MIBs Depot

BWA-DOT11-WLAN-MIB

Last updated
1907-08-14 11:46
Organization
BWA Products
Revisions
1907-08-14 11:46
Namespace
alvarion
Source file
BWA-DOT11-WLAN-MIB
Digest
sha256:be86229d80dc0c6d24873c7b3a14693d531579a363e4aaef76237cdfc1410ec4

Description

BWA VL products, BWA 4900, BWA-PtP

Contact

Contact Man Postal: BWA Products Street Number ZipCode Country Tel: 000-0-0000000 Fax: 000-0-0000000 E-mail: E-mail

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BWA-DOT11-WLAN-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
DisplayString
type
MacAddress
type

Objects

NameOIDSyntaxAccessStatus
bwa
OBJECT-IDENTITY
1.3.6.1.4.1.12394
products
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1
bwaVLSysInfo
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.1
bwaVLUnitHwVersion
OBJECT-TYPE
Applicable to all units. Hardware platform version.
1.3.6.1.4.1.12394.1.1.1.1DisplayString (SIZE(0..32))read-onlycurrent
bwaVLRunningSoftwareVersion
OBJECT-TYPE
Applicable to all units. Running software version.
1.3.6.1.4.1.12394.1.1.1.2DisplayString (SIZE(0..32))read-onlycurrent
bwaVLRunningFrom
OBJECT-TYPE
Applicable to all units. The memory (main or shadow) from which the current version is running from.
1.3.6.1.4.1.12394.1.1.1.3INTEGER {mainVersion(1), shadowVersion(2)}read-onlycurrent
bwaVLMainVersionNumber
OBJECT-TYPE
Applicable to all units. Main software version number.
1.3.6.1.4.1.12394.1.1.1.4DisplayString (SIZE(0..32))read-onlycurrent
bwaVLMainVersionFileName
OBJECT-TYPE
Applicable to all units. Main software version file name.
1.3.6.1.4.1.12394.1.1.1.5DisplayString (SIZE(0..32))read-onlycurrent
bwaVLShadowVersionNumber
OBJECT-TYPE
Applicable to all units. Shadow software version number.
1.3.6.1.4.1.12394.1.1.1.6DisplayString (SIZE(0..32))read-onlycurrent
bwaVLShadowVersionFileName
OBJECT-TYPE
Applicable to all units. Shadow software version file name.
1.3.6.1.4.1.12394.1.1.1.7DisplayString (SIZE(0..32))read-onlycurrent
bwaVLUnitMacAddress
OBJECT-TYPE
Applicable to all units. Unit hardware MAC address.
1.3.6.1.4.1.12394.1.1.1.8MacAddressread-onlycurrent
bwaVLUnitType
OBJECT-TYPE
Applicable to all units. auBS (1) : AU-BS (modular access unit). auSA (2) : AU-SA (stand-alone access unit). su-6-1D (3) : SU-6-1D (subscriber unit supporting 6 Mbps) su-6-BD (4) : SU-6-BD (subscriber unit supporting 6 Mbps). su-24-BD (5) : SU-24-BD (subscriber unit supporting 24 Mbps). bu-B14 (6) : BU-B14 (PtP Base Unit supporting 14 Mbps). bu-B28 (7) : BU-B28 (PtP Base Unit supporting 28 Mbps). rb-B14 (8) : RB-B14 (PtP Remote Bridge supporting 14 Mbps). rb-B28 (9) : RB-B28 (PtP Remote Bridge supporting 28 Mbps). su-BD (10) : SU-BD (subscriber unit). su-54-BD(11) : SU-54-BD (subscriber unit supporting 54 Mbps). su-3-1D (12) : SU-3-1D (subscriber unit supporting 3 Mbps). su-3-4D (13) : SU-3-4D (subscriber unit supporting 3 Mbps). ausBS (14) : AUS-BS (modular access unit supporting maxim 8 or 25 (via licensing) subscribers and allowing association only with SU-3 or SU-6). ausSA (15) : AUS-SA (stand-alone access unit supporting maxim 8 or 25 (via licensing)subscribers and allowing association only with SU-3 or SU-6 ). auBS4900(16) : AU-BS-4900 (BWA 4900 modular access unit) auSA4900(17) : AU-SA-4900 (BWA 4900 stand alone access unit) suBD4900(18) : SU-BD-4900 (BWA 4900 subscriber unit) bu-B100 (19) : BU-B100 (PtP Base Unit unlimited throughput) rb-B100 (20) : BU-B100 (PtP Remote Bridge unlimited throughput) su-I (21) : SU-I au-E (22) : AU-E
1.3.6.1.4.1.12394.1.1.1.9INTEGER {auBS(1), auSA(2), su-6-1D(3), su-6-BD(4), su-24-BD(5), bu-B14(6), bu-B28(7), rb-B14(8), rb-B28(9), su-BD(10), su-54-BD(11), su-3-1D(12), su-3-4D(13), ausBS(14), ausSA(15), auBS4900(16), auSA4900(17), su4900(18), bu-B100(19), rb-B100(20), su-I(21), au-E(22)}read-onlycurrent
bwaVLAssociatedAU
OBJECT-TYPE
Applicable to SU/RB only. Associated AU/BU MAC address.
1.3.6.1.4.1.12394.1.1.1.10MacAddressread-onlycurrent
bwaVLNumOfAssociationsSinceLastReset
OBJECT-TYPE
Applicable to all units. The number of associations since last reset, including duplicate associations (re-associations).
1.3.6.1.4.1.12394.1.1.1.11INTEGERread-onlycurrent
bwaVLCurrentNumOfAssociations
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. The number of SUs currently associated with the AU. BWA-PtP products return 65535.
1.3.6.1.4.1.12394.1.1.1.13INTEGERread-onlycurrent
bwaVLUnitBootVersion
OBJECT-TYPE
Applicable to all units. Boot version.
1.3.6.1.4.1.12394.1.1.1.14DisplayString (SIZE(0..32))read-onlycurrent
bwaVLRadioBand
OBJECT-TYPE
Applicable to all units. The unit's radio band.
1.3.6.1.4.1.12394.1.1.1.15INTEGER {band-5-8GHz(1), band-5-4GHz(2), band-4-9GHz(3), band-5-2GHz(4), band-2-4GHz(5), band-5-3GHz(6), band-4-9GHzJapan(7)}read-onlycurrent
bwaVLCurrentEthernetPortState
OBJECT-TYPE
Applicable to all units. The current Ethernet port state.
1.3.6.1.4.1.12394.1.1.1.16INTEGER {halfDuplexAnd10Mbps(1), fullDuplexAnd10Mbps(2), halfDuplexAnd100Mbps(3), fullDuplexAnd100Mbps(4), linkDown(5)}read-onlycurrent
bwaVLTimeSinceLastReset
OBJECT-TYPE
Applicable to all units. The elapsed time since last reset.
1.3.6.1.4.1.12394.1.1.1.17DisplayString (SIZE(0..32))read-onlycurrent
bwaVLCountryDependentParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.1.18
bwaVLCountryCode
OBJECT-TYPE
Applicable to all units. The country code and country name or country group name that is supported by the unit.
1.3.6.1.4.1.12394.1.1.1.18.1DisplayString (SIZE(0..32))read-onlycurrent
bwaVLCountryDependentParamsTable
OBJECT-TYPE
Applicable to all units. A table of country dependent parameters.
1.3.6.1.4.1.12394.1.1.1.18.2not-accessiblecurrent
bwaVLCountryDependentParameterEntry
OBJECT-TYPE
Applicable to all units. An entry in the Country Dependent Parameters table.
1.3.6.1.4.1.12394.1.1.1.18.2.1not-accessiblecurrent
bwaVLCountryDependentParameterTableIdx
OBJECT-TYPE
Applicable to all units. The sub-band ID of the entry in the Country Dependent Parameters table. Serves also as index for the table entry.
1.3.6.1.4.1.12394.1.1.1.18.2.1.1INTEGER (1..5)read-onlycurrent
bwaVLCountryDependentParameterFrequencies
OBJECT-TYPE
Applicable to all units. The frequencies included in the applicable sub-band entry.
1.3.6.1.4.1.12394.1.1.1.18.2.1.2DisplayStringread-onlycurrent
bwaVLAllowedBandwidth
OBJECT-TYPE
Applicable to all units. The bandwidth when using the applicable the sub-band.
1.3.6.1.4.1.12394.1.1.1.18.2.1.3INTEGERread-onlycurrent
bwaVLRegulationMaxTxPowerAtAntennaPort
OBJECT-TYPE
Applicable to all units. The maximum allowed Tx power when using the applicable sub-band. A RegulationMaxTxPowerAtAntennaPort of 255, means no limit
1.3.6.1.4.1.12394.1.1.1.18.2.1.4INTEGERread-onlycurrent
bwaVLRegulationMaxEIRP
OBJECT-TYPE
Applicable to all units. The maximum Tx EIRP when using the applicable sub-band. A Regulation Max EIRP of 0, means no limit.
1.3.6.1.4.1.12394.1.1.1.18.2.1.5INTEGERread-onlycurrent
bwaVLMinModulationLevel
OBJECT-TYPE
Applicable to all units. The minimum supported modulation level.
1.3.6.1.4.1.12394.1.1.1.18.2.1.6INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-onlycurrent
bwaVLMaxModulationLevel
OBJECT-TYPE
Applicable to all units. The maximum supported modulation level.
1.3.6.1.4.1.12394.1.1.1.18.2.1.7INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-onlycurrent
bwaVLBurstModeSupport
OBJECT-TYPE
Applicable to all units. The supported Burst Mode Option.
1.3.6.1.4.1.12394.1.1.1.18.2.1.8INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLMaximumBurstDuration
OBJECT-TYPE
Applicable to all units. Applicable only if Burst Mode Option is supported. The maximum supported burst duration.
1.3.6.1.4.1.12394.1.1.1.18.2.1.9INTEGERread-onlycurrent
bwaVLDfsSupport
OBJECT-TYPE
Applicable to AU/BU only. The supported Dfs Option.
1.3.6.1.4.1.12394.1.1.1.18.2.1.10INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLMinimumHwRevision
OBJECT-TYPE
Applicable to all units. The Minimum HW Revision needed to support the country code.
1.3.6.1.4.1.12394.1.1.1.18.2.1.11INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
bwaVLAuthenticationEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported Authentication Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.3INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLDataEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported Data Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.4INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLAESEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported AES Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.5INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLAntennaGainChange
OBJECT-TYPE
Applicable to all units. Indicates whether the Antenna Gain parameter is changeable or fixed.
1.3.6.1.4.1.12394.1.1.1.19INTEGER {supported(1), notSupported(2)}read-onlycurrent
bwaVLAteTestResults
OBJECT-TYPE
Applicable to all units. Results of ATE Test
1.3.6.1.4.1.12394.1.1.1.20INTEGER {none(0), pass(1), fail(2)}read-onlycurrent
bwaVLSerialNumber
OBJECT-TYPE
Applicable to all units. Serial Number of the unit
1.3.6.1.4.1.12394.1.1.1.21DisplayString (SIZE(0..35))read-onlycurrent
bwaVLUnitControl
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2
bwaVLResetUnit
OBJECT-TYPE
Applicable to all units. Resets the unit and applies new parameter values.
1.3.6.1.4.1.12394.1.1.2.1INTEGER {cancel(1), resetSystemNow(2)}read-writecurrent
bwaVLSetDefaults
OBJECT-TYPE
Applicable to all units. Sets unit configuration to Defaults values after the next reset. noDefaultSettingRequested : Read-Only Option, no Default setting was Issued. completeFactory : All parameters revert to Factory Defaults values. partialFactory : All parameters revert to Factory Defaults values, except the parameters required for maintaining wireless connectivity. completeOperator: All parameters revert to Operator Defaults values. partialOperator : All parameters revert to Operator Defaults values, except the parameters required for maintaining wireless connectivity. cancelCurrentPendingRequest : Default Setting request is cancelled.
1.3.6.1.4.1.12394.1.1.2.2INTEGER {noDefaultSettingRequested(0), completeFactory(1), partialFactory(2), completeOperator(3), partialOperator(4), cancelCurrentPendingRequest(5)}read-writecurrent
bwaVLUnitName
OBJECT-TYPE
Applicable to all units. The unit name. A string of up to 32 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.3DisplayString (SIZE(0..32))read-writecurrent
bwaVLFlashMemoryControl
OBJECT-TYPE
Applicable to all units. resetAndBootFromShadowVersion : Activates the backup version. useRunningVersionAfterReset : The currently active version will become the main version and will be activated after next reset.
1.3.6.1.4.1.12394.1.1.2.4INTEGER {resetAndBootFromShadowVersion(1), useRunningVersionAfterReset(2), cancel(3)}read-writecurrent
bwaVLTelnetLogoutTimer
OBJECT-TYPE
Applicable to all units. Time-out of management via Telnet program. Automatic exit if the program is inactive for the defined time. Range: 1 to 999 (minutes).
1.3.6.1.4.1.12394.1.1.2.5INTEGERread-writecurrent
bwaVLSaveCurrentConfigurationAsOperatorDefaults
OBJECT-TYPE
Applicable to all units. Saves the current configuration as Operator Defaults. Cannot be executed after requesting set defaults and the unit was not reset.
1.3.6.1.4.1.12394.1.1.2.6INTEGER {saveAsDefaults(1), cancel(2)}read-writecurrent
bwaVLExitTelnet
OBJECT-TYPE
Applicable to all units. Exit the management via Telnet program.
1.3.6.1.4.1.12394.1.1.2.7INTEGER {cancelOperation(1), exit(2)}read-writecurrent
bwaVLUnitPasswords
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.8
bwaVLReadOnlyPassword
OBJECT-TYPE
Applicable to all units. The User (read only) password. This is also the Read Community String. Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.1DisplayString (SIZE(1..8))read-writecurrent
bwaVLInstallerPassword
OBJECT-TYPE
Applicable to all units. The Installer password. Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.2DisplayString (SIZE(1..8))read-writecurrent
bwaVLAdminPassword
OBJECT-TYPE
Applicable to all units. The Administrator password. Accessible only with SNMP Write Community String (administrator password). Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.3DisplayString (SIZE(1..8))read-writecurrent
bwaVLEthernetNegotiationMode
OBJECT-TYPE
Applicable to all units. The speed/duplex mode of the Ethernet port.
