that match this counter label. | 1.3.6.1.4.1.9.9.808.1.2.1.1.2 | Counter64 | read-only | current |
| caAclIntfStatsOctets OBJECT-TYPE The total number of octets that match this counter label. | 1.3.6.1.4.1.9.9.808.1.2.1.1.3 | Counter64 | read-only | current |
| caAclMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.2 | |||
| caAclMIBACEConform OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.2.1 | |||
| caAclMIBACECompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.2.1.1 | |||
| caAclMIBCfgGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.808.2.1.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| caAclMIBCompliance MODULE-COMPLIANCE This compliance statement specifies the minimal requirements that an implementation must meet in order to claim full compliance with the definitions of the C-ACL-MIB. | 1.3.6.1.4.1.9.9.808.2.1.1.1 | current |
| caAclMIBCfgGroup OBJECT-GROUP This group contains objects describing ACLs. | 1.3.6.1.4.1.9.9.808.2.1.2.1 | current |
| caAclIPV4ACLMIBACEGroup OBJECT-GROUP This group is a collection of objects providing IPV4 ACE feature. | 1.3.6.1.4.1.9.9.808.2.1.2.2 | current |
| caAclIPV6ACLMIBACEGroup OBJECT-GROUP This group is a collection of objects providing IPV6 ACE feature. | 1.3.6.1.4.1.9.9.808.2.1.2.3 | current |
| caAclMIBAccessGroupCfgGroup OBJECT-GROUP This group contains the objects describing the access group configuration. | 1.3.6.1.4.1.9.9.808.2.1.2.4 | current |
| caAclMIBCounterGroup OBJECT-GROUP This group contains the objects describing the ACE counter label. | 1.3.6.1.4.1.9.9.808.2.1.2.5 | current |