MIBs Depot

AcBoard

Registered at
1.3.6.1.4.1.5003
Last updated
2012-08-13 11:37
Organization
AudioCodes Ltd
Revisions
2004-01-26 11:53
Namespace
audiocodes
Source file
AcBoard
Digest
sha256:dc393f2bc25d04b043c11f003b64b57faaff9cbd3851f92e055e7619fa6c6535

Description

AudioCodes Proprietary MIB Contains The managed objects of AudioCodes systems. Through this MIB, the User can set up the board configuration parameters, reset the board, and monitor the board's operational robustness and quality of service during run-time. This MIB has the following Groups: boardConfiguration boardInformation channelConfiguration channelStatus notifications reset boardConfiguration: When The user Get Parameter from most of sub-groups in boardConfiguration group, he gets the value that should be burned to the board after the next Remote Reset. He can Set new values to many parameters, and these values will burned to the board after the next remote Reset In the sub-group mGCPDefaultChannelSettings the parameters are the actual parameters, that will take place when opening channel. (Reset is not needed for that sub-group). BoardInformation: Contains Read-only parameters like: board name, serial number, number of channels, software version. ChannelConfiguration: Read-only Parameters to see the configuratin of each channel: voice settings, fax settings, etc. ChannelStatus: Read-only parameters about the status of channel, like: Is the channle active, is it in Silence Period, is it in Fax mode, ON/Off hook, etc. This group contains also counters: packets to DSP, errors, lost packets, underruns, etc. Notifications: In this version, the notification we have are: acEvBoardStarted, and acEvResetingBoard. The board should send these notifications to its manager that the user defined in INI file with the parameter: NMPManagerIP = (IP address). Reset: To remote reset the board, the user should set an integer value to the parameter remoteReset. Then he should get the trap acEvResettingBoard. Note: Before Reset, The current boardConfiguration parameters will be burned to the board. The user should not use INI file, if he wants these parameters to take place. To set the default values, the user should set an integer value to the parameter acSetDefaults.

Contact

Postal: Support AudioCodes LTD 1 Hayarden Street Airport City Lod, ISRAEL 70151 Tel: 972-3-9764000 Fax: 972-3-9764040 Email: support@audiocodes.com Web: www.audiocodes.com

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIIpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDateAndTime, DisplayString, TAddress, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

AcBoard
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.5003.8acGeneric
1.3.6.1.4.1.5003.9acProducts
1.3.6.1.4.1.5003.10acPerformanceAcPerfH323SIPGateway
1.3.6.1.4.1.5003.11acFaultAcAlarm
1.3.6.1.4.1.5003.12acExperimentalAUDIOCODES-TYPES-MIB

Objects

NameOIDSyntaxAccessStatus
audioCodes
OBJECT-IDENTITY
1.3.6.1.4.1.5003
acRegistrations
OBJECT-IDENTITY
1.3.6.1.4.1.5003.7
acGeneric
OBJECT-IDENTITY
1.3.6.1.4.1.5003.8
acProducts
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9
acBoardMibs
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10
boardConfiguration
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1
boardTDMBusSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.1
pCMLawSelect
OBJECT-TYPE
Selects the type of PCM companding law in input/output TDM bus (TDM bus is defined using the TDMBusType parameter).
1.3.6.1.4.1.5003.9.10.1.1.1.1INTEGER {aLaw(1), muLaw(3)}read-writeobsolete
tDMBusClockSource
OBJECT-TYPE
Selects the clock source on which the board synchronizes
1.3.6.1.4.1.5003.9.10.1.1.1.2INTEGER {acTDMBusClockSource-Internal(1), acTDMBusClockSource-MVIP(3), acTDMBusClockSource-Network(4), acTDMBusClockSource-H110-A(8), acTDMBusClockSource-H110-B(9), acTDMBusClockSource-NetReference1(10), acTDMBusClockSource-NetReference2(11), acTDMBusClockSource-SC-2M(12), acTDMBusClockSource-SC-4M(13), acTDMBusClockSource-SC-8M(14), acTDMBusClockSource-BITS(15), acTDMBusClockSource-Network-B(16), acTDMBusClockSource-ATM-OC3(17), acTDMBusClockSource-ATM-OC3-B(18), acTDMBusClockSource-ATM-OC12(19)}read-writeobsolete
tDMBusEnableFallBack
OBJECT-TYPE
Enable/Disable clock fallback. The Fall Back clock is determined by BSPTDMBusFallbackClock
1.3.6.1.4.1.5003.9.10.1.1.1.3INTEGER {disable(0), enable(1)}read-writeobsolete
tDMBusLocalReference
OBJECT-TYPE
When ClockSource is set to acH110BusClockSource_Network this parameter selects the TrunkID to be used as the clock synchronization source of the board. When using H.110/H.100 bus this parameter also selects the trunk which is used as the clock source for the NETREF clock generation (in this case ClockSource might not be set to acH110BusClockSource_Network).
1.3.6.1.4.1.5003.9.10.1.1.1.4INTEGER (0..27)read-writeobsolete
idlePCMPattern
OBJECT-TYPE
PCM Pattern applied to E1/T1 timeslot (B-channel) when channel is idle.
1.3.6.1.4.1.5003.9.10.1.1.1.5INTEGER (0..255)read-writeobsolete
idleABCD
OBJECT-TYPE
ABCD (CAS) Pattern to be applied to CAS signaling bus before changed by the user or PSTN protocol. This is only relevant when using PSTN interface with CAS protocols.
1.3.6.1.4.1.5003.9.10.1.1.1.6INTEGER (0..15)read-writeobsolete
tDMBusMasterSlaveSelection
OBJECT-TYPE
Set SC/MVIP/H.110 to either: Master mode (the board is the clock source for the TDM bus) or Slave mode (some other board in the system must supply the clock to the TDM bus).
1.3.6.1.4.1.5003.9.10.1.1.1.7INTEGER {acTDMBusSlaveMode(0), acTDMBusMasterMode(1), acH110BusSecondaryMasterMode(2)}read-writeobsolete
tDMBusNetRefSpeed
OBJECT-TYPE
Determine the NetRef frequency (for both generation and synchronization).
1.3.6.1.4.1.5003.9.10.1.1.1.8INTEGER {acTH110BusNetReferenceSpeed-8khz(0), acTH110BusNetReferenceSpeed-20488khz(2)}read-writeobsolete
tDMBusOutputStartingChannel
OBJECT-TYPE
Defines the outgoing TDM Timeslot of the first channel (ChannelId=0). The remaining channels are organized sequentially.
1.3.6.1.4.1.5003.9.10.1.1.1.9INTEGER (0..127)read-writeobsolete
boardTDMBusOutputPort
OBJECT-TYPE
Defines the SC/MVIP/H.100/H.110 port to be used for board's channel #0. All other channels then occupy the next timeslots sequentially
1.3.6.1.4.1.5003.9.10.1.1.1.10INTEGER (0..31)read-writeobsolete
tDMBusSpeed
OBJECT-TYPE
Selects the TDM Bus Speed. Speed is set according to the Bus Type. The following are allowed speeds for each bus type: SC = 0/2/3 H.110/H.100 = 3 MVIP = 0
1.3.6.1.4.1.5003.9.10.1.1.1.11INTEGER {acTDMBusSpeed-2Mbps(0), acTDMBusSpeed-4Mbps(2), acTDMBusSpeed-8Mbps(3), acTDMBusSpeed-16Mbps(4)}read-writeobsolete
tDMBusType
OBJECT-TYPE
Selects the TDM bus interface to be used (only one TDM bus interface can be enabled at one time although more than one can physically exist on the board).
1.3.6.1.4.1.5003.9.10.1.1.1.12INTEGER {mVIP-BUS(0), sC-BUS(1), uSE-FRAMERS(2), qSLAC-BUS(3), uSE-H110-BUS(4), uSE-EXT-BUS(5), aNALOG-BUS(6), uSE-PSTN-SW-ONLY(8)}read-writeobsolete
acOverrideDefaultIdlePCMPattern
OBJECT-TYPE
Override Default Idle PCM Pattern. 0 - use defaults (0xff-Mulaw, 0x55-Alaw) 1 - use IdlePCMPattern.
1.3.6.1.4.1.5003.9.10.1.1.1.13INTEGER {useDefaults(0), useIdlePCMPattern(1)}read-writeobsolete
acOverrideDefaultIdleABCDPattern
OBJECT-TYPE
Description: Override Default Idle ABCD Pattern. 0 - use defaults (0xf) 1 - use IdleABCDPattern.
1.3.6.1.4.1.5003.9.10.1.1.1.14INTEGER {useDefaults(0), useIdleABCDPattern(1)}read-writeobsolete
networkSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.2
baseUDPPort
OBJECT-TYPE
Lower boundary of UDP ports to be used by the board. The upper boundary is BoardBaseUDPPort+10*(Number of Channels). Must be a multiple of 10.
1.3.6.1.4.1.5003.9.10.1.1.2.1INTEGER (0..64000)read-writeobsolete
defaultGatewayAddr
OBJECT-TYPE
Default Gateway Address. Board's Default Gateway IP address. (in host byte order e.g. 192.10.1.255 = 0xc00a01ff).
1.3.6.1.4.1.5003.9.10.1.1.2.2IpAddressread-onlyobsolete
boardIPAddr
OBJECT-TYPE
Board IP Address. in host byte order e.g. 192.10.1.2 = 0xc00a0102). Users should set the subnet mask to a valid value per the IP address.
1.3.6.1.4.1.5003.9.10.1.1.2.3IpAddressread-onlyobsolete
boardSubNetAddr
OBJECT-TYPE
Board SubNet Address. (in host byte order e.g. 255.255.255.0 = 0xffffff00). default =255.255.255.0.
1.3.6.1.4.1.5003.9.10.1.1.2.4IpAddressread-onlyobsolete
acSyslogServerIP
OBJECT-TYPE
IP address in dotted format notation, e.g., 192.10.1.255
1.3.6.1.4.1.5003.9.10.1.1.2.5IpAddressread-writeobsolete
acMGControlProtocolType
OBJECT-TYPE
This parameter defines the control protocol type 0 = none, 1 = MGCP, 2 = MEGACO, 4 = H323, 8 = SIP
1.3.6.1.4.1.5003.9.10.1.1.2.6INTEGER {controlProtocol-None(0), controlProtocol-MGCP(1), controlProtocol-MEGACO(2), controlProtocol-H323(4), controlProtocol-SIP(8)}read-writeobsolete
acSNMPManagerIP
OBJECT-TYPE
SNMP manager server IP address
1.3.6.1.4.1.5003.9.10.1.1.2.7IpAddressread-writeobsolete
acDisableWEBConfig
OBJECT-TYPE
Enables or disables Web Configuration 0-Read & Write mode(default) 1-Read Only mode
1.3.6.1.4.1.5003.9.10.1.1.2.8INTEGER {enable(0), disable(1)}read-writeobsolete
acEnableSyslog
OBJECT-TYPE
Enable SysLog protocol log.
1.3.6.1.4.1.5003.9.10.1.1.2.9INTEGER {disable(0), enable(1)}read-writeobsolete
acContrlProtocolTransportType
OBJECT-TYPE
Defines the transport type for the control: 0 - UDP, 1 - TCP (SCTP on road map).
1.3.6.1.4.1.5003.9.10.1.1.2.10INTEGER {acCPTransport-UDP-IP(0), acCPTransport-TCP-IP(1), acCPTransport-SCTP-IP(2)}read-writeobsolete
acCPControlDiffServ
OBJECT-TYPE
Defines the value of the 'DiffServ' field in the IP header for the control session.
1.3.6.1.4.1.5003.9.10.1.1.2.11INTEGER (0..63)read-writeobsolete
snmpManagers
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.2.21
snmpManagersTable
OBJECT-TYPE
Snmp Managers Table
1.3.6.1.4.1.5003.9.10.1.1.2.21.1not-accessibleobsolete
snmpManagersEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1not-accessibleobsolete
snmpManagerIndex
OBJECT-TYPE
Snmp Manager Index
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.1INTEGER (0..2)read-onlyobsolete
snmpManagerIsUsed
OBJECT-TYPE
Enable the SNMP Manager to recieve traps.
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.2INTEGER {no(0), yes(1)}read-writeobsolete
snmpManagerIp
OBJECT-TYPE
IP address of default SNMP manager in dotted notation format: xxx.xxx.xxx.xxx. SNMP traps are sent to this manager.
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.3IpAddressread-writeobsolete
snmpManagerTrapPort
OBJECT-TYPE
Sets the trap ports to be used by the different managers.
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.4INTEGER (0..65535)read-writeobsolete
snmpManagerTrapSendingEnable
OBJECT-TYPE
Enable the SNMP Manager to recieve traps.
1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.5INTEGER {disable(0), enable(1)}read-writeobsolete
acNTPSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.2.22
acNTPServerIPAddress
OBJECT-TYPE
NTP Server IP address.
1.3.6.1.4.1.5003.9.10.1.1.2.22.1IpAddressread-writeobsolete
acNTPUtcOffset
OBJECT-TYPE
NTP time to offset in seconds. Default is 0. Range - Between -43200 ot 43200 seconds.
1.3.6.1.4.1.5003.9.10.1.1.2.22.2INTEGER (-43200..43200)read-writedeprecated
acNTPUpdateInterval
OBJECT-TYPE
NTPupdate interval in seconds. Default is 86400 (24 hours). Not recommended to be set beyond one month (2592000 sec).
