BKTEL-HFC862-OVTX-V11-MIB
- Registered at
- 1.3.6.1.4.1.7501.1.2.101
- Namespace
- bktel
- Source file
BKTEL-HFC862-OVTX-V11-MIB- Digest
sha256:5eebab591e441bdf569d7dc89e17e2c42e821d942ecf7bc21638f57b3e928db2
Imports
| From | Symbols |
|---|---|
| BKTEL-HFC862-BASE-MIB | DisplayString, ModuleWidthValue, NESlotValue, PerceivedSeverityValue, TruthValue, modules |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, enterprises, experimental, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
BKTEL-HFC862-BASE-MIB BKTEL-HFC862-OVTX-V11-MIB RFC1155-SMI SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| AGCmode type | ||||
| CsoRegulationMode type | ||||
| LaserOutputMode type | ||||
| LnbSupplySupportedValue type | ||||
| LnbSupplyValue type | ||||
| NESlotWriteValue type | ||||
| RedundancyMask type | ||||
| RedundancyMode type | ||||
| RegulationState type | ||||
| RfInputAlarmMode type | ||||
| RfInputCapabilities type | ||||
| SatAGCmode type | ||||
| SbsFiberLengthValue type | ||||
| SbsFiberTypeValue type | ||||
| SbsSuppressionModeValue type |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ovtx OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101 | |||
| ovtxCommon OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.1 | |||
| ovtxCommonNumberOfModules OBJECT-TYPE Number of modules in table. | 1.3.6.1.4.1.7501.1.2.101.1.1 | INTEGER (0..50) | read-only | mandatory |
| ovtxCommonTable OBJECT-TYPE The table contains all modules of the OVTX-type in the NE | 1.3.6.1.4.1.7501.1.2.101.1.2 | not-accessible | mandatory | |
| ovtxCommonEntry OBJECT-TYPE Common-Values for a module. | 1.3.6.1.4.1.7501.1.2.101.1.2.1 | not-accessible | mandatory | |
| ovtxNESlot OBJECT-TYPE The slot number of the chassis for which this entry contains management information. Equal to: modOVTXv11UniqueID | 1.3.6.1.4.1.7501.1.2.101.1.2.1.1 | NESlotValue | read-only | mandatory |
| ovtxCommonType OBJECT-TYPE The type of physical module. modSlotEmpty indicates an empty slot. A Value of modSlotUnknown indicates that the type of module is unknown. | 1.3.6.1.4.1.7501.1.2.101.1.2.1.2 | DisplayString (SIZE(0..32)) | read-only | mandatory |
| ovtxCommonDescr OBJECT-TYPE A textual description of the module. If not available, this Value should be set to a zero length string. | 1.3.6.1.4.1.7501.1.2.101.1.2.1.3 | DisplayString | read-write | mandatory |
| ovtxCommonFirmwareId OBJECT-TYPE The firmware Id of the module. | 1.3.6.1.4.1.7501.1.2.101.1.2.1.4 | DisplayString (SIZE(0..32)) | read-only | mandatory |
| ovtxCommonModuleWidth OBJECT-TYPE The width of the module in multiples of slots (1, 2, ...) | 1.3.6.1.4.1.7501.1.2.101.1.2.1.5 | ModuleWidthValue | read-only | optional |
| ovtxStates OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.2 | |||
| ovtxStatesTable OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.2.1 | not-accessible | mandatory | |
| ovtxStatesEntry OBJECT-TYPE Alarms for a module. | 1.3.6.1.4.1.7501.1.2.101.2.1.1 | not-accessible | mandatory | |
| ovtxStatesOutputLow OBJECT-TYPE Optical output power low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.1 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesOutputHigh OBJECT-TYPE Optical output power high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.2 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesInputLow OBJECT-TYPE RF input power low (CATV input) | 1.3.6.1.4.1.7501.1.2.101.2.1.1.3 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesLaserAging OBJECT-TYPE The laser is aging | 1.3.6.1.4.1.7501.1.2.101.2.1.1.4 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesTecHigh OBJECT-TYPE Laser cooler limit reached | 1.3.6.1.4.1.7501.1.2.101.2.1.1.5 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesLaserTempLow OBJECT-TYPE Laser temperature low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.6 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesLaserTempHigh OBJECT-TYPE Laser temperature high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.7 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesOmiOrRfgainLow OBJECT-TYPE Omi or rf-gain (depending on mode) low (CATV input) | 1.3.6.1.4.1.7501.1.2.101.2.1.1.8 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesOmiOrRfgainHigh OBJECT-TYPE Omi or rf-gain (depending on mode) high (CATV input) | 1.3.6.1.4.1.7501.1.2.101.2.1.1.9 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPowerSupplyLeft OBJECT-TYPE The left (looking from front) power supply unit fails | 1.3.6.1.4.1.7501.1.2.101.2.1.1.10 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPowerSupplyRight OBJECT-TYPE The right (looking from front) power supply unit fails | 1.3.6.1.4.1.7501.1.2.101.2.1.1.11 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesFanLeft OBJECT-TYPE The left (looking from front) fan unit fails | 1.3.6.1.4.1.7501.1.2.101.2.1.1.12 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesFanRight OBJECT-TYPE The right (looking from front) fan unit fails | 1.3.6.1.4.1.7501.1.2.101.2.1.1.13 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesTemperatureLow OBJECT-TYPE Device internal temperature low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.14 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesTemperatureHigh OBJECT-TYPE Device internal temperature high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.15 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus3p3VLow OBJECT-TYPE 3.3 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.16 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus3p3VHigh OBJECT-TYPE 3.3 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.17 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus5VLow OBJECT-TYPE 5 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.18 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus5VHigh OBJECT-TYPE 5 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.19 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus12VLow OBJECT-TYPE 12 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.20 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus12VHigh OBJECT-TYPE 12 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.21 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus24VLow OBJECT-TYPE 24 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.22 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesPlus24VHigh OBJECT-TYPE 24 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.23 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesMinus5VLow OBJECT-TYPE -5 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.24 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesMinus5VHigh OBJECT-TYPE -5 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.25 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesMinus12VLow OBJECT-TYPE -12 Volt supply low | 1.3.6.1.4.1.7501.1.2.101.2.1.1.26 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesMinus12VHigh OBJECT-TYPE -12 Volt supply high | 1.3.6.1.4.1.7501.1.2.101.2.1.1.27 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesLaserShutdown OBJECT-TYPE Laser is shutdown, no optical output | 1.3.6.1.4.1.7501.1.2.101.2.1.1.28 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesInitializing OBJECT-TYPE The device is initializing | 1.3.6.1.4.1.7501.1.2.101.2.1.1.29 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesBootloader OBJECT-TYPE The device is running in bootloader mode without a legal application software. | 1.3.6.1.4.1.7501.1.2.101.2.1.1.30 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesCommLoss OBJECT-TYPE The NEC has lost the connection to the device. Reason may be a removed or defective device. Note that this state is set by the NEC and not by the device | 1.3.6.1.4.1.7501.1.2.101.2.1.1.31 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesInputHigh OBJECT-TYPE RF input power high (CATV input) | 1.3.6.1.4.1.7501.1.2.101.2.1.1.32 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesRedundancySwitch OBJECT-TYPE This (redundant) device has been activated (redundancy switchover) | 1.3.6.1.4.1.7501.1.2.101.2.1.1.33 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSatInputLow OBJECT-TYPE RF input power low (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.34 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSatInputHigh OBJECT-TYPE RF input power high (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.35 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSatOmiOrRfgainLow OBJECT-TYPE Omi or rf-gain (depending on mode) low (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.36 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSatOmiOrRfgainHigh OBJECT-TYPE Omi or rf-gain (depending on mode) high (SAT input) Only used if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.37 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSatLnbShortCircuit OBJECT-TYPE Short-circuit at SAT LNB Only used if ovtxDisplaySatLnbSupplySupported != notSupported(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.38 