MIBs Depot

ATSWTCH2-MIB

Registered at
1.3.6.1.4.1.207.8.10
Namespace
allied
Source file
ATSWTCH2-MIB
Digest
sha256:01b0ff2d9cde22e0616b1e4eb9c9a132b305192352bf05c95a929be413ca8583

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ATSWTCH2-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
BridgeId
type
MacAddress
type
Timeout
type

Objects

NameOIDSyntaxAccessStatus
alliedTelesyn
OBJECT-IDENTITY
1.3.6.1.4.1.207
atiProduct
OBJECT-IDENTITY
1.3.6.1.4.1.207.1
mibObject
OBJECT-IDENTITY
1.3.6.1.4.1.207.8
atswitchMib
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10
atswitchSysGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.1
atswitchProductType
OBJECT-TYPE
This object will return Product Type.
1.3.6.1.4.1.207.8.10.1.1INTEGER {at-3726(1), at-3714(2), at-8124XL(3), at-8118(4), at-3726XL(5), at-3714FXL(6), at-3716XL(7), other(10)}read-onlymandatory
atswitchEthernetPortCount
OBJECT-TYPE
This object will return the number of 10/100 Mbps Ethernet ports on the switch.
1.3.6.1.4.1.207.8.10.1.2INTEGERread-onlymandatory
atswitchReset
OBJECT-TYPE
Setting this object to 'switch-reset' will cause the switch to perform a hardware reset within approximately 4-6 seconds. Setting this object to 'switch-no-reset will have no effect. The value 'no-reset' will be returned whenever this object is retrieved.
1.3.6.1.4.1.207.8.10.1.3INTEGER {switch-no-reset(1), switch-reset(2)}read-writemandatory
atswitchMDA1Type
OBJECT-TYPE
This object returns the MDA type of the Uplink port
1.3.6.1.4.1.207.8.10.1.4INTEGER {rj45-mii(1), fiber(2), none(3)}read-onlymandatory
atswitchMDA2Type
OBJECT-TYPE
This Object is supported in 81XX product line only. This object returns the MDA type of the Uplink Port named 'B'. It returns 'none' if a 'B' MDA slot is not installed.
1.3.6.1.4.1.207.8.10.1.5INTEGER {rj45-mii(1), fiber(2), none(3)}read-onlymandatory
atswitchDeviceFlowControl
OBJECT-TYPE
This Object is supported on 81XX products only. This object configures the Flow Control of the Device
1.3.6.1.4.1.207.8.10.1.6INTEGER {enable(1), disable(2)}read-writemandatory
atswitchSwGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.1.7
atswitchSwProduct
OBJECT-TYPE
Identifies the software product the device is running.
1.3.6.1.4.1.207.8.10.1.7.1DisplayString (SIZE(0..255))read-onlymandatory
atswitchSwVersion
OBJECT-TYPE
Identifies the version number of the present release.
1.3.6.1.4.1.207.8.10.1.7.2DisplayString (SIZE(0..255))read-onlymandatory
atswitchIpGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.1.8
atswitchCurrentIpAddress
OBJECT-TYPE
The Current IP address is the one which is currently used and is obtained dynamically through one of the protocols interaction.( DHCP or Bootp.) This address is NULL if the Address is Statically configured.
1.3.6.1.4.1.207.8.10.1.8.1IpAddressread-onlymandatory
atswitchConfiguredIpAddress
OBJECT-TYPE
The Configured IP address of the device. This is the address configured through Network or Local Omega.
1.3.6.1.4.1.207.8.10.1.8.2IpAddressread-writemandatory
atswitchConfiguredSubnetMask
OBJECT-TYPE
The Configured Subnet Mask of the device.
1.3.6.1.4.1.207.8.10.1.8.3IpAddressread-writemandatory
atswitchConfiguredRouter
OBJECT-TYPE
The Configured Gateway/Router address of the device
1.3.6.1.4.1.207.8.10.1.8.4IpAddressread-writemandatory
atswitchIPAddressStatus
OBJECT-TYPE
The IP Address can be obtained/configured by any of the above different ways. This object specifies how IP address currently on the switch Box, was configured/obtained.
1.3.6.1.4.1.207.8.10.1.8.5INTEGER {from-dhcp(1), from-bootp(2), from-psuedoip(3), from-Omega(4)}read-onlymandatory
atswitchDNServer
OBJECT-TYPE
The Configured DNS Server address of the device
1.3.6.1.4.1.207.8.10.1.8.6IpAddressread-writemandatory
atswitchDefaultDomainName
OBJECT-TYPE
This Object defines the Default Domain where this switch can be belong to.
1.3.6.1.4.1.207.8.10.1.8.7DisplayString (SIZE(0..255))read-writemandatory
atswitchNMGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.1.9
atswitchNwMgrTable
OBJECT-TYPE
A list of SNMP Trap Manager stations Entries. The number of entries is given by the switchNwMgrTotal mib object.
1.3.6.1.4.1.207.8.10.1.9.1not-accessiblemandatory
atswitchNwMgrEntry
OBJECT-TYPE
Trap receipt Manager Entry containing ipaddress of the configured NMS's to which Traps are sent.
1.3.6.1.4.1.207.8.10.1.9.1.1not-accessiblemandatory
atswitchNwMgrIndex
OBJECT-TYPE
The Index of the Managers Ip address.