1.3.6.1.4.1.5003.9.10.1.1.2.22.3INTEGER (0..2147483647)read-writedeprecated
acWEBAccess
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.2.23
acWEBAccessTable
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.2.23.1not-accessibleobsolete
acWEBAccessEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1not-accessibleobsolete
acWEBAccessRowStatus
OBJECT-TYPE
WEB Access row-status
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.1INTEGER (1)read-writeobsolete
acWEBAccessAction
OBJECT-TYPE
WEB Access action
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.2INTEGER (0)read-writeobsolete
acWEBAccessActionResult
OBJECT-TYPE
WEB Access action result
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.3INTEGER (0)read-onlyobsolete
acWEBAccessIndex
OBJECT-TYPE
WEB Access index
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.4INTEGER (0)read-onlyobsolete
acWEBAccessUserName
OBJECT-TYPE
WEB Access user name
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.5OCTET STRING (SIZE(0..26))read-writeobsolete
acWEBAccessUserCode
OBJECT-TYPE
WEB Access user code
1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.6OCTET STRING (SIZE(0..26))read-writeobsolete
auxiliarySettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.3
enableDiagnostics
OBJECT-TYPE
The EnableDiagnostics checks the correct functionality of different hardware components on the board. Upon completion, the board sends EV_END_BIT which contains information on the results of the test of each hardware component.
1.3.6.1.4.1.5003.9.10.1.1.3.1INTEGER {acDiagnostics-Disabled(0), acDiagnostics-BuiltInTest(1), acDiagnostics-BuiltInTestwithPartialFlash(2), acDiagnostics-BuiltInTestWithSDRAM(3)}read-writeobsolete
trunkSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.4
trunkSettingsTable
OBJECT-TYPE
Trunks Table
1.3.6.1.4.1.5003.9.10.1.1.4.1not-accessibleobsolete
trunkSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.4.1.1not-accessibleobsolete
trunkId
OBJECT-TYPE
Trunk ID at board in which the call is taking place
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.1INTEGER (0..32)read-onlyobsolete
clockMaster
OBJECT-TYPE
Selects the trunk clock source. When choosing acCLOCK_MASTER_OFF (= 0) the clock is recovered from the line. When choosing acCLOCK_MASTER_ON (= 1) the trunk clock source is provided by the internal/TDM bus clock source depending on the TDMBusClockSource parameter.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.2INTEGER {acCLOCK-MASTER-OFF(0), acCLOCK-MASTER-ON(1)}read-writeobsolete
framingMethod
OBJECT-TYPE
Selects the Framing method to be used for this trunk.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.3INTEGER {eXTENDED-SUPER-FRAME(0), sUPER-FRAME(1), e1-FRAMING-DDF(2), e1-FRAMING-MFF-CRC4(3), e1-FRAMING-MFF-CRC4-EXT(4), e1-FRAMING-NIL(5), t1-FRAMING-F4(6), t1-FRAMING-F12(7), t1-FRAMING-ESF(8), t1-FRAMING-ESF-CRC6(9), t1-FRAMING-F72(10), t1-FRAMING-ESF-CRC6-JT(11), t1-FRAMING-NIL(12)}read-writeobsolete
protocolType
OBJECT-TYPE
Protocol Type. Sets the PSTN protocol to be used for this trunk. The protocol type parameter defines the interface and the specific telephony protocol. Each protocol defines the following: 1. E1 or T1 physical line configuration. 2. Fixed connection of the relevant time-slots, which are the Trunks' B-channels, mapping to the 60 (128 for TrunkPack®-VoIP/400) DSP channels. This limitation is about to change in versions higher than 3.4. 3. Layer 3 specific telephony protocol or transparent mode of operation. Currently only identical configurations (protocol type, framing method, etc.) for the two trunks are supported.(see at the TrunkPack®-VoIP User Manual for available protocols families) relevant only when TDMBusType=FRAMERS.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.4INTEGER {nONE(0), e1EuroISDN(1), t1Cas(2), t1RawCas(3), t1Transparent(4), e1Transparent31(5), e1Transparent30(6), e1Mfcr2(7), e1CasR2(8), e1RawCAS(9), t1-NI2ISDN(10), t1-4EssISDN(11), t1-5Ess-9-ISDN(12), t1-5Ess-10-ISDN(13), t1-Dms100-ISDN(14), j1-TRANSPARENT(15), pROTOCOL-TYPE-T1-NTT-ISDN(16), pROTOCOL-TYPE-E1-AUSTEL-ISDN(17), pROTOCOL-TYPE-E1-HKT-ISDN(18), pROTOCOL-TYPE-E1-KOR-ISDN(19), pROTOCOL-TYPE-T1-HKT-ISDN(20), pROTOCOL-TYPE-E1-QSIG(21), pROTOCOL-TYPE-E1-TNZ-22(22), pROTOCOL-TYPE-T1-EXTRA-23(23), pROTOCOL-TYPE-V5-1-AN(24), pROTOCOL-TYPE-V5-1-LE(25), pROTOCOL-TYPE-V5-2-AN(26), pROTOCOL-TYPE-V5-2-LE(27), pROTOCOL-TYPE-T1-IUA(28), pROTOCOL-TYPE-E1-IUA(29), pROTOCOL-TYPE-E1-EXTRA-30(30), pROTOCOL-TYPE-E1-EXTRA-31(31), pROTOCOL-TYPE-T1-EXTRA-32(32), pROTOCOL-TYPE-T1-EXTRA-33(33), pROTOCOL-TYPE-T1-EURO-ISDN(34), pROTOCOL-TYPE-T1-DMS100-MERIDIAN-ISDN(35), pROTOCOL-TYPE-T1-NI1-ISDN(36)}read-writeobsolete
terminationSide
OBJECT-TYPE
For ISDN only. select the ISDN Termination side (layer 2)
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.5INTEGER {acUSER-TERMINATION-SIDE(0), acNETWORK-TERMINATION-SIDE(1)}read-writeobsolete
dchConfig
OBJECT-TYPE
Defines D-channel configuration. This setting is only applicable to ISDN PRI protocols that support NFAS and/or D-channel backup procedures.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.6INTEGER {acDCH-CONFIG-PRIMARY(0), acDCH-CONFIG-BACKUP(1), acDCH-CONFIG-NFAS(2), acDCH-NOT-ISDN-TRUNK(3)}read-writeobsolete
lineCode
OBJECT-TYPE
Use to select line code. B8ZS or AMI for T1 spans and HDB3 or AMI for E1 spans.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.7INTEGER {acB8ZS(0), acAMI(1), acHDB3(2)}read-writeobsolete
lineBuildOutLoss
OBJECT-TYPE
Selects the line build out loss to be used for this trunk
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.8INTEGER {ac0DB(0), ac7-5DB(1), ac15DB(2), ac22-5DB(3)}read-writeobsolete
lineBuildOutOverwrite
OBJECT-TYPE
Overwrite the framer's XPM registers values (these registers control the line pulse shape).
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.9INTEGER {acNO-OVER-WRITE(0), acOVER-WRITE(1)}read-writeobsolete
lineBuildOutXPM0
OBJECT-TYPE
Controls the Framer's XPM0 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.10INTEGER (0..255)read-writeobsolete
lineBuildOutXPM1
OBJECT-TYPE
Controls the Framer's XPM1 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert Users.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.11INTEGER (0..255)read-writeobsolete
lineBuildOutXPM2
OBJECT-TYPE
Controls the Framer's XPM2 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.12INTEGER (0..255)read-writeobsolete
traceLevel
OBJECT-TYPE
Defines the Protocol Trace level
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.13INTEGER {acNO-TRACE(0), acFULL-ISDN-TRACE(1), acLAYER3-ISDN-TRACE(2), acONLY-ISDN-Q931-MSGS-TRACE(3), acLAYER3-ISDN-TRACE-NO-DUPLICATION(4), acFULL-ISDN-TRACE-WITH-DUPLICATION(5), acISDN-Q931-RAW-DATA-TRACE(6), acISDN-Q921-RAW-DATA-TRACE(7), acISDN-Q931-Q921-RAW-DATA-TRACE(8), acSS7-MTP2(10), acSS7-MTP2-AND-APPLI(11), acSS7-MTP2-SL-L3-NO-MSU(12), acSS7-AAL(15)}read-writeobsolete
acV5InterfaceTrunkGroupId
OBJECT-TYPE
copy from Table 8-1 in LIB manual 4.2beta
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.14INTEGER (0..31)read-onlyobsolete
acV5LinkIdOld
OBJECT-TYPE
copy from Table 8-1 in LIB manual 4.2beta
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.15INTEGER (0..255)read-writeobsolete
acPMStatus
OBJECT-TYPE
performance Monitoring Enable/Disable.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.16INTEGER {disable(0), enable(1)}read-writeobsolete
acLedStatusColor
OBJECT-TYPE
Trunk led status color
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.17INTEGER {off(0), red(1), green(2)}read-onlyobsolete
acLedStatusRate
OBJECT-TYPE
Trunk led status blinking rate
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.18INTEGER {steady(0), blink(1)}read-onlyobsolete
acIsdnNfasInterfaceId
OBJECT-TYPE
Defines the Interface ID works with NS_EXPLICIT_INTERFACE_ID bit. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.19INTEGER (0..255)read-writeobsolete
acTrunkCasTableIndex
OBJECT-TYPE
Index of Cas Table used by this Trunk
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.20INTEGER (0..7)read-writeobsolete
acTrunkAdminState
OBJECT-TYPE
Trunk Administrative State
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.21INTEGER {lock(0), unLock(1)}read-writeobsolete
acPSTNIuaInterfaceId
OBJECT-TYPE
IUA trunk interface ID value
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.22INTEGER (-1..2147483647)read-writeobsolete
acIsdnQ931LayerResponseBehavior
OBJECT-TYPE
Bit-field used to determine several behavior options, which influence how the Q.931 protocol behaves.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.23INTEGER (-2147483647..2147483647)read-writeobsolete
acIsdnIncomingCallsBehavior
OBJECT-TYPE
This is the bit-field used to determine several behavior options that influence how the ISDN Stack INCOMING calls behave. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.24INTEGER (0..2147483647)read-writeobsolete
acIsdnOutgoingCallsBehavior
OBJECT-TYPE
This is the bit-field used to determine several behavior options that influence how the ISDN Stack OUTGOING calls behave. Refer to Appendix A.8 in the 'VoPLib Reference Library User's Manual.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.25INTEGER (0..65535)read-writeobsolete
acIsdnGeneralCCBehavior
OBJECT-TYPE
This is the bit-field used to determine several general ISDN behavior options. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.26INTEGER (0..65535)read-writeobsolete
acIsdnNfasGroupNumber
OBJECT-TYPE
Relevant only for T1 ISDN NFAS trunks indicates the group number of the NFAS group. ;Valid NFAS group numbers are only 1 to 4, 0 indicating that this trunk is not NFAS (in this case the ISDNNFASInterfaceID and DchConfig parameters are ignored).
1.3.6.1.4.1.5003.9.10.1.1.4.1.1.27INTEGER (0..4)read-writeobsolete
mGCPSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.5
callAgentIP
OBJECT-TYPE
MGCP Call Agent IP address to be used for the initial RestartInProgress MGCP message (RSIP) (e.g., 192.10.1.255). Set to 0.0.0.0 to avoid sending RSIP. This parameter if in use overrides the Call Agent IP address provided in BootP.
1.3.6.1.4.1.5003.9.10.1.1.5.1IpAddressread-writeobsolete
callAgentPort
OBJECT-TYPE
Gate Way will use CallAgentPort as default UDP Port of MGCP Call Agent.
1.3.6.1.4.1.5003.9.10.1.1.5.2INTEGER (0..65534)read-writeobsolete
callAgentDomainName
OBJECT-TYPE
MGCP Call Agent domain name.
1.3.6.1.4.1.5003.9.10.1.1.5.3OCTET STRING (SIZE(0..64))read-writeobsolete
redundantAgentIP
OBJECT-TYPE
Redundant MGCP call agent IP address for initial RestartInProgress MGCP message (RSIP) e.g. 192.10.1.255. Set to 0 to avoid sending RSIP.
1.3.6.1.4.1.5003.9.10.1.1.5.4IpAddressread-writeobsolete
redundantAgentPort
OBJECT-TYPE
UDP Port of Redundant MGCP call agent.
1.3.6.1.4.1.5003.9.10.1.1.5.5INTEGER (0..65534)read-writeobsolete
redundantCallAgentDomainName
OBJECT-TYPE
Redundant MGCP Call Agent Domain name
1.3.6.1.4.1.5003.9.10.1.1.5.6OCTET STRING (SIZE(0..64))read-writeobsolete
dePopulatedChannelsNumber
OBJECT-TYPE
This parameter can be used to enable MGCP call agent to access only subset of the on board channel bank. Set to -1 (or do not specify) to use all channels.
1.3.6.1.4.1.5003.9.10.1.1.5.7INTEGER (-1..2147483647)read-writeobsolete
gateWayName
OBJECT-TYPE
GateWay Name
1.3.6.1.4.1.5003.9.10.1.1.5.8OCTET STRING (SIZE(0..64))read-writeobsolete
endPointName
OBJECT-TYPE
MGCP: Gateway's end point name. This is a prefix used to identify the endpoint, i.e., 'ACgw' in the following example: 'ACgw5@acl.com'. MEGACO: Prefix of the endpoint part of the termination name
1.3.6.1.4.1.5003.9.10.1.1.5.9OCTET STRING (SIZE(0..20))read-writeobsolete
mGCPCommunicationLayerTimeout
OBJECT-TYPE
Assumed delay of the communication layer. It is used in retransmission.