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSbs1Level OBJECT-TYPE SBS #1 level alarm Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.39 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSbs2Level OBJECT-TYPE SBS #2 level alarm Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.40 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSbs1PllNotLocked OBJECT-TYPE SBS #1 PLL not locked Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.41 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesSbs2PllNotLocked OBJECT-TYPE SBS #2 PLL not locked Only used if ovtxDisplaySbsExtensionsSupported == true(1), otherwise always reports clear(5). | 1.3.6.1.4.1.7501.1.2.101.2.1.1.42 | PerceivedSeverityValue | read-only | mandatory |
| ovtxStatesInternalAlarm OBJECT-TYPE Internal hardware failure | 1.3.6.1.4.1.7501.1.2.101.2.1.1.43 | PerceivedSeverityValue | read-only | mandatory |
| ovtxConfiguration OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.3 | |||
| ovtxConfigurationTable OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.3.1 | not-accessible | mandatory | |
| ovtxConfigurationEntry OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.3.1.1 | not-accessible | mandatory | |
| ovtxConfigurationNESlotWrite OBJECT-TYPE By writing this variable a slot can be assigned for devices that dont support hardware slot detection. Reading '-1' means that the slot position is NOT writable. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.1 | NESlotWriteValue | read-write | optional |
| ovtxConfigurationModeAGC OBJECT-TYPE The AGC mode of the optical transmitter (CATV input). | 1.3.6.1.4.1.7501.1.2.101.3.1.1.2 | AGCmode | read-write | mandatory |
| ovtxConfigurationOmi OBJECT-TYPE The desired offset from nominal OMI in 0.1dB units (CATV input). This parameter is only used if AGC is on. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.3 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfGain OBJECT-TYPE The desired offset from nominal gain in 0.1dB units (CATV input). This parameter is only used if AGC is off. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.4 | INTEGER | read-write | mandatory |
| ovtxConfigurationSbsSuppression OBJECT-TYPE The sbs suppression in 0.1dBm units. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.5 | INTEGER | read-write | mandatory |
| ovtxConfigurationChannelDistance OBJECT-TYPE The channel raster in MHz units. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.6 | INTEGER | read-write | mandatory |
| ovtxConfigurationLaserFrequency OBJECT-TYPE The laser frequency in GHz units. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.7 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfInputLimitLoLo OBJECT-TYPE The rf input power low alarm limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.8 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfInputLimitLo OBJECT-TYPE The rf input power low warning limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.9 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfInputLimitHi OBJECT-TYPE The rf input power high warning limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.10 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfInputLimitHiHi OBJECT-TYPE The rf input power high alarm limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.11 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfGainMeasuredLimitLoLo OBJECT-TYPE The Measured-Rf-Gain offset low alarm limit in 0.1 dB units (in AGC ON mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.12 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfGainMeasuredLimitLo OBJECT-TYPE The Measured-Rf-Gain offset low warning limit in 0.1 dB units (in AGC ON mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.13 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfGainMeasuredLimitHi OBJECT-TYPE The Measured-Rf-Gain offset high warning limit in 0.1 dB units (in AGC ON mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.14 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfGainMeasuredLimitHiHi OBJECT-TYPE The Measured-Rf-Gain offset high alarm limit in 0.1 dB units (in AGC ON mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.15 | INTEGER | read-write | mandatory |
| ovtxConfigurationOmiMeasuredLimitLoLo OBJECT-TYPE The Measured-OMI offset low alarm limit in 0.1 dB units (in AGC OFF mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.16 | INTEGER | read-write | mandatory |