1.3.6.1.4.1.12394.1.1.2.9INTEGER {force10MbpsAndHalfDuplex(1), force10MbpsAndFullDuplex(2), force100MbpsAndHalfDuplex(3), force100MbpsAndFullDuplex(4), autoNegotiationMode(5)}read-writecurrent
bwaVLFTPParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10
bwaVLFTPServerParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.1
bwaVLFTPServerUserName
OBJECT-TYPE
Applicable to all units. The user name to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
1.3.6.1.4.1.12394.1.1.2.10.1.1DisplayString (SIZE(0..18))read-writecurrent
bwaVLFTPServerPassword
OBJECT-TYPE
Applicable to all units. The password to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
1.3.6.1.4.1.12394.1.1.2.10.1.2DisplayString (SIZE(0..18))read-writecurrent
bwaVLFTPClientIPAddress
OBJECT-TYPE
Applicable to all units. For SW version higher than 4.0 this is read-only. The IP address of the FTP stack in the unit.
1.3.6.1.4.1.12394.1.1.2.10.1.3IpAddressread-writecurrent
bwaVLFTPServerIpAddress
OBJECT-TYPE
Applicable to all units. The IP address of the FTP server.
1.3.6.1.4.1.12394.1.1.2.10.1.4IpAddressread-writecurrent
bwaVLFTPClientMask
OBJECT-TYPE
Applicable to all units. The Mask of the FTP stack in the unit.
1.3.6.1.4.1.12394.1.1.2.10.1.5IpAddressread-writecurrent
bwaVLFTPGatewayIpAddress
OBJECT-TYPE
Applicable to all units. The FTP Gateway address
1.3.6.1.4.1.12394.1.1.2.10.1.6IpAddressread-writecurrent
bwaVLFTPSwDownload
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.2
bwaVLFTPSwFileName
OBJECT-TYPE
Applicable to all units. The name of the SW file to be downloaded.
1.3.6.1.4.1.12394.1.1.2.10.2.1DisplayString (SIZE(1..20))read-writecurrent
bwaVLFTPSwSourceDir
OBJECT-TYPE
Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
1.3.6.1.4.1.12394.1.1.2.10.2.2DisplayString (SIZE(0..80))read-writecurrent
bwaVLFTPDownloadSwFile
OBJECT-TYPE
Applicable to all units. Execution of the SW download operation
1.3.6.1.4.1.12394.1.1.2.10.2.3INTEGER {downloadFile(1), cancel(2)}read-writecurrent
bwaVLConfigurationFileLoading
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.3
bwaVLConfigurationFileName
OBJECT-TYPE
Applicable to all units. The name of the configuration file to be downloaded/uploaded.
1.3.6.1.4.1.12394.1.1.2.10.3.1DisplayString (SIZE(1..20))read-writecurrent
bwaVLOperatorDefaultsFileName
OBJECT-TYPE
Applicable to all units. The name of the Operator Defaults file to be downloaded/uploaded
1.3.6.1.4.1.12394.1.1.2.10.3.2DisplayString (SIZE(1..20))read-writecurrent
bwaVLFTPConfigurationFileSourceDir
OBJECT-TYPE
Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
1.3.6.1.4.1.12394.1.1.2.10.3.3DisplayString (SIZE(0..80))read-writecurrent
bwaVLExecuteFTPConfigurationFileLoading
OBJECT-TYPE
Applicable to all units. Execution of the file download/upload operation.
1.3.6.1.4.1.12394.1.1.2.10.3.4INTEGER {executeFTPGetConfigurationFile(1), executeFTPPutConfigurationFile(2), executeFTPGetOperatorDefaults(3), executeFTPPutOperatorDefaults(4), cancel(5)}read-writecurrent
bwaVLEventLogFileUploading
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.4
bwaVLEventLogFileName
OBJECT-TYPE
Applicable to all units. The name of the Event Log file to be uploaded.
1.3.6.1.4.1.12394.1.1.2.10.4.1DisplayString (SIZE(1..20))read-writecurrent
bwaVLEventLogDestinationDir
OBJECT-TYPE
Applicable to all units. The destination directory of the event log file. Up to 80 printable ASCII characters. Use dot (.) To clear field.
1.3.6.1.4.1.12394.1.1.2.10.4.2DisplayString (SIZE(0..80))read-writecurrent
bwaVLUploadEventLogFile
OBJECT-TYPE
Applicable to all units. Execution of the event log upload operation.
1.3.6.1.4.1.12394.1.1.2.10.4.3INTEGER {uploadFile(1), cancel(2)}read-writecurrent
bwaVLLoadingStatus
OBJECT-TYPE
Applicable to all units. The status of the last loading operation.
1.3.6.1.4.1.12394.1.1.2.11INTEGER {inProcess(1), successful(2), failed(3)}read-onlycurrent
bwaVLEventLogFileParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.12
bwaVLEventLogPolicy
OBJECT-TYPE
Applicable to all units. The lowest level event to be registered in the event log.
1.3.6.1.4.1.12394.1.1.2.12.1INTEGER {message(1), warning(2), error(3), fatal(4), logNone(5)}read-writecurrent
bwaVLEraseEventLog
OBJECT-TYPE
Applicable to all units. Erase the event log.
1.3.6.1.4.1.12394.1.1.2.12.2INTEGER {eraseEventLog(1), cancel(2)}read-writecurrent
bwaVLSystemLocation
OBJECT-TYPE
Applicable to all units. The unit location.
1.3.6.1.4.1.12394.1.1.2.13DisplayString (SIZE(0..34))read-writecurrent
bwaVLFeatureUpgrade
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.14
bwaVLFeatureUpgradeManually
OBJECT-TYPE
Applicable to all units. Upgrade unit to support new feature. Enter your license number (32 to 64 hex digits).
1.3.6.1.4.1.12394.1.1.2.14.1DisplayString (SIZE(32..64))read-writecurrent
bwaVLChangeUnitType
OBJECT-TYPE
Applicable RB/BU only. Change the unit type between BU and RB.
1.3.6.1.4.1.12394.1.1.2.15INTEGER {bu(1), rb(2), cancel(3)}read-writecurrent
bwaLighteAPWorkingMode
OBJECT-TYPE
Applicable to AU only. Change unit running mode: 0 - VL mode 1 - Mixed cell mode
1.3.6.1.4.1.12394.1.1.2.16INTEGERread-writecurrent
bwaVLNwMngParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.3
bwaVLAccessToNwMng
OBJECT-TYPE
Applicable to all units. The port to be used for remote management.
1.3.6.1.4.1.12394.1.1.3.1INTEGER {fromWirelessOnly(1), fromEthernetOnly(2), fromBothWirelessAndEthernet(3), na(255)}read-writecurrent
bwaVLNwMngFilter
OBJECT-TYPE
Applicable to all units. Disables or enable on one of the ports, or on both ports, IP address based filtering of management messages (e.g. SNMP , Telnet , TFTP , DHCP).
1.3.6.1.4.1.12394.1.1.3.2INTEGER {disable(1), activateOnEthernetPort(2), activateOnWirelessPort(3), activateOnBothWirelessAndEthernet(4), na(255)}read-writecurrent
mngIpFilterTable
OBJECT-TYPE
Applicable to all units. A Management IP Filter Table of up to 3 IP addresses of devices that are authorized to access the unit for management purposes.
1.3.6.1.4.1.12394.1.1.3.3not-accessiblecurrent
mngIpFilterEntry
OBJECT-TYPE
Applicable to all units. A Management IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.3.3.1not-accessiblecurrent
bwaVLNwMngIpAddress
OBJECT-TYPE
Applicable to all units. An IP address in the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.3.1.1IpAddressread-writecurrent
bwaVLNwMngIpTableIdx
OBJECT-TYPE
Applicable to all units. A table index for an entry in the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.3.1.2INTEGER (1..10)read-onlycurrent
bwaVLDeleteOneNwIpAddr
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.4INTEGER (0 | 1..10 | 255)read-writecurrent
bwaVLDeleteAllNwIpAddrs
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.5INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
bwaVLAccessToNwTrap
OBJECT-TYPE
Applicable to all units. Enables or disables sending of traps.
1.3.6.1.4.1.12394.1.1.3.6INTEGER {disable(1), enable(2)}read-writecurrent
mngTrapTable
OBJECT-TYPE
Applicable to all units. A Management Trap Table of up to 10 IP addresses of stations to send traps to.
1.3.6.1.4.1.12394.1.1.3.7not-accessiblecurrent
mngTrapEntry
OBJECT-TYPE
Applicable to all units. A Management Trap Table entry.
1.3.6.1.4.1.12394.1.1.3.7.1not-accessiblecurrent
bwaVLNwMngTrapCommunity
OBJECT-TYPE
Applicable to all units. The trap community associated with the applicable entry in the Management Trap Table. Up to 14 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.3.7.1.1DisplayString (SIZE(0..14))read-writecurrent
bwaVLNwMngTrapAddress
OBJECT-TYPE
Applicable to all units. An IP address in the Management Trap Table entry.
1.3.6.1.4.1.12394.1.1.3.7.1.2IpAddressread-writecurrent
bwaVLNwTrapTableIdx
OBJECT-TYPE
Applicable to all units. Tables Index for an entry in the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.7.1.3INTEGER (1..10)read-onlycurrent
bwaVLDeleteOneTrapAddr
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.8INTEGER (0 | 1..10 | 255)read-writecurrent
bwaVLDeleteAllTrapAddrs
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.9INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
bwaVLMngIpRangesTable
OBJECT-TYPE
Applicable to all units. Table of Management IP Address Ranges
1.3.6.1.4.1.12394.1.1.3.10not-accessiblecurrent
bwaVLMngIpRangeEntry
OBJECT-TYPE
Applicable to all units. A Management IP Address Ranges Table entry
1.3.6.1.4.1.12394.1.1.3.10.1not-accessiblecurrent
bwaVLMngIpRangeIdx
OBJECT-TYPE
Applicable to all units. Index of an entry in the Management IP Address Ranges Table
1.3.6.1.4.1.12394.1.1.3.10.1.1INTEGER (1..10)read-onlycurrent
bwaVLMngIpRangeFlag
OBJECT-TYPE
Applicable to all units. Defines the method of defining the range: Using Start & End Address( rangeDefinedByStartEndAddr ), or using Start Address and Mask ( rangeDefinedByStartAddrSubNetMask ).
1.3.6.1.4.1.12394.1.1.3.10.1.2INTEGER {rangeDefinedByStartEndAddr(1), rangeDefinedByStartAddrMask(2)}read-writecurrent
bwaVLMngIpRangeStart
OBJECT-TYPE
Applicable to all units. Start Address of the range
1.3.6.1.4.1.12394.1.1.3.10.1.3IpAddressread-writecurrent
bwaVLMngIpRangeEnd
OBJECT-TYPE
Applicable to all units. End Address of the range. Used only if bwaVLMngIpRangeFlag is rangeDefinedByStartEndAddr
1.3.6.1.4.1.12394.1.1.3.10.1.4IpAddressread-writecurrent
bwaVLMngIpRangeMask
OBJECT-TYPE
Applicable to all units. End Address of the range. Used only if bwaVLMngIpRangeFlag is rangeDefinedByStartAddrMask
1.3.6.1.4.1.12394.1.1.3.10.1.5IpAddressread-writecurrent
bwaVLDeleteOneNwIpRange
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Ranges Table.
1.3.6.1.4.1.12394.1.1.3.11INTEGER (0 | 1..10 | 255)read-writecurrent
bwaVLDeleteAllNwIpRanges
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management IP Ranges Table.
1.3.6.1.4.1.12394.1.1.3.12INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
bwaVLApClientIpAddress
OBJECT-TYPE
Applicable to SU/RB unit only. The IP Address of the WIFI WIMAX unit
1.3.6.1.4.1.12394.1.1.3.13IpAddressread-writecurrent
bwaVLIpParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.4
bwaVLUnitIpAddress
OBJECT-TYPE
Applicable to all units. IP address of the unit.
1.3.6.1.4.1.12394.1.1.4.1IpAddressread-writecurrent
bwaVLSubNetMask
OBJECT-TYPE
Applicable to all units. Subnet mask of the unit.
1.3.6.1.4.1.12394.1.1.4.2IpAddressread-writecurrent
bwaVLDefaultGWAddress
OBJECT-TYPE
Applicable to all units. Default gateway IP address of the unit.
1.3.6.1.4.1.12394.1.1.4.3IpAddressread-writecurrent
bwaVLUseDhcp
OBJECT-TYPE
Applicable to all units. DHCP client mode of operation. disabled : Use regular (manual) methods to configure IP parameters. dHCP Only: Use DHCP server to configure IP parameters. automatic: Use DHCP server to configure IP parameters. If a DHCP server is not available, use manually configured values.
1.3.6.1.4.1.12394.1.1.4.4INTEGER {disable(1), dhcpOnly(2), automatic(3)}read-writecurrent
bwaVLAccessToDHCP
OBJECT-TYPE
Applicable to all units. The port to be used for communicating with a DHCP server.
1.3.6.1.4.1.12394.1.1.4.5INTEGER {fromWirelessOnly(1), fromEthernetOnly(2), fromBothWirelessAndEthernet(3)}read-writecurrent
bwaVLRunTimeIPaddr
OBJECT-TYPE
Applicable to all units. The run-time IP address. If DHCP is used the Run Time IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
1.3.6.1.4.1.12394.1.1.4.6IpAddressread-onlycurrent
bwaVLRunTimeSubNetMask
OBJECT-TYPE
Applicable to all units. The run-time Subnet Mask. If DHCP is used the Run Time Subnet Mask is the mask given to the unit by the server. Otherwise it is the manually configured mask.
1.3.6.1.4.1.12394.1.1.4.7IpAddressread-onlycurrent
bwaVLRunTimeDefaultIPGateway
OBJECT-TYPE
Applicable to all units. The run-time Gateway IP address. If DHCP is used the Run Time Gateway IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
1.3.6.1.4.1.12394.1.1.4.8IpAddressread-onlycurrent
bwaVLBridgeParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5
bwaVLVLANSupport
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1
bwaVLVlanID
OBJECT-TYPE
Applicable to SU/RB only. VLAN ID for data frame tagging. Applicable to Access Link only. Range: 1 to 4094. 0 - not applicable.
1.3.6.1.4.1.12394.1.1.5.1.1INTEGERread-writecurrent
bwaVLEthernetLinkType
OBJECT-TYPE
Applicable to all units. VLAN support mode (Link Type). The Access Link option is not available for AU/BU. Service Provider Link is not available for BU/RB.
1.3.6.1.4.1.12394.1.1.5.1.2INTEGER {accessLink(1), trunkLink(2), hybridLink(3), serviceProviderLink(4)}read-writecurrent
bwaVLManagementVlanID
OBJECT-TYPE
Applicable to all units. VLAN ID for management frame tagging. Range: 1 to 4094, 65535 for No VLAN tagging.