1.3.6.1.4.1.5003.9.10.1.1.5.10INTEGER (0..999)read-writeobsolete
acDefaultChannelSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.6
acChDefaultDJBufMinDelay
OBJECT-TYPE
Dynamic Jitter Buffer Minimum Delay (msec)
1.3.6.1.4.1.5003.9.10.1.1.6.1INTEGER (0..150)read-writeobsolete
acChDefaultDJBufOptFactor
OBJECT-TYPE
Dynamic Jitter Buffer frame error/delay optimization.
1.3.6.1.4.1.5003.9.10.1.1.6.2INTEGER (0..13)read-writeobsolete
acChDefaultCallerIDType
OBJECT-TYPE
The supported caller ID standard types
1.3.6.1.4.1.5003.9.10.1.1.6.3INTEGER {callerIDStandard-Bellcore(0), callerIDStandard-ETSI(1), callerIDStandard-NTT(2), callerIDStandard-DTMF-Based-ETSI(16), callerIDStandard-Denmark(17), callerIDStandard-Indian(18)}read-writeobsolete
acChDefaultFaxModemBypassM
OBJECT-TYPE
Number of basic frames to generating one RTP fax/modem bypass packet.
1.3.6.1.4.1.5003.9.10.1.1.6.4INTEGER (1..12)read-writeobsolete
acChDefaultFaxModemRelayVolume
OBJECT-TYPE
Fax gain control. The range -18 to -3 relates to -18.5 dBm to -3.5 dBm in 1 dBm steps.
1.3.6.1.4.1.5003.9.10.1.1.6.5INTEGER (-18..-3)read-writeobsolete
acChDefaultFaxRelayECMEnable
OBJECT-TYPE
Enables or disables the using of ECM mode during Fax Relay.
1.3.6.1.4.1.5003.9.10.1.1.6.6INTEGER {disable(0), enable(1)}read-writeobsolete
acChDefaultFaxRelayMaxRate
OBJECT-TYPE
Limits the maximum rate at which fax messages are transmitted.
1.3.6.1.4.1.5003.9.10.1.1.6.7INTEGER {acRate2400bps(0), acRate4800bps(1), acRate7200bps(2), acRate9600bps(3), acRate12000bps(4), acRate14400bps(5)}read-writeobsolete
acChDefaultFaxTransportMode
OBJECT-TYPE
Sets the Fax over IP transport method.
1.3.6.1.4.1.5003.9.10.1.1.6.8INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultModemRelayRedundancyDepth
OBJECT-TYPE
Amount of redundancy for fax relay packets
1.3.6.1.4.1.5003.9.10.1.1.6.9INTEGER {disable(0), enable(1)}read-writeobsolete
acChDefaultModemRelayMaxRate
OBJECT-TYPE
Default: Modem Relay Max Rate
1.3.6.1.4.1.5003.9.10.1.1.6.10INTEGER {ac2400(0), ac4800(1), ac7200(2), ac9600(3), ac12000(4), ac14400(5)}read-writeobsolete
acChDefaultUseT38orFRF11
OBJECT-TYPE
Selects protocol to send/ receive fax relay.
1.3.6.1.4.1.5003.9.10.1.1.6.11INTEGER {fRF11(0), acT38(1)}read-writeobsolete
acChDefaultV21ModemTransportType
OBJECT-TYPE
Sets the V.21 modem transport method (must be set to 0 = disable)
1.3.6.1.4.1.5003.9.10.1.1.6.12INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultV22ModemTransportType
OBJECT-TYPE
Sets the V.22 modem transport method
1.3.6.1.4.1.5003.9.10.1.1.6.13INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultV23ModemTransportType
OBJECT-TYPE
Sets the V.23 modem transport method
1.3.6.1.4.1.5003.9.10.1.1.6.14INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultV32ModemTransportType
OBJECT-TYPE
Sets the V.32 modem transport method
1.3.6.1.4.1.5003.9.10.1.1.6.15INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultV34ModemTransportType
OBJECT-TYPE
Sets the V.34 modem transport method
1.3.6.1.4.1.5003.9.10.1.1.6.16INTEGER {disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)}read-writeobsolete
acChDefaultFaxModemBypassCoderType
OBJECT-TYPE
The User can set the bypass coder (according to the known coders)
1.3.6.1.4.1.5003.9.10.1.1.6.17INTEGER {g711Alaw-64(0), g711Mulaw(1), g726-32(4), g726-40(5)}read-writeobsolete
acChDefaultFaxRelayRedundancyDepth
OBJECT-TYPE
Default: Fax Relay Redundancy Depth. Number of repetitions to be applied to each fax relay payload when transmitting to network.
1.3.6.1.4.1.5003.9.10.1.1.6.18INTEGER (0..2)read-writeobsolete
acChDefaultT38ProtectionMode
OBJECT-TYPE
Default: T38 Protection Mode. Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.
1.3.6.1.4.1.5003.9.10.1.1.6.19INTEGER {redundancyPackets(0), fEC(1)}read-writeobsolete
acChDefaultDTMFVolume
OBJECT-TYPE
DTMF generation Volume Control
1.3.6.1.4.1.5003.9.10.1.1.6.20INTEGER (-31..0)read-writeobsolete
acChDefaultDTMFTransportType
OBJECT-TYPE
0 = Mute = erases digit from voice stream does not relay to remote. 2 = Transparent = digits remains in voice stream. 3 = RFC 2833 relay = erase digit from voice stream relay to remote using RFC 2833 syntax. The other values as seen in the Value List (1 and 7) are not supported as of version 4.4.
1.3.6.1.4.1.5003.9.10.1.1.6.21INTEGER {acMuteDTMF(0), acRelayDTMF(1), acTransparentDTMF(2), acRFC2833RalayDTMF(3), acRFC2833RelayDecoderMute(7)}read-writeobsolete
acChDefaultMFTransportType
OBJECT-TYPE
0 = erase MFs from voice transport not relayed to remote. 2 = MFs not erased not relayed to remote. 3 = MFs are muted from the voice stream & relayed according to RFC 2833.
1.3.6.1.4.1.5003.9.10.1.1.6.22INTEGER {acMuteMF(0), acRelayMF(1), acTransparentMF(2), acRFC2833RalayMF(3)}read-writeobsolete
acChDefaultInputGain
OBJECT-TYPE
PCM input gain. The range is 31 dB to +31 dB in 1 dB steps.
1.3.6.1.4.1.5003.9.10.1.1.6.23INTEGER (-32..31)read-writeobsolete
acChDefaultRTPRedundancyDepth
OBJECT-TYPE
Enables or disables generation of RFC 2198 redundancy packets.
1.3.6.1.4.1.5003.9.10.1.1.6.24INTEGER {disable(0), enable(1)}read-writeobsolete
acChDefaultTestMode
OBJECT-TYPE
Testing mode applied. 0 = Coder Loopback performs an encoder/decoder loopback inside DSP device. 1 = PCMLoopback loops back incoming PCM to the outgoing PCM. 2 = ToneInjection generates a 1000 Hz tone to outgoing PCM. 3 = NoLoopback sets the channel to work in normal mode.
1.3.6.1.4.1.5003.9.10.1.1.6.25INTEGER {coderLoopback(0), pCMLoopback(1), toneInjection(2), noLoopback(3)}read-writeobsolete
acChDefaultVoiceVolume
OBJECT-TYPE
Voice output gain control the range is -31 dB to +31 dB in 1 dB steps -32 = mute.
1.3.6.1.4.1.5003.9.10.1.1.6.26INTEGER (-32..31)read-writeobsolete
acChDefaultM
OBJECT-TYPE
Number of DSP payloads for generating one RTP packet
1.3.6.1.4.1.5003.9.10.1.1.6.27INTEGER (1..12)read-writeobsolete
acChDefaultFlashHookPeriod
OBJECT-TYPE
Flash hook period.
1.3.6.1.4.1.5003.9.10.1.1.6.28INTEGER (0..65535)read-writeobsolete
acChDefaultDTMFDetectionPoint
OBJECT-TYPE
Defines if the detection of DTMF events is notified at the end of DTMF or at the start of DTMF.
1.3.6.1.4.1.5003.9.10.1.1.6.29INTEGER (0..1)read-writeobsolete
acChDefaultRtpIpTos
OBJECT-TYPE
Sets value of IP Type Of Service field in IP header for all packets generated from this channel. Follow the acTIPTOS enumeration.
1.3.6.1.4.1.5003.9.10.1.1.6.30INTEGER (0..15)read-writeobsolete
acChDefaultRtpIpPrecedence
OBJECT-TYPE
Sets value of the IP precedence field in the IP header for all packets generated from this channel. Follow the acTIPPrecedence enumeration.
1.3.6.1.4.1.5003.9.10.1.1.6.31INTEGER (0..7)read-writeobsolete
acChDefaultEchoCancler
OBJECT-TYPE
Controls the activation of the Echo Canceler (refer also to 'ForceEchoOff')
1.3.6.1.4.1.5003.9.10.1.1.6.32INTEGER {disable(0), enable(1)}read-writeobsolete
acChDefaultSilenceSuppression
OBJECT-TYPE
Silence Suppression mode
1.3.6.1.4.1.5003.9.10.1.1.6.33INTEGER {sILENCE-COMPRESION-DISABLE(0), sILENCE-COMPRESION-ENABLE(1), sILENCE-COMPRESION-ENABLE-NOISE-ADAPTATION-DISABLE(2)}read-writeobsolete
acChDefaultEchoCanclerHybridLoss
OBJECT-TYPE
Sets worst case ratio between signal level transmitted to hybrid & echo level returning from hybrid. Set this per worst hybrid in the system in terms of echo return loss. Refer to acTECHybridLoss enumeration:
1.3.6.1.4.1.5003.9.10.1.1.6.34INTEGER {eCHybridLoss6DBM(0), eCHybridLoss9DBM(1), eCHybridLoss0DBM(2), eCHybridLoss3DBM(3)}read-writeobsolete
acChDefaultPacketizationPeriod
OBJECT-TYPE
Packetization Period
1.3.6.1.4.1.5003.9.10.1.1.6.35INTEGER (5..80)read-writeobsolete
aTMSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.7
vPMask
OBJECT-TYPE
VP masking bits used for address resolution
1.3.6.1.4.1.5003.9.10.1.1.7.1INTEGER (0..255)read-writeobsolete
vCMask
OBJECT-TYPE
VC masking bits used for address resolution
1.3.6.1.4.1.5003.9.10.1.1.7.2INTEGER (0..2147483647)read-writeobsolete
externalClk
OBJECT-TYPE
Source clock of on the board UTOPIA bus
1.3.6.1.4.1.5003.9.10.1.1.7.3INTEGER {acATMUtopiaInternalClock(0), acATMUtopiaExternalClock(1)}read-writeobsolete
aTMLoopBack
OBJECT-TYPE
Phy loopback. The loopback can be used for testing purposes. The loopback direction is towards the PSTN side
1.3.6.1.4.1.5003.9.10.1.1.7.4INTEGER {loopbackDisabled(0), loopbackEnabled(1)}read-writeobsolete
utopiaSlave
OBJECT-TYPE
UTOPIA interface mode of bus arbitration
1.3.6.1.4.1.5003.9.10.1.1.7.5INTEGER {aTM-UTOPIA-MASTER(0), aTM-UTOPIA-SLAVE(1)}read-writeobsolete
multyPhy
OBJECT-TYPE
UTOPIA interface SinglePhy or MultiPhy mode
1.3.6.1.4.1.5003.9.10.1.1.7.6INTEGER {singlePhy(0), multiPhy(1)}read-writeobsolete
slavePhyNum
OBJECT-TYPE
Provides the slave number for this device (board) in the UTOPIA system bus (Applies to slave mode only)
1.3.6.1.4.1.5003.9.10.1.1.7.7INTEGER (-1..31)read-writeobsolete
utopiaBus16
OBJECT-TYPE
UTOPIA interface mode of bus width
1.3.6.1.4.1.5003.9.10.1.1.7.8INTEGER {acATMUtopiaBusWidth16bit(0), acATMUtopiaBusWidth8bit(1)}read-writeobsolete
aTMPHYType
OBJECT-TYPE
External interface type of the board
1.3.6.1.4.1.5003.9.10.1.1.7.9INTEGER {acOC3(0), acUtopia(1)}read-writeobsolete
disablePayloadScrambling
OBJECT-TYPE
Disable/Enable Cell payload scrambling in the ATM PHY
1.3.6.1.4.1.5003.9.10.1.1.7.10INTEGER {enable(0), disable(1)}read-writeobsolete
pHYClkSource
OBJECT-TYPE
OC3 Tx clock source
1.3.6.1.4.1.5003.9.10.1.1.7.11INTEGER {acPhyInternalClock(0), acPhyExternalClock(1)}read-writeobsolete
sendIdleCASUponLinkFail
OBJECT-TYPE
This I.366.2 allows sending a special idle CAS packet which signals that the other side has a failure
1.3.6.1.4.1.5003.9.10.1.1.7.12INTEGER {acATMSendIdleCASUponLinkFail-Disabled(0), acATMSendIdleCASUponLinkFail-Enabled(1)}read-writeobsolete
masterSlaveMode
OBJECT-TYPE
Loop Emulation Mode (vmoa145) Master/Slave mode
1.3.6.1.4.1.5003.9.10.1.1.7.13INTEGER {acATM-MasterMode-CO-IWF(0), acATM-SlaveMode-CP-IWF(1)}read-writeobsolete
vccProfile
OBJECT-TYPE
Determine the required combination of Board's maximal number of VCC and maximal number of channels per VCC
1.3.6.1.4.1.5003.9.10.1.1.7.14INTEGER {ac240VCCs-8CIDsperVCC(0), ac105VCCs-24CIDsperVCC(1), ac84VCCs-32CIDsperVCC(2), ac14VCCs-240CIDsperVCC(3)}read-writeobsolete
tPNCPVPI
OBJECT-TYPE
VPI used for transferring TPNCP command over AAL5 transport layer
1.3.6.1.4.1.5003.9.10.1.1.7.15INTEGER (0..2147483647)read-writeobsolete
tPNCPVCI
OBJECT-TYPE
VCI used for transferring TPNCP command over AAL5 transport layer
1.3.6.1.4.1.5003.9.10.1.1.7.16INTEGER (0..2147483647)read-writeobsolete
sAALLink0VPI
OBJECT-TYPE
VPI of the 1st SAAL link (number 0)
1.3.6.1.4.1.5003.9.10.1.1.7.17INTEGER (0..2147483647)read-writeobsolete
sAALLink0VCI
OBJECT-TYPE
VCI of the 1st SAAL link (number 0)
1.3.6.1.4.1.5003.9.10.1.1.7.18INTEGER (0..2147483647)read-writeobsolete
sAALLink1VPI
OBJECT-TYPE
VPI of the 2nd SAAL link (number 1)
1.3.6.1.4.1.5003.9.10.1.1.7.19INTEGER (0..2147483647)read-writeobsolete
sAALLink1VCI
OBJECT-TYPE
VCI of the 1st SAAL link (number 1)
1.3.6.1.4.1.5003.9.10.1.1.7.20INTEGER (0..2147483647)read-writeobsolete
acSS7Settings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.8
acSS7SettingsTable
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.8.1not-accessibleobsolete
acSS7SettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.8.1.1not-accessibleobsolete
acSS7LinkId
OBJECT-TYPE
SS7 Link Id.