| ovtxConfigurationOmiMeasuredLimitLo OBJECT-TYPE The Measured-OMI offset low warning limit in 0.1 dB units(in AGC OFF mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.17 | INTEGER | read-write | mandatory |
| ovtxConfigurationOmiMeasuredLimitHi OBJECT-TYPE The Measured-OMI offset high warning limit in 0.1 dB units(in AGC OFF mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.18 | INTEGER | read-write | mandatory |
| ovtxConfigurationOmiMeasuredLimitHiHi OBJECT-TYPE The Measured-OMI offset high alarm limit in 0.1 dB units(in AGC OFF mode) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.19 | INTEGER | read-write | mandatory |
| ovtxConfigurationOutputPwrLimitLoLo OBJECT-TYPE The output power low alarm limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.20 | INTEGER | read-write | mandatory |
| ovtxConfigurationOutputPwrLimitLo OBJECT-TYPE The output power low warning limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.21 | INTEGER | read-write | mandatory |
| ovtxConfigurationOutputPwrLimitHi OBJECT-TYPE The output power high warning limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.22 | INTEGER | read-write | mandatory |
| ovtxConfigurationOutputPwrLimitHiHi OBJECT-TYPE The output power high alarm limit in 0.1 dBm units | 1.3.6.1.4.1.7501.1.2.101.3.1.1.23 | INTEGER | read-write | mandatory |
| ovtxConfigurationRedundancyMode OBJECT-TYPE The device's redundancy mode. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.24 | RedundancyMode | read-write | mandatory |
| ovtxConfigurationRedundancyMask OBJECT-TYPE The device's redundancy mask setings. | 1.3.6.1.4.1.7501.1.2.101.3.1.1.25 | RedundancyMask | read-write | mandatory |
| ovtxConfigurationCsoRegulationMode OBJECT-TYPE The desired CSO regulation mode of the optical transmitter. Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports csoRegModeChannelControlled(1) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.26 | CsoRegulationMode | read-write | mandatory |
| ovtxConfigurationSlope OBJECT-TYPE The desired slope in 0.1 dB units (CATV input). Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.3.1.1.27 | INTEGER | read-write | mandatory |
| ovtxConfigurationFiberLength OBJECT-TYPE The optical fiber length in meter units. Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.3.1.1.28 | INTEGER | read-write | mandatory |
| ovtxConfigurationSatModeAGC OBJECT-TYPE The AGC mode of the optical transmitter (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports satAgcOff(1) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.29 | SatAGCmode | read-write | mandatory |
| ovtxConfigurationSatOmi OBJECT-TYPE The desired offset from nominal OMI in 0.1dB units (SAT input). This parameter is only used if AGC is on. Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.3.1.1.30 | INTEGER | read-write | mandatory |
| ovtxConfigurationSatRfGain OBJECT-TYPE The desired offset from nominal gain in 0.1dB units (SAT input). This parameter is only used if AGC is off. Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.3.1.1.31 | INTEGER | read-write | mandatory |
| ovtxConfigurationSatSlope OBJECT-TYPE The desired slope in 0.1 dB units (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.3.1.1.32 | INTEGER | read-write | mandatory |
| ovtxConfigurationRfInputAlarmMode OBJECT-TYPE The RF input alarm mode (Can be used to disable alarms of unused RF inputs) Only usable if ovtxDisplayRfInputCapabilities == rfInputCatvAndSatSupported(3), otherwise always reports alarmEnableAll(1) | 1.3.6.1.4.1.7501.1.2.101.3.1.1.33 | RfInputAlarmMode | read-write | mandatory |
| ovtxConfigurationSatLnbSupply OBJECT-TYPE SAT LNB supply control. This feature is not supported by all transmitter devices, see ovtxDisplaySatLnbSupplySupported | 1.3.6.1.4.1.7501.1.2.101.3.1.1.34 | LnbSupplyValue | read-write | mandatory |
| ovtxConfigurationSbsSuppressionMode OBJECT-TYPE SBS suppression mode. This feature is not supported by all transmitter devices, see ovtxDisplaySbsSuppressionModeSupported | 1.3.6.1.4.1.7501.1.2.101.3.1.1.35 | SbsSuppressionModeValue | read-write | mandatory |
| ovtxConfigurationSbsFiberType OBJECT-TYPE SBS fiber type. This feature is not supported by all transmitter devices, see ovtxDisplaySbsFiberParametersSupported | 1.3.6.1.4.1.7501.1.2.101.3.1.1.36 | SbsFiberTypeValue | read-write | mandatory |
| ovtxConfigurationSbsFiberLength OBJECT-TYPE SBS suppression mode. This feature is not supported by all transmitter devices, see ovtxDisplaySbsFiberParametersSupported | 1.3.6.1.4.1.7501.1.2.101.3.1.1.37 | SbsFiberLengthValue | read-write | mandatory |