1.3.6.1.4.1.12394.1.1.5.1.3INTEGERread-writecurrent
bwaVLVLANForwarding
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.4
bwaVLVlanForwardingSupport
OBJECT-TYPE
Applicable to all units. Enables or disables the VLAN forwarding feature. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLVlanForwardingTable
OBJECT-TYPE
Applicable to all units. A VLAN Forwarding Table of up to 20 VLAN IDs of devices to which data frames are forwarded when VLAN Forwarding is Enabled. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.2not-accessiblecurrent
bwaVLVlanForwardingEntry
OBJECT-TYPE
Applicable to all units. A VLAN Forwarding Table entry. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.2.1not-accessiblecurrent
bwaVLVlanForwardingTableIdx
OBJECT-TYPE
Applicable to all units. A read only table index for a VLAN entry in the VLAN Forwarding Table.
1.3.6.1.4.1.12394.1.1.5.1.4.2.1.1INTEGER (1..20)read-onlycurrent
bwaVLVlanIdForwarding
OBJECT-TYPE
Applicable to all units. The list of VLAN ID's in the VLAN ID Forwarding Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range : 0 to 4094
1.3.6.1.4.1.12394.1.1.5.1.4.2.1.2INTEGERread-writecurrent
bwaVLVlanRelaying
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.5
bwaVLVlanRelayingSupport
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. Enables or disables VLAN Relaying (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLVlanRelayingTable
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. A VLAN Relaying Table of up to 20 VLAN IDs of devices to which data frames are relayed when VLAN Relaying is Enabled. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.2not-accessiblecurrent
bwaVLVlanRelayingEntry
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. A VLAN Relaying Table entry. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.2.1not-accessiblecurrent
bwaVLVlanRelayingTableIdx
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. A table index for a VLAN entry in the VLAN Relaying Table.
1.3.6.1.4.1.12394.1.1.5.1.5.2.1.1INTEGER (1..20)read-onlycurrent
bwaVLVlanIdRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. The list of VLAN ID's in the VLAN ID Relaying Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range: 0 to 4094 , 0 - remove entry.
1.3.6.1.4.1.12394.1.1.5.1.5.2.1.2INTEGERread-writecurrent
bwaVLVLANTrafficPriority
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.6
bwaVLVlanDataPriority
OBJECT-TYPE
Applicable to SU/RB only. Priority tagging for data frames. Applicable to Access Link only. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.1.6.1INTEGER {na(255)}read-writecurrent
bwaVLVlanManagementPriority
OBJECT-TYPE
Applicable to all units. Priority tagging for management frames. Applicable to Access Link and Trunk Link only. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.1.6.2INTEGER {na(255)}read-writecurrent
bwaVLVlanPriorityThreshold
OBJECT-TYPE
Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold for tagged frames received from Ethernet port. Applicable to Hybrid Link and Trunk Link only. Valid values: 0-7.
1.3.6.1.4.1.12394.1.1.5.1.6.3INTEGER {na(255)}read-writecurrent
bwaVLVLANQinQ
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.7
bwaVLQinQEthertype
OBJECT-TYPE
Applicable to AU and SU. Not applicable to PtP units. The Ethernet type of the Service Provider Tag. The range is 0x8101(33025) - 0x9000(36864), 0x9100(37120), 0x9200(37376).
1.3.6.1.4.1.12394.1.1.5.1.7.1INTEGER (33025..36864 | 37120 | 37376)read-writecurrent
bwaVLQinQProviderVlanID
OBJECT-TYPE
Applicable to SU only. VLAN ID of the Service Provider Tag.
1.3.6.1.4.1.12394.1.1.5.1.7.2INTEGER (1..4094)read-writecurrent
bwaVLBridgeAgingTime
OBJECT-TYPE
Applicable to all units. Bridge aging time for devices on both the Ethernet and wireless link sides. Range: 20 to 2000 seconds.
1.3.6.1.4.1.12394.1.1.5.2INTEGERread-writecurrent
bwaVLBroadcastRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. Enables/disables the relaying of broadcast messages to the wireless link.
1.3.6.1.4.1.12394.1.1.5.4INTEGER {disable(1), broadcastMulticastEnable(2), broadcastEnable(3), multicastEnable(4), na(255)}read-writecurrent
bwaVLUnicastRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. Enables/disables the relaying of unicast messages to the wireless link.
1.3.6.1.4.1.12394.1.1.5.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLEthBroadcastFiltering
OBJECT-TYPE
Applicable to SU/RB only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable : No filtering. onEthernetOnly : Filters broadcasts received on the Ethernet port only. onWirelessOnly : Filters broadcasts received on the Wlan port only. onBothWirelessAndEth: Filters broadcasts received on both ports.
1.3.6.1.4.1.12394.1.1.5.6INTEGER {disable(1), onEthernetOnly(2), onWirelessOnly(3), onBothWirelessAndEthernet(4), na(255)}read-writecurrent
bwaVLEthBroadcastingParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.7
bwaVLDHCPBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of DHCP messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLPPPoEBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of PPPoE messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLARPBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of ARP messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.3INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLEthBroadcastMulticastLimiterOption
OBJECT-TYPE
Applicable to all units. Enable/disable the limiter for multicast and broadcast packets.
1.3.6.1.4.1.12394.1.1.5.7.4INTEGER {disable(1), limitOnlyBroadcasts(2), limitMulticastsExceptBroadcasts(3), limitAllMulticasts(4)}read-writecurrent
bwaVLEthBroadcastMulticastLimiterThreshold
OBJECT-TYPE
Applicable to all units. The limit on the number of multicast and broadcast packets when the Ethernet Broadcast/Multicast Limiter Option is enabled. Range: 0 to 204800
1.3.6.1.4.1.12394.1.1.5.7.5INTEGERread-writecurrent
bwaVLEthBroadcastMulticastLimiterSendTrapInterval
OBJECT-TYPE
Applicable to all units. The minimum time between two successive traps that are sent indicating the number of packets that were dropped by the Ethernet Broadcast/Multicast Limiter since the last trap was sent. Range: 1 to 60 minutes
1.3.6.1.4.1.12394.1.1.5.7.6INTEGERread-writecurrent
bwaVLToSPriorityParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.8
bwaVLToSPrecedenceThreshold
OBJECT-TYPE
Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold (based on the ToS) for frames received from the Ethernet port. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.8.1INTEGERread-writecurrent
bwaVLRoamingOption
OBJECT-TYPE
Applicable to SU/RB only. Disable/enable the roaming feature. When enabled, the SU/RB will start scanning for an AU/BU after about one second of not receiving beacons or data from current AU/BU. Once it found a new AU/BU, it will also send through the wireless network a roaming SNAP on behalf of its clients informing other devices in the network of their new location. When disabled, it will wait for about seven seconds before starting scanning, and it will not send a roaming SNAP.
1.3.6.1.4.1.12394.1.1.5.9INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLMacAddressDenyList
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.10
bwaVLMacAddressDenyListTable
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. A list of up to 100 MAC Addresses of SUs. If bwaVLMacAddressDenyListAction is set to denyList, these are SUs that are not allowed to transfer data to the AU. If bwaVLMacAddressDenyListAction is set to allowList, only these SUs are allowed to transfer data to the AU.
1.3.6.1.4.1.12394.1.1.5.10.1not-accessiblecurrent
bwaVLMacAddressDenyListEntry
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. An entry in the Mac Address Deny List Table.
1.3.6.1.4.1.12394.1.1.5.10.1.1not-accessiblecurrent
bwaVLMacAddressDenyListTableIdx
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. A read only table index for a MAC Address entry in the Mac Address Deny List Table. Range: 1 to 100.
1.3.6.1.4.1.12394.1.1.5.10.1.1.1INTEGER (1..100)read-onlycurrent
bwaVLMacAddressDenyListId
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. The list of MAC Addresses in the Mac Address Deny List Table. To Remove a MAC Address - SET the corresponding entry to 0. To Add a new MAC Address - SET an entry which is currently 0.
1.3.6.1.4.1.12394.1.1.5.10.1.1.2MacAddressread-writecurrent
bwaVLMacAddressDenyListAdd
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. Add a MAC address to the MAC Address Deny List Table
1.3.6.1.4.1.12394.1.1.5.10.2MacAddressread-writecurrent
bwaVLMacAddressDenyListRemove
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. Delete a MAC address from the MAC Address Deny List Table
1.3.6.1.4.1.12394.1.1.5.10.3MacAddressread-writecurrent
bwaVLNumberOfMacAddressesInDenyList
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP units. Number of MAC addresses in the MAC Address Deny List Table.
1.3.6.1.4.1.12394.1.1.5.10.4INTEGER {na(255)}read-onlycurrent
bwaVLMacAddressDenyListAction
OBJECT-TYPE
Applicable to AU only. Define the action to be used by the Mac Address Deny List. allowedList(2) means that the list becomes Allow list.
1.3.6.1.4.1.12394.1.1.5.10.5INTEGER {denyList(1), allowedList(2), na(255)}read-writecurrent
bwaVLPortsControl
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.11
bwaVLEthernetPortControl
OBJECT-TYPE
Applicable to SU/RB only. Enable/disable the Ethernet port. When disabled, only data frames are blocked. Management frames are accepted.
1.3.6.1.4.1.12394.1.1.5.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLAirInterface
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6
bwaVLESSIDParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.1
bwaVLESSID
OBJECT-TYPE
Applicable to all units. The Extended Service Set ID (ESSID) used to prevent the merging of collocated systems. The ESSID is accessible only with the write community string (administrator password). Up to 31 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.6.1.1DisplayString (SIZE(0..31))read-writecurrent
bwaVLOperatorESSIDOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the use of the Operator ESSID.
1.3.6.1.4.1.12394.1.1.6.1.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLOperatorESSID
OBJECT-TYPE
Applicable to AU/BU only. A secondary ESSID to support easy installation of SUs as well as the use of the Best AU/BU feature. Accessible only with SNMP Write Community Up to 31 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.6.1.3DisplayString (SIZE(0..31))read-writecurrent
bwaVLRunTimeESSID
OBJECT-TYPE
Applicable to SU/RB only. The ESSID of the associated AU/BU. Accessible only with SNMP Write Community. Up to 31 printable ASCII characters, case sensitive.
1.3.6.1.4.1.12394.1.1.6.1.4DisplayString (SIZE(31))read-onlycurrent
bwaVLMaximumCellRadius
OBJECT-TYPE
Applicable to all units. For AU/BU: read-write. In units with SW version 2.0 and up - applicable only when the Cell Distance Mode is set to Manual. The highest distance from the AU/BU of any SU/RB served by it. Affects the maximum time the units wait for a response message and the slot size by taking into account the round trip propagation delay. For SU/RB: read-only. The distance is learned from the AU/BU. Range: For units below version 2.0 the range is 0 - 50000 Meters. Otherwise - the range is 0 to 54 Kilometers. 0 means no compensation (minimum slot size, maximal delay timeout).
1.3.6.1.4.1.12394.1.1.6.2INTEGERread-writecurrent
bwaVLAIFS
OBJECT-TYPE
Applicable to AU and SU. Not applicable to BWA-PtP products. Not applicable if Wireless Link Prioritization is enabled. Arbitration Inter-Frame Spacing (AIFS) value, in slots. This is the number of time slots that define the DIFS. (DIFS=SIFS+AIFS). A value of 1 should be used only in point-to-point applications to allow one unit to have advantage over the other unit.
1.3.6.1.4.1.12394.1.1.6.3INTEGER {oneSlot(1), twoSlots(2)}read-writecurrent
bwaVLWirelessTrapThreshold
OBJECT-TYPE
Applicable to AU/BU only. A wireless link quality threshold, expressed in % of retransmissions, for sending the bwaVLAUWirelessQualityTRAP. This trap indicate whether the quality has gone below or above the specified threshold. The Threshold Range: 1 to 100 (% retransmissions).
1.3.6.1.4.1.12394.1.1.6.4INTEGERread-writecurrent
bwaVLTransmitPowerTable
OBJECT-TYPE
Applicable to all units. A table of transmit power parameters.
1.3.6.1.4.1.12394.1.1.6.5not-accessiblecurrent
bwaVLTransmitPowerEntry
OBJECT-TYPE
Applicable to all units. An entry in the Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.5.1not-accessiblecurrent
bwaVLTransmitPowerIdx
OBJECT-TYPE
Applicable to all units. An index of an entry in the Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.5.1.1INTEGER (1..4)read-onlycurrent
bwaVLApplicableModulationLevel
OBJECT-TYPE
Applicable to all units. The applicable modulation level for an entry in the Transmit Power Table. Level 8 is not applicable to units with HW revision A.
1.3.6.1.4.1.12394.1.1.6.5.1.2INTEGER {level1to5(1), level6(2), level7(3), level8(4)}read-onlycurrent
bwaVLMaximumTxPowerRange
OBJECT-TYPE
Applicable to all units. The allowed range for the bwaVLTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
1.3.6.1.4.1.12394.1.1.6.5.1.3DisplayStringread-onlycurrent
bwaVLTxPower
OBJECT-TYPE
Applicable to all units. Read-only for units with SW version 4.0 and higher. In AU/BU: The transmit power in dBm defined for the applicable rate. In SU/RB: If ATPC is disabled, this is the transmit power in dBm defined for the applicable rate. If ATPC is enabled, it serves as the initial transmit power in dBm for the ATPC algorithm. In SU/RB: The range is -10 dBm to the power value defined by bwaVLMaximumTxPower for the applicable modulation level. In AU/BU: The range is -10 dBm to the power value defined by bwaVLMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.5.1.4DisplayStringread-writecurrent
bwaVLCurrentTxPower
OBJECT-TYPE
Applicable to SU/RB. The actual transmit power in dBm for the applicable rate. Range: -17 to the maximum value defined by bwaVLMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.5.1.5DisplayStringread-onlycurrent
bwaVLMaximumTransmitPowerTable
OBJECT-TYPE
Applicable to SU/RB only. A table of maximum transmit power parameters.
1.3.6.1.4.1.12394.1.1.6.6not-accessiblecurrent
bwaVLMaximumTransmitPowerEntry
OBJECT-TYPE
Applicable to SU/RB only. An entry in the Maximum Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.6.1not-accessiblecurrent
bwaVLMaximumTransmitPowerIdx
OBJECT-TYPE
Applicable to SU/RB only. An index of an entry in the Maximum Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.6.1.1INTEGER (1..4)read-onlycurrent
bwaVLMaxTxApplicableModulationLevel
OBJECT-TYPE
Applicable to SU/RB only. The applicable modulation level for an entry in the Maximum Transmit Power Table. Level 8 is not applicable to units with HW revision A.