1.3.6.1.4.1.207.8.10.1.9.1.1.1INTEGER (1..4)read-onlymandatory
atswitchNwMgrIpAddr
OBJECT-TYPE
The IP Address of the NMS host configured.
1.3.6.1.4.1.207.8.10.1.9.1.1.2IpAddressread-writemandatory
atswitchConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.2
atswitchPortDisableOnSecurityViolation
OBJECT-TYPE
This System wide attribute allows the port to be disabled on Violation of the Security. or suspend the port due to Duplicate Address. Needs More explaination after somebody figures out whether atswitch needs the suspend state.
1.3.6.1.4.1.207.8.10.2.1INTEGER {disable-on-security-voilation(1), suspend-on-double-address(2), security-not-yet-initalized(3)}read-writemandatory
atswitchMirroringSourcePort
OBJECT-TYPE
This is the Source port number for which there is another mirror port.If the atswitchEthConfigMirrorState is Enabled then ,the mirror portgets routed with all the packets going in and out of Source port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Source port. One of the port is dedicated to this so that for any port as source port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled. For the AT-81XX only the receive activity can be mirrored.
1.3.6.1.4.1.207.8.10.2.2INTEGERread-writemandatory
atswitchMirrorState
OBJECT-TYPE
if the state of Mirroring is enabled by selecting one of the first three values , then the Mirroring explained above works. If disabled, port operation works normally. No Traffic gets routed from MirroringSourcePort to Destination Mirrored Port. Mirroring of both transmit and receive activity can only be done if the port is half duplex. Choose both only if you know the port will be run in half duplex mode.
1.3.6.1.4.1.207.8.10.2.3INTEGER {receive(1), transmit(2), both(3), disabled(4)}read-writemandatory
atswitchMirroringDestinationPort
OBJECT-TYPE
This is the Destination port number for which there is another mirror port.If the atswitchEthConfigMirrorState is Enabled then ,the mirror portgets routed with all the packets going in and out of Destination port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Destination port. One of the port is dedicated to this so that for any port as destination port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled. For the AT-81XX only the receive activity can be mirrored.
1.3.6.1.4.1.207.8.10.2.4INTEGERread-writemandatory
atswitchSecurityConfig
OBJECT-TYPE
This Object is suppported only in 37XX product Line. Security feature configuration Object. The Security disable would let the device carry on the learn-new-address-as-it-comes-in mode as usual. When security is enabled-with-learning-locked, the learning of new address is stopped and the addresses locked in the device is used as the security Database. If an address comes in which is not present in the Device Security Database, then any of the atswitchSecurityAction Configured is triggered. When limited-enabled is selected, a per-port atswitchPortSecurityNumberOfAddresses specify the max number of MACs to be learned .
1.3.6.1.4.1.207.8.10.2.5INTEGER {disabled(1), enabled-with-learning-locked(2), limited-enabled(3)}read-writemandatory
atswitchSecurityAction
OBJECT-TYPE
Security Action to be carried when the atswitchSecurityConfig is enabled-with-learning-locked or limted-enabled.
1.3.6.1.4.1.207.8.10.2.6INTEGER {send-trap-only(1), disable-port-only(2), disable-port-and-send-trap(3), do-nothing(4)}read-writemandatory
atswitchDebugAvailableBytes
OBJECT-TYPE
This is strictly for Debug reason and this object should not be beleived as the correct number
1.3.6.1.4.1.207.8.10.2.7INTEGERread-onlymandatory
atswitchTrunkConfig
OBJECT-TYPE
This Object Configures the Trunking for the Uplink Ports only. This feature is currently available only in Fenix 37XX-XL hardware.
1.3.6.1.4.1.207.8.10.2.8INTEGER {enable(1), disable(2)}read-writemandatory
atswitchPortConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.3
atswitchPortTable
OBJECT-TYPE
Table of basic port configuration information.
1.3.6.1.4.1.207.8.10.3.1not-accessiblemandatory
atswitchPortEntry
OBJECT-TYPE
An entry in the port config table.
1.3.6.1.4.1.207.8.10.3.1.1not-accessiblemandatory
atswitchPortNumber
OBJECT-TYPE
This object identifies the port of the switch.
1.3.6.1.4.1.207.8.10.3.1.1.1INTEGERread-onlymandatory
atswitchPortName
OBJECT-TYPE
This attribute associates a user defined string name with the port.
1.3.6.1.4.1.207.8.10.3.1.1.2DisplayString (SIZE(0..20))read-writemandatory
atswitchPortAutosenseOrHalfDuplex
OBJECT-TYPE
This attribute allows an administrative request to configure whether this port can Autosense or Force the Half Duplex
1.3.6.1.4.1.207.8.10.3.1.1.3INTEGER {portAutoSense(1), forceHalfDuplex(2)}read-writemandatory
atswitchPortLinkState
OBJECT-TYPE
This attribute allows an administrative request to read the status of link state on this port.
1.3.6.1.4.1.207.8.10.3.1.1.4INTEGER {online(1), offline(2)}read-onlymandatory
atswitchPortDuplexStatus
OBJECT-TYPE
This attribute allows an administrative request to read the status of Duplex on this port.