| ovtxControl OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.4 | |||
| ovtxControlTable OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.4.1 | not-accessible | mandatory | |
| ovtxControlEntry OBJECT-TYPE Alarms for a module. | 1.3.6.1.4.1.7501.1.2.101.4.1.1 | not-accessible | mandatory | |
| ovtxControlLaserOutputMode OBJECT-TYPE The output mode of the laser. NOTE: The error mask used for parameter 'laserShutdownOnMaskedError(3)' is the same mask used for external IO port, 'ovtxConfigurationRedundancyMask' | 1.3.6.1.4.1.7501.1.2.101.4.1.1.1 | LaserOutputMode | read-write | mandatory |
| ovtxControlReset OBJECT-TYPE Reset the module. | 1.3.6.1.4.1.7501.1.2.101.4.1.1.2 | TruthValue | read-write | mandatory |
| ovtxControlModuleLedBlink OBJECT-TYPE Writing this variable to true(1) lets the device's modul LED blink green for 10 seconds. Writing this variable to false(2) stops blinking at once. This variable always returns false(2) on read requests | 1.3.6.1.4.1.7501.1.2.101.4.1.1.3 | TruthValue | read-write | mandatory |
| ovtxMeasuringValues OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.5 | |||
| ovtxMeasuringValuesTable OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.5.1 | not-accessible | mandatory | |
| ovtxMeasuringValuesEntry OBJECT-TYPE Common-Values for a module. | 1.3.6.1.4.1.7501.1.2.101.5.1.1 | not-accessible | mandatory | |
| ovtxOmiMeasuredLoLo OBJECT-TYPE Measured-OMI offset low alarm threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.1 | INTEGER | read-write | mandatory |
| ovtxOmiMeasuredLo OBJECT-TYPE Measured-OMI offset low warning threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.2 | INTEGER | read-write | mandatory |
| ovtxOmiMeasuredValue OBJECT-TYPE The offset from nominal OMI in steps of 0.1dB (CATV input). If AGC is on this parameter is equal to ovtxConfigurationOmi. If AGC is off this paramters shows the Measured-OMI for the adjusted gain. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.3 | INTEGER | read-only | mandatory |
| ovtxOmiMeasuredHi OBJECT-TYPE Measured-OMI offset high warning threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.4 | INTEGER | read-write | mandatory |
| ovtxOmiMeasuredHiHi OBJECT-TYPE Measured-OMI offset high alarm threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.5 | INTEGER | read-write | mandatory |
| ovtxRfGainMeasuredLoLo OBJECT-TYPE Measured-Rf-Gain offset low alarm threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.6 | INTEGER | read-write | mandatory |
| ovtxRfGainMeasuredLo OBJECT-TYPE Measured-Rf-Gain offset low warning threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.7 | INTEGER | read-write | mandatory |
| ovtxRfGainMeasuredValue OBJECT-TYPE The offset from nominal gain in steps of 0.1dB (CATV input). If AGC is off this parameter is equal to ovtxConfigurationRfGain. If AGC is on this paramters shows the Measured-Rf-Gain for the adjusted omi. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.8 | INTEGER | read-only | mandatory |
| ovtxRfGainMeasuredHi OBJECT-TYPE Measured-Rf-Gain offset high warning threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.9 | INTEGER | read-write | mandatory |
| ovtxRfGainMeasuredHiHi OBJECT-TYPE Measured-Rf-Gain offset high alarm threshold in steps of 0.1dB (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.10 | INTEGER | read-write | mandatory |
| ovtxLaserCurrentRelLoLo OBJECT-TYPE Relative laser current low alarm threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.11 | INTEGER | read-only | mandatory |
| ovtxLaserCurrentRelLo OBJECT-TYPE Relative laser current low warning threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.12 | INTEGER | read-only | mandatory |
| ovtxLaserCurrentRelValue OBJECT-TYPE The laser current relative to the current at begin of life in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.13 | INTEGER | read-only | mandatory |
| ovtxLaserCurrentRelHi OBJECT-TYPE Relative laser current high warning threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.14 | INTEGER | read-only | mandatory |
| ovtxLaserCurrentRelHiHi OBJECT-TYPE Relative laser current high alarm threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.15 | INTEGER | read-only | mandatory |
| ovtxTecCurrentRelLoLo OBJECT-TYPE Thermo-electric-cooler current low alarm threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.16 | INTEGER | read-only | mandatory |