1.3.6.1.4.1.12394.1.1.6.6.1.2INTEGER {level1to5(1), level6(2), level7(3), level8(4)}read-onlycurrent
bwaVLDefinedMaximumTxPowerRange
OBJECT-TYPE
Applicable to SU/RB only. The allowed range for the bwaVLMaxTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
1.3.6.1.4.1.12394.1.1.6.6.1.3DisplayStringread-onlycurrent
bwaVLMaxTxPower
OBJECT-TYPE
Applicable to SU/RB only. Read-only for units with SW version 4.0 and higher. The maximum value that can be configured for the bwaVLTxPower parameter. This is also the maximum power level that can be reached by the ATPC algorithm. The range is -10 dBm to the maximum value defined by bwaVLDefinedMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.6.1.4DisplayStringread-writecurrent
bwaVLMaxNumOfAssociations
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. Sets the upper limit for the number of SUs that can be associated with the AU. Range: For regular AUs (AU-BS, AU-SA) the range is from 0 to 512 if encryption is disabled the range id form 0 to 124 if encryption is enabled For AUS-BS and AUS-SA with SW version 4.0 and higher the range is between 0 to 8 or 25 (via licensing). For AUS-BS and AUS-SA with SW version below 4.0 the range is between 0 to 5. BWA-PtP products return 65535.
1.3.6.1.4.1.12394.1.1.6.10INTEGERread-writecurrent
bwaVLBestAu
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.11
bwaVLBestAuSupport
OBJECT-TYPE
Applicable to SU/RB only. Disable/enable the Best AU/BU selection mechanism.
1.3.6.1.4.1.12394.1.1.6.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLBestAuNoOfScanningAttempts
OBJECT-TYPE
Applicable to SU/RB only. The number of scanning attempts to collect information for the Best AU/BU decision. Range: 1 to 255.
1.3.6.1.4.1.12394.1.1.6.11.2INTEGERread-writecurrent
bwaVLPreferredAuMacAddress
OBJECT-TYPE
Applicable to SU/RB only. The MAC address of the preferred AU/BU (overriding the Best AU/BU selection process). 000000000000 means no preferred AU/BU.
1.3.6.1.4.1.12394.1.1.6.11.3MacAddressread-writecurrent
bwaVLNeighborAuTable
OBJECT-TYPE
Applicable to SU/RB only. A table of data on neighboring AUs/BUs.
1.3.6.1.4.1.12394.1.1.6.11.4not-accessiblecurrent
bwaVLNeighborAuEntry
OBJECT-TYPE
Applicable to SU/RB only. An entry in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1not-accessiblecurrent
bwaVLNeighborAuIdx
OBJECT-TYPE
Applicable to SU/RB only. An index of an entry in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.1INTEGER (1..20)read-onlycurrent
bwaVLNeighborAuMacAdd
OBJECT-TYPE
Applicable to SU/RB only. A MAC address of an AU/BU in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.2MacAddressread-onlycurrent
bwaVLNeighborAuESSID
OBJECT-TYPE
Applicable to SU/RB only. The ESSID of an AU/BU in the Neighbor AU/BU Table. Accessible only with SNMP Write Community.
1.3.6.1.4.1.12394.1.1.6.11.4.1.3DisplayStringread-onlycurrent
bwaVLNeighborAuSNR
OBJECT-TYPE
Applicable to SU/RB only. The received signal quality (SNR) in dB of an AU/BU in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.4INTEGER {na(255)}read-onlycurrent
bwaVLNeighborAuAssocLoadStatus
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU association load status in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.5INTEGER {full(1), notFull(2), na(255)}read-onlycurrent
bwaVLNeighborAuMark
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU mark in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.6INTEGERread-onlycurrent
bwaVLNeighborAuHwRevision
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU HW revision in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.7INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
bwaVLNeighborAuCountryCode
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU supported country code in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.8INTEGERread-onlycurrent
bwaVLNeighborAuSwVer
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU SW version in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.9DisplayStringread-onlycurrent
bwaVLNeighborAuAtpcOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU ATPC option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.10INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuAdapModOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU adaptive modulation option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.11INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuBurstModeOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU burst mode option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.12INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuDfsOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU DFS option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.14INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuConcatenationOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU concatenation option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.15INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuLearnCountryCodeBySU
OBJECT-TYPE
Applicable to SU only. Starting with 4.0 is not applicable for BWA 4900 and BWA PtP products. Neighbor AU Learn Country Code by SU configuration in the Neighbor AU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.17INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuSecurityMode
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU security mode configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.18INTEGER {wep(1), aesOCB(2), fips197(3), na(255)}read-onlycurrent
bwaVLNeighborAuAuthOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU authentication option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.19INTEGER {openSystem(1), sharedKey(2), na(255)}read-onlycurrent
bwaVLNeighborAuDataEncyptOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU data encryption option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.20INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLNeighborAuPerSuDistanceLearning
OBJECT-TYPE
Applicable to SU only. Neighbor AU per SU distance learning option configuration in the Neighbor AU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.21INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLFrequencyDefinition
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12
bwaVLSubBandLowerFrequency
OBJECT-TYPE
Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The lowest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
1.3.6.1.4.1.12394.1.1.6.12.1INTEGERread-writeobsolete
bwaVLSubBandUpperFrequency
OBJECT-TYPE
Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The highest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
1.3.6.1.4.1.12394.1.1.6.12.2INTEGERread-writeobsolete
bwaVLScanningStep
OBJECT-TYPE
Applicable to all units - For flexible Sub-Bands only. For units with version 2.0 and above this is a read-only parameter. The scanning step to be used for generating the frequency subset.
1.3.6.1.4.1.12394.1.1.6.12.3INTEGER {mhz-5(1), mhz-10(2), mhz-20(3), na(255)}read-writecurrent
bwaVLFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all frequencies from the selected Sub-band.
1.3.6.1.4.1.12394.1.1.6.12.4not-accessiblecurrent
bwaVLFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.4.1not-accessiblecurrent
bwaVLFrequencySubsetTableIdx
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An index of an entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.4.1.1INTEGER (1..40)read-onlycurrent
bwaVLFrequencySubsetFrequency
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.4.1.2INTEGERread-onlycurrent
bwaVLFrequencySubsetActive
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.4.1.3INTEGER {active(1), notActive(2)}read-writecurrent
bwaVLFrequencySubsetFrequencyNew
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Frequency Subset table. (Replaces bwaVLFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.4.1.4DisplayStringread-writecurrent
bwaVLSetSelectedFreqSubset
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used.
1.3.6.1.4.1.12394.1.1.6.12.5INTEGER {setSelectedFreqsSubset(1), cancel(2)}read-writecurrent
bwaVLCurrentFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Current Frequency Subset table. In SU/RB it includes all frequencies that are currently used for scanning. In AU/BU it includes all frequencies that can be used by the DFS mechanism (if applicable)
1.3.6.1.4.1.12394.1.1.6.12.6not-accessiblecurrent
bwaVLCurrentFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. An entry in the Current Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.6.1not-accessiblecurrent
bwaVLCurrentFrequencySubsetTableIdx
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. An index of an entry in the Current Frequency subset Table. Not applicable to SU/RB with SW version 4.0 and higher.
1.3.6.1.4.1.12394.1.1.6.12.6.1.1INTEGER (1..40)read-onlycurrent
bwaVLCurrentFrequencySubsetFrequency
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLCurrentFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Current Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.6.1.2INTEGERread-onlycurrent
bwaVLCurrentFrequencySubsetFrequencyNew
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Current Frequency Subset table. (Replaces bwaVLCurrentFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.6.1.3DisplayStringread-onlycurrent
bwaVLCurrentAUOperatingFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLCurrentUOperatingFrequencyNew to support a resolution of 0.5 MHz). The operating frequency in MHz. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.7INTEGERread-onlycurrent
bwaVLAUDefinedFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLAUDefinedFrequencyNew to support a resolution of 0.5 MHz). For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.8INTEGERread-writecurrent
bwaVLCurrentSUOperatingFrequency
OBJECT-TYPE
Applicable to SU/RB only. The frequency used currently by the unit. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.9DisplayStringread-onlycurrent
bwaVLSubBandSelect
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.10
bwaVLSelectSubBandIndex
OBJECT-TYPE
Applicable to all units with SW version below 4.0 For units with SW version 4.0 and up it is applicable only for AU/BU. For SU/RB it defines only the sub-band for the Spectrum Analyzer. The ID of the sub-band used by the unit.
1.3.6.1.4.1.12394.1.1.6.12.10.1INTEGERread-writecurrent
bwaVLDFSParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.11
bwaVLDFSOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the DFS Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLDFSChannelCheckTime
OBJECT-TYPE
Applicable to AU/BU only. Defines the time the unit checks the channel for presence of radar signals and does not transmit after power up or association or after moving to a new channel due to detecting radar in the used channel. Range: 1 to 3600 (seconds).
1.3.6.1.4.1.12394.1.1.6.12.11.3INTEGERread-writecurrent
bwaVLDFSChannelAvoidancePeriod
OBJECT-TYPE
Applicable to AU/BU only. Defines the time after detecting radar signals in a channel of avoiding using the channel or adjacent channels in accordance with the bandwidth. Range: 1 to 60 (minutes).
1.3.6.1.4.1.12394.1.1.6.12.11.4INTEGERread-writecurrent
bwaVLDFSSuWaitingOption
OBJECT-TYPE
Applicable to AU/BU only. Defines whether the associated SUs should wait for this AU/BU after it stopped transmitting due to radar detection, before they starts scanning for other AUs/BUs.
1.3.6.1.4.1.12394.1.1.6.12.11.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLDFSClearRadarDetectedChannelsAfterReset
OBJECT-TYPE
Applicable to AU/BU only. Clear Radar Detected and Adjacent to Radar channels after unit reset. Returns the unit to operate in default frequency.
1.3.6.1.4.1.12394.1.1.6.12.11.6INTEGER {cancel(1), clearRadarChannels(2), na(255)}read-writecurrent
bwaVLDFSRadarDetectionChannelsTable
OBJECT-TYPE
Applicable to AU/BU only. Applicable only when DFS option is on. Displays the current channels defined in the sub-band and their radar detection status.
1.3.6.1.4.1.12394.1.1.6.12.11.7not-accessiblecurrent
bwaVLDFSRadarDetectionChannelsEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the bwaVLDFSRadarDetectionChannelsTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1not-accessiblecurrent
bwaVLDFSChannelIdx
OBJECT-TYPE
Applicable to AU/BU only. Read-only. The index of the entry in the bwaVLDFSRadarDetectionChannelsTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.1INTEGER (1..40)read-onlycurrent
bwaVLDFSChannelFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLDFSChannelFrequency New to support a resolution of 0.5 MHz). The frequency in MHz of a channel in the DFS Radar Detection Channels Table.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.2INTEGERread-onlycurrent
bwaVLDFSChannelRadarStatus
OBJECT-TYPE
Applicable to AU/BU only. The radar detection status of a channel in bwaVLDFSRadarDetectionChannelTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.3INTEGER {radarFree(1), adjacentToRadar(2), radarDetected(3)}read-onlycurrent
bwaVLDFSChannelFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. The frequency of a channel in the DFS Radar Detection Channels Table. (Replaces bwaVLDFSChannelFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.4DisplayStringread-onlycurrent
bwaVLDFSMinimumPulsesToDetect
OBJECT-TYPE
Applicable to AU/BU only. Defines the minimum number of pulses to detect a radar. Range: 1 - 100.
1.3.6.1.4.1.12394.1.1.6.12.11.8INTEGERread-writecurrent
bwaVLDFSChannelReuseParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.11.9
bwaVLDFSChannelReuseOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the DFS Channel Reuse Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.11.9.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLDFSRadarActivityAssessmentPeriod
OBJECT-TYPE
Applicable to AU/BU only. Range: 1 to 12 (Houres).
1.3.6.1.4.1.12394.1.1.6.12.11.9.2INTEGERread-writecurrent
bwaVLDFSMaximumNumberOfDetectionsInAssessmentPeriod
OBJECT-TYPE
Applicable to AU/BU only. Range: 1 to 10 (Times).
1.3.6.1.4.1.12394.1.1.6.12.11.9.3INTEGERread-writecurrent
bwaVLCountryCodeLearningBySU
OBJECT-TYPE
Applicable to AU only. Starting with 4.0 it is nor applicable for BWA 4900 and BWA PtP. Defines whether the SUs learn the country code of the AU.
1.3.6.1.4.1.12394.1.1.6.12.12INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLCurrentAUOperatingFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. The operating frequency in MHz. (Replaces bwaVLCurrentAUOperatingFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.13DisplayStringread-onlycurrent
bwaVLAUDefinedFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. (Replaces bwaVLAUDefinedFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.14DisplayStringread-writecurrent
bwaVLAutoSubBandSelect
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.15
bwaVLAutoSubBandSelectedFreqSubset
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.15.1INTEGER {setAllSelectedFreqsSubset(1), cancel(2)}read-writecurrent
bwaVLAutoSubBandFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all available sub-bands and all the frequencies in these sub-bands.
1.3.6.1.4.1.12394.1.1.6.12.15.2not-accessiblecurrent
bwaVLAutoSubBandFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1not-accessiblecurrent
bwaVLAutoSubBandFrequencySubsetBandIdx
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable Sub Band. This is the Sub Band ID of the relevant entry in the Country Dependent Parameters table. Serves also as an index of the entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.1INTEGER (1..5)read-onlycurrent
bwaVLAutoSubBandFrequencySubsetFrequencyIdx
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable frequency in the applicable Sub Band. Serves also as an index of the entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.2INTEGER (1..40)read-onlycurrent
bwaVLAutoSubBandFrequencySubsetActive
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Auto Sub Band Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.3INTEGER {active(1), notActive(2)}read-writecurrent
bwaVLAutoSubBandFrequencySubsetFrequency
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of the entry in the Auto Sub Band Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.4DisplayStringread-onlycurrent
bwaVLATPC
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.13
bwaVLAtpcOption
OBJECT-TYPE
Applicable all units. Enabling/disabling the ATPC Algorithm.
1.3.6.1.4.1.12394.1.1.6.13.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLDeltaFromMinSNRLevel
OBJECT-TYPE
Applicable AU/BU only. The Minimum SNR Level plus the value of this parameter define the maximum desired level of the average SNR at the AU/BU. If the ATPC Option is enabled, than if the received SNR is above the maximum desired level, the AU/BU will transmit Power-Down messages to the applicable SU/RB. Range: 4 to 20 (dB).
1.3.6.1.4.1.12394.1.1.6.13.2INTEGERread-writecurrent
bwaVLMinimumSNRLevel
OBJECT-TYPE
Applicable AU/BU only. Defines the minimum desired level of the average SNR at the AU/BU. Below this level, if *AtpcOption is enabled, the AU/BU will transmit ATPC Power-Up messages to the applicable SU/RB. The *MinimumSNRLevel cannot be higher than *MaximumSNRLevel. Range: 4 to 60 (dB).