1.3.6.1.4.1.207.8.10.3.1.1.5INTEGER {fullDuplex(1), halfDuplex(2)}read-onlymandatory
atswitchPortSpeed
OBJECT-TYPE
This attribute allows an administrative request to read/write the speed of this port. This attribure is read-only for all the Ports on AT-37XX product . This Attribute is read-write for ATS21 (AT81XX) product Only. This attribute allows an administrative request to change the speed on ATS21 product.
1.3.6.1.4.1.207.8.10.3.1.1.6INTEGER {tenMBits(1), hundredMBits(2)}read-writemandatory
atswitchPortState
OBJECT-TYPE
This attribute allows an administrative request to disable or enable communications on this port.It also responds with the status of the port .Except enabled(1) and disabled(2), all values are read-only status.
1.3.6.1.4.1.207.8.10.3.1.1.7INTEGER {enabled(1), disabled(2), blocking(3), listening(4), learning(5)}read-writemandatory
atswitchPortTransmitPacingConfig
OBJECT-TYPE
This Object is supported on AT36XX product line Only. This attribute allows the transmit Pacing to be enabled or disabled.
1.3.6.1.4.1.207.8.10.3.1.1.8INTEGER {enable(1), disable(2)}read-writemandatory
atswitchPortSTPConfig
OBJECT-TYPE
This attribute allows a bridging Mode to be configured with either Spanning Tree enabled or disabled. When Spanning tree is enabled, make sure that this port is belonging to a valid Bridge_id. Spanning Tree is enabled only when a valid Bridge_id is set.
1.3.6.1.4.1.207.8.10.3.1.1.9INTEGER {enable(1), disable(2)}read-writemandatory
atswitchPortBridgeid
OBJECT-TYPE
The Bridge to which this port belongs to .
1.3.6.1.4.1.207.8.10.3.1.1.10INTEGER (1..64)read-writemandatory
atswitchPortSTPCost
OBJECT-TYPE
The Cost of the Spanning Tree Protocol.This object is valid only when STP is enabled.
1.3.6.1.4.1.207.8.10.3.1.1.11INTEGER (0..65535)read-writemandatory
atswitchPortSTPPriority
OBJECT-TYPE
The Priority of the spanning Tree Protocol. This object is valid when STP is enabled.
1.3.6.1.4.1.207.8.10.3.1.1.12INTEGER (0..255)read-writemandatory
atswitchPortSwitchingType
OBJECT-TYPE
This per-port attribute describes whether the port identified by atswitchPortNumber uses store-and-forward bridging for local switched Ethernet packets or cut-through. The Hardware allows cut-through on Transmission and cut-through-on Receive and the same for the store-and-forward. But some of the Config option does not make any sense. So, for now there is no distiction of Rx and Tx. Both Tx/Rx support store-and-forward or cut-through. This Object is not applicable for 37XX with XL hardware as the Hardware does not support both Cut through and Store and Forward. It is default Store and Forward. Even though the Set on either of them is done, Hardware does not do the Cut through Switching.
1.3.6.1.4.1.207.8.10.3.1.1.13INTEGER {fast-cut-through(1), store-and-forward(2)}read-writemandatory
atswitchPortFlowControlEnable
OBJECT-TYPE
This Per_port attribute is only for ATS21 product.(81XX). This per-port attribute describes whether the port identified has flow Control Enabled or not. Flow Control on Full Duplex and Half Duplex is detected and Automatically, flow control accordingly is taken care of. BY Default, Flow Control is Disabled.
1.3.6.1.4.1.207.8.10.3.1.1.14INTEGER {disable(1), enable(2)}read-writedeprecated
atswitchPortSecurityNumberOfAddresses
OBJECT-TYPE
This object configures the Max number of addresses at an instance to be learnt by the device. If the learnt addresses number is above this number, then the atswitchSecurityAction is triggered . when the number of learnt addresses exceeds this number ,the the atswitchSecurityAction is triggered only if atswitchSecurityConfig is set to limited-enalbled. ELse nothing is triggered.
1.3.6.1.4.1.207.8.10.3.1.1.15INTEGERread-writemandatory
atswitchVlanConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.4
atswitchBasicVlanTable
OBJECT-TYPE
Table of Virtual LAN configured.
1.3.6.1.4.1.207.8.10.4.1not-accessiblemandatory
atswitchBasicVlanEntry
OBJECT-TYPE
An entry in the table, containing VLAN information.
1.3.6.1.4.1.207.8.10.4.1.1not-accessiblemandatory
atswitchBeVlanIndex
OBJECT-TYPE
This object identifies the VLAN.
1.3.6.1.4.1.207.8.10.4.1.1.1INTEGER (1..64)read-onlymandatory
atswitchBeVlanName
OBJECT-TYPE
This attribute associates a user defined string with the Virtual LAN. To configure a new VLAN, do 'set' operation on this object with the VLAN name. To delete an VLAN, do 'set' operation with string '*'. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
1.3.6.1.4.1.207.8.10.4.1.1.2DisplayString (SIZE(0..20))read-writemandatory
atswitchBeVlanTagId
OBJECT-TYPE
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This object configures the VId in the Tag Information header in accordance with 802.1q spec. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
1.3.6.1.4.1.207.8.10.4.1.1.3INTEGER (1..4095)read-writemandatory
atswitchBeVlanPortMask
OBJECT-TYPE
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This Object builds the Output Ports that participate in the Vlan with the atswitchBeVlanName. The Format of the input string would be like '1,2,5,7,12'. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
1.3.6.1.4.1.207.8.10.4.1.1.4DisplayStringread-writemandatory
atswitchBeVlanRowStatus
OBJECT-TYPE
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This object identifies the atswitchBeVLANEntry Row Status . The User sets this object to under-construction, to start with to create a row. Once the User Configures the VlanName and TagId and also the Output Ports.This object should be set to operational. If the user does not set this object to operational, the whole row is lost .when a 'get' of this row is done, this uncommited row is not seen. configured in the switch.