| ovtxTecCurrentRelLo OBJECT-TYPE Thermo-electric-cooler current low warning threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.17 | INTEGER | read-only | mandatory |
| ovtxTecCurrentRelValue OBJECT-TYPE The thermo-electric-cooler current relative to its absolute high alarm threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.18 | INTEGER | read-only | mandatory |
| ovtxTecCurrentRelHi OBJECT-TYPE Thermo-electric-cooler current high warning threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.19 | INTEGER | read-only | mandatory |
| ovtxTecCurrentRelHiHi OBJECT-TYPE Thermo-electric-cooler current high alarm threshold in steps of 0.1%. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.20 | INTEGER | read-only | mandatory |
| ovtxOutputPowerLoLo OBJECT-TYPE Output power low alarm threshold in steps of 0.1dBm. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.21 | INTEGER | read-write | mandatory |
| ovtxOutputPowerLo OBJECT-TYPE Output power low warning threshold in steps of 0.1dBm. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.22 | INTEGER | read-write | mandatory |
| ovtxOutputPowerValue OBJECT-TYPE Output power in steps of 0.1dBm. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.23 | INTEGER | read-only | mandatory |
| ovtxOutputPowerHi OBJECT-TYPE Output power high warning threshold in steps of 0.1dBm. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.24 | INTEGER | read-write | mandatory |
| ovtxOutputPowerHiHi OBJECT-TYPE Output power high alarm threshold in steps of 0.1dBm. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.25 | INTEGER | read-write | mandatory |
| ovtxPlus3p3VLoLo OBJECT-TYPE The +3.3V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.26 | INTEGER | read-only | mandatory |
| ovtxPlus3p3VLo OBJECT-TYPE The +3.3V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.27 | INTEGER | read-only | mandatory |
| ovtxPlus3p3VValue OBJECT-TYPE The +3.3V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.28 | INTEGER | read-only | mandatory |
| ovtxPlus3p3VHi OBJECT-TYPE The +3.3V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.29 | INTEGER | read-only | mandatory |
| ovtxPlus3p3VHiHi OBJECT-TYPE The +3.3V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.30 | INTEGER | read-only | mandatory |
| ovtxPlus5VLoLo OBJECT-TYPE The +5V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.31 | INTEGER | read-only | mandatory |
| ovtxPlus5VLo OBJECT-TYPE The +5V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.32 | INTEGER | read-only | mandatory |
| ovtxPlus5VValue OBJECT-TYPE The +5V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.33 | INTEGER | read-only | mandatory |
| ovtxPlus5VHi OBJECT-TYPE The +5V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.34 | INTEGER | read-only | mandatory |
| ovtxPlus5VHiHi OBJECT-TYPE The +5V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.35 | INTEGER | read-only | mandatory |
| ovtxPlus12VLoLo OBJECT-TYPE The +12V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.36 | INTEGER | read-only | mandatory |
| ovtxPlus12VLo OBJECT-TYPE The +12V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.37 | INTEGER | read-only | mandatory |
| ovtxPlus12VValue OBJECT-TYPE The +12V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.38 | INTEGER | read-only | mandatory |
| ovtxPlus12VHi OBJECT-TYPE The +12V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.39 | INTEGER | read-only | mandatory |
| ovtxPlus12VHiHi OBJECT-TYPE The +12V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.40 | INTEGER | read-only | mandatory |
| ovtxPlus24VLoLo OBJECT-TYPE The +24V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.41 | INTEGER | read-only | mandatory |
| ovtxPlus24VLo OBJECT-TYPE The +24V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.42 | INTEGER | read-only | mandatory |
| ovtxPlus24VValue OBJECT-TYPE The +24V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.43 | INTEGER | read-only | mandatory |
| ovtxPlus24VHi OBJECT-TYPE The +24V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.44 | INTEGER | read-only | mandatory |
| ovtxPlus24VHiHi OBJECT-TYPE The +24V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.45 | INTEGER | read-only | mandatory |
| ovtxMinus5VLoLo OBJECT-TYPE The -5V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.46 | INTEGER | read-only | mandatory |
