AT-UWC-WLAN-SWITCH-MIB

TEXTUAL-CONVENTION

Access category (AC) used for TSPEC. Only those ACs that support mandatory admission control are listed here.

TEXTUAL-CONVENTION

24-bit Organizationally Unique Identifier. Information on OUIs can be found in IEEE 802-2001 [802-2001] Clause 9.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Flag to enable/disable wireless controller functionality on the device. Disable will purge all status and statistics related to wireless functionality.

OBJECT-TYPE

This object indicates country of operation for WLAN. Supported country codes are: Australia - AU, Austria - AT, Austria - AT, Belgium - BE, Brazil - BR, Canada - CA, China - CN, Czech Republic - CZ, Denmark - DK, Finland - FI, France - FR, Germany - DE, Greece - GR, Hong Kong - HK, Hungary - HU, Iceland - IS, India - IN, Ireland - IE, Israel - IL, Italy - IT, Japan - JP, Liechtenstein - LI,Luxembourg - LU,Malaysia - MY, Mexico - MX, Netherlands - NL, New Zealand - NZ, Norway - NO, Poland - PL, Portugal - PT, Saudi Arabia - SA, Singapore - SG, Slovakia - SK, Slovenia - SI, South Africa - ZA, South Korea - KR, Spain - ES, Sweden - SE, Switzerland - CH, Taiwan - TW, Thailand - TH, United Arab Emirates - AE, United Kingdom - GB, United States - US.

OBJECT-TYPE

This object indicates which peer group this controller belongs to, there may be more than one group of peer controllers in the WLAN.

OBJECT-TYPE

This object indicates whether or not to verify newly discovered APs and look up their configuration against the local database or a RADIUS server.

OBJECT-TYPE

Flag to indicate if authentication is required for an AP to establish communication with the controller.

OBJECT-TYPE

Time in seconds to wait after a client disassociates from a managed AP before deleting the client association database entry.

OBJECT-TYPE

Time in hours to wait before deleting an entry obtained from an RF scan.A value of 0 in input range means that the entry never ages out.

OBJECT-TYPE

Time in hours to wait before deleting an entry in the AP association and authentication failure list. A value of 0 in input range means that the entry never ages out.

OBJECT-TYPE

Time in hours to wait before deleting an entry in Ad hoc client list.A value of 0 in input range means that the entry never ages out.

OBJECT-TYPE

Time in hours to wait before deleting an entry from the detected clients database.A value of 0 in input range means that the entry never ages out.

OBJECT-TYPE

This table contains configurable parameters for a specific AP. When an AP is discovered and the wsValidationMethod is local, its MAC address is verified in this table to determine if it should be managed by the controller.

OBJECT-TYPE

Each entry has parameters that can be configured locally or on a RADIUS server, for a specific AP on the WLAN. As this table is indexed by wsAPMacAddress, - to create an entry, specify the AP MAC address and set object wsAPConfigRowStatus to createAndGo(4) - to delete an entry, select the entry from the list and set object wsAPConfigRowStatus to destroy(6)

OBJECT-TYPE

MAC address of an AP.

OBJECT-TYPE

This object indicates description of an AP, often based on its location.

OBJECT-TYPE

This field indicates whether this AP is managed by the controller, by an administrator, or is a Rogue AP.

OBJECT-TYPE

If AP authentication is enabled, this indicates the password for an AP to authenticate to the controller. This must match the password configured on an AP. When passwod is configured this object will always return '*****'.

OBJECT-TYPE

If AP is managed by controller, this object indicates Id of configuration profile for this AP.

OBJECT-TYPE

This object indicates the fixed channel for the AP radio one. Zero indicates automatic channel assignment.

OBJECT-TYPE

This object indicates the fixed channel for the AP radio two. Zero indicates automatic channel assignment.

OBJECT-TYPE

This indicates the power setting of AP radio one. Zero indicates automatic power adjustment.

OBJECT-TYPE

This indicates the power setting of AP radio two. Zero indicates automatic power adjustment.

OBJECT-TYPE

This object indicates the expected channel for the AP in standalone mode. Zero indicates that any channel is allowed.

OBJECT-TYPE

This object indicates the expected security mode for the AP in standalone mode. Zero indicates that any security mode is allowed.

OBJECT-TYPE

This object indicates the expected SSID for the AP in standalone mode. A null string indicates that any SSID is allowed.

OBJECT-TYPE

This object indicates whether the AP is allowed to operate as a bridge. Configurable values are: any Either WDS or normal mode is allowed normal - AP is not allowed to operate in WDS mode bridge - AP is only allowed to operate in WDS mode

OBJECT-TYPE

This object indicates the expected wired network mode for the AP in standalone mode.