1.3.6.1.4.1.207.8.10.4.1.1.5INTEGER {idle(1), operational(2), under-construction(3), not-operational(4)}read-writemandatory
atswitchPort2VlanTable
OBJECT-TYPE
Table of per port Virtual LAN configuration.
1.3.6.1.4.1.207.8.10.4.2not-accessiblemandatory
atswitchPort2VlanEntry
OBJECT-TYPE
An entry in the table, containing per port VLAN information.
1.3.6.1.4.1.207.8.10.4.2.1not-accessiblemandatory
atswitchPvPortNumber
OBJECT-TYPE
This object identifies the port on the switch.
1.3.6.1.4.1.207.8.10.4.2.1.1INTEGERread-onlymandatory
atswitchPvVlanName
OBJECT-TYPE
This attribute associates a user defined string with the Virtual LAN. This Object is the same as atswitchBeVlanName. Please make sure to give the same string as atswitchBeVlanName.
1.3.6.1.4.1.207.8.10.4.2.1.2DisplayStringread-writemandatory
atswitchEthernetStatsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.5
atswitchEthMonStats
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.5.1
atswitchEthMonRxGoodFrames
OBJECT-TYPE
The total number of Good Frames received on this module.
1.3.6.1.4.1.207.8.10.5.1.1Counterread-onlymandatory
atswitchEthMonTxGoodFrames
OBJECT-TYPE
The total number of Good Frames Transmitted by this module.
1.3.6.1.4.1.207.8.10.5.1.2Counterread-onlymandatory
atswitchEthMonTxTotalBytes
OBJECT-TYPE
The total number of Bytes transmitted from this module.
1.3.6.1.4.1.207.8.10.5.1.3Counterread-onlymandatory
atswitchEthMonTxDeferred
OBJECT-TYPE
This is the count of first time Transmission attempt which failed on an interface due to medium being busy.
1.3.6.1.4.1.207.8.10.5.1.4Counterread-onlymandatory
atswitchEthMonTxCollisions
OBJECT-TYPE
The total number of collisions while switching on an interface.
1.3.6.1.4.1.207.8.10.5.1.5Counterread-onlymandatory
atswitchEthErrorStats
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.5.2
atswitchEthErrorCRC
OBJECT-TYPE
The total number of CRC errors on received packets.
1.3.6.1.4.1.207.8.10.5.2.1Counterread-onlymandatory
atswitchEthErrorAlignment
OBJECT-TYPE
The total number of packets received that has alignment errors
1.3.6.1.4.1.207.8.10.5.2.2Counterread-onlymandatory
atswitchEthErrorRxBadFrames
OBJECT-TYPE
The counter is incremented when a bad frame was received.
1.3.6.1.4.1.207.8.10.5.2.3Counterread-onlymandatory
atswitchEthErrorLateCollisions
OBJECT-TYPE
This object counts the number of times the collison was detected in the port.
1.3.6.1.4.1.207.8.10.5.2.4Counterread-onlymandatory
atswitchEthErrorTxTotal
OBJECT-TYPE
Total number of error resulted from transfer operations.
1.3.6.1.4.1.207.8.10.5.2.6Counterread-onlymandatory
atswitchEthPortStatsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.6
atswitchEthPortMonStats
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.6.1
atswitchEthPortMonTable
OBJECT-TYPE
A list of statistics entries.
1.3.6.1.4.1.207.8.10.6.1.1not-accessiblemandatory
atswitchEthPortMonEntry
OBJECT-TYPE
A collection of statistics kept for a particular port.
1.3.6.1.4.1.207.8.10.6.1.1.1not-accessiblemandatory
atswitchEthPortMonId
OBJECT-TYPE
The relative position of a port within a switch starting with 1.
1.3.6.1.4.1.207.8.10.6.1.1.1.1INTEGERread-onlymandatory
atswitchEthPortMonTxTotalBytes
OBJECT-TYPE
The total number of Bytes transmited to this port.
1.3.6.1.4.1.207.8.10.6.1.1.1.2Counterread-onlymandatory
atswitchRxGoodFrames
OBJECT-TYPE
The total number of good packets(including unicast,broadcast packets and multicast packets) received
1.3.6.1.4.1.207.8.10.6.1.1.1.3Counterread-onlymandatory
atswitchTxGoodFrames
OBJECT-TYPE
The total number of good packets(including bad packets, broadcast packets and multicast packets) transmitted successfully
1.3.6.1.4.1.207.8.10.6.1.1.1.4Counterread-onlymandatory
atswitchTxBroadcastFrames
OBJECT-TYPE
The total number of packets transmitted that were directed to the broadcast address. This does not include multicast packets
1.3.6.1.4.1.207.8.10.6.1.1.1.5Counterread-onlymandatory
atswitchTxMulticastFrames
OBJECT-TYPE
The total number of packets transmitted that were directed to a multicast address. This does not include packets addressed to the broadcast address
1.3.6.1.4.1.207.8.10.6.1.1.1.6Counterread-onlymandatory
atswitchAddrDuplicate
OBJECT-TYPE
The number of address duplications seen on this port which is secured on another port. If a source address is locked for a port and if that address is eeen as source address on this port, then such occurances of duplicate Address is noted.