1.3.6.1.4.1.12394.1.1.6.13.3INTEGERread-writecurrent
bwaVLMinimumIntervalBetweenATPCMessages
OBJECT-TYPE
Applicable AU/BU only. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
1.3.6.1.4.1.12394.1.1.6.13.4INTEGERread-writecurrent
bwaVLPowerLevelSteps
OBJECT-TYPE
Applicable AU/BU only. The step in dB that the SU/RB will use when receiving an ATPC Power-Up/Power-Down message. Range: 1 to 20 (dB).
1.3.6.1.4.1.12394.1.1.6.13.6INTEGERread-writecurrent
bwaVLCellDistanceParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.15
bwaVLCellDistanceMode
OBJECT-TYPE
Applicable AU/BU only. The selected mode of deciding on Cell Distance.
1.3.6.1.4.1.12394.1.1.6.15.1INTEGER {automatic(1), manual(2), na(255)}read-writecurrent
bwaVLFairnessFactor
OBJECT-TYPE
Applicable AU/BU only. Not applicable to BWA-PtP products for SW version below 4.0.. The percentage of the maximum distance that is taken into account in the time slot calculation. Range: 0 to 100 (Percent). A value of 0 means the minimal slot size (9 microseconds). BWA-PtP products with SW version below 4.0 return na.
1.3.6.1.4.1.12394.1.1.6.15.2INTEGER {na(255)}read-writecurrent
bwaVLMeasuredCellDistance
OBJECT-TYPE
Applicable AU/BU only. The Maximum Cell Distance as calculated by the AU/BU. Range: 0 to 54 (Kilometers).
1.3.6.1.4.1.12394.1.1.6.15.3INTEGER {below-2-Km(1)}read-onlycurrent
bwaVLUnitWithMaxDistance
OBJECT-TYPE
Applicable AU only. Not applicable to BWA-PtP units. The MAC address of the unit with the maximum distance from the AU.
1.3.6.1.4.1.12394.1.1.6.15.4MacAddressread-onlycurrent
bwaVLPerSuDistanceLearning
OBJECT-TYPE
Aplicable to AU only. Applicable only if Cell Distance Mode is set to Automatic. When disabled, all SUs in the cell will use for the ACK Timeout the computed distance of the farthest SU. When enabled, each SU will use its own computed distance
1.3.6.1.4.1.12394.1.1.6.15.5INTEGER {disable(1), enable(2)}read-writecurrent
bwaVLScanningMode
OBJECT-TYPE
Applicable to SU/RB only. The scanning mode. In cells where the DFS Option is enabled Scanning Mode is forced to Passive.
1.3.6.1.4.1.12394.1.1.6.16INTEGER {passive(1), active(2)}read-writecurrent
bwaVLAntennaGain
OBJECT-TYPE
Applicable to all units. Read-write in units where bwaVLAntennaGainChange is supported. Read-only in units where bwaVLAntennaGainChange is not supported. The net gain (including cable attenuation for detached antennas) of the antenna. Range: 0 - to Maximum EIRP defined by country code + 10 (dBi). A value of -2 (this value is configurable only in factory) means don't care. A value of -1 (this value is configurable only in factory) means that the unit will not transmit until the actual value is configured.
1.3.6.1.4.1.12394.1.1.6.17DisplayStringread-writecurrent
bwaVLSpectrumAnalysisParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.18
bwaVLSpectrumAnalysisChannelScanPeriod
OBJECT-TYPE
Applicable to all units. The period of staying on each channel for information gathering when performing Spectrum analysis. Range: 2-30 seconds.
1.3.6.1.4.1.12394.1.1.6.18.1INTEGERread-writecurrent
bwaVLSpectrumAnalysisScanCycles
OBJECT-TYPE
Applicable to all units. The number of scanning cycles when performing Spectrum Analysis. Range: 1-100.
1.3.6.1.4.1.12394.1.1.6.18.2INTEGERread-writecurrent
bwaVLAutomaticChannelSelection
OBJECT-TYPE
Applicable to AU/BU only. Defines weather the AU/BU shall choose the most noise free channel upon startup after spectrum analysis.
1.3.6.1.4.1.12394.1.1.6.18.3INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLSpectrumAnalysisActivation
OBJECT-TYPE
Applicable to all units. Activates spectrum analysis, the unit is automatically reset upon activation.
1.3.6.1.4.1.12394.1.1.6.18.4INTEGER {cancelOperation(1), activateNow(2)}read-writecurrent
bwaVLSpectrumAnalysisStatus
OBJECT-TYPE
Applicable to all units. Defines weather the unit is currently under performing a spectrum analysis process.
1.3.6.1.4.1.12394.1.1.6.18.5INTEGER {inactive(1), currentlyActive(2)}read-onlycurrent
bwaVLResetSpectrumCounters
OBJECT-TYPE
Applicable to all units. Resets the spectrum analysis counters.
1.3.6.1.4.1.12394.1.1.6.18.6INTEGER {cancelOperation(1), resetCounters(2)}read-writecurrent
bwaVLSpectrumAnalysisInformationTable
OBJECT-TYPE
Applicable to all units. The spectrum analysis information table.
1.3.6.1.4.1.12394.1.1.6.18.7not-accessiblecurrent
bwaVLSpectrumAnalysisInformationEntry
OBJECT-TYPE
Applicable to all units. The spectrum analysis information table entry.
1.3.6.1.4.1.12394.1.1.6.18.7.1not-accessiblecurrent
bwaVLSpectrumAnalysisInformationTableIdx
OBJECT-TYPE
Applicable to all units. A read only table index for a Spectrum Analysis Information entry in the Spectrum Analysis Information Table.
1.3.6.1.4.1.12394.1.1.6.18.7.1.1INTEGER (1..60)read-onlycurrent
bwaVLSpectrumAnalysisInformationChannel
OBJECT-TYPE
Applicable to all units. The channels in the Spectrum Analysis Information Table. If the unit is currently under spectrum analysis the channels would be those on which the analysis is currently performed. If the unit is in normal mode the channels would be the those on which the last analysis was performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.2DisplayStringread-onlycurrent
bwaVLSpectrumAnalysisInformationSignalCount
OBJECT-TYPE
Applicable to all units. The number of signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.3INTEGERread-onlycurrent
bwaVLSpectrumAnalysisInformationSignalSNR
OBJECT-TYPE
Applicable to all units. The approximate SNR of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the SNR would be of the analysis that is currently performed. If the unit is in normal mode the SNR would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.4INTEGERread-onlycurrent
bwaVLSpectrumAnalysisInformationSignalWidth
OBJECT-TYPE
Applicable to all units. The average width of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the width would be of the analysis that is currently performed. If the unit is in normal mode the width would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.5INTEGERread-onlycurrent
bwaVLSpectrumAnalysisInformationOFDMFrames
OBJECT-TYPE
Applicable to all units. The number of OFDM frames detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.6INTEGERread-onlycurrent
bwaVLMaxNumOfAssociationsLimit
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. Shows the limit for the number of SUs that can be associated with the AU. For AU-BS, AU-SA if Data Encryption is enabled, the upper limit is 124, otherwise it is 512. For AUS-BS, AUS-SA with SW version 4.0 and higher the upper limit is 8 or 25 (via licensing). For AUS-BS, AUS-SA with SW version below 4.0 the upper limit is 5. BWA-PtP products return 65535.
1.3.6.1.4.1.12394.1.1.6.19INTEGERread-onlycurrent
bwaVLDisassociate
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.20
bwaVLDisassociateAllSUs
OBJECT-TYPE
Applicable to AU only. The AU shall disassociate all its associated units.
1.3.6.1.4.1.12394.1.1.6.20.1INTEGER {cancelOperation(1), disassociateAllSUs(2)}read-writecurrent
bwaVLDisassociateSuByMacAddress
OBJECT-TYPE
Applicable to AU only. The AU shall disassociate the SU with the configured MAC address.
1.3.6.1.4.1.12394.1.1.6.20.2MacAddressread-writecurrent
bwaVLTxControl
OBJECT-TYPE
Applicable to AU/BU only. Tx Control of the AU/BU. Starting with version 4.0 it is run-time. For SW version below 4.0 the unit reset itself. If set to ethernetStatusControl, the unit will not transmit if the Ethernet link is down. This parameter can be configured only via the ethernet port.
1.3.6.1.4.1.12394.1.1.6.21INTEGER {on(1), off(2)}read-writecurrent
bwaVLLostBeaconsWatchdogThreshold
OBJECT-TYPE
Applicable to AU/BU only. The number of unsuccessful consecutive transmissions beacons before Internal refresh is performed. 0 means that the lost beacons watchdog is not used and internal refresh is not performed.
1.3.6.1.4.1.12394.1.1.6.22INTEGER (0 | 100..1000)read-writecurrent
bwaVLTransmitPower
OBJECT-TYPE
Applicable to all units with SW version 4.0 and higher. The uniform transmit power for all modulation levels. For a specific modulation level the effective transmit power (bwaVLTxPower) is the minimum between the uniform transmit power and the maximum transmit power for that modulation level.
1.3.6.1.4.1.12394.1.1.6.23INTEGERread-writecurrent
bwaVLMaximumTxPower
OBJECT-TYPE
Applicable to only SU/RB with SW version 4.0 and higher. The Maximum Transmit Power for all modulation levels. The Maximum Transmit Power for a specific modulation level is the minimum between this parameter and the hardware limitation for that modulation level
1.3.6.1.4.1.12394.1.1.6.24INTEGERread-writecurrent
bwaVLCountryCodeParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.25
bwaLCountryCodeReApply
OBJECT-TYPE
Applicable to all units. Re-apply country code parameters.
1.3.6.1.4.1.12394.1.1.6.25.1INTEGER {reapply(1), cancel(2), na(255)}read-writecurrent
bwaVLServiceParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7
bwaVLMaxDelay
OBJECT-TYPE
Applicable to SU only. Not applicable to BWA-PtP products. The maximal time packets may be delayed by the CIR\MIR mechanism. Above the configured maximal period the packets are discarded. Range: 300 to 10000 milliseconds. BWA-PtP products return 65535.
1.3.6.1.4.1.12394.1.1.7.6INTEGERread-writecurrent
bwaVLMaxBurstDuration
OBJECT-TYPE
Applicable to AU and SU. Not applicable to BWA-PtP products. The maximum time during which inactivity bonus time can be accumulated for future burst transmissions. Range: 0 to 2000 milliseconds. BWA-PtP products return 65535
1.3.6.1.4.1.12394.1.1.7.7INTEGERread-writecurrent
bwaVLGracefulDegradationLimit
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. The maximum limit for activating the graceful degradation algorithm. Range: 0 to 70% rate of the CIR. BWA-PtP products return 255.
1.3.6.1.4.1.12394.1.1.7.8INTEGERread-writecurrent
bwaVLMirOnlyOption
OBJECT-TYPE
Applicable to AU only. Not applicable to BWA-PtP products. When bwaMirOnly is enabled, it overrides the CIR/MIR algorithm for determining actual information rate and forces the algorithm to operate with MIR parameter settings only. When enabled, the Graceful Degradation algorithm is disabled.
1.3.6.1.4.1.12394.1.1.7.9INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLTrafficPrioritization
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10
bwaVLTrafficPriVLAN
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.1
bwaVLVLANPriorityThreshold
OBJECT-TYPE
Applicable to all units. If the VLAN Priority's value of the frame is less than or equal to this threshold the frame will get LOW priority, otherwise the frame will get HIGH priority. Untagged frames will get LOW priority
1.3.6.1.4.1.12394.1.1.7.10.1.1INTEGER (1..7)read-writecurrent
bwaVLTrafficPriIPToS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.2
bwaVLToSPrioritizationOption
OBJECT-TYPE
Applicable to all units. Disable/Enable IP ToS prioritization and choose the interpretation of the IP ToS field from IP header. ipPrecedence(2): The IP ToS field is defined by RFC791. In this case the prioritization will be done using the Precedence sub-field of IP ToS. This sub-field has 3 bits, so it can be between 0 and 7. dSCP(3): The IP ToS field is defined by RFC2474. In this case the prioritization will be done using the DSCP sub-field. The size of the sub-field is 6 bits, so the range is 0 to 63.
1.3.6.1.4.1.12394.1.1.7.10.2.1INTEGER {disable(1), ipPrecedence(2), dSCP(3)}read-writecurrent
bwaVLIPPrecedenceThreshold
OBJECT-TYPE
Applicable to all units. The threshold of Precedence sub-field of IP ToS field from IP Header (RFC791) to be used when the ToS Prioritization Option is set to IP Precedence. If the Precedence sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.2.2INTEGER (0..7)read-writecurrent
bwaVLIPDSCPThreshold
OBJECT-TYPE
Applicable to all units. The threshold of DSCP sub-field of IP ToS field from IP Header (RFC2474) to be used when ToS Prioritization Option is set to DSCP. If the DSCP sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.2.3INTEGER (0..63)read-writecurrent
bwaVLTrafficPriUdpTcpPortRange
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3
bwaVLUdpTcpPortRangePrioritizationOption
OBJECT-TYPE
Applicable to all units. Disable/Enable Prioritization using UDP and/or TCP Port Ranges. udpOnly(2) : prioritization will be done only for UDP packets tcpOnly(3) : prioritization will be done only for TCP packets udpANDtcp(4): prioritization will be done for UDP and TCP packets
1.3.6.1.4.1.12394.1.1.7.10.3.1INTEGER {disable(1), udpOnly(2), tcpOnly(3), udpANDtcp(4)}read-writecurrent
bwaVLUdpPortRangeConfig
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3.2
bwaVLUdpPortPriRTPRTCP
OBJECT-TYPE
Applicale to all units. RTP/RTCP ports prioritization option for UDP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port ) with destination port in the defined port ranges will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.3.2.1INTEGER {rtpANDrtcp(1), rtpOnly(2)}read-writecurrent
bwaVLUdpPortRangeNum
OBJECT-TYPE
Applicable to all units. The number of entries in the UDP Port Range Table
1.3.6.1.4.1.12394.1.1.7.10.3.2.2INTEGERread-onlycurrent
bwaVLUdpPortRangeTable
OBJECT-TYPE
Applicable to all units. A table of UDP port ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
1.3.6.1.4.1.12394.1.1.7.10.3.2.3not-accessiblecurrent
bwaVLUdpPortRangeEntry
OBJECT-TYPE
Applicable to all units. A UDP Port Ranges Table entry.