OBJECT-TYPE

This object is used to create or delete entries in the table. The supported values are: active(1) - indicates a valid entry createAndGo(4) - creates a new entry in the table destroy(6) - removes an existing entry from the table As this table is indexed by wsAPMacAddress, - to create an entry, specify the AP MAC address and set object value to createAndGo(4) - to delete an entry, select the entry from the list and set object value to destroy(6)

OBJECT-IDENTITY

OBJECT-TYPE

This object represents wireless controller IP address. When wireless mode is in disabled state, the value of controller IP address is zero.

OBJECT-TYPE

Indicates the current operating status of the wireless system.

OBJECT-TYPE

This object indicates the reason of operational status to be disabled. Values 5 and 6 are applicable only if routing functionality present.

OBJECT-TYPE

Total number of peer controllers detected on the network.

OBJECT-TYPE

Sum of all the WS managed APs, connection failed APs, and discovered APs in the database.

OBJECT-TYPE

Total number of WS managed APs currently authenticated to the controller.

OBJECT-TYPE

Total number of trusted AP's in the standalone mode.

OBJECT-TYPE

Number of APs that are connected to the controller, but are not completely configured.

OBJECT-TYPE

Number of APs that were previously authenticated and managed, but currently do not have connection with the controller.

OBJECT-TYPE

Total number of Rogue APs detected on the WLAN.

OBJECT-TYPE

Total number of Unknown APs detected on the WLAN.

OBJECT-TYPE

Maximum number of APs that can be managed by the wireless controller when it acts as Cluster Controller.

OBJECT-TYPE

Total number of clients present in the network.

OBJECT-TYPE

Total number of authenticated clients across all APs managed by the controller.

OBJECT-TYPE

Maximum number of clients that can associate with the wireless system.

OBJECT-TYPE

Total network utilization across all APs managed by this controller. This is based on global statistics.

OBJECT-TYPE

Regulatory domain for 2GHz frequency channels.

OBJECT-TYPE

Regulatory domain for 5GHz frequency channels.

OBJECT-TYPE

This action object is used to: - start - Start the config push into all the peer controllers in the peer group. - Read on this object will always return none.

OBJECT-TYPE

The global status for the configuration push operation to one or more peer controllers.

OBJECT-TYPE

The global status when wireless configuration is received from a peer controller.

OBJECT-TYPE

IP Address of the last controller from which this controller received any wireless configuration data.

OBJECT-TYPE

Indicates which portions of configuration were last received from a peer controller.

OBJECT-TYPE

The last time this controller received any configuration data from a peer controller.

OBJECT-TYPE

Indicates if the controller is currently the Cluster Controller of the peer group or not.

OBJECT-TYPE

This object represents Cluster Controller's IP address.

OBJECT-TYPE

Number of APs to which the wireless system is currently sending de-authentication messages to mitigate against rogue APs.

OBJECT-TYPE

Maximum number of APs for which the system can send de-authentication frames.

OBJECT-TYPE

This is a command that allows the administrator to clear out all rogue AP states in the RF Scan database

OBJECT-TYPE

Total number of detected clients across all APs managed by the controller.

OBJECT-TYPE

Maximum number of clients that can be maintained by the detected clients database.

OBJECT-TYPE

Maximum number of pre-authentication history entries that can be recorded for all the detected clients present in the detected client database.

OBJECT-TYPE

Total number of pre-authentication history entries accumulated for all the detected clients present in the detected client database.

OBJECT-TYPE

Maximum number of roam history entries that can be recorded for all the detected clients present in the detected client database.

OBJECT-TYPE

Total number of roam history entries accumulated for all the detected clients present in the detected client database.

OBJECT-TYPE

This action object is used to: - start - Start the certificate regeneration on the controller. - Read on this object will always return none.

OBJECT-TYPE

Status of regenerate X.509 certificates.

OBJECT-TYPE

Status of the mutual authentication enable/disable command. When status is Complete With Errors then the administrator may need to provision some controllers or APs separately.

OBJECT-TYPE

Total number of APs present in the AP Provisioning database.

OBJECT-TYPE

Maximum number of APs that can be maintained in the AP Provisioning database.

OBJECT-IDENTITY

OBJECT-TYPE

Total bytes transmitted across all APs managed by this controller.

OBJECT-TYPE

Total bytes received across all APs managed by by this controller.

OBJECT-TYPE

Total packets transmitted across all APs managed by this controller.

OBJECT-TYPE

Total packets received across all APs managed by this controller.

OBJECT-TYPE

When we set this object to enable, all statistics maintained by controller will be cleared. Read on this object will always return disable.