1.3.6.1.4.1.207.8.10.6.1.1.1.7Counterread-onlymandatory
atswitchAddrMismatches
OBJECT-TYPE
Address mismatches /address changes the sum of : 1. The number of mismatches seen on a port between a securely assigned port address and the source address observed on the port. Occurrence of this causes the TNETX3150 to suspend the port. 2. The number of times the TNETX3150 is required to assign or learn an address for a port.
1.3.6.1.4.1.207.8.10.6.1.1.1.8Counterread-onlymandatory
atswitchRxOverruns
OBJECT-TYPE
The number of frames lost due to lack of resources during frame reception. The counter is incremented when frame data cannot enter the RX fifo for whatever reason. Frames that overrun after entering the fifo also can be counted as RX discards if they are not cut-through.
1.3.6.1.4.1.207.8.10.6.1.1.1.9Counterread-onlymandatory
atswitchEthPortError
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.6.2
atswitchEthPortErrorTable
OBJECT-TYPE
A list of statistics entries.
1.3.6.1.4.1.207.8.10.6.2.1not-accessiblemandatory
atswitchEthPortErrorEntry
OBJECT-TYPE
A collection of statistics kept for a particular port.
1.3.6.1.4.1.207.8.10.6.2.1.1not-accessiblemandatory
atswitchEthPortErrorId
OBJECT-TYPE
The relative position of a port within a switch starting with 1.
1.3.6.1.4.1.207.8.10.6.2.1.1.1INTEGERread-onlymandatory
atswitchEthPortErrorRxBadFrames
OBJECT-TYPE
The counter is incremented when a bad frame was received on this port.
1.3.6.1.4.1.207.8.10.6.2.1.1.2Counterread-onlymandatory
atswitchEthPortErrorTxTotal
OBJECT-TYPE
Total number of error resulted from transmit operations on this port.
1.3.6.1.4.1.207.8.10.6.2.1.1.3Counterread-onlymandatory
atswitchFwdVlanGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.7
atswitchFwdVlanTable
OBJECT-TYPE
This tables lists Mac Addresses lexicographically from the forwarding table and also the information about the Vlan/Vlan which this MAC address belongs to.
1.3.6.1.4.1.207.8.10.7.1not-accessiblemandatory
atswitchFwdVlanEntry
OBJECT-TYPE
Entry in the atswitchFwdVlanTable.
1.3.6.1.4.1.207.8.10.7.1.1not-accessiblemandatory
atswitchFwdVlanMACAddr
OBJECT-TYPE
This object identifies the MAC Address associated with this entry.
1.3.6.1.4.1.207.8.10.7.1.1.1MacAddressread-onlymandatory
atswitchFwdVlanVlanId
OBJECT-TYPE
This object identifies the Vlan/Vlan which MAC Address defined by the atswitchFwdMACAddr is associated with.
1.3.6.1.4.1.207.8.10.7.1.1.2INTEGERread-onlymandatory
atswitchFwdVlanAge
OBJECT-TYPE
Current Age of the MACAddr in the Forwarding Table.It Starts with 0 and if not heard it increments to some value until it hears from it and if not heard before reaching Max value, it will purge this entry.
1.3.6.1.4.1.207.8.10.7.1.1.3INTEGERread-onlymandatory
atswitchFwdVlanStatus
OBJECT-TYPE
The status of this entry. The meanings of the values are: inactive(1) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. active(2) : the value of the corresponding instance of atswitchFwdVlanPort was active, and is being used. other(3) : none of the following.
1.3.6.1.4.1.207.8.10.7.1.1.4INTEGER {inactive(1), active(2), other(3)}read-onlymandatory
atswitchFwdVlanPort
OBJECT-TYPE
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of atswitchFwdVlanMACAddr has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address. Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of atswitchFwdVlanStatus is not learned(3).
1.3.6.1.4.1.207.8.10.7.1.1.5INTEGERread-onlymandatory
atswitchTrapAttrGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.8
atswitchDuplicateMacAddress
OBJECT-TYPE
The Duplicate Mac address which is secured on atswitchSecurePortNumber.
1.3.6.1.4.1.207.8.10.8.1OCTET STRING (SIZE(6))not-accessiblemandatory
atswitchIntruderMacAddress
OBJECT-TYPE
The Mac address of the Intruder as seen on port which is the the next object
1.3.6.1.4.1.207.8.10.8.2OCTET STRING (SIZE(6))not-accessiblemandatory
atswitchSecuredPortNumber
OBJECT-TYPE
This is the Port number which has the duplicate Address as the secured address .
1.3.6.1.4.1.207.8.10.8.3INTEGERnot-accessiblemandatory
atswitchBridgeMib
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.9
atswitchBrBase
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.9.1
atswitchBrBaseTable
OBJECT-TYPE
Table of basic bridge information.