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1not-accessiblecurrent
bwaVLUdpPortRangeStart
OBJECT-TYPE
Applicable to all units. Start port of an UDP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.1INTEGER (0..65535)read-onlycurrent
bwaVLUdpPortRangeEnd
OBJECT-TYPE
Applicable to all units. End port of an UDP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.2INTEGER (0..65535)read-onlycurrent
bwaVLUdpPortRangeIdx
OBJECT-TYPE
Applicable to all units. UDP Port Range Entry's index
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.3INTEGER (1..64)read-onlycurrent
bwaVLUdpPortRangeAdd
OBJECT-TYPE
Applicable to all units. Add port range(s) to UDP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can add several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.2.4DisplayString (SIZE(0..250))read-writecurrent
bwaVLUdpPortRangeDelete
OBJECT-TYPE
Applicable to all units. Delete port range(s) from UDP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can delete several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.2.5DisplayString (SIZE(0..250))read-writecurrent
bwaVLUdpPortRangeDeleteAll
OBJECT-TYPE
Applicable to all units. Delete all entries form UDP Port Ranges Table. Get operation will return 1
1.3.6.1.4.1.12394.1.1.7.10.3.2.6INTEGER {deleteAll(1), cancelOperation(2)}read-writecurrent
bwaVLTcpPortRangeConfig
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3.3
bwaVLTcpPortPriRTPRTCP
OBJECT-TYPE
Applicable to all units. RTP/RTCP ports prioritization option for TCP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port )
1.3.6.1.4.1.12394.1.1.7.10.3.3.1INTEGER {rtpANDrtcp(1), rtpOnly(2)}read-writecurrent
bwaVLTcpPortRangeNum
OBJECT-TYPE
Applicable to all units. The number of entries in the TCP Port Range Table
1.3.6.1.4.1.12394.1.1.7.10.3.3.2INTEGERread-onlycurrent
bwaVLTcpPortRangeTable
OBJECT-TYPE
Table of TCP Port Ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
1.3.6.1.4.1.12394.1.1.7.10.3.3.3not-accessiblecurrent
bwaVLTcpPortRangeEntry
OBJECT-TYPE
Applicable to all units. A TCP Port Ranges Table entry.
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1not-accessiblecurrent
bwaVLTcpPortRangeStart
OBJECT-TYPE
Applicable to all units. Start port of a TCP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.1INTEGER (0..65535)read-onlycurrent
bwaVLTcpPortRangeEnd
OBJECT-TYPE
Applicable to all units. End port of a TCP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.2INTEGER (0..65535)read-onlycurrent
bwaVLTcpPortRangeIdx
OBJECT-TYPE
Applicable to all units. TCP Port Range Entry's index
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.3INTEGER (1..64)read-onlycurrent
bwaVLTcpPortRangeAdd
OBJECT-TYPE
Applicable to all units. Add port range(s) to TCP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can add several ranges using comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.3.4DisplayString (SIZE(0..250))read-writecurrent
bwaVLTcpPortRangeDelete
OBJECT-TYPE
Applicable to all units. Delete port range(s) from TCP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can delete several ranges using comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.3.5DisplayString (SIZE(0..250))read-writecurrent
bwaVLTcpPortRangeDeleteAll
OBJECT-TYPE
Applicable to all units. Delete all entries form TCP Port Ranges Table Get operation will return 1
1.3.6.1.4.1.12394.1.1.7.10.3.3.6INTEGER {deleteAll(1), cancelOperation(2)}read-writecurrent
bwaVLWirelessLinkPrioritization
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.4
bwaVLWirelessLinkPrioritizationOption
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Enable/disable the traffic prioritization over the Wireless Link
1.3.6.1.4.1.12394.1.1.7.10.4.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLlowPriorityAIFS
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Define the AIFS (Arbitration Inter-frame Space) that will be used for transmitting Low Priority Traffic
1.3.6.1.4.1.12394.1.1.7.10.4.2INTEGER (3..254)read-writecurrent
bwaVLHWRetriesHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has High Priority
1.3.6.1.4.1.12394.1.1.7.10.4.3INTEGER (0..14)read-writecurrent
bwaVLHWRetriesLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has Low Priority
1.3.6.1.4.1.12394.1.1.7.10.4.4INTEGER (0..14)read-writecurrent
bwaVLAUBurstDurationHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with High Priority packets. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.5INTEGER (0..40)read-writecurrent
bwaVLAUBurstDurationLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with Low Priority packets. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.6INTEGER (0..40)read-writecurrent
bwaVLSUBurstDurationHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU and the SUs/RB will learn it form AU/BU. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.7INTEGER (0..40)read-writecurrent
bwaVLSUBurstDurationLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU/BU and the SUs/RB will learn it from AU/BU. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.8INTEGER (0..40)read-writecurrent
bwaVLDrap
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.11
bwaVLDrapSupport
OBJECT-TYPE
Applicable to AU. Not applicable to BWA PtP products. Disable/Enable the DRAP feature
1.3.6.1.4.1.12394.1.1.7.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLDrapUdpPort
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The UDP port used for the DRAP server
1.3.6.1.4.1.12394.1.1.7.11.2INTEGER (8000..8200)read-writecurrent
bwaVLDrapMaxNumberOfVoiceCalls
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The maximum number of voice calls that can be supported by the AU
1.3.6.1.4.1.12394.1.1.7.11.3INTEGER (0..255)read-writecurrent
bwaVLDrapTTL
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The maximum time between two allocation requests
1.3.6.1.4.1.12394.1.1.7.11.4INTEGER (1..255)read-writecurrent
bwaVLDrapNoOfActiveVoiceCalls
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The current total number of active voice calls.
1.3.6.1.4.1.12394.1.1.7.11.5INTEGERread-onlycurrent
bwaVLLowPriorityTrafficMinimumPercent
OBJECT-TYPE
The minimum percent of the traffic rate that is allocated to the low priority traffic
1.3.6.1.4.1.12394.1.1.7.12INTEGER (0..100)read-writecurrent
bwaVLMIRThresholdPercent
OBJECT-TYPE
Applicable to AU only. MIR Threshold Percent
1.3.6.1.4.1.12394.1.1.7.14INTEGER (0..100)read-writecurrent
bwaVLUserFilterParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.8
bwaVLUserFilterOption
OBJECT-TYPE
Applicable to SU/RB only. Defines user-filtering options. disable: No filtering. iPOnly: Only IP protocol frames pass. userDefinedAddrOnly: Only ip frames to/from user defined IP addresses pass. pPPoE Only: Only PPPoE frames pass.
1.3.6.1.4.1.12394.1.1.8.1INTEGER {disable(1), ipOnly(2), userDefinedAddrOnly(3), pPPoEOnly(4), na(255)}read-writecurrent
bwaVLIpFilterTable
OBJECT-TYPE
Applicable to SU/RB only. An IP Filter Table of up to 8 user defined addresses, or address groups, to be used if the selected User Filtering option is userDefinedAddrOnly.
1.3.6.1.4.1.12394.1.1.8.2not-accessiblecurrent
bwaVLIpFilterEntry
OBJECT-TYPE
Applicable to SU/RB only. An IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1not-accessiblecurrent
bwaVLIpID
OBJECT-TYPE
Applicable to SU/RB only. An IP address of an IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1.1IpAddressread-writecurrent
bwaVLMaskID
OBJECT-TYPE
Applicable to SU/RB only. An IP Mask of an IP Filter Table entry. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group.
1.3.6.1.4.1.12394.1.1.8.2.1.2IpAddressread-writecurrent
bwaVLIpFilterRange
OBJECT-TYPE
Applicable to SU/RB only. An addresses range for the IP Filter Table entry. The first address in the range is the IP address. O means that the range is not used. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group. Range: 0 to 255.
1.3.6.1.4.1.12394.1.1.8.2.1.3INTEGERread-writecurrent
bwaVLIpFilterIdx
OBJECT-TYPE
Applicable to SU/RB only. A table index for the IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1.4INTEGER (1..8)read-onlycurrent
bwaVLDeleteOneUserFilter
OBJECT-TYPE
Applicable to SU/RB only. Deletes a single selected entry from the IP Filter Table.
1.3.6.1.4.1.12394.1.1.8.3INTEGER {deletefirstEntry(1), deletesecondEntry(2), deletethirdEntry(3), deletefourthEntry(4), deletefifthEntry(5), deletesixthEntry(6), deleteseventhEntry(7), deleteeighthEntry(8), cancelOperation(9), na(255)}read-writecurrent
bwaVLDeleteAllUserFilters
OBJECT-TYPE
Applicable to SU/RB only. Deletes all entries from the IP Filter Table.
1.3.6.1.4.1.12394.1.1.8.4INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
bwaVLDHCPUnicastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the unicast DHCP messages, overriding the IP Filtering option.
1.3.6.1.4.1.12394.1.1.8.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLSecurityParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.9
bwaVLAuthenticationAlgorithm
OBJECT-TYPE
Applicable to all units. Enables/disables the authentication encryption option. openSystem: Authentication messages are not encrypted. sharedKey : Authentication messages are encrypted
1.3.6.1.4.1.12394.1.1.9.1INTEGER {openSystem(1), sharedKey(2)}read-writecurrent
bwaVLSUDefaultKeyID
OBJECT-TYPE
Applicable to SU/RB only. The key to be used for encryption of authentication messages and/or data. Range: 1 to 4.
1.3.6.1.4.1.12394.1.1.9.2INTEGERread-writecurrent
bwaVLDataEncryptionOption
OBJECT-TYPE
Applicable to all units. Enables/disables the data encryption option.
1.3.6.1.4.1.12394.1.1.9.3INTEGER {disable(1), enable(2)}read-writecurrent
bwaVLAUDefaultMulticastKeyID
OBJECT-TYPE
Applicable to AU/BU only. The key to be used for encryption of multicasts and broadcasts.
1.3.6.1.4.1.12394.1.1.9.4INTEGERread-writecurrent
bwaVLSecurityMode
OBJECT-TYPE
Applicable to all units. The fips197 option is applicable only to units with a license to use FIPS 197 algorithm. The encryption algorithm to be used for authentication messages and/or data encryption.
1.3.6.1.4.1.12394.1.1.9.5INTEGER {wep(1), aesOCB(2), fips197(3)}read-writecurrent
bwaVLAuthenticationPromiscuousMode
OBJECT-TYPE
Applicable to AU/BU only. Enables/disable the promiscuous mode allowing authentication of and communication with all SUs/RB regardless of their security parameters.
1.3.6.1.4.1.12394.1.1.9.6INTEGER {disable(1), enable(2)}read-writecurrent
bwaVLKey1
OBJECT-TYPE
Applicable to all units. Key number 1. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.7DisplayString (SIZE(32))read-writecurrent
bwaVLKey2
OBJECT-TYPE
Applicable to all units. Key number 2. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.8DisplayString (SIZE(32))read-writecurrent
bwaVLKey3
OBJECT-TYPE
Applicable to all units. Key number 3. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.9DisplayString (SIZE(32))read-writecurrent
bwaVLKey4
OBJECT-TYPE
Applicable to all units. Key number 4. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.10DisplayString (SIZE(32))read-writecurrent
bwaVLSecurityModeSupport
OBJECT-TYPE
Applicable to all units. Returns types of encryption that are supported. 0 - no encryption 1 - WEP 2 - AES OCB 3 - WEP and AES OCB 4 - FIPS-197 5 - FIPS-197 and WEP 6 - FIPS-197 and AES OCB 7 - FIPS-197, AES OCB and WEP
1.3.6.1.4.1.12394.1.1.9.12INTEGER (0..7)read-onlycurrent
bwaVLPerformanceParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10
bwaVLRTSThreshold
OBJECT-TYPE
Applicable to SU and AU. Not applicable to BWA-PtP products. The minimum frame size that requires an RTS/CTS handshake. Range: For units bearing SW version 3.0 and above: 20 to 3400 bytes, for previous SW versions 20 to 1600 bytes. BWA-PtP products return 65535.
1.3.6.1.4.1.12394.1.1.10.1INTEGERread-writecurrent
bwaVLMinContentionWindow
OBJECT-TYPE
Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BWA PtP products, for previous SW versions not applicable to BWA PtP products. The initial value to be used by the contention window calculation algorithm. Value must be 0 or power of 2 minus 1 (7,15,31...). Range: 0 to 1023, excluding 1 and 3. BWA-PtP products with SW version below 4.0 return 65535.
1.3.6.1.4.1.12394.1.1.10.3INTEGERread-writecurrent
bwaVLMaxContentionWindow
OBJECT-TYPE
Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BWA PtP products, for previous SW versions not applicable to BWA PtP products. The maximum value to be used by the contention window calculation algorithm. Value must be power of 2 minus 1 (7,15,31...) Range: 7 to 1023.
1.3.6.1.4.1.12394.1.1.10.4INTEGERread-writecurrent
bwaVLMaximumModulationLevel
OBJECT-TYPE
Applicable to all units. If the Adaptive Modulation algorithm is enabled, it sets the Maximum Modulation Level to be used. If The Modulation algorithm is disabled, it sets the Fixed Modulation Level to be used. The range is 1 to 8. 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.10.5INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-writecurrent
bwaVLMulticastModulationLevel
OBJECT-TYPE
Applicable to AU/BU only. The modulation level for multicast and broadcast data frames. The range is 1 to 8. 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.10.6INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-writecurrent
bwaVLAvgSNRMemoryFactor
OBJECT-TYPE
Applicable to all units. The weight of history in average SNR calculation. The higher is the value, the higher is the weight of history. Range: -1 (Disregard History) to 32.
1.3.6.1.4.1.12394.1.1.10.7DisplayStringread-writecurrent
bwaVLHardwareRetries
OBJECT-TYPE
Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. The maximum number of trials to transmit an unacknowledged frame in each Hardware Retrial phase. Range : 1 to 14.
1.3.6.1.4.1.12394.1.1.10.8INTEGERread-writecurrent
bwaVLAdaptiveModulationParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.9
bwaVLAdaptiveModulationAlgorithmOption
OBJECT-TYPE
Applicable to all units. Enables/disables the adaptive modulation level decision mechanism.
1.3.6.1.4.1.12394.1.1.10.9.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLSoftwareRetrySupport
OBJECT-TYPE
Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The status of the Software Retry mechanism. Enabled when the Adaptive Modulation algorithm is enabled and the Burst Mode Option is disabled. Otherwise it is disabled.
1.3.6.1.4.1.12394.1.1.10.9.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLNumOfSoftwareRetries
OBJECT-TYPE
Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The maximum number of times to use the Software Retry mechanism when it is enabled.
1.3.6.1.4.1.12394.1.1.10.9.3INTEGER {na(255)}read-writecurrent
bwaVLMinIntervalBetweenAdaptiveModulationAlgorithmMessages
OBJECT-TYPE
Applicable all units. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
1.3.6.1.4.1.12394.1.1.10.9.4INTEGERread-writecurrent
bwaVLAdaptiveModulationDecisionThresholds
OBJECT-TYPE
Applicable to all units. Defines the setting of thresholds for the rate decision algorithm. high (2) should typically be used when the SNR is lower than 13dB.