| ovtxMinus5VLo OBJECT-TYPE The -5V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.47 | INTEGER | read-only | mandatory |
| ovtxMinus5VValue OBJECT-TYPE The -5V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.48 | INTEGER | read-only | mandatory |
| ovtxMinus5VHi OBJECT-TYPE The -5V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.49 | INTEGER | read-only | mandatory |
| ovtxMinus5VHiHi OBJECT-TYPE The -5V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.50 | INTEGER | read-only | mandatory |
| ovtxMinus12VLoLo OBJECT-TYPE The -12V supply voltage low alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.51 | INTEGER | read-only | mandatory |
| ovtxMinus12VLo OBJECT-TYPE The -12V supply voltage low warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.52 | INTEGER | read-only | mandatory |
| ovtxMinus12VValue OBJECT-TYPE The -12V supply voltage in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.53 | INTEGER | read-only | mandatory |
| ovtxMinus12VHi OBJECT-TYPE The -12V supply voltage high warning threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.54 | INTEGER | read-only | mandatory |
| ovtxMinus12VHiHi OBJECT-TYPE The -12V supply voltage high alarm threshold in steps of 0.1V. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.55 | INTEGER | read-only | mandatory |
| ovtxTemperatureLoLo OBJECT-TYPE The module temperature low alarm threshold in steps of 0.1 celsius degrees. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.56 | INTEGER | read-only | mandatory |
| ovtxTemperatureLo OBJECT-TYPE The module temperature low warning threshold in steps of 0.1 celsius degrees. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.57 | INTEGER | read-only | mandatory |
| ovtxTemperatureValue OBJECT-TYPE The module temperature in steps of 0.1 celsius degrees. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.58 | INTEGER | read-only | mandatory |
| ovtxTemperatureHi OBJECT-TYPE The module temperature high warning threshold in steps of 0.1 celsius degrees. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.59 | INTEGER | read-only | mandatory |
| ovtxTemperatureHiHi OBJECT-TYPE The module temperature high alarm threshold in steps of 0.1 celsius degrees. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.60 | INTEGER | read-only | mandatory |
| ovtxRfInputLoLo OBJECT-TYPE RfInput (total rms) low alarm threshold in steps of 0.1 dBm (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.61 | INTEGER | read-write | mandatory |
| ovtxRfInputLo OBJECT-TYPE RfInput (total rms) low warning threshold in steps of 0.1 dBm (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.62 | INTEGER | read-write | mandatory |
| ovtxRfInputValue OBJECT-TYPE RfInput (total rms) in steps of 0.1 dBm (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.63 | INTEGER | read-only | mandatory |
| ovtxRfInputHi OBJECT-TYPE RfInput (total rms) high warning threshold in steps of 0.1 dBm (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.64 | INTEGER | read-write | mandatory |
| ovtxRfInputHiHi OBJECT-TYPE RfInput (total rms) high alarm threshold in steps of 0.1 dBm (CATV input). | 1.3.6.1.4.1.7501.1.2.101.5.1.1.65 | INTEGER | read-write | mandatory |
| ovtxSatRfInputLoLo OBJECT-TYPE RfInput (total rms) low alarm threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.66 | INTEGER | read-write | mandatory |
| ovtxSatRfInputLo OBJECT-TYPE RfInput (total rms) low warning threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.67 | INTEGER | read-write | mandatory |
| ovtxSatRfInputValue OBJECT-TYPE RfInput (total rms) in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.68 | INTEGER | read-only | mandatory |
| ovtxSatRfInputHi OBJECT-TYPE RfInput (total rms) high warning threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.69 | INTEGER | read-write | mandatory |
| ovtxSatRfInputHiHi OBJECT-TYPE RfInput (total rms) high alarm threshold in steps of 0.1 dBm (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.70 | INTEGER | read-write | mandatory |
| ovtxSatOmiMeasuredLoLo OBJECT-TYPE Measured-OMI offset low alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.71 | INTEGER | read-write | mandatory |
| ovtxSatOmiMeasuredLo OBJECT-TYPE Measured-OMI offset low warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.72 | INTEGER | read-write | mandatory |
| ovtxSatOmiMeasuredValue OBJECT-TYPE The offset from nominal OMI in steps of 0.1dB (SAT input). If SAT AGC is on this parameter is equal to ovtxConfigurationSatOmi. If SAT AGC is off this paramters shows the measured-OMI for the adjusted gain. Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.73 | INTEGER | read-only | mandatory |