1.3.6.1.4.1.5003.9.10.1.1.8.1.1.1INTEGER (0..8)read-writeobsolete
acSS7traceLevel
OBJECT-TYPE
.
1.3.6.1.4.1.5003.9.10.1.1.8.1.1.2INTEGER {acNO-TRACE(0), acFULL-TRACE(1), acISDN-IUA-TRACE(9), acSS7-MTP2(10), acSS7-MTP2-AND-APPLI(11), acSS7-MTP2-SL-L3-NO-MSU(12), acSS7-AAL(15)}read-writeobsolete
acConfigFiles
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.11
acFxsCoefficients
OBJECT-TYPE
The FXS coefficient file name.
1.3.6.1.4.1.5003.9.10.1.1.11.1OCTET STRING (SIZE(0..255))read-onlyobsolete
acFxoCoefficients
OBJECT-TYPE
The FXO coefficient file name.
1.3.6.1.4.1.5003.9.10.1.1.11.2OCTET STRING (SIZE(0..255))read-onlyobsolete
acCptFile
OBJECT-TYPE
.
1.3.6.1.4.1.5003.9.10.1.1.11.3OCTET STRING (SIZE(0..255))read-onlyobsolete
acVpFile
OBJECT-TYPE
The name (and path) of the file containing the voice prompts
1.3.6.1.4.1.5003.9.10.1.1.11.4OCTET STRING (SIZE(0..255))read-onlyobsolete
acCasTables
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.11.21
acCasTablesTable
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.11.21.1not-accessibleobsolete
acCasTablesEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1not-accessibleobsolete
acCasTableIndex
OBJECT-TYPE
Cas Table Indexd
1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.1INTEGER (0..7)read-onlyobsolete
acCasTabeName
OBJECT-TYPE
Cas Table Name
1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.2OCTET STRING (SIZE(0..255))read-onlyobsolete
acFxs
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.12
acPolarityReversalType
OBJECT-TYPE
Sets the type of the polarity reversal signal used for the network far-end answer and disconnect indications. Smooth reversal prevents negative effects as non-required ringing.
1.3.6.1.4.1.5003.9.10.1.1.12.1INTEGER {soft(0), hard(1)}read-writeobsolete
megacoSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.13
megacoCurrentProfile
OBJECT-TYPE
Use this parameter to MGCP/MEGACO beheviour for specific compatibility. See user manual.
1.3.6.1.4.1.5003.9.10.1.1.13.1INTEGER (1..8191)read-writeobsolete
megacoGatewayName
OBJECT-TYPE
MGCP:Gateway's identification name towards the MGCP Call Agent. If empty Gateway name holds the IP address of the board MEGACO: Prefix of the gateway part of the termination name
1.3.6.1.4.1.5003.9.10.1.1.13.2OCTET STRING (SIZE(0..64))read-writeobsolete
megacoEndpointName
OBJECT-TYPE
Megaco Endpoint Name
1.3.6.1.4.1.5003.9.10.1.1.13.3OCTET STRING (SIZE(0..20))read-writeobsolete
megacoTrunkName
OBJECT-TYPE
MGCP: Together with 'EndpointPrefix' field generates local endpoint name on trunk enabled gateways MEGACO: Prefix of the trunk part of the termination name
1.3.6.1.4.1.5003.9.10.1.1.13.4OCTET STRING (SIZE(0..20))read-writeobsolete
megacoActiveCallAgentIp
OBJECT-TYPE
Megaco Active Call Agent
1.3.6.1.4.1.5003.9.10.1.1.13.5OCTET STRING (SIZE(0..20))read-onlyobsolete
megacoActiveCallAgentPort
OBJECT-TYPE
Megaco Active Port
1.3.6.1.4.1.5003.9.10.1.1.13.6INTEGER (0..32767)read-onlyobsolete
megacoCallAgents
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.13.7
megacoCallAgentsTable
OBJECT-TYPE
Magaco Call agents Table
1.3.6.1.4.1.5003.9.10.1.1.13.7.1not-accessibleobsolete
megacoCallAgentsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1not-accessibleobsolete
megacoCallAgentId
OBJECT-TYPE
Megaco Call Agent Id
1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.1INTEGER (0..4)read-onlyobsolete
megacoCallAgentIp
OBJECT-TYPE
Megaco CallAgent IP
1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.2OCTET STRING (SIZE(0..20))read-writeobsolete
megacoCallAgentPort
OBJECT-TYPE
List of up to 10 UDP Ports of MEGACO Call Agent separated by , or ;.
1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.3INTEGER (0..32767)read-writeobsolete
megacoCallAgentIsUsed
OBJECT-TYPE
Is this index used
1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.4INTEGER {no(0), yes(1)}read-writeobsolete
megacoCheckLegalityOfMGC
OBJECT-TYPE
This parameter specified if the MEGACO will reject commands from an MGC not in the provisioned list
1.3.6.1.4.1.5003.9.10.1.1.13.8INTEGER {disable(0), enable(1)}read-writeobsolete
acPSTNParameters
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.14
acQ931RELAYMODE
OBJECT-TYPE
ISDN level 3 mode
1.3.6.1.4.1.5003.9.10.1.1.14.1INTEGER {none(0), activateLAPDmessaging(1), layer3-IS-IUA(3)}read-writeobsolete
acIsdnDuplicateQ931BuffMode
OBJECT-TYPE
Activates / de-activates delivery of raw Q.931 messages. This Object is obsolete and is replaces by acTrunkISDNCommonDuplicateQ931BuffMode in the acPSTN-MIB.
1.3.6.1.4.1.5003.9.10.1.1.14.2INTEGER (0..255)read-writeobsolete
acPSTNCASTableNum
OBJECT-TYPE
Indicates how many CAS protocol configuration files are loaded, when 0 is no CAS table. It should match the number of fields.
1.3.6.1.4.1.5003.9.10.1.1.14.3INTEGER (0..8)read-onlyobsolete
aMsConfiguration
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.51
amsNumOfConferencePorts
OBJECT-TYPE
Number Of Conference ports. How many ports on the TPM are allocated to the conferencing service.
1.3.6.1.4.1.5003.9.10.1.1.51.1INTEGER (0..480)read-writeobsolete
amsNumOfTestTrunkPorts
OBJECT-TYPE
Number Of Test Trunk ports. How many ports on the TPM are allocated to the Test Trunk service.
1.3.6.1.4.1.5003.9.10.1.1.51.2INTEGER (0..480)read-writeobsolete
amsNumOfLawfulInterceptPorts
OBJECT-TYPE
Number Of Test Trunk ports. How many ports on the TPM are allocated to the Lawful Intercept service.
1.3.6.1.4.1.5003.9.10.1.1.51.3INTEGER (0..480)read-writeobsolete
amsNumOfAnnouncementPorts
OBJECT-TYPE
Number Of Test Trunk ports. How many ports on the TPM are allocated to the Announcement service.
1.3.6.1.4.1.5003.9.10.1.1.51.4INTEGER (0..480)read-writeobsolete
amsApsIpAddress
OBJECT-TYPE
Sets the destination IP to which the heartbeat packets are sent.
1.3.6.1.4.1.5003.9.10.1.1.51.5IpAddressread-writeobsolete
amsApsPort
OBJECT-TYPE
Sets the destination UDP port to which the heartbeat packets are sent.
1.3.6.1.4.1.5003.9.10.1.1.51.6INTEGER (0..64000)read-writeobsolete
amsPrimaryLanguage
OBJECT-TYPE
Primary Language
1.3.6.1.4.1.5003.9.10.1.1.51.7INTEGER {amsLangBelgianDutch(0), amsLangCantonese(1), isoLangEnglish(2), isoLangFrench(3), isoLangGerman(4), isoLangItalian(5), isoLangJapanese(6), isoLangKorean(7), isoLangMalay(8), isoLangMandarin(9), isoLangDutch(10), isoLangPortuguese(11), isoLangSpanish(12), isoLangTagalog(13), isoLangThai(14), isoLangBasque(15), isoLangCatalan(16), isoLangGallegan(17), isoLangHebrew(18), isoLangCzech(19), isoLangGreek(20), isoLangTurkish(21), isoLangVietnamese(22), amsLangBad(100)}read-writeobsolete
amsSecondaryLanguage
OBJECT-TYPE
Secondary Language
1.3.6.1.4.1.5003.9.10.1.1.51.8INTEGER {amsLangBelgianDutch(0), amsLangCantonese(1), isoLangEnglish(2), isoLangFrench(3), isoLangGerman(4), isoLangItalian(5), isoLangJapanese(6), isoLangKorean(7), isoLangMalay(8), isoLangMandarin(9), isoLangDutch(10), isoLangPortuguese(11), isoLangSpanish(12), isoLangTagalog(13), isoLangThai(14), isoLangBasque(15), isoLangCatalan(16), isoLangGallegan(17), isoLangHebrew(18), isoLangCzech(19), isoLangGreek(20), isoLangTurkish(21), isoLangVietnamese(22), amsLangBad(100)}read-writeobsolete
amsProfile
OBJECT-TYPE
AMS Profile Bit Mask: 1'st bit - APS Audio Enable/Disable 2'nd bit - Trunks Interface On/Off 3'td bit - Board Operation State change on ATM Port failure Enable/Disable.
1.3.6.1.4.1.5003.9.10.1.1.51.9INTEGER (0..32)read-writeobsolete
amsAASPackagesProfile
OBJECT-TYPE
.
1.3.6.1.4.1.5003.9.10.1.1.51.10INTEGER {td5Starndard(0), h2489Standard(1)}read-writeobsolete
acFeatureKey
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.90
acFeatureKeyString
OBJECT-TYPE
Coded Key specific for board and required features.
1.3.6.1.4.1.5003.9.10.1.1.90.1OCTET STRING (SIZE(0..256))read-writeobsolete
acActiveFeaturesList
OBJECT-TYPE
List of all avtivated features.
1.3.6.1.4.1.5003.9.10.1.1.90.2OCTET STRING (SIZE(0..484))read-onlyobsolete
supplementary
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.1.99
supplementaryField
OBJECT-TYPE
Flexible INI file line.
1.3.6.1.4.1.5003.9.10.1.1.99.1OCTET STRING (SIZE(0..255))read-writeobsolete
boardInformation
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.2
boardType
OBJECT-TYPE
The type of the Board.
1.3.6.1.4.1.5003.9.10.1.2.1INTEGER {unKnownBoard(0), tP-08(1), mEDIAPACK-108(2), mEDIAPACK-124(3), tP-240(8), tP-610-CL120(10), tP-600(11), tP-600-IPMEDIA(12), tP-9800-C(13), tPM800(16), tPM800-RDK(17), tPM800B(18), tPM800B-RDK(19), tP1600(20), tP-240-IpMedia(21), tPM1100(22), trunkPack-260-IpMedia(23), tP1610(24), mP-104(25), mP-102(26), tP-04(27), tP-02(28), tP-1610-SB(29), tP-1610-IpMedia(30), tP-MEDIANT2000(31), tP-STRETTO2000(32), tP-IPMServer2000(33), tP-2810(34), tP-260-UN-IpMedia(35), tP-260-IpMedia-30Ch(36), tP-260-IpMedia-60Ch(37), tP-260-IpMedia-120Ch(38), tP-260RT-IpMedia-30Ch(39), tP-260RT-IpMedia-60Ch(40), tP-260RT-IpMedia-120Ch(41), tP-260(42), tP-260-UN(43), tPM1100-PCM(44), tP-6310(45), tPM6300(46), mediant1000(47), ipMedia3000(48), mediant3000(49), stretto3000(50), tP-6310-IpMedia(51), tP-6310-SB(52), aTP-1610(53), aTP-260(54), aTP-260-UN(55), mP-118(56)}read-onlyobsolete
boardName
OBJECT-TYPE
The name fo the board
1.3.6.1.4.1.5003.9.10.1.2.2OCTET STRING (SIZE(0..20))read-onlyobsolete
serialNum
OBJECT-TYPE
serial number of board.