1.3.6.1.4.1.12394.1.1.10.9.5INTEGER {normal(1), high(2), na(255)}read-writecurrent
bwaVLBurstMode
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.10
bwaVLBurstModeOption
OBJECT-TYPE
Applicable to all units. Applicable only if Burst Mode Option is supported by country specific parameters of the Sub Band. Not applicable if Wireless Link Prioritization is enabled. Enables/disable burst mode operation. In SU/RB with HW Revision B or lower blocked(3) value is returned when Security Mode is Wep , Data Encryption Option is Enabled and Burst option is Enabled. In AU/BU with HW Revision B or lower blocked(3) value is returned when Dfs Option is Enabled and Burst mode is enabled.
1.3.6.1.4.1.12394.1.1.10.10.1INTEGER {disable(1), enable(2), blocked(3), na(255)}read-writecurrent
bwaVLBurstInterval
OBJECT-TYPE
Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. Burst mode interval in milliseconds. Range: 1 to the maximum value as defined in the country specific parameters of the Sub Band (milliseconds).
1.3.6.1.4.1.12394.1.1.10.10.2INTEGERread-writecurrent
bwaVLConcatenationParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.11
bwaVLConcatenationOption
OBJECT-TYPE
Applicable to all units. Defines the Concatenation option.
1.3.6.1.4.1.12394.1.1.10.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
bwaVLConcatenationMaximumNumberOfFrames
OBJECT-TYPE
Applicable to all units with SW version 3.X . Not applicable for version 4.0 and higher. Defines the maximum numbers of frames that can be concatenated. Range:2 to 8 (frames).
1.3.6.1.4.1.12394.1.1.10.11.2INTEGER (2..8)read-writecurrent
bwaVLConcatenationMaxFrameSize
OBJECT-TYPE
Applicable to all units. Defines the maximum size of a concatenated frame. Range: 256 to 2200 (bytes) for BWA PtP products BU/RB14 BU/RB28, or for AU/SU with HW revision A or B. 256 to 4032 (bytes) for AU/SU with HW Revision C or higher and BWA PtP products BU/RB100.
1.3.6.1.4.1.12394.1.1.10.11.3INTEGERread-writecurrent
bwaVLSiteSurvey
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11
bwaVLAverageReceiveSNR
OBJECT-TYPE
Applicable to SU/RB only. The average Signal to Noise Ratio of received frames.
1.3.6.1.4.1.12394.1.1.11.1INTEGERread-onlycurrent
bwaVLTrafficStatistics
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2
bwaVLResetTrafficCounters
OBJECT-TYPE
Applicable to all units. Resets the traffic counters.
1.3.6.1.4.1.12394.1.1.11.2.1INTEGER {reset(1), cancel(2)}read-writecurrent
bwaVLEthCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.2
bwaVLTotalRxFramesViaEthernet
OBJECT-TYPE
Applicable to all units. Total number of frames received via the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.2.1Counter32read-onlycurrent
bwaVLTxWirelessToEthernet
OBJECT-TYPE
Applicable to all units. Total number of frames transmitted to the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.2.2Counter32read-onlycurrent
bwaVLWirelessLinkCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3
bwaVLTxFramesToWireless
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3.1
bwaVLAUBeaconsToWireless
OBJECT-TYPE
Applicable to AU/BU only. The number of beacons transmitted to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.1.1Counter32read-onlycurrent
bwaVLDataAndOtherMngFramesToWireless
OBJECT-TYPE
Applicable to AU/BU only. The number of data and management frames transmitted to the wireless media. The count includes one count for each data frame transmitted successfully (excluding retransmissions).
1.3.6.1.4.1.12394.1.1.11.2.3.1.3Counter32read-onlycurrent
bwaVLTotalTxFramesToWireless
OBJECT-TYPE
Applicable to all units. The number of frames transmitted to the wireless media. The count includes one count for each data frame that was transmitted successfully (excluding retransmissions), and also the number of transmitted control and management frames, including beacons.
1.3.6.1.4.1.12394.1.1.11.2.3.1.4Counter32read-onlycurrent
bwaVLTotalTransmittedUnicasts
OBJECT-TYPE
Applicable to AU/BU only. The total number of unicast frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.5Counter32read-onlycurrent
bwaVLTotalTransmittedConcatenatedFramesDouble
OBJECT-TYPE
Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.6Counter32read-onlycurrent
bwaVLTotalTransmittedConcatenatedFramesSingle
OBJECT-TYPE
Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.7Counter32read-onlycurrent
bwaVLTotalTransmittedConcatenatedFramesMore
OBJECT-TYPE
Applicable to all products. The total number of concatenated frames with more then two frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.8Counter32read-onlycurrent
bwaVLTotalRxFramesFromWireless
OBJECT-TYPE
Applicable to all units. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU/BU. The count does not include frames that were discarded internally, bad frames and duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.2Counter32read-onlycurrent
bwaVLTotalRetransmittedFrames
OBJECT-TYPE
Applicable to all units. The total number of retransmissions of data frames (counts all unsuccessful transmissions/retransmissions).
1.3.6.1.4.1.12394.1.1.11.2.3.3Counter32read-onlycurrent
bwaVLFramesDropped
OBJECT-TYPE
Applicable to all units. The number of dropped frames. The frames that were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged..
1.3.6.1.4.1.12394.1.1.11.2.3.4Counter32read-onlycurrent
bwaVLDataFramesSubmittedToBridge
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3.5
bwaVLFramesSubmittedViaHighQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the High priority queue. for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.1Counter32read-onlycurrent
bwaVLFramesSubmittedViaMidQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the Mid priority queue for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.2Counter32read-onlycurrent
bwaVLFramesSubmittedViaLowQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the Low priority queue for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.3Counter32read-onlycurrent
bwaVLTotalNoOfDataFramesSubmitted
OBJECT-TYPE
Applicable to all units. The total number of data frames submitted to the internal bridge for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.4Counter32read-onlycurrent
bwaVLTotalRecievedDataFrames
OBJECT-TYPE
Applicable to all units. The total number of data frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.6Counter32read-onlycurrent
bwaVLRecievedBadFrames
OBJECT-TYPE
Applicable to all units. The number of frames received from the wireless media with errors (CRC errors).
1.3.6.1.4.1.12394.1.1.11.2.3.7Counter32read-onlycurrent
bwaVLNoOfDuplicateFramesDiscarded
OBJECT-TYPE
Applicable to all units. The number of frames discarded due to receiving multiple copies.
1.3.6.1.4.1.12394.1.1.11.2.3.8Counter32read-onlycurrent
bwaVLNoOfInternallyDiscardedMirCir
OBJECT-TYPE
Applicable to all units. The number of data frames received from the Ethernet port that were discarded by the MIR/CIR mechanism either to avoid exceeding the maximum allowed information rate, or when the wireless link conditions do not enable reaching the allowed rate.
1.3.6.1.4.1.12394.1.1.11.2.3.9Counter32read-onlycurrent
bwaVLTotalRxConcatenatedFramesDouble
OBJECT-TYPE
Applicable to all units. The total number of double concatenated frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.10Counter32read-onlycurrent
bwaVLTotalRxConcatenatedFramesSingle
OBJECT-TYPE
Applicable to all units. The total number of data fast frames single concatenated frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.11Counter32read-onlycurrent
bwaVLTotalRxConcatenatedFramesMore
OBJECT-TYPE
Applicable to all units. The total number of data fast frames concatenated with more then two frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.12Counter32read-onlycurrent
bwaVLWirelessLinkEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4
bwaVLTxEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4.1
bwaVLDroppedFrameEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were dropped because they were retransmitted to the maximum allowed number of retransmissions without being acknowledged.
1.3.6.1.4.1.12394.1.1.11.2.4.1.1Counter32read-onlycurrent
bwaVLFramesDelayedDueToSwRetry
OBJECT-TYPE
Applicable to all units. Not applicable for units with SW Version 3.0 and higher. The number of frames that were delayed because the SW retry algorithm was activated on a previous frame designated for the same recipient.
1.3.6.1.4.1.12394.1.1.11.2.4.1.2Counter32read-onlycurrent
bwaVLUnderrunEvents
OBJECT-TYPE
Applicable to all units. The number of frames whose transmission was aborted because the rate of submitting frames for transmission exceeded the available transmission capability.
1.3.6.1.4.1.12394.1.1.11.2.4.1.3Counter32read-onlycurrent
bwaVLOthersTxEvents
OBJECT-TYPE
Applicable to all units. The number of Tx events due to problems other than those of the other Tx Events counters.
1.3.6.1.4.1.12394.1.1.11.2.4.1.4Counter32read-onlycurrent
bwaVLTotalTxEvents
OBJECT-TYPE
Applicable to all units. The total number of Tx special events.
1.3.6.1.4.1.12394.1.1.11.2.4.1.5Counter32read-onlycurrent
bwaVLRxEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4.2
bwaVLPhyErrors
OBJECT-TYPE
Applicable to all units, only when DFS is enabled. The number of unidentified signals.
1.3.6.1.4.1.12394.1.1.11.2.4.2.1Counter32read-onlycurrent
bwaVLCRCErrors
OBJECT-TYPE
Applicable to all units. The number of frames received from the wireless media containing CRC errors.
1.3.6.1.4.1.12394.1.1.11.2.4.2.2Counter32read-onlycurrent
bwaVLOverrunEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were discarded because the receive rate exceeded the processing capability or the capacity of the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.4.2.3Counter32read-onlycurrent
bwaVLRxDecryptEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were not received properly due to a problem in the data decryption mechanism.
1.3.6.1.4.1.12394.1.1.11.2.4.2.4Counter32read-onlycurrent
bwaVLTotalRxEvents
OBJECT-TYPE
Applicable to all units. The total number of Rx special events.
1.3.6.1.4.1.12394.1.1.11.2.4.2.5Counter32read-onlycurrent
bwaVLPerModulationLevelCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.5
bwaVLResetPerModulationLevelCounters
OBJECT-TYPE
Applicable to all units. Resets the per-Modulation Level counters .
1.3.6.1.4.1.12394.1.1.11.2.5.1INTEGER {resetCounters(1), cancel(2)}read-writecurrent
bwaVLSUPerModulationLevelCountersTable
OBJECT-TYPE
Applicable to SU/RB. Per Rate Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2not-accessiblecurrent
bwaVLSUPerModulationLevelCountersEntry
OBJECT-TYPE
Applicable to SU/RB. An entry in the Per modulation Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1not-accessiblecurrent
bwaVLSUPerModulationLevelCountersTableIdx
OBJECT-TYPE
Applicable to SU/RB. An index of an entry in the Per modulation level Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.1INTEGER (1..8)read-onlycurrent
bwaVLSUPerModulationLevelCountersApplicableModLevel
OBJECT-TYPE
Applicable to SU/RB. The applicable modulation level of the entry in the Per modulation level Counters table. Modulation Level 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.2INTEGER {modLevel-1(1), modLevel-2(2), modLevel-3(3), modLevel-4(4), modLevel-5(5), modLevel-6(6), modLevel-7(7), modLevel-8(8)}read-onlycurrent
bwaVLSUPerModulationLevelCountersTxSuccess
OBJECT-TYPE
Applicable to SU/RB. The total number of successfully transmitted unicasts at the applicable modulation level.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.3Counter32read-onlycurrent
bwaVLSUPerModulationLevelCountersTxFailed
OBJECT-TYPE
Applicable to SU/RB. The total number of dropped frames at the applicable Modulation Level.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.4Counter32read-onlycurrent
bwaVLAverageModulationLevel
OBJECT-TYPE
Applicable to SU/RB. The average modulation level for successful transmission (rounded to nearest integer) since last reset of the Per Modulation Level counters. Range: 1 to 8.
1.3.6.1.4.1.12394.1.1.11.2.5.3INTEGERread-onlycurrent
bwaVLMacAddressDatabase
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.5
bwaVLAUMacAddressDatabase
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.5.1
bwaVLAUAdbResetAllModulationLevelCounters
OBJECT-TYPE
Applicable to AU/BU only. To reset all the counters for all SUs/RB in the MAC Address Database.
1.3.6.1.4.1.12394.1.1.11.5.1.1INTEGER {reset(1), cancel(2)}read-writecurrent
bwaVLAUAdbTable
OBJECT-TYPE
Applicable to AU/BU only. AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2not-accessiblecurrent
bwaVLAUAdbEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1not-accessiblecurrent
bwaVLAdbIndex
OBJECT-TYPE
Applicable to AU/BU only. The index of an entry in the AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.1INTEGER (1..512)read-onlycurrent
bwaVLAdbMacAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC Address of an SU/RB entry in the MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.2MacAddressread-onlycurrent
bwaVLAdbStatus
OBJECT-TYPE
Applicable to AU/BU only. The status of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.3INTEGER {associated(1), authenticated(2), notAuthenticated(3)}read-onlycurrent
bwaVLAdbSwVersion
OBJECT-TYPE
Applicable to AU/BU only. The SW version of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.4DisplayStringread-onlycurrent
bwaVLAdbSNR
OBJECT-TYPE
Applicable to AU/BU only. The average Signal to Noise Ratio in dB of frames received by the AU/BU from the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.5INTEGERread-onlycurrent
bwaVLAdbMaxModulationLevel
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the Maximum Modulation Level parameter. Modulation Level 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.6INTEGER {modLevel-1(1), modLevel-2(2), modLevel-3(3), modLevel-4(4), modLevel-5(5), modLevel-6(6), modLevel-7(7), modLevel-8(8)}read-onlycurrent
bwaVLAdbTxFramesTotal
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.7Counter32read-onlycurrent
bwaVLAdbDroppedFramesTotal
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of frames intended to the SU/RB that were dropped because they were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.8Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel1
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 1.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.9Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel2
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 2.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.10Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel3
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 3.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.11Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel4
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 4.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.12Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel5
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 5.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.13Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel6
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 6.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.14Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel7
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 7.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.15Counter32read-onlycurrent
bwaVLAdbTxSuccessModLevel8
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 8. Not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.16Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel1
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 1.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.17Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel2
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 2.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.18Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel3
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 3.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.19Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel4
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 4.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.20Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel5
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 5.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.21Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel6
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 6.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.22Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel7
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 7.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.23Counter32read-onlycurrent
bwaVLAdbTxFailedModLevel8
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 8. Not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.24Counter32read-onlycurrent
bwaVLAdbCirTx
OBJECT-TYPE
Applicable to AU Only. Not applicable to BWA-PtP products. Read-only. The value configured in the relevant SU for the CIR: SU to AU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.25INTEGERread-onlycurrent
bwaVLAdbMirTx
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: SU/RB to AU/BU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.26INTEGERread-onlycurrent
bwaVLAdbCirRx
OBJECT-TYPE
Applicable to AU Only. Not applicable to BWA-PtP products. The value configured in the relevant SU for the CIR: AU to SU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.27INTEGERread-onlycurrent
bwaVLAdbMirRx
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: AU/BU to SU/RB parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.28INTEGERread-onlycurrent
bwaVLAdbCirMaxDelay
OBJECT-TYPE
Applicable to AU Only. Not applicable to BWA-PtP products. The value configured in the relevant SU for the CIR Maximum Delay parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.29INTEGERread-onlycurrent
bwaVLAdbDistance
OBJECT-TYPE
Applicable to AU/BU Only. The distance between the SU/RB and the AU/BU (In Kilometers).