| ovtxSatOmiMeasuredHi OBJECT-TYPE Measured-OMI offset high warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.74 | INTEGER | read-write | mandatory |
| ovtxSatOmiMeasuredHiHi OBJECT-TYPE Measured-OMI offset high alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.75 | INTEGER | read-write | mandatory |
| ovtxSatRfGainMeasuredLoLo OBJECT-TYPE Measured-Rf-Gain offset low alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.76 | INTEGER | read-write | mandatory |
| ovtxSatRfGainMeasuredLo OBJECT-TYPE Measured-Rf-Gain offset low warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.77 | INTEGER | read-write | mandatory |
| ovtxSatRfGainMeasuredValue OBJECT-TYPE The offset from nominal gain in steps of 0.1dB (SAT input). If AGC is off this parameter is equal to ovtxConfigurationSatRfGain. If AGC is on this paramters shows the measured-Rf-Gain for the adjusted omi. Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.78 | INTEGER | read-only | mandatory |
| ovtxSatRfGainMeasuredHi OBJECT-TYPE Measured-Rf-Gain offset high warning threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.79 | INTEGER | read-write | mandatory |
| ovtxSatRfGainMeasuredHiHi OBJECT-TYPE Measured-Rf-Gain offset high alarm threshold in steps of 0.1dB (SAT input). Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero. | 1.3.6.1.4.1.7501.1.2.101.5.1.1.80 | INTEGER | read-write | mandatory |
| ovtxDisplay OBJECT-IDENTITY | 1.3.6.1.4.1.7501.1.2.101.6 | |||
| ovtxDisplayTable OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.6.1 | not-accessible | mandatory | |
| ovtxDisplayEntry OBJECT-TYPE | 1.3.6.1.4.1.7501.1.2.101.6.1.1 | not-accessible | mandatory | |
| ovtxDisplayRfInputValue OBJECT-TYPE RfInput (total rms) in steps of 0.1 dBm. | 1.3.6.1.4.1.7501.1.2.101.6.1.1.1 | INTEGER | read-only | mandatory |
| ovtxDisplayLaserFrequencyMin OBJECT-TYPE The minimum adjustable laser frequency in GHz units. | 1.3.6.1.4.1.7501.1.2.101.6.1.1.2 | INTEGER | read-only | mandatory |
| ovtxDisplayLaserFrequencyMax OBJECT-TYPE The maximum adjustable laser frequency in GHz units. | 1.3.6.1.4.1.7501.1.2.101.6.1.1.3 | INTEGER | read-only | mandatory |
| ovtxDisplayLaserFrequencyStep OBJECT-TYPE The supported laser frequency stepsize in GHz units. | 1.3.6.1.4.1.7501.1.2.101.6.1.1.4 | INTEGER | read-only | mandatory |
| ovtxDisplayOmiNominal OBJECT-TYPE The nominal OMI in 0.1 percent units (CATV input) | 1.3.6.1.4.1.7501.1.2.101.6.1.1.5 | INTEGER | read-only | mandatory |
| ovtxDisplaySatOmiNominal OBJECT-TYPE The nominal OMI in 0.1 percent units (SAT input) Only usable if ovtxDisplayRfInputCapabilities != rfInputCatvOnlySupported(1), otherwise always reports zero | 1.3.6.1.4.1.7501.1.2.101.6.1.1.6 | INTEGER | read-only | mandatory |
| ovtxDisplayRegulationState OBJECT-TYPE The transmitters current regulation state Only usable if ovtxDisplayExtendedCapabilities == true(1), otherwise always reports regulationStateUnknownOrNotSupported(1) | 1.3.6.1.4.1.7501.1.2.101.6.1.1.7 | RegulationState | read-only | mandatory |
| ovtxDisplayExtendedCapabilities OBJECT-TYPE Returns true(1) if the transmitter supports the extended features represented by the variables ovtxConfigurationCsoRegulationMode, ovtxConfigurationSlope and ovtxConfigurationFiberLength | 1.3.6.1.4.1.7501.1.2.101.6.1.1.8 | TruthValue | read-only | mandatory |
| ovtxDisplayRfInputCapabilities OBJECT-TYPE Returns the transmitter supported RF input capabilities | 1.3.6.1.4.1.7501.1.2.101.6.1.1.9 | RfInputCapabilities | read-only | mandatory |
| ovtxDisplaySatLnbSupplySupported OBJECT-TYPE Returns the supported SAT LNB supply features | 1.3.6.1.4.1.7501.1.2.101.6.1.1.10 | LnbSupplySupportedValue | read-only | mandatory |
| ovtxDisplaySbsExtensionsSupported OBJECT-TYPE Returns true(1) if the transmitter supports the extended SBS alarm features | 1.3.6.1.4.1.7501.1.2.101.6.1.1.11 | TruthValue | read-only | mandatory |
| ovtxDisplaySbsSuppressionModeSupported OBJECT-TYPE Returns true(1) if the transmitter supports the SbsSuppressionMode configuration feature | 1.3.6.1.4.1.7501.1.2.101.6.1.1.12 | TruthValue | read-only | mandatory |
| ovtxDisplaySbsFiberParametersSupported OBJECT-TYPE Returns true(1) if the transmitter supports the SbsFiber configuration feature | 1.3.6.1.4.1.7501.1.2.101.6.1.1.13 | TruthValue | read-only | mandatory |