1.3.6.1.4.1.5003.9.10.1.2.3INTEGER (0..2147483647)read-onlyobsolete
dSPCount
OBJECT-TYPE
DSP Count
1.3.6.1.4.1.5003.9.10.1.2.4INTEGER (0..2147483647)read-onlyobsolete
channelsCount
OBJECT-TYPE
Channel Count.
1.3.6.1.4.1.5003.9.10.1.2.5INTEGER (0..2147483647)read-onlyobsolete
cPUSpeed
OBJECT-TYPE
CPU Speed
1.3.6.1.4.1.5003.9.10.1.2.6INTEGER (0..2147483647)read-onlyobsolete
softwareVersion
OBJECT-TYPE
TrunkPack Software Version
1.3.6.1.4.1.5003.9.10.1.2.7OCTET STRING (SIZE(0..20))read-onlyobsolete
trunkPackSoftwareDate
OBJECT-TYPE
TrunkPack Software Date
1.3.6.1.4.1.5003.9.10.1.2.8OCTET STRING (SIZE(0..40))read-onlyobsolete
slotNumber
OBJECT-TYPE
Slot number
1.3.6.1.4.1.5003.9.10.1.2.9INTEGER (0..2147483647)read-onlyobsolete
iniFileVersion
OBJECT-TYPE
Ini file version.
1.3.6.1.4.1.5003.9.10.1.2.10INTEGER (0..2147483647)read-onlyobsolete
acDspType
OBJECT-TYPE
Dsp Type
1.3.6.1.4.1.5003.9.10.1.2.11INTEGER (0..2147483647)read-onlyobsolete
acFlashVersion
OBJECT-TYPE
Flash [BootLoader] Version.
1.3.6.1.4.1.5003.9.10.1.2.12INTEGER (0..2147483647)read-onlyobsolete
acBoardFxsOrFxo
OBJECT-TYPE
Board is Fxs Or Fxo
1.3.6.1.4.1.5003.9.10.1.2.13INTEGER {fXO(0), fXS(1)}read-onlyobsolete
acTrunkslCount
OBJECT-TYPE
Trunks Count.
1.3.6.1.4.1.5003.9.10.1.2.14INTEGER (0..2147483647)read-onlyobsolete
acDspVersionTemplate
OBJECT-TYPE
selects the DSP load number, which defines the supported set of coders. Default=0 Each template assigns a specific version to each DSP. Each DSP version supports a set of coders and features. The number of channels supported by the DSP can also vary between DSP versions. The total number of channels supported by the board depends on the selected template.
1.3.6.1.4.1.5003.9.10.1.2.15INTEGER (0..2147483647)read-onlyobsolete
acFirstPortDuplexMode
OBJECT-TYPE
full-duplex or half-duplex connection
1.3.6.1.4.1.5003.9.10.1.2.16INTEGER {halfDuplex(0), fullDuplex(1), forceModeValue(2), notAvailable(3)}read-onlyobsolete
acFirstPortSpeed
OBJECT-TYPE
.
1.3.6.1.4.1.5003.9.10.1.2.17INTEGER {forceModeValue(2), notAvailable(3), ac10Mbps(10), ac100Mbps(100)}read-onlyobsolete
acMeanFreeChannels
OBJECT-TYPE
Mean of Free Channels
1.3.6.1.4.1.5003.9.10.1.2.18INTEGER (0..2147483647)read-onlyobsolete
acMaxFreeChannels
OBJECT-TYPE
Max of Free Channels
1.3.6.1.4.1.5003.9.10.1.2.19INTEGER (0..2147483647)read-onlyobsolete
acSysUpTime
OBJECT-TYPE
Time (in Seconds) that the board is alive.
1.3.6.1.4.1.5003.9.10.1.2.20INTEGER (0..2147483647)read-onlyobsolete
acPhysicalModCount
OBJECT-TYPE
.
1.3.6.1.4.1.5003.9.10.1.2.21INTEGER {soloist(0), second(1), first(2)}read-onlyobsolete
acBoardTemperature
OBJECT-TYPE
Temperature of the board in degrees Celsius, should not go higher then 60!
1.3.6.1.4.1.5003.9.10.1.2.22INTEGER (0..100)read-onlyobsolete
channelConfiguration
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3
voiceSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.2
voiceSettingsTable
OBJECT-TYPE
Data in voice SettingsTable uniquely identify a voice parameters of channel.
1.3.6.1.4.1.5003.9.10.1.3.2.1not-accessibleobsolete
voiceSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.2.1.1not-accessibleobsolete
cID
OBJECT-TYPE
Channel ID
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.1INTEGER (0..2147483647)read-onlydeprecated
coder
OBJECT-TYPE
Digital voice coder
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.2INTEGER {g711Alaw(0), g711Mulaw(1), g726-16(2), g726-24(3), g726-32(4), g726-40(5), g727-16(6), g727-24-16(7), g727-24(8), g727-32-16(9), g727-32-24(10), g727-32(11), g727-40-16(12), g727-40-24(13), g727-40-32(14), g723Low(15), g723High(16), g729(17), gSM(19), gSM610MS(20), transparent(22), g728(23), hDLCCoder(24), netCoder-4-8(25), netCoder-5-6(26), netCoder-6-4(27), netCoder-7-2(28), netCoder-8(29), netCoder-8-8(30), netCoder-9-6(31), eVRC(32), eVRC-TFO(33), qCELP-8(34), qCELP-8-TFO(35), qCELP-13(36), qCELP-13-TFO(37), noCoder(40), modemAnswer(41), modemCall(42), g711Alaw-5-5(45), g711Mulaw-5-5(46), g726-32-5-5(47), aMR-4-75(50), aMR-5-15(51), aMR-5-9(52), aMR-6-7(53), aMR-7-4(54), aMR-7-95(55), aMR-10-2(56), aMR-12-2(57), iLBC-15(63), iLBC-13(64), bV-16(65), acAMRWB-6-6(66), acAMRWB-8-85(67), acAMRWB-12-65(68), acAMRWB-14-25(69), acAMRWB-15-85(70), acAMRWB-18-25(71), acAMRWB-19-85(72), acAMRWB-23-05(73), acAMRWB-23-85(74), acG722-48K(75), acG722-56K(76), acG722-64K(77), acDPNSSCoder(78)}read-onlydeprecated
eCE
OBJECT-TYPE
Enable/Disable Echo Canceler
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.3INTEGER {disable(0), enable(1)}read-onlydeprecated
sCE
OBJECT-TYPE
Enable/Disable Silence Compresion mechanism
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.4INTEGER {disable(0), enable(1)}read-onlydeprecated
pFE
OBJECT-TYPE
Post Filter Enable of the voice coder
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.5INTEGER {disable(0), enable(1)}read-onlydeprecated
hPFE
OBJECT-TYPE
High Pass Filter Enabled of the voice coder
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.6INTEGER {disable(0), enable(1)}read-onlydeprecated
testMode
OBJECT-TYPE
Testing mode to be applied. Valid Range:CoderLoopback will perform an encoder-decoder loopback inside the DSP device, PCMLoopback will loopback the incoming PCM to the outgoing PCM, ToneInjection will generate a1000 Hz tone to outgoing PCM and NoLoopback will set the channel to work in a normal mode. Refer to TTestCode enumeration (default =3= NoLoopBack).
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.7INTEGER {coderLoopback(0), pCMLoopback(1), toneInjection(2), noLoopback(3)}read-onlydeprecated
voiceVolume
OBJECT-TYPE
Voice Volume sets the voice decoder’s output gain Range: 0-63 corresponding to -31 dB to +31 dB in 1 dB steps
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.8INTEGER (0..63)read-onlydeprecated
inputGain
OBJECT-TYPE
PCM input gain sets the gain at the encoder’s input.
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.9INTEGER (0..63)read-onlydeprecated
m
OBJECT-TYPE
This Packet Multiply Factor is the Number of 20 msec payloads (30 msec for G.723) to be used for generating one RTP packet. Range: 1 - Until max Tx/Rx buffer size is reached
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.10INTEGER (1..12)read-onlydeprecated
rTPRedundancyDepth
OBJECT-TYPE
RTP Redundancy Depth. Number of repetitions to be applied to each RTP payload when transmitting to network. apply redundancy sequence per RFC2198. Valid range: Disable redundancy packets generation = 0. Enable generation of RFC2198 redundancy packets = 1.
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.11INTEGER {disable(0), enable(1)}read-onlydeprecated
eCLength
OBJECT-TYPE
Length of echo canceler tail to be used according to TECLength enumeration. Note that EC length has different length limitations for different boards.
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.12INTEGER {eCLength10MSec(0), eCLength15Msec(1), eCLength20Msec(2), eCLength25Msec(3), eCLength30Msec(4), eCLength35Msec(5), eCLength40Msec(6), eCLength45Msec(7), eCLength50Msec(8), eCLength55Msec(9), eCLength60Msec(10)}read-onlydeprecated
eCHybridLoss
OBJECT-TYPE
Echo Cancler Hybrid Loss. sets the worst case ratio between the signal level transmitted to the hybrid and the echo level returning from the hybrid. User should set this value according to the worst hybrid in the system in terms of echo return loss according to enum TECHybridLoss enumeration
1.3.6.1.4.1.5003.9.10.1.3.2.1.1.13INTEGER {loss6DB(0), loss9DB(1), loss0DB(2), loss3DB(3)}read-onlydeprecated
faxModemSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.3
faxModemSettingsTable
OBJECT-TYPE
Data in faxModem Settings Table uniquely identify fax and modem parameters channel.
1.3.6.1.4.1.5003.9.10.1.3.3.1not-accessibleobsolete
faxModemSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.3.1.1not-accessibleobsolete
fAXTransportType
OBJECT-TYPE
FAX Transport Type.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.1INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
acCallerIDType
OBJECT-TYPE
CallerID Type.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.2INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
v21ModemTransportType
OBJECT-TYPE
V21 Modem Transpor tType.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.3INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
v22ModemTransportType
OBJECT-TYPE
V22 Modem Transpor tType.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.4INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
v23ModemTransportType
OBJECT-TYPE
V23 Modem Transpor tType.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.5INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
v32ModemTransportType
OBJECT-TYPE
V32 Modem Transpor tType.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.6INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
v34ModemTransportType
OBJECT-TYPE
V34 Modem Transpor tType.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.7INTEGER {transparent(0), relay(1), bypass(2)}read-onlyobsolete
faxRelayMaxRate
OBJECT-TYPE
Fax Relay Max Rate Limits the maximum rate at which fax messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.8INTEGER {ac2400(0), ac4800(1), ac7200(2), ac9600(3), ac12000(4), ac14400(5)}read-onlyobsolete
modemRelayMaxRate
OBJECT-TYPE
Modem Relay Max Rate Limits the maximum rate at which modem relay messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.9INTEGER {ac2400(0), ac4800(1), ac7200(2), ac9600(3), ac12000(4), ac14400(5)}read-onlyobsolete
faxRelayECMEnable
OBJECT-TYPE
Fax Relay ECM Enable Enable using ECM mode during Fax Relay.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.10INTEGER {disable(0), enable(1)}read-onlyobsolete
t38FaxRelayProtectionMode
OBJECT-TYPE
T38 Fax Relay Protection Mode Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.11INTEGER {redundancyPackets(0), fEC(1)}read-onlyobsolete
faxRelayRedundancyDepth
OBJECT-TYPE
Fax Relay Redundancy Depth Number of repetitions to be applied to each fax relay payload when transmitting to network (applicable only when acTFaxModemCmdacTFaxModemSettings.T38FaxRelayProtectionMode=0).
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.12INTEGER (0..4)read-onlyobsolete
enhancedFaxRelayRedundancyDepth
OBJECT-TYPE
Enhanced Fax Relay Redundancy Depth Number of repetitions to be applied to control packets when using T.38 standard.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.13INTEGER (0..4)read-onlyobsolete
modemRelayRedundancyDepth
OBJECT-TYPE
Modem Relay Redundancy Depth Number of repetitions to be applied to each modem relay payload when transmitting to network.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.14INTEGER {disable(0), enable(1)}read-onlyobsolete
faxModemRelayVolume
OBJECT-TYPE
Fax Modem Relay Volume Fax gain control. Range: -18 - 15 corresponding to -18.5 dBm to -3.5 dBm in 1 dB steps. The reason the range extends to 15 is for backward compatibility. (Default =6).
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.15INTEGER (-18..15)read-onlyobsolete
faxModemBypassCoderType
OBJECT-TYPE
Fax Modem Bypass Coder Type Coder to be used while performing fax/modem bypass. Usually, high bit rate coders such as G.711 and G.726/G.727 should be used. (Default = G.711 A-law).
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.16INTEGER {g711Alaw(0), g711Mulaw(1), g726-16(2), g726-24(3), g726-32(4), g726-40(5), g727-16(6), g727-24-16(7), g727-24(8), g727-32-16(9), g727-32-24(10), g727-32(11), g727-40-16(12), g727-40-24(13), g727-40-32(14), g723Low(15), g723High(16), g729(17), gSM(19), gSM610MS(20), transparent(22), g728(23), hDLCCoder(24), netCoder-4-8(25), netCoder-5-6(26), netCoder-6-4(27), netCoder-7-2(28), netCoder-8(29), netCoder-8-8(30), netCoder-9-6(31)}read-onlyobsolete
faxModemBypassM
OBJECT-TYPE
Fax Modem Bypass M Number of 20 msec payloads to be used for generating one RTP fax/modem bypass packet. Range: 1 - Until max Tx/Rx buffer size is reached
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.17INTEGER (0..2147483647)read-onlyobsolete
useT38orFRF11
OBJECT-TYPE
Use T38 or FRF11 Use T.38 protocol or proprietary FRF.11 syntax, to send/receive fax relay.