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.30INTEGER {below-2-Km(1)}read-onlycurrent
bwaVLAdbHwRevision
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB HW Revision.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.31INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
bwaVLAdbCpldVer
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB CPLD Version.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.32DisplayStringread-onlycurrent
bwaVLAdbCountryCode
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB supported country code.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.33INTEGERread-onlycurrent
bwaVLAdbBootVer
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB Boot Version.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.34DisplayStringread-onlycurrent
bwaVLAdbAtpcOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB ATPC option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.35INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLAdbAdapModOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB adaptive modulation option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.36INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLAdbBurstModeOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB burst mode option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.37INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLAdbConcatenationOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB concatenation option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.39INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLAdbSecurityMode
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB security mode configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.41INTEGER {wep(1), aes(2), fips197(3), na(255)}read-onlycurrent
bwaVLAdbAuthOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB authentication algorithm configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.42INTEGER {openSystem(1), sharedKey(2), na(255)}read-onlycurrent
bwaVLAdbDataEncyptOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB data encryption option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.43INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
bwaVLAdbAge
OBJECT-TYPE
Applicable to AU/BU only. The time since any packet was received from the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.44INTEGERread-onlycurrent
bwaVLAdbUnitName
OBJECT-TYPE
Applicable to AU/BU only. The unit name of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.45DisplayStringread-onlycurrent
bwaVLUpLinkQualityIndicator
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.6
bwaVLMeasureUpLinkQualityIndicator
OBJECT-TYPE
Applicable to SU/RB. Starts calculation of LQI. The calculation will be for a period of 10 seconds.
1.3.6.1.4.1.12394.1.1.11.6.1INTEGER {start(1), cancel(2)}read-writecurrent
bwaVLReadUpLinkQualityIndicator
OBJECT-TYPE
Applicable to SU/RB. The results of the last LQI calculation. Range: 1 to 8.
1.3.6.1.4.1.12394.1.1.11.6.2INTEGERread-onlycurrent
bwaVLUpLinkQualityIndicatorStatus
OBJECT-TYPE
Applicable to SU/RB Only. Indicates the test conditions. fullTest means that there are no limitations on the range of available modulation levels, and that all modulation levels from 1 to 8 can be used. limitedTest indicates that the results may not indicate the true quality since the available range is limited - by HW (HW Revision A), or by the applicable parameters in the country code, or by the configurable Maximum Modulation Level parameter.
1.3.6.1.4.1.12394.1.1.11.6.3INTEGER {fullTest(1), limitedTest(2)}read-onlycurrent
bwaVLMacPinpoint
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.7
bwaVLMacPinpointTable
OBJECT-TYPE
Applicable to AU/BU only. A table that contains information about wireless device used by a certain Ethernet station in order to connect to the wireless network
1.3.6.1.4.1.12394.1.1.11.7.1not-accessiblecurrent
bwaVLMacPinpointEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the MAC Pinpoint Table. Each entry contains an Ethernet station MAC address and the MAC address of the wireless device used to connect it to the wireless network
1.3.6.1.4.1.12394.1.1.11.7.1.1not-accessiblecurrent
mptEthernetStationMACAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC address of the Ethernet station. It is used as an index in the MAC Pinpoint Table.
1.3.6.1.4.1.12394.1.1.11.7.1.1.1MacAddressread-onlycurrent
mptUnitMACAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC address of the wireless device used by the station with the MAC Address from the index in order to access the wireless network.
1.3.6.1.4.1.12394.1.1.11.7.1.1.2MacAddressread-onlycurrent
bwaVLDrapGatewaysTable
OBJECT-TYPE
This table provides information about Gateways supporting DRAP that are registered at the AU
1.3.6.1.4.1.12394.1.1.11.8not-accessiblecurrent
bwaVLDrapGatewayEntry
OBJECT-TYPE
A Drap Gateway Entry.
1.3.6.1.4.1.12394.1.1.11.8.1not-accessiblecurrent
bwaVLDrapGatewayIndex
OBJECT-TYPE
Gateway Entry's Index
1.3.6.1.4.1.12394.1.1.11.8.1.1INTEGER (1..512)read-onlycurrent
bwaVLDrapGatewayIP
OBJECT-TYPE
The IP address of the Gateway
1.3.6.1.4.1.12394.1.1.11.8.1.2IpAddressread-onlycurrent
bwaVLDrapGatewayType
OBJECT-TYPE
The Gateway type
1.3.6.1.4.1.12394.1.1.11.8.1.3INTEGER {vgDataVoice(4), vgData1Voice1(5), vgData4Voice2(6), vgDataVoice2(7), ngData4Wireless(11), vgUnknown(255)}read-onlycurrent
bwaVLDrapGatewayNoOfActiveVoiceCalls
OBJECT-TYPE
The current number of active voice calls handled by the Gateway
1.3.6.1.4.1.12394.1.1.11.8.1.4INTEGERread-onlycurrent
bwaVLTraps
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.14
bwaVLTrapSUMacAddr
OBJECT-TYPE
Applicable to AU/BU only. SU/RB MAC Address.
1.3.6.1.4.1.12394.1.1.14.1MacAddressread-onlycurrent
bwaVLTrapText
OBJECT-TYPE
Textual string for future use.
1.3.6.1.4.1.12394.1.1.14.3DisplayStringread-onlycurrent
bwaVLTrapToggle
OBJECT-TYPE
Applicable to all units. An On/Off toggle status.
1.3.6.1.4.1.12394.1.1.14.4INTEGER {on(1), off(2)}read-onlycurrent
bwaVLTrapParameterChanged
OBJECT-TYPE
Applicable to all units. A modification to one of the parameters related to CIR/MIR, IP Filtering or VLAN.
1.3.6.1.4.1.12394.1.1.14.5INTEGER {cirOrMir(1), ipFilter(2), vlan(4)}read-onlycurrent
bwaVLTrapAccessRights
OBJECT-TYPE
Applicable to all units. The access rights used for login.
1.3.6.1.4.1.12394.1.1.14.6INTEGER {notLoggedIn(1), readOnly(2), installer(3), administrator(4), factory(5)}read-onlycurrent
bwaVLTrapLog
OBJECT-TYPE
Applicable to all units. Login or logout to the Monitor program via Telnet.
1.3.6.1.4.1.12394.1.1.14.7INTEGER {telnetLogin(3), telnetLogout(4)}read-onlycurrent
bwaVLTrapTelnetUserIpAddress
OBJECT-TYPE
Applicable to all units. The IP address of a Telnet user.
1.3.6.1.4.1.12394.1.1.14.8IpAddressread-onlycurrent
bwaVLTrapRTx
OBJECT-TYPE
Applicable to AU/BU only. Retransmissions as a percentage of total transmissions.
1.3.6.1.4.1.12394.1.1.14.9INTEGERread-onlycurrent
bwaVLTrapFtpOrTftpStatus
OBJECT-TYPE
Applicable to all units. The status of the last FTP/TFTP loading procedure.
1.3.6.1.4.1.12394.1.1.14.10INTEGER {successful(1), failed(2)}read-onlycurrent
bwaVLDFSMoveFreq
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLTrapDFSMoveFreq New to support a resolution of 0.5 MHz). The new frequency in MHz after detecting radar on a previous channel.
1.3.6.1.4.1.12394.1.1.14.11INTEGERread-onlycurrent
bwaVLDFSMoveFreqNew
OBJECT-TYPE
Applicable to AU/BU. The new frequency in MHz after detecting radar on a previous channel. (Replaces bwaVLDFSMoveFreq to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.14.12DisplayStringread-onlycurrent
bwaVLEthBroadcastThresholdExceeded
OBJECT-TYPE
Applicable to all units. The number of packets that are dropped by the ethernet broadcast/multicast limiter.
1.3.6.1.4.1.12394.1.1.14.13INTEGERread-onlycurrent
bwaVLTrapSubscriberType
OBJECT-TYPE
Applicable to AUS only. The type of subscriber that was rejected by AUS
1.3.6.1.4.1.12394.1.1.14.14INTEGER {unknownSubscriberType(0), su-3(3), su-6(6), rb-14(14), su-24(24), rb-28(28), su-54(54), rb-100(100)}read-onlycurrent
bwaVLTrapMACAddress
OBJECT-TYPE
Applicable to BU/RB only. The MAC address of the BWA PtP unit whose type has been changed
1.3.6.1.4.1.12394.1.1.14.15MacAddressread-onlycurrent
bwaVLNewUnitTypeTrap
OBJECT-TYPE
Applicable to BU/RB only. The new type of the BWA PtP unit.
1.3.6.1.4.1.12394.1.1.14.16INTEGER {bu(1), rb(2)}read-onlycurrent
bwaVLTrapSWVersion
OBJECT-TYPE
The SW version of the SU that tries to associate with a station that has Wireless Link Prioritization Enabled
1.3.6.1.4.1.12394.1.1.14.17DisplayStringread-onlycurrent
bwaOID
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4
bwaVLOID
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1
bwaVLAU
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.1
bwaVLSU
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.2
bwaVLProducts
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.3
bwaVLAU_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.4
bwaVLAU_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.5
bwaVLAUS_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.6
bwaVLAUS_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.7
bwaVLAU_EZ
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.8
bwaVLSU_6_1D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.11
bwaVLSU_6_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.12
bwaVLSU_24_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.13
bwaVLSU_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.14
bwaVLSU_54_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.15
bwaVLSU_3_1D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.16
bwaVLSU_3_4D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.17
bwaVLSU_I
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.18
ptp_BU_B14
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.21
ptp_BU_B28
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.22
ptp_BU_B100
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.23
ptp_RB_B14
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.31
ptp_RB_B28
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.32
ptp_RB_B100
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.33
bwa4900_AU_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.41
bwa4900_AU_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.42
bwa4900_SU_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.51

Notifications

NameOIDStatus
bwaVLSUassociatedAUTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating a new association with an SU/RB.
1.3.6.1.4.1.12394.4.1.3.2current
bwaVLAUdisassociatedTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating that an SU/RB has been disassociated from the AU. The AU/BU decides that an SU/RB has been disassociated from it and remove it from the ADB after receiving from another AU/BU a SNAP frame with the SU/RB MAC address. The SNAP frame indicating a network topology change where the SU/RB has associated with another AU/BU will be received if both AUs/BUs are connected to the same Ethernet backbone.
1.3.6.1.4.1.12394.4.1.3.3current
bwaVLAUagingTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating that the unit association was aged out and removed from the Association database following its failure to acknowledge a specified number of consecutive frames.
1.3.6.1.4.1.12394.4.1.3.4current
bwaVLSUassociatedTRAP
NOTIFICATION-TYPE
An SU/RB trap indicating association with an AU/BU. In addition to the MAC address information of the AU/BU, the trap also includes information on the average SNR of frames received from the AU/BU.
1.3.6.1.4.1.12394.4.1.3.6current
bwaVLAUwirelessQualityTRAP
NOTIFICATION-TYPE
An AU/BU trap, indicating that the quality of the wireless link (retransmissions rate) has changed and dropped below (Off) or increased above (On) a threshold , defined by the *bwaVLWirelessTrapThreshold. The threshold for AU/BU is a percentage of retransmissions.
1.3.6.1.4.1.12394.4.1.3.20current
bwaVLPowerUpFromReset
NOTIFICATION-TYPE
An AU/BU trap indicating power up after Reset.
1.3.6.1.4.1.12394.4.1.3.101current
bwaVLTelnetStatusTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating that a log-in or log-out has been performed via Telnet. Includes the log-in access right and the IP address of the PC performing Telnet.
1.3.6.1.4.1.12394.4.1.3.102current
bwaVLParameterChangedTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating a change in a CIR/MIR, IP Filter or VLAN parameter.
1.3.6.1.4.1.12394.4.1.3.103current
bwaVLLoadingStatusTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating that last FTP/TFTP loading process has been finished successfully or failed.
1.3.6.1.4.1.12394.4.1.3.104current
bwaVLPromiscuousModeTRAP
NOTIFICATION-TYPE
An AU/BU trap, indicating that the AU/BU In (On) Promiscuous Mode or out (Off) Promiscuous Mode.
1.3.6.1.4.1.12394.4.1.3.105current
bwaVLDFSRadarDetecetedTRAP
NOTIFICATION-TYPE
DFS: Applicable to AU/BU only. A trap indicating that a radar was detected.
1.3.6.1.4.1.12394.4.1.3.106current
bwaVLDFSFrequcnyTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. A trap indicating that the unit moved to a new frequency.
1.3.6.1.4.1.12394.4.1.3.107current
bwaVLDFSNoFreeChannelsExistsTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. A trap indicating that a radar was detected and there is no free channel.
1.3.6.1.4.1.12394.4.1.3.108current
bwaVLEthBroadcastMulticatLimiterTRAP
NOTIFICATION-TYPE
Applicable to all units. The trap is send if the ethernet broadcast filter threshold is exceeded and it contains the number of dropped packets.
1.3.6.1.4.1.12394.4.1.3.109current
bwaVLAUSUnsupportedSubscriberTypeTRAP
NOTIFICATION-TYPE
Applicable to AUS only. This trap is generated when a subscriber with unsupported type tries to associate to AUS. The AUS supports only SU-3 and SU-6. The first variable of the trap is the subscriber MAC Address. The second variable is the type of subscriber
1.3.6.1.4.1.12394.4.1.3.110current
bwaVLUnitTypeChangedTRAP
NOTIFICATION-TYPE
Applicable to BU/RB only. This trap is generated when the user change the type of the BWA PtP unit. The RB can be converted in BU or vice versa. The first variable of the trap is the unit MAC Address. The second variable is the new type of the unit
1.3.6.1.4.1.12394.4.1.3.111current
bwaVLWLPrioritizationNotSupportedBySUTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. This trap is generated when an SU/RB with a SW version below 4.0 that does not support Wireless Link Prioritization is associated with an AU/BU with thw Wireless Link Prioritization Option enabled. The first variable of the trap is the SU/RB MAC Address. The second variable is the SW version of the SU/RB
1.3.6.1.4.1.12394.4.1.3.112current