OBJECT-TYPE

This object indicates the current status of controller statistics reset request. Default value is not started.

OBJECT-TYPE

Total bytes dropped in the transmit direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the receive direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the transmit direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the receive direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total number of packets transmitted by all APs using distributed tunnels.

OBJECT-TYPE

Number of clients in all APs currently in roaming state using distributed tunnels.

OBJECT-TYPE

Number of client tunnel setups denied for all APs.

OBJECT-IDENTITY

OBJECT-TYPE

Flag to enable/disable the functionality to send global configuration parameters to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send discovery configuration parameters to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send valid AP Database to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send Channel and Power configuration to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send all AP profiles and networks to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send configured known client entries to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send all Captive Portal configuration to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send RADIUS Client configuration parameters to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send all QoS ACL configuration to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send all QoS DiffServ configuration to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send configured wds groups to a peer controller on a configuration push.

OBJECT-TYPE

Flag to enable/disable the functionality to send configured device location parameters to a peer controller on a configuration push.

OBJECT-TYPE

Preference level of the controller to become the Cluster Controller of the Peer Group.A priority of 0 means that the controller can not become cluster controller.

OBJECT-TYPE

Flag to globally enable/disable AP quality-of-service operation for wireless clients.

OBJECT-TYPE

Flag to enable/disable AP auto upgrade mode. This object is configurable only if the wireless controller supports both 'Integrated' and 'Independent' AP image download modes. If the controller supports only 'Integrated' mode, the default is Enable.

OBJECT-TYPE

Time of inactivity in seconds to wait before terminating a tunnel client.

OBJECT-TYPE

Time in seconds to wait before terminating a tunnel client.

OBJECT-TYPE

Maximum number of multicast replications that can be performed by the AP.

OBJECT-TYPE

Maximum number of clients that can use tunneled through a Home AP.

OBJECT-TYPE

This object indicates whether MAC addresses in the Known Client database are granted or denied access if they are in the list, but dont have a specific action.

OBJECT-TYPE

This table contains entries of the known clients.

OBJECT-TYPE

The entry contains parameters of a known client.

OBJECT-TYPE

MAC address of the known client.

OBJECT-TYPE

This object indicates whether to grant, deny, or use global action for client authentication.

OBJECT-TYPE

Descriptive name of the known client.

OBJECT-TYPE

This object is used to create or delete entries in this table.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Report the AP as rogue in the RF Scan if the local database indicates that the AP is rogue. Can not be disabled.

OBJECT-TYPE

Enable rogue reporting for unknown AP's detected with a managed SSID.

OBJECT-TYPE

Enable rogue reporting for fake managed AP's detected with a managed SSID.

OBJECT-TYPE

Enable rogue reporting of all APs detected with no SSID.

OBJECT-TYPE

Enable rogue reporting of fake managed AP's detected with an invalid channel.

OBJECT-TYPE

Enable rogue reporting of AP's detected with managed SSID's and an invalid security configuration.

OBJECT-TYPE

Enable rogue reporting of managed AP's with an invalid SSID.

OBJECT-TYPE

Enable rogue reporting of AP's operating on an illegal channel.

OBJECT-TYPE

Enable rogue reporting of standalone AP's operating with an unexpected configuration.

OBJECT-TYPE

Enable rogue reporting of unexpected WDS devices.

OBJECT-TYPE

Enable rogue reporting of unmanaged AP's on a wired network.

OBJECT-TYPE

Minimum number of seconds that the AP waits before starting a new wired network detection cycle. A value of 0 disables wired network detection.

OBJECT-TYPE

The interval in seconds between transmissions of the trap telling the administrator that Rogues are present in the RF Scan database. A configured value of 0 disables the trap from being sent. .

OBJECT-TYPE

Enable the AP de-authentication attack.

OBJECT-IDENTITY

OBJECT-TYPE

The interval in seconds between transmissions of the trap telling the administrator that Rogues are present in the Rogue Clients are present in the Detected Clients Database. A configured value of 0 disables the trap from being sent.

OBJECT-TYPE

Report the client as rogue if it fails the Known Client Database Test.

OBJECT-TYPE

Report the client as rogue if it exceeds configured rate for transmitting 802.11 authentication requests.

OBJECT-TYPE

Report the client as rogue if it exceeds configured rate for transmitting probe requests.

OBJECT-TYPE

Report the client as rogue if it exceeds configured rate for transmitting 802.11 deauthentication requests.

OBJECT-TYPE

Report the client as rogue if it exceeds maximum number of failing authentications.

OBJECT-TYPE

Report the client as rogue if it is authenticated with an unknown AP.