1.3.6.1.4.1.5003.9.10.1.3.3.1.1.18INTEGER {fRF11(0), t38(1)}read-onlyobsolete
dJBSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.4
dJBSettingsTable
OBJECT-TYPE
Data in dJB Settings Table uniquely identify jitter buffer parameters of channel.
1.3.6.1.4.1.5003.9.10.1.3.4.1not-accessibleobsolete
dJBSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.4.1.1not-accessibleobsolete
dJBufMinDelay
OBJECT-TYPE
[Millisec] Dynamic Jitter Buffer Minimum Delay. 0 - 150 (default =150)
1.3.6.1.4.1.5003.9.10.1.3.4.1.1.1INTEGER (0..150)read-onlyobsolete
dJBufOptFactor
OBJECT-TYPE
Dynamic Jitter Buffer Optimization Factor. Dynamic jitter buffer frame error/delay optimization. 0 - 12 (default =7)
1.3.6.1.4.1.5003.9.10.1.3.4.1.1.2INTEGER (0..12)read-onlyobsolete
channelTDMBusSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.5
channelTDMBusSettingsTable
OBJECT-TYPE
Data in channel TDM Bus Settings Table, uniquely identify TDM Bus sparameters of channel
1.3.6.1.4.1.5003.9.10.1.3.5.1not-accessibleobsolete
channelTDMBusSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.5.1.1not-accessibleobsolete
tDMBusInputPort
OBJECT-TYPE
TDM Bus Input Port. Together with TDMBusInputChannel, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When using TDMBusType=acFramers this parameter selects the trunkID, in which the incoming B-channel resides. 0-127.
1.3.6.1.4.1.5003.9.10.1.3.5.1.1.1INTEGER (0..127)read-onlyobsolete
tDMBusInputChannel
OBJECT-TYPE
TDM Bus Input Channel. Together with TDMBusInputPort, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter selects the incoming B-channel (in this case the valid region is 0-31).
1.3.6.1.4.1.5003.9.10.1.3.5.1.1.2INTEGER (0..31)read-onlyobsolete
tDMBusOutputDisable
OBJECT-TYPE
TDM Bus Output Disable. 0: Places TDM bus output timeslot in tri-state mode. Ignored in case of PSTN interface. 1: Enables TDM bus output timeslot. Ignored in case of PSTN interface.
1.3.6.1.4.1.5003.9.10.1.3.5.1.1.3INTEGER {disable(0), enable(1)}read-onlyobsolete
tDMBusOutputPort
OBJECT-TYPE
TDM Bus Output Port. Together with TDMBusOutputChannel, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When this parameter is set to 0xff=255 the boardwise setting (set in acOpenBoard()) will be used. When using TDMBusType=acFramers, this parameter is ignored. 0-31 or 255.
1.3.6.1.4.1.5003.9.10.1.3.5.1.1.4INTEGER (0..255)read-onlyobsolete
tDMBusOutputChannel
OBJECT-TYPE
TDM Bus Output Channel. Together with TDMBusOutputPort, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter is ignored.
1.3.6.1.4.1.5003.9.10.1.3.5.1.1.5INTEGER (0..2147483647)read-onlyobsolete
transportSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.6
transportSettingsTable
OBJECT-TYPE
Data in Transport Table, uniquely identify Transport sparameters of channel.
1.3.6.1.4.1.5003.9.10.1.3.6.1not-accessibleobsolete
transportSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.6.1.1not-accessibleobsolete
useNIorPCI
OBJECT-TYPE
Description: Use NI or PCI interface. =1 if channel will use NI interface, =0 if PCI interface. 0- PCI interface: Compressed traffic will be sent/received through the PCI interface. 1- NI interface: RTP-RTCP packets sent/received to/from on board Ethernet interface. (default=1).
1.3.6.1.4.1.5003.9.10.1.3.6.1.1.1INTEGER (0..1)read-onlyobsolete
disableSoftIPLoopback
OBJECT-TYPE
Disable Soft IP Loopback =1 in order to diable soft IP loopback. 0- Enables the hair pin connection made in case two channels on the same board are connected together. 1- Disables the hair pin connection made in case two channels on the same board are connected together.
1.3.6.1.4.1.5003.9.10.1.3.6.1.1.2INTEGER (0..1)read-onlyobsolete
uniDirectionalRTP
OBJECT-TYPE
uni Directional RTP. enables one sided RTP stream - according to niDirectionalRTPMode. enables the User to set the channel to work with unidirectional RTP streams. When UniDirectionalRTP is set to acRTPTxOnly, the receiver part of the channel will be disabled, and only the transmitter (encoder) will work. When UniDirectionalRTP is set to acRTPRxOnly, the transmitter part of the channel will be disabled, and only the receiver (decoder) will work. When UniDirectionalRTP is set to acRTPTxRx, both sides will be enabled. Users should note that when configuring a session between two endpoints, some of the channel configuration parameters must be identical on both sides. Such parameters are the voice coder type, the Fax/Modem transport type and bypass coders. All other configuration parameters are independent.
1.3.6.1.4.1.5003.9.10.1.3.6.1.1.3INTEGER (0..2147483647)read-onlyobsolete
rTPRTCPSettings
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.3.7
rTPRTCPSettingsTable
OBJECT-TYPE
Data in RTP-RTCP Table, uniquely identify RTP-RTCP sparameters of channel.
1.3.6.1.4.1.5003.9.10.1.3.7.1not-accessibleobsolete
rTPRTCPSettingsEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.3.7.1.1not-accessibleobsolete
cNAME
OBJECT-TYPE
RTP Canonical Name. Should be unique among all participants within one RTP session. Refer to RFC1890 for more information. Up to 255 characters string. (default ='ChX', X=CID).
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.1OCTET STRING (SIZE(0..255))read-onlyobsolete
iPPrecedence
OBJECT-TYPE
IP Precedence. Sets the value of the IP precedence field in the IP header for all the packets to be generated from this channel. Follow the acTIPPrecedence enumeration. Valid Range: 0-7 (default =0)
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.2INTEGER (0..7)read-onlyobsolete
iPTOS
OBJECT-TYPE
iP Type Of Service. sets the value of the IP Type Of Service field in the IP header for all the packets to be generated from this channel. acNormalServiceTOS=0, acMinimizeMonetaryCostTOS=1, acMaximizeReliabilityTOS=2, acMaximizeThroughputTOS=4, acMinimizeDelayTOS=8 (Follow the acTIPTOS enumeration).
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.3INTEGER (0..15)read-onlyobsolete
localRTPPort
OBJECT-TYPE
Local RTP Port. Local UDP Port to be used for incoming RTP stream to this channel. This parameter also sets the local RTCP and local T.38 ports in offset of 1,2 from LocalRTPPort respectively. The local RTP port must be a number dividable by 10 and must reside within the following range BoardParams.BaseUDPPort-> BoardParams.BaseUDPPort +10*MAX_CID_NUM.
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.4INTEGER (0..2147483647)read-onlyobsolete
remoteRTPAddr
OBJECT-TYPE
Remote RTP Address
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.5IpAddressread-onlyobsolete
remoteRTPPort
OBJECT-TYPE
IP/UDP Address of the remote endpoint RTP port
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.6INTEGER (0..2147483647)read-onlyobsolete
remoteT38Addr
OBJECT-TYPE
remote T38 Address
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.7IpAddressread-onlyobsolete
remoteT38Port
OBJECT-TYPE
IP/UDP Address of the remote endpoint T.38 port
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.8INTEGER (0..2147483647)read-onlyobsolete
rTCPMeanTxInterval
OBJECT-TYPE
RTCP Mean Tx Interval. Mean interval [msec] between channel's RTCP reports.
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.9INTEGER (100..2147483647)read-onlyobsolete
rxRTPPayloadType
OBJECT-TYPE
Rx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127 . (default =-1).
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.10INTEGER (-2..127)read-onlyobsolete
txRTPPayloadType
OBJECT-TYPE
Tx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127. (default =-1).
1.3.6.1.4.1.5003.9.10.1.3.7.1.1.11INTEGER (-2..127)read-onlyobsolete
channelStatus
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.4
channelStatusTable
OBJECT-TYPE
Data in voice SettingsTable uniquely identify a voice parameters of channel.
1.3.6.1.4.1.5003.9.10.1.4.1not-accessibleobsolete
channelStatusEntry
OBJECT-TYPE
1.3.6.1.4.1.5003.9.10.1.4.1.1not-accessibleobsolete
rTPActive
OBJECT-TYPE
RTP Active
1.3.6.1.4.1.5003.9.10.1.4.1.1.1INTEGER {notActive(0), active(1)}read-onlydeprecated
bypassNIC
OBJECT-TYPE
Bypass NIC
1.3.6.1.4.1.5003.9.10.1.4.1.1.2INTEGER (0..1)read-onlydeprecated
pendingIdle
OBJECT-TYPE
Pending Idle
1.3.6.1.4.1.5003.9.10.1.4.1.1.3INTEGER (0..1)read-onlyobsolete
txSilencePeriod
OBJECT-TYPE
Tx Silence Period
1.3.6.1.4.1.5003.9.10.1.4.1.1.4INTEGER (0..1)read-onlydeprecated
rxSilencePeriod
OBJECT-TYPE
Rx Silence Period
1.3.6.1.4.1.5003.9.10.1.4.1.1.5INTEGER (0..1)read-onlydeprecated
txFaxMode
OBJECT-TYPE
Tx Fax Mode
1.3.6.1.4.1.5003.9.10.1.4.1.1.6INTEGER (0..1)read-onlydeprecated
rxFaxMode
OBJECT-TYPE
Rx Fax Mode
1.3.6.1.4.1.5003.9.10.1.4.1.1.7INTEGER (0..1)read-onlydeprecated
txDTMFPeriod
OBJECT-TYPE
Tx DTMF Period
1.3.6.1.4.1.5003.9.10.1.4.1.1.8INTEGER (0..1)read-onlydeprecated
rxDTMFPeriod
OBJECT-TYPE
Rx DTMF Period
1.3.6.1.4.1.5003.9.10.1.4.1.1.9INTEGER (0..1)read-onlydeprecated
packetsToDSPCnt
OBJECT-TYPE
Jitter Buffer Error Counter
1.3.6.1.4.1.5003.9.10.1.4.1.1.10INTEGER (0..2147483647)read-onlydeprecated
jitterBufErrorCnt
OBJECT-TYPE
Jitter Buffer Forced Packet count
1.3.6.1.4.1.5003.9.10.1.4.1.1.11INTEGER (0..2147483647)read-onlyobsolete
jitterBufForcedPacketLost
OBJECT-TYPE
Jitter Buffer Forced Packet Lost
1.3.6.1.4.1.5003.9.10.1.4.1.1.12INTEGER (0..2147483647)read-onlyobsolete
jitterBufForcedPacketAddition
OBJECT-TYPE
Jitter Buffer Forced Packet Addition
1.3.6.1.4.1.5003.9.10.1.4.1.1.13INTEGER (0..2147483647)read-onlyobsolete
jitterBufUnderRunCnt
OBJECT-TYPE
Jitter Buffer Under-Run Counter
1.3.6.1.4.1.5003.9.10.1.4.1.1.14INTEGER (0..2147483647)read-onlydeprecated
jitterBufOverRunCnt
OBJECT-TYPE
Jitter Buffer Over-Run Counter
1.3.6.1.4.1.5003.9.10.1.4.1.1.15INTEGER (0..2147483647)read-onlydeprecated
jitterBufAccumDelay
OBJECT-TYPE
Jitter Buffer accumulation Delay. In packets.
1.3.6.1.4.1.5003.9.10.1.4.1.1.16INTEGER (0..2147483647)read-onlyobsolete
fXSorFXO
OBJECT-TYPE
returns the type phisical type of endpoint
1.3.6.1.4.1.5003.9.10.1.4.1.1.17INTEGER {nonAnalogDevice(-1), fXO(0), fXS(1)}read-onlydeprecated
channelHookState
OBJECT-TYPE
Channel Hook State
1.3.6.1.4.1.5003.9.10.1.4.1.1.18INTEGER {nonAnalogDevice(-1), offHook(0), onHook(1)}read-onlydeprecated
notifications
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.5
reset
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.6
remoteReset
OBJECT-TYPE
remote Reset. To remote reset the board, set an integer value to this parameter. Note: Before Reset, The current boardConfiguration parameters will be burned to the board.
1.3.6.1.4.1.5003.9.10.1.6.1INTEGER (0..2147483647)read-writeobsolete
acSetDefaults
OBJECT-TYPE
To set the default values, set an integer value to this parameter
1.3.6.1.4.1.5003.9.10.1.6.2INTEGER (1..2147483647)read-writeobsolete
acgwAdminState
OBJECT-TYPE
Determines the gateway's operational state. 0 - locked: Shutdown the GW In the time frame set by acgwAdminStateLockControl 1 - shuttingDown: (read only) Graceful Shutdown is being carried out 2 - unlocked: GW is in service.
1.3.6.1.4.1.5003.9.10.1.6.3INTEGER {locked(0), shuttingDown(1), unlocked(2)}read-writeobsolete
acgwAdminStateLockControl
OBJECT-TYPE
(in sec) time left for the graceful shutdown to complete. -1 indicates unlimited time frame. 0 indicates immediate (forced) lock. Implementing the control requires setting acgwAdminState to locked.