1.3.6.1.4.1.207.8.10.9.1.1not-accessiblemandatory
atswitchBrBaseEntry
OBJECT-TYPE
An entry in the atswitchBrBaseTable.
1.3.6.1.4.1.207.8.10.9.1.1.1not-accessiblemandatory
atswitchBrBaseLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.1.1.1.1INTEGERread-onlymandatory
atswitchBrBaseBridgeAddress
OBJECT-TYPE
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with atswitchBrStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
1.3.6.1.4.1.207.8.10.9.1.1.1.2MacAddressread-onlymandatory
atswitchBrBaseNumPorts
OBJECT-TYPE
The number of ports controlled by this bridging entity.
1.3.6.1.4.1.207.8.10.9.1.1.1.3INTEGERread-onlymandatory
atswitchBrBaseType
OBJECT-TYPE
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
1.3.6.1.4.1.207.8.10.9.1.1.1.4INTEGER {unknown(1), transparent-only(2), sourceroute-only(3), srt(4)}read-onlymandatory
atswitchBrBasePortTable
OBJECT-TYPE
A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included.
1.3.6.1.4.1.207.8.10.9.1.4not-accessiblemandatory
atswitchBrBasePortEntry
OBJECT-TYPE
A list of information for each port of the bridge.
1.3.6.1.4.1.207.8.10.9.1.4.1not-accessiblemandatory
atswitchBrBasePortLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.1.4.1.1INTEGERread-onlymandatory
atswitchBrBasePort
OBJECT-TYPE
The port number of the port for which this entry contains bridge management information.
1.3.6.1.4.1.207.8.10.9.1.4.1.2INTEGER (1..65535)read-onlymandatory
atswitchBrBasePortIfIndex
OBJECT-TYPE
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
1.3.6.1.4.1.207.8.10.9.1.4.1.3INTEGERread-onlymandatory
atswitchBrBasePortCircuit
OBJECT-TYPE
For a port which (potentially) has the same value of atswitchBrBasePortIfIndex as another port on the same bridge, this object contains the name of an object instance unique to this port. For example, in the case where multiple ports correspond one- to-one with multiple X.25 virtual circuits, this value might identify an (e.g., the first) object instance associated with the X.25 virtual circuit corresponding to this port. For a port which has a unique value of atswitchBrBasePortIfIndex, this object can have the value { 0 0 }.
1.3.6.1.4.1.207.8.10.9.1.4.1.4OBJECT IDENTIFIERread-onlymandatory
atswitchBrBasePortDelayExceededDiscards
OBJECT-TYPE
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
1.3.6.1.4.1.207.8.10.9.1.4.1.5Counterread-onlymandatory
atswitchBrBasePortMtuExceededDiscards
OBJECT-TYPE
The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges.
1.3.6.1.4.1.207.8.10.9.1.4.1.6Counterread-onlymandatory
atswitchBrStp
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.9.2
atswitchBrStpTable
OBJECT-TYPE
Table of bridge spanning tree information.
1.3.6.1.4.1.207.8.10.9.2.1not-accessiblemandatory
atswitchBrStpEntry
OBJECT-TYPE
An entry in the atswitchBrStpTable.
1.3.6.1.4.1.207.8.10.9.2.1.1not-accessiblemandatory
atswitchBrStpLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.2.1.1.1INTEGERread-onlymandatory
atswitchBrStpProtocolSpecification
OBJECT-TYPE
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
1.3.6.1.4.1.207.8.10.9.2.1.1.2INTEGER {unknown(1), decLb100(2), ieee8021d(3)}read-onlymandatory
atswitchBrStpPriority
OBJECT-TYPE
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of atswitchBrBaseBridgeAddress.
1.3.6.1.4.1.207.8.10.9.2.1.1.3INTEGER (0..65535)read-writemandatory
atswitchBrStpTimeSinceTopologyChange
OBJECT-TYPE
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
1.3.6.1.4.1.207.8.10.9.2.1.1.4TimeTicksread-onlymandatory
atswitchBrStpTopChanges
OBJECT-TYPE
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
1.3.6.1.4.1.207.8.10.9.2.1.1.5Counterread-onlymandatory
atswitchBrStpDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.207.8.10.9.2.1.1.6BridgeIdread-onlymandatory
atswitchBrStpRootCost
OBJECT-TYPE
The cost of the path to the root as seen from this bridge.