1.3.6.1.4.1.5003.9.10.1.6.4INTEGER (-1..65535)read-writeobsolete
acSaveConfigToSystem
OBJECT-TYPE
This will save all current configuration in the board onto the flash. Any digit will call on the function. NOTE: Do NOT save the configuration while voice is running - this will cause a delay.
1.3.6.1.4.1.5003.9.10.1.6.5INTEGER (0..2147483647)read-writeobsolete
acOperationalState
OBJECT-TYPE
The operational state of the gateway.
1.3.6.1.4.1.5003.9.10.1.6.6INTEGER {disabled(1), enabled(2)}read-onlyobsolete
remoteResetControl
OBJECT-TYPE
Determine the remote reset action 1 - burn staged load image, if any, and config to flash, perform a reset, and load from flash 2 - perform a reset, and load from flash (staged load image, if any, and config is not burned to flash) 3 - perform a reset, and load from bootp/tftp (staged load image, if any, and config burn is not needed) * - an error is returned for any other value Note: The staged load image is an image of a cmp file that was previously loaded to a area in RAM via an HTTP upload
1.3.6.1.4.1.5003.9.10.1.6.7INTEGER {resetFromFlashAfterBurn(1), resetFromFlashNoBurn(2), resetFromBootP(3)}read-writeobsolete
acTrap
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.21
acBoardTrapGlobals
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.21.1
acBoardTrapGlobalsName
OBJECT-TYPE
trap name
1.3.6.1.4.1.5003.9.10.1.21.1.1INTEGER (0..1000)read-onlydeprecated
acBoardTrapGlobalsTextualDescription
OBJECT-TYPE
title of trap
1.3.6.1.4.1.5003.9.10.1.21.1.2OCTET STRING (SIZE(0..200))read-onlydeprecated
acBoardTrapGlobalsSource
OBJECT-TYPE
Trap Source - MG1/Shelf1/Board2/Trunk3
1.3.6.1.4.1.5003.9.10.1.21.1.3OCTET STRING (SIZE(0..100))read-onlydeprecated
acBoardTrapGlobalsSeverity
OBJECT-TYPE
Trap Severity
1.3.6.1.4.1.5003.9.10.1.21.1.4INTEGER {cleared(0), indeterminate(1), warning(2), minor(3), major(4), critical(5)}read-onlydeprecated
acBoardTrapGlobalsUniqID
OBJECT-TYPE
Trap Uniq Id - generated by AcBoard and should be uniq for the entire EMS
1.3.6.1.4.1.5003.9.10.1.21.1.5INTEGER (0..32000)read-onlydeprecated
acBoardTrapGlobalsType
OBJECT-TYPE
Trap type - ItuAlarmType
1.3.6.1.4.1.5003.9.10.1.21.1.6INTEGER {other(0), communicationsAlarm(1), qualityOfServiceAlarm(2), processingErrorAlarm(3), equipmentAlarm(4), environmentalAlarm(5)}read-onlydeprecated
acBoardTrapGlobalsProbableCause
OBJECT-TYPE
Trap probable cause - SnmpAlarmProbableCause
1.3.6.1.4.1.5003.9.10.1.21.1.7INTEGER {other(0), adapterError(1), applicationSubsystemFailure(2), bandwidthReduced(3), callEstablishmentError(4), communicationsProtocolError(5), communicationsSubsystemFailure(6), configurationOrCustomizationError(7), congestion(8), corruptData(9), cpuCyclesLimitExceeded(10), dataSetOrModemError(11), degradedSignal(12), dteDceInterfaceError(13), enclosureDoorOpen(14), equipmentMalfunction(15), excessiveVibration(16), fileError(17), fireDetected(18), floodDetected(19), framingError(20), heatingVentCoolingSystemProblem(21), humidityUnacceptable(22), inputOutputDeviceError(23), inputDeviceError(24), lanError(25), leakDetected(26), localNodeTransmissionError(27), lossOfFrame(28), lossOfSignal(29), materialSupplyExhausted(30), multiplexerProblem(31), outOfMemory(32), ouputDeviceError(33), performanceDegraded(34), powerProblem(35), pressureUnacceptable(36), processorProblem(37), pumpFailure(38), queueSizeExceeded(39), receiveFailure(40), receiverFailure(41), remoteNodeTransmissionError(42), resourceAtOrNearingCapacity(43), responseTimeExecessive(44), retransmissionRateExcessive(45), softwareError(46), softwareProgramAbnormallyTerminated(47), softwareProgramError(48), storageCapacityProblem(49), temperatureUnacceptable(50), thresholdCrossed(51), timingProblem(52), toxicLeakDetected(53), transmitFailure(54), transmitterFailure(55), underlyingResourceUnavailable(56), versionMismatch(57), authenticationFailure(58), breachOfConfidentiality(59), cableTamper(60), delayedInformation(61), denialOfService(62), duplicateInformation(63), informationMissing(64), informationModificationDetected(65), informationOutOfSequence(66), intrusionDetection(67), keyExpired(68), nonRepudiationFailure(69), outOfHoursActivity(70), outOfService(71), proceduralError(72), unauthorizedAccessAttempt(73), unexpectedInformation(74)}read-onlydeprecated
acBoardTrapGlobalsAdditionalInfo1
OBJECT-TYPE
Trap additional info global field
1.3.6.1.4.1.5003.9.10.1.21.1.8OCTET STRING (SIZE(0..100))read-onlydeprecated
acBoardTrapGlobalsAdditionalInfo2
OBJECT-TYPE
Trap additional info global field
1.3.6.1.4.1.5003.9.10.1.21.1.9OCTET STRING (SIZE(0..100))read-onlydeprecated
acBoardTrapGlobalsAdditionalInfo3
OBJECT-TYPE
Trap additional info global field
1.3.6.1.4.1.5003.9.10.1.21.1.10OCTET STRING (SIZE(0..100))read-onlydeprecated
acBoardTrapGlobalsDateAndTime
OBJECT-TYPE
Date and time that the trap was sent.
1.3.6.1.4.1.5003.9.10.1.21.1.11DateAndTimeread-onlydeprecated
acBoardTrapDefinitions
OBJECT-IDENTITY
1.3.6.1.4.1.5003.9.10.1.21.2

Notifications

NameOIDStatus
acBoardFatalError
NOTIFICATION-TYPE
Board fatal error
1.3.6.1.4.1.5003.9.10.1.21.2.0.1current
acBoardConfigurationError
NOTIFICATION-TYPE
Configuration Error
1.3.6.1.4.1.5003.9.10.1.21.2.0.2current
acBoardTemperatureAlarm
NOTIFICATION-TYPE
Temperature Alarm. Turned on when temperature exceeds 60 degrees Celsius, and relaxes when temperature goes under 55 again.
1.3.6.1.4.1.5003.9.10.1.21.2.0.3current
acBoardEvBoardStarted
NOTIFICATION-TYPE
Initialization Ended
1.3.6.1.4.1.5003.9.10.1.21.2.0.4current
acBoardEvResettingBoard
NOTIFICATION-TYPE
The board start Reset process - following software reset
1.3.6.1.4.1.5003.9.10.1.21.2.0.5current
acFeatureKeyError
NOTIFICATION-TYPE
Feature key related Error
1.3.6.1.4.1.5003.9.10.1.21.2.0.6current
acgwAdminStateChange
NOTIFICATION-TYPE
The administrative state of the gate way has been changed to a new state.
1.3.6.1.4.1.5003.9.10.1.21.2.0.7current
acBoardCallResourcesAlarm
NOTIFICATION-TYPE
No free channels available
1.3.6.1.4.1.5003.9.10.1.21.2.0.8current
acBoardControllerFailureAlarm
NOTIFICATION-TYPE
The GK/Proxy not found or registration failed. internal routing table may be used for routing
1.3.6.1.4.1.5003.9.10.1.21.2.0.9current
acBoardEthernetLinkAlarm
NOTIFICATION-TYPE
Ethernet Link is down or remote Ethernet link is down and board has no communication to any other host
1.3.6.1.4.1.5003.9.10.1.21.2.0.10current
acBoardOverloadAlarm
NOTIFICATION-TYPE
Overload in one or some of the system's components
1.3.6.1.4.1.5003.9.10.1.21.2.0.11current
acActiveAlarmTableOverflow
NOTIFICATION-TYPE
An active alarm could not be placed in the active alarm table because the table is full. This alarm will not clear. Reboot is the only way to completely clear the Active Alarm table overflow problem. Any alarm raised at this state will not be Carrier Grade compatible. Therefore, Updates will not clear the alarm before changing the bindings and re-raising alarms. The History tables remain unaffected. All Alarms raised prior to overflow will remain Carrier Grade compatible. Other alarms, raised after this alarm was raised, that are placed in the Active Alarm table will be Carrier Grade compatible. (This is for when after the alarm was raised there were some clears, clearing alarms off the Active Alarm table).
1.3.6.1.4.1.5003.9.10.1.21.2.0.12current
acAtmPortAlarm
NOTIFICATION-TYPE
ATM Port Alarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.13current
acAudioProvisioningAlarm
NOTIFICATION-TYPE
This alarm is raised if the Media Server is unable to provision its audio. This could be because the Audio Provisioning System (APS) is down or there is a network problem.
1.3.6.1.4.1.5003.9.10.1.21.2.0.14current
acOperationalStateChange
NOTIFICATION-TYPE
This alarm is raised if the operational state of the node goes to disabled. The alarm is cleared when the operational state of the node goes to enabled.
1.3.6.1.4.1.5003.9.10.1.21.2.0.15current
acKeepAlive
NOTIFICATION-TYPE
This trap is the NAT Traversal keep alive trap. If the STUN application in the device detects a NAT then this trap will be sent out on a regular time laps - 9/10 of the acSysSTUNBindingLifeTime object. The AdditionalInfo1 varbind has the MAC address of the device. Note that all traps are sent out from the SNMP Port (usually 161).
1.3.6.1.4.1.5003.9.10.1.21.2.0.16current
acNATTraversalAlarm
NOTIFICATION-TYPE
When the NAT placed in front a device is identified as a symmetric NAT - this alarm is raised. It is cleared when a non-symmetric NAT or no NAT replace the symmetric one.
1.3.6.1.4.1.5003.9.10.1.21.2.0.17current
acEnhancedBITStatus
NOTIFICATION-TYPE
This trap is used to for the status of the BIT (Built In Test). The information in the trap contains board HW elements being tested and their status. The information is presented in the additional info fields.
1.3.6.1.4.1.5003.9.10.1.21.2.0.18current
acSS7LinkStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the operational state of the SS7 link becomes XXXX. The alarm is cleared when the operational state of the link becomes XXXX.
1.3.6.1.4.1.5003.9.10.1.21.2.0.19current
acSS7LinkInhibitStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the SS7 link becomes inhibited (local or remote). The alarm is cleared when the link becomes uninhibited - local AND remote. Note that this alarm will be raised for any change in the remote or local inhibition status.
1.3.6.1.4.1.5003.9.10.1.21.2.0.20current
acSS7LinkBlockStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the SS7 link becomes blocked (local or remote). The alarm is cleared when the link becomes unblocked - local AND remote. Note that this alarm will be raised for any change in the remote or local blocking status.
1.3.6.1.4.1.5003.9.10.1.21.2.0.21current
acSS7LinkCongestionStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the SS7 link becomes congested (local or remote). The alarm is cleared when the link becomes uncongested - local AND remote. Note that this alarm will be raised for any change in the remote or local congestion status.
1.3.6.1.4.1.5003.9.10.1.21.2.0.22current
acSS7LinkSetStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the operational state of the SS7 linkset becomes BUSY. The alarm is cleared when the operational state of the linkset becomes IN-SERVICE or OFFLINE.
1.3.6.1.4.1.5003.9.10.1.21.2.0.23current
acSS7RouteSetStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the operational state of the SS7 routeset becomes BUSY. The alarm is cleared when the operational state of the routeset becomes IN-SERVICE or OFFLINE.
1.3.6.1.4.1.5003.9.10.1.21.2.0.24current
acSS7SNSetStateChangeAlarm
NOTIFICATION-TYPE
This alarm is raised if the operational state of the SS7 node becomes BUSY. The alarm is cleared when the operational state of the node becomes IN-SERVICE or OFFLINE.
1.3.6.1.4.1.5003.9.10.1.21.2.0.25current
acSS7RedundancyAlarm
NOTIFICATION-TYPE
Raised when the SS7 redundancy degregated. Cleared when all entities of redundancy are fully functional and in serveice.
1.3.6.1.4.1.5003.9.10.1.21.2.0.26current
acPerformanceMonitoringThresholdCrossing
NOTIFICATION-TYPE
This log trap is sent out for every time the threshold of a Performance Monitored object is crossed. The severity field is 'indeterminate' when the crossing is above the threshold and 'cleared' when it goes back under the threshold. The 'source' varbind in the trap indicates the object for which the threshold is being crossed.
1.3.6.1.4.1.5003.9.10.1.21.2.0.27current
acHTTPDownloadResult
NOTIFICATION-TYPE
This trap indicates the result of a recent file download (includes HTTP error code, if available).
1.3.6.1.4.1.5003.9.10.1.21.2.0.28current
acFanTrayAlarm
NOTIFICATION-TYPE
This alarm is raised when the fan tray is missing or some of the fans are faulty. If the fan tray is missing or more then X fans are faulty the severity will be Critical. If more then one and less the X fans are faulty the severity will be Major.
1.3.6.1.4.1.5003.9.10.1.21.2.0.29current
acPowerSupplyAlarm
NOTIFICATION-TYPE
This alarm is raised when the HA (High Availability) feature is active and one of the power supply units is faulty.
1.3.6.1.4.1.5003.9.10.1.21.2.0.30current
acPEMAlarm
NOTIFICATION-TYPE
This alarm is raised when the HA (High Availability) feature is active. The severity is critical if one of the PEM units is missing and major if the electric wire to one of the units is disconnected.
1.3.6.1.4.1.5003.9.10.1.21.2.0.31current
acSAMissingAlarm
NOTIFICATION-TYPE
This alarm is raised when the SA module in the M3K MG is missing. Whenthere is no SAT there are no other chassis HW related alarms. Note - relevant only for M3K.
1.3.6.1.4.1.5003.9.10.1.21.2.0.32current
acHASystemFaultAlarm
NOTIFICATION-TYPE
This alarm is raised when the HA (High Availability) feature is active and the system is NOT HA. Critical severity - 1.Wrong HW Configuration. 2. Redundant module is missing (not in slot). 3. The redundant module is non operable. Minor severity - waiting for redunadant to connect (after reset!).
1.3.6.1.4.1.5003.9.10.1.21.2.0.33current
acHASystemConfigMismatchAlarm
NOTIFICATION-TYPE
This alarm is raised when the HA (High Availability) feature is active and there has been a configuration change due to which the HA system may or may not be usable.
1.3.6.1.4.1.5003.9.10.1.21.2.0.34current
acHASystemSwitchOverAlarm
NOTIFICATION-TYPE
This alarm is raised when the HA (High Availability) feature is active and there has been a switchover due to failure or reset in the active module.
1.3.6.1.4.1.5003.9.10.1.21.2.0.35current
acUserInputAlarm
NOTIFICATION-TYPE
This Alarm is raised when the input dry contact is short circuited. Cleared when the circuit is reopened.
1.3.6.1.4.1.5003.9.10.1.21.2.0.36current
acDChannelStatus
NOTIFICATION-TYPE
This non alarm trap is sent when establishment, re-establishment or release of LAPD link with its peer connection occurs. The trap will be sent out with one of the following in the textual description: D-channel synchronized D-channel not-synchronized
1.3.6.1.4.1.5003.9.10.1.21.2.0.37current
acSonetSectionLOFAlarm
NOTIFICATION-TYPE
SONET section Loss of Frame alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.38current
acSonetSectionLOSAlarm
NOTIFICATION-TYPE
SONET section Loss of Signal alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.39current
acSonetLineAISAlarm
NOTIFICATION-TYPE
SONET Line AIS alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.40current
acSonetLineRDIAlarm
NOTIFICATION-TYPE
SONET Line RDI alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.41current
acSonetIfHwFailureAlarm
NOTIFICATION-TYPE
SONET or SDH medium Interface has failed.
1.3.6.1.4.1.5003.9.10.1.21.2.0.42current
acHwFailureAlarm
NOTIFICATION-TYPE
HW failure alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.43current
acH248LostConnectionWithCA
NOTIFICATION-TYPE
H248 lost connection with call agent
1.3.6.1.4.1.5003.9.10.1.21.2.0.44current
acDialPlanFileReplaced
NOTIFICATION-TYPE
dial plan file replaced notification
1.3.6.1.4.1.5003.9.10.1.21.2.0.45current
acAnalogPortSPIOutOfService
NOTIFICATION-TYPE
Analog port out of service
1.3.6.1.4.1.5003.9.10.1.21.2.0.46current
acAnalogPortHighTemperature
NOTIFICATION-TYPE
Analog Port High Temperature
1.3.6.1.4.1.5003.9.10.1.21.2.0.47current
acHitlessUpdateStatus
NOTIFICATION-TYPE
Notification trap that is sent out at the beginning and the end of a Hitless SW update. Failure during the process will also instigate the trap. Relevant to HA systems only.
1.3.6.1.4.1.5003.9.10.1.21.2.0.48current
acTrunksAlarmNearEndLOS
NOTIFICATION-TYPE
Loss of signal at trunk's near end.
1.3.6.1.4.1.5003.9.10.1.21.2.0.49current
acTrunksAlarmNearEndLOF
NOTIFICATION-TYPE
Loss of frame at trunk's near end.
1.3.6.1.4.1.5003.9.10.1.21.2.0.50current
acTrunksAlarmRcvAIS
NOTIFICATION-TYPE
Received AIS from trunk's far end.
1.3.6.1.4.1.5003.9.10.1.21.2.0.51current
acTrunksAlarmFarEndLOF
NOTIFICATION-TYPE
Loss of frame at trunk's far end.
1.3.6.1.4.1.5003.9.10.1.21.2.0.52current
acIPv6ErrorAlarm
NOTIFICATION-TYPE
Alarm trap that is sent out for IPv6 related errors.
1.3.6.1.4.1.5003.9.10.1.21.2.0.53current
acAMSProcedureResult
NOTIFICATION-TYPE
AMS procedure related information
1.3.6.1.4.1.5003.9.10.1.21.2.0.54current
acWeakRedundancy
NOTIFICATION-TYPE
The system is in weak redundancy mode. Switch over is done with a reset to the board taking over.
1.3.6.1.4.1.5003.9.10.1.21.2.0.55current
acTMInconsistentRemoteAndLocalPLLStatus
NOTIFICATION-TYPE
Inconsistent Remote And Local PLL Status
1.3.6.1.4.1.5003.9.10.1.21.2.0.56current
acTMReferenceStatus
NOTIFICATION-TYPE
Timing manager reference status
1.3.6.1.4.1.5003.9.10.1.21.2.0.57current
acTMReferenceChange
NOTIFICATION-TYPE
Timing manager reference Change
1.3.6.1.4.1.5003.9.10.1.21.2.0.58current
acGWSASEmergencyModeAlarm
NOTIFICATION-TYPE
The alarm is raised when SAS enters the Emergency Mode and then cleared when SAS enters Normal Mode again.
1.3.6.1.4.1.5003.9.10.1.21.2.0.59current
acV52InterfaceAlarm
NOTIFICATION-TYPE
The alarm is raised for v5.2 interface errors and alarms.{@}For a detailed list of the interfaces' alarms see the acV5InterfceTable.
1.3.6.1.4.1.5003.9.10.1.21.2.0.60current
acSonetPathSTSLOPAlarm
NOTIFICATION-TYPE
Sonet Path STS LOP alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.61current
acSonetPathSTSAISAlarm
NOTIFICATION-TYPE
Sonet Path STS AIS alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.62current
acSonetPathSTSRDIAlarm
NOTIFICATION-TYPE
Sonet Path STS RDI alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.63current
acSonetPathUnequippedAlarm
NOTIFICATION-TYPE
Sonet Path Unequipped alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.64current
acSonetPathSignalLabelMismatchAlarm
NOTIFICATION-TYPE
Sonet Path Signal Label Mismatch alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.65current
acDS3RAIAlarm
NOTIFICATION-TYPE
DS3 RAI alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.66current
acDS3AISAlarm
NOTIFICATION-TYPE
DS3 AIS alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.67current
acDS3LOFAlarm
NOTIFICATION-TYPE
DS3 LOF alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.68current
acDS3LOSAlarm
NOTIFICATION-TYPE
DS3 LOS alarm.
1.3.6.1.4.1.5003.9.10.1.21.2.0.69current
acSWUpgradeAlarm
NOTIFICATION-TYPE
Raised for SW upgrade process errors.
1.3.6.1.4.1.5003.9.10.1.21.2.0.70current
acNTPServerStatusAlarm
NOTIFICATION-TYPE
NTP server status alarm. {@}Raised when the connection to the NTP server is lost. Cleared when the connection is reestablished. {@}Unset time (as a result of no connection to NTP server) may result with functionality degradation and failure in device.
1.3.6.1.4.1.5003.9.10.1.21.2.0.71current
acThreeWayConferenceOutOfResources
NOTIFICATION-TYPE
Three way conference out of resources.
1.3.6.1.4.1.5003.9.10.1.21.2.0.72current
acSS7AliasPcStateChangeAlarm
NOTIFICATION-TYPE
raised when the Alias PC is in BUSY state. Cleared when it is in In-Service state.
1.3.6.1.4.1.5003.9.10.1.21.2.0.73current
acSS7UalGroupStateChangeAlarm
NOTIFICATION-TYPE
Raised when the Ual Group Asp state is not ACTIVE. Cleared when it is Active.
1.3.6.1.4.1.5003.9.10.1.21.2.0.74current
acLDAPLostConnection
NOTIFICATION-TYPE
Raised when there is no connection to the LDAP server.
1.3.6.1.4.1.5003.9.10.1.21.2.0.75current
acAnalogPortGroundFaultOutOfService
NOTIFICATION-TYPE
Raised when the MP500 FXS port is inactive due to ground fault.
1.3.6.1.4.1.5003.9.10.1.21.2.0.76current
acSSHConnectionStatus
NOTIFICATION-TYPE
This trap indicates the result of a recent SSH connection attempt.
1.3.6.1.4.1.5003.9.10.1.21.2.0.77current
acOCSPServerStatusAlarm
NOTIFICATION-TYPE
raised when OCSP connection is not available.
1.3.6.1.4.1.5003.9.10.1.21.2.0.78current
acBoardWanLinkAlarm
NOTIFICATION-TYPE
Wan Link is down.
1.3.6.1.4.1.5003.9.10.1.21.2.0.79current
acPowerOverEthernetStatus
NOTIFICATION-TYPE
Raised when PEO resources are over allocated
1.3.6.1.4.1.5003.9.10.1.21.2.0.80current
acMediaProcessOverloadAlarm
NOTIFICATION-TYPE
Raised when media process overloads
1.3.6.1.4.1.5003.9.10.1.21.2.0.81current
acWirelessCellularModemAlarm
NOTIFICATION-TYPE
Raised when either the wireless modem is down or in backup mode.
1.3.6.1.4.1.5003.9.10.1.21.2.0.82current
acDataInterfaceStatus
NOTIFICATION-TYPE
Raised when a DSL interface state changes to up or down.
1.3.6.1.4.1.5003.9.10.1.21.2.0.83current
acNFASGroupAlarm
NOTIFICATION-TYPE
Raised when an NFAS group goes Out-Of-Service
1.3.6.1.4.1.5003.9.10.1.21.2.0.84current
acBChannelAlarm
NOTIFICATION-TYPE
Raised when B-Channel service state changes
1.3.6.1.4.1.5003.9.10.1.21.2.0.85current
acEthernetGroupAlarm
NOTIFICATION-TYPE
Raised when the Ethernet group has no Ethernet port with its link up. Cleared when at least on port has established a link.
1.3.6.1.4.1.5003.9.10.1.21.2.0.86current
acMediaRealmBWThresholdAlarm
NOTIFICATION-TYPE
Raised when a BW threshold is crossed
1.3.6.1.4.1.5003.9.10.1.21.2.0.87current
acNqmConnectivityAlarm
NOTIFICATION-TYPE
Connectivity with NQM probe destination is lost
1.3.6.1.4.1.5003.9.10.1.21.2.0.88current
acNqmRttAlarm
NOTIFICATION-TYPE
Detected high Round Trip Time towards NQM probe destination
1.3.6.1.4.1.5003.9.10.1.21.2.0.89current
acNqmJitterAlarm
NOTIFICATION-TYPE
Detected high Jitter towards NQM probe destination
1.3.6.1.4.1.5003.9.10.1.21.2.0.90current
acNqmPacketLossAlarm
NOTIFICATION-TYPE
Detected high Packet Loss towards NQM probe destination
1.3.6.1.4.1.5003.9.10.1.21.2.0.91current
acCertificateExpiryNotifiaction
NOTIFICATION-TYPE
Send before the expiration of the installed credentials, which cannot be renewed automatically.
1.3.6.1.4.1.5003.9.10.1.21.2.0.92current
acWEBUserAccessDisabled
NOTIFICATION-TYPE
Web user was disabled due to inactivity.
1.3.6.1.4.1.5003.9.10.1.21.2.0.93current
acProxyConnectionLost
NOTIFICATION-TYPE
Raised when all connections in the proxy set are down.
1.3.6.1.4.1.5003.9.10.1.21.2.0.94current
acNqmCqMosAlarm
NOTIFICATION-TYPE
Detected low conversational voice quality towards NQM probe destination
1.3.6.1.4.1.5003.9.10.1.21.2.0.95current
acNqmLqMosAlarm
NOTIFICATION-TYPE
Detected low listening voice quality towards NQM probe destination
1.3.6.1.4.1.5003.9.10.1.21.2.0.96current
acRedundantBoardAlarm
NOTIFICATION-TYPE
Active board sends notification when an alarm or notification is raised in the redundant board. The information is as follow: acBoardTrapGlobalsAdditionalInfo1: redundant’s original info acBoardTrapGlobalsAdditionalInfo2: trap Id acBoardTrapGlobalsAdditionalInfo3: redundant’s serial number
1.3.6.1.4.1.5003.9.10.1.21.2.0.97current
acHANetworkWatchdogStatusAlarm
NOTIFICATION-TYPE
Sent when the module was enabled by the user but it is not running.
1.3.6.1.4.1.5003.9.10.1.21.2.0.98current
acIDSPolicyAlarm
NOTIFICATION-TYPE
IDS Policy Alarm
1.3.6.1.4.1.5003.9.10.1.21.2.0.99current
acIDSThresholdCrossNotification
NOTIFICATION-TYPE
Sent when IDS Threshold is crossed
1.3.6.1.4.1.5003.9.10.1.21.2.0.100current