1.3.6.1.4.1.207.8.10.9.2.1.1.7INTEGERread-onlymandatory
atswitchBrStpRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.207.8.10.9.2.1.1.8INTEGERread-onlymandatory
atswitchBrStpMaxAge
OBJECT-TYPE
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.207.8.10.9.2.1.1.9Timeoutread-onlymandatory
atswitchBrStpHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.207.8.10.9.2.1.1.10Timeoutread-onlymandatory
atswitchBrStpHoldTime
OBJECT-TYPE
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
1.3.6.1.4.1.207.8.10.9.2.1.1.11INTEGERread-onlymandatory
atswitchBrStpForwardDelay
OBJECT-TYPE
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to atswitchBrStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
1.3.6.1.4.1.207.8.10.9.2.1.1.12Timeoutread-onlymandatory
atswitchBrStpBridgeMaxAge
OBJECT-TYPE
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atswitchBrStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
1.3.6.1.4.1.207.8.10.9.2.1.1.13Timeout (600..4000)read-writemandatory
atswitchBrStpBridgeHelloTime
OBJECT-TYPE
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
1.3.6.1.4.1.207.8.10.9.2.1.1.14Timeout (100..1000)read-writemandatory
atswitchBrStpBridgeForwardDelay
OBJECT-TYPE
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atswitchBrStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
1.3.6.1.4.1.207.8.10.9.2.1.1.15Timeout (400..3000)read-writemandatory
atswitchBrStpPortTable
OBJECT-TYPE
A table that contains port-specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.207.8.10.9.2.15not-accessiblemandatory
atswitchBrStpPortEntry
OBJECT-TYPE
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
1.3.6.1.4.1.207.8.10.9.2.15.1not-accessiblemandatory
atswitchBrStpPortLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.2.15.1.1INTEGERread-onlymandatory
atswitchBrStpPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.207.8.10.9.2.15.1.2INTEGER (1..65535)read-onlymandatory
atswitchBrStpPortPriority
OBJECT-TYPE
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of atswitchBrStpPort.
1.3.6.1.4.1.207.8.10.9.2.15.1.3INTEGER (0..255)read-writemandatory
atswitchBrStpPortState
OBJECT-TYPE
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see atswitchBrStpPortEnable), this object will have a value of disabled(1).
1.3.6.1.4.1.207.8.10.9.2.15.1.4INTEGER {disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)}read-onlymandatory
atswitchBrStpPortEnable
OBJECT-TYPE
The enabled/disabled status of the port.
1.3.6.1.4.1.207.8.10.9.2.15.1.5INTEGER {enabled(1), disabled(2)}read-writemandatory
atswitchBrStpPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
1.3.6.1.4.1.207.8.10.9.2.15.1.6INTEGER (1..65535)read-writemandatory
atswitchBrStpPortDesignatedRoot
OBJECT-TYPE
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
1.3.6.1.4.1.207.8.10.9.2.15.1.7BridgeIdread-onlymandatory
atswitchBrStpPortDesignatedCost
OBJECT-TYPE
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.207.8.10.9.2.15.1.8INTEGERread-onlymandatory
atswitchBrStpPortDesignatedBridge
OBJECT-TYPE
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
1.3.6.1.4.1.207.8.10.9.2.15.1.9BridgeIdread-onlymandatory
atswitchBrStpPortDesignatedPort
OBJECT-TYPE
The Port Identifier of the port on the Designated Bridge for this port's segment.
1.3.6.1.4.1.207.8.10.9.2.15.1.10OCTET STRING (SIZE(2))read-onlymandatory
atswitchBrStpPortForwardTransitions
OBJECT-TYPE
The number of times this port has transitioned from the Learning state to the Forwarding state.
1.3.6.1.4.1.207.8.10.9.2.15.1.11Counterread-onlymandatory
atswitchBrTp
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.9.3
atswitchBrTpTable
OBJECT-TYPE
Table of transparent bridging information.
1.3.6.1.4.1.207.8.10.9.3.1not-accessiblemandatory
atswitchBrTpEntry
OBJECT-TYPE
An entry in the atswitchBrTpTable.
1.3.6.1.4.1.207.8.10.9.3.1.1not-accessiblemandatory
atswitchBrTpLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.3.1.1.1INTEGERread-onlymandatory
atswitchBrTpLearnedEntryDiscards
OBJECT-TYPE
The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
1.3.6.1.4.1.207.8.10.9.3.1.1.2Counterread-onlymandatory
atswitchBrTpAgingTime
OBJECT-TYPE
The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
1.3.6.1.4.1.207.8.10.9.3.1.1.3INTEGER (10..1000000)read-writemandatory
atswitchBrTpFdbTable
OBJECT-TYPE
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
1.3.6.1.4.1.207.8.10.9.3.3not-accessiblemandatory
atswitchBrTpFdbEntry
OBJECT-TYPE
Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
1.3.6.1.4.1.207.8.10.9.3.3.1not-accessiblemandatory
atswitchBrTpFdbLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.3.3.1.1INTEGERread-onlymandatory
atswitchBrTpFdbAddress
OBJECT-TYPE
A unicast MAC address for which the bridge has forwarding and/or filtering information.
1.3.6.1.4.1.207.8.10.9.3.3.1.2MacAddressread-onlymandatory
atswitchBrTpFdbPort
OBJECT-TYPE
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of atswitchBrTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address . Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of atswitchBrTpFdbStatus is not learned(3).
1.3.6.1.4.1.207.8.10.9.3.3.1.3INTEGERread-onlymandatory
atswitchBrTpFdbStatus
OBJECT-TYPE
The status of this entry. The meanings of the values are: inactive(1) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. active(2) : the value of the corresponding instance of atswitchBrTpFdbPort was active, and is being used. other(3) : none of the following. This would include the case where some other MIB object (not the corresponding instance of atswitchBrTpFdbPort ) is being used to determine if and how frames addressed to the value of the corresponding instance of atswitchBrTpFdbAddress are being forwarded.
1.3.6.1.4.1.207.8.10.9.3.3.1.4INTEGER {inactive(1), active(2), other(3)}read-onlymandatory
atswitchBrTpPortTable
OBJECT-TYPE
A table that contains information about every port that is associated with this transparent bridge.
1.3.6.1.4.1.207.8.10.9.3.4not-accessiblemandatory
atswitchBrTpPortEntry
OBJECT-TYPE
A list of information for each port of a transparent bridge.
1.3.6.1.4.1.207.8.10.9.3.4.1not-accessiblemandatory
atswitchBrTpPortLanId
OBJECT-TYPE
This object uniquely identifies the lan or Virtual lan.
1.3.6.1.4.1.207.8.10.9.3.4.1.1INTEGERread-onlymandatory
atswitchBrTpPort
OBJECT-TYPE
The port number of the port for which this entry contains Transparent bridging management information.
1.3.6.1.4.1.207.8.10.9.3.4.1.2INTEGER (1..65535)read-onlymandatory
atswitchBrTpPortMaxInfo
OBJECT-TYPE
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
1.3.6.1.4.1.207.8.10.9.3.4.1.3INTEGERread-onlymandatory
atswitchBrTpPortInFrames
OBJECT-TYPE
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.207.8.10.9.3.4.1.4Counterread-onlymandatory
atswitchBrTpPortOutFrames
OBJECT-TYPE
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.207.8.10.9.3.4.1.5Counterread-onlymandatory
atswitchBrTpPortInDiscards
OBJECT-TYPE
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process.
1.3.6.1.4.1.207.8.10.9.3.4.1.6Counterread-onlymandatory
atswitchStaticMACGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.10
atswitchStaticMACTable
OBJECT-TYPE
This tables lists Mac Addresses lexicographically from the Static table which binds MAC addresses to ports on the switch.
1.3.6.1.4.1.207.8.10.10.1not-accessiblemandatory
atswitchStaticMACEntry
OBJECT-TYPE
Entry in the atswitchStaticMACTable.
1.3.6.1.4.1.207.8.10.10.1.1not-accessiblemandatory
atswitchStaticMACAddress
OBJECT-TYPE
This object identifies the MAC Address associated with Static MAC Table.
1.3.6.1.4.1.207.8.10.10.1.1.1MacAddressread-onlymandatory
atswitchStaticMACPortNumbers
OBJECT-TYPE
This object identifies the Ports for which the above MAC address is associated Statically in Static MAC Table. This Object could take the port numbers as the Static Address added can be Multicast addresses. This Object is a DisplayString So, the input for example would be 1,5,6,8,9
1.3.6.1.4.1.207.8.10.10.1.1.2DisplayStringread-writemandatory
atswitchStaticMACVlan
OBJECT-TYPE
The Static MAC Address to be added can also be confined to a Vlan also. If the Port does not belong to that Vlan. the Port is forced to be moved to that Vlan.
1.3.6.1.4.1.207.8.10.10.1.1.3INTEGERread-writemandatory
atswitchPortMacAddrGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.12
atswitchPortMACTable
OBJECT-TYPE
A table that contains information about unicast entries seen on ports.
1.3.6.1.4.1.207.8.10.12.1not-accessiblemandatory
atswitchPortMACEntry
OBJECT-TYPE
Information about a specific unicast MAC address seen on ports.
1.3.6.1.4.1.207.8.10.12.1.1not-accessiblemandatory
atswitchPortMACAddress
OBJECT-TYPE
A unicast MAC address seen on this port.
1.3.6.1.4.1.207.8.10.12.1.1.1MacAddressread-onlymandatory
atswitchPortMACPort
OBJECT-TYPE
This object identifies the port on which the atswitchPortMACAddress was seen.
1.3.6.1.4.1.207.8.10.12.1.1.2INTEGERread-onlymandatory
atswitchDebugMallocLogGroup
OBJECT-IDENTITY
1.3.6.1.4.1.207.8.10.13
atswitchDebugMallocLogTable
OBJECT-TYPE
Dont care.
1.3.6.1.4.1.207.8.10.13.1not-accessibledeprecated
atswitchMallocLogEntry
OBJECT-TYPE
Entry in the atswitchDebugMallocLogEntry.
1.3.6.1.4.1.207.8.10.13.1.1not-accessibledeprecated
atswitchDebugMallocLogIndex
OBJECT-TYPE
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the address where malloc is done and no free is done. The size of this 6000.
1.3.6.1.4.1.207.8.10.13.1.1.1INTEGERread-onlydeprecated
atswitchDebugMallocLogCaller
OBJECT-TYPE
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the caller address who malloc'd . The size of this 6000.
1.3.6.1.4.1.207.8.10.13.1.1.2INTEGERread-onlydeprecated
atswitchDebugMallocLogAddress
OBJECT-TYPE
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the address where malloc is done and no free is done. The size of this 6000.
1.3.6.1.4.1.207.8.10.13.1.1.3INTEGERread-onlydeprecated

Notifications

NameOIDStatus
newRoot
NOTIFICATION-TYPE
The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election. Implementation of this trap is optional.
1.3.6.1.4.1.207.0.101
topologyChange
NOTIFICATION-TYPE
A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition. Implementation of this trap is optional.
1.3.6.1.4.1.207.0.102
intruderTrap
NOTIFICATION-TYPE
The intruderTrap trap indicates that there was a Intruder was detected on the port shown as ifIndex.
1.3.6.1.4.1.207.0.105