OBJECT-TYPE

Transmission of de-authentication messages to known clients associated with unknown APs. The Known Client test must also be enabled in order for the mitigation to take place.

OBJECT-TYPE

Number of seconds for counting the de-authentication messages.

OBJECT-TYPE

If controller receives more than specified de-auth messages during the threshold interval the test triggers the client to be reported as rogue.

OBJECT-TYPE

Number of seconds for counting the authentication messages.

OBJECT-TYPE

If controller receives more than specified auth messages during the threshold interval the test triggers the client to be reported as rogue.

OBJECT-TYPE

Number of seconds for counting the probe messages.

OBJECT-TYPE

If controller receives more than specified probe messages during the threshold interval the test triggers the client to be reported as rogue.

OBJECT-TYPE

The number of 802.1X authentication failures that triggers the client to be reported as rogue.

OBJECT-TYPE

The location of Known Client Database. If the value is local then Known Client Database is located in the local controller. Otherwise the database is located in the RADIUS Server.

OBJECT-TYPE

Name of the RADIUS server used for Known Client database This is used when knownClientDatabaseLocation is set to 'radius'.

OBJECT-TYPE

Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.

OBJECT-TYPE

Report the client as rogue if it's OUI is not present in the OUI Database.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Name of the RADIUS server used for AP authentications as well as client authentications when a network-level RADIUS server is not defined.

OBJECT-TYPE

Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.

OBJECT-TYPE

Name of the RADIUS server used for reporting wireless client associations and disassociations when a network-level RADIUS accounting server is not defined.

OBJECT-TYPE

Indicates whether the specified named RADIUS Accounting server is configured in the RADIUS Client configuration.

OBJECT-TYPE

Flag to indicate whether or not RADIUS accounting is enabled for wireless clients.

OBJECT-TYPE

This table contain access point and client status parameters of peer controllers of wireless controller.

OBJECT-TYPE

Each entry describes the access point and client status parameters of each peer of wireless controller.

OBJECT-TYPE

This object represents wireless controller IP address. When wireless mode is in disabled state, return entry will be none.

OBJECT-TYPE

Preference level of the controller to become the Cluster Controller of the Peer Group.

OBJECT-TYPE

The AP image download mode supported by the wireless controller. The displayed mode can be one of the following: Integrated - The controller supports Integrated mode. In this mode, the AP code is located on the controller, and the controller automatically updates the code on APs it manages. Independent - The controller supports Independent mode. In this mode, the AP code is on a TFTP server, and the download is triggered from the cluster controller. Integrated, Independent - The controller supports both modes. Note that this field displays the mode only if wireless controllers that support Independent and Integrated AP Image Download modes co-exist in the network.

OBJECT-TYPE

Sum of all the WS managed APs, connection failed APs, and discovered APs in the database of specified controller.

OBJECT-TYPE

Total number of WS managed APs currently authenticated, configured and have an active connection with the specifed controller.

OBJECT-TYPE

Number of APs that are connected to the specified controller, but have not been completely configured.

OBJECT-TYPE

Number of APs that were previously authenticated and managed, but currently do not have connection with the specified controller.

OBJECT-TYPE

Maximum number of APs that the specified controller can manage.

OBJECT-TYPE

Total number of clients in the database that include clients with an associated, authenticated and disassociated status.

OBJECT-TYPE

Total number of authenticated clients across all APs managed by the specified controller.

OBJECT-TYPE

Total network utilization across all APs managed by the specifed controller.

OBJECT-TYPE

Number of clients that are currently sending and receiving packets via distributed tunnels.

OBJECT-TYPE

This table contain WLAN statistics for every controller in the peer group. Only Cluster Controller can hold the entries for peer controllers. The controller which is not a Cluster Controller only keep statistics local to it.

OBJECT-TYPE

Each entry describe WLAN statistics of specified controller in the wireless system.

OBJECT-TYPE

Total bytes transmitted across all APs managed by the specified controller.

OBJECT-TYPE

Total bytes received across all APs managed by the specified controller.

OBJECT-TYPE

Total packets transmitted across all APs managed by the specified controller.

OBJECT-TYPE

Total packets received across all APs managed by the specified controller.

OBJECT-TYPE

Total bytes dropped in the transmit direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the receive direction across all APs managed the specified controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the transmit direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the receive direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Flag indicating whether the Wireless feature should automatically assign an IP address from one of the active interfaces or whether the IP address is manually assigned.

OBJECT-TYPE

Statically assigned IPv4 address for the Wireless feature. If Auto IP Assignment is true then this setting is ignored.

OBJECT-IDENTITY

OBJECT-TYPE

Specifies the time period at which wireless clients detected as using admission-controlled resources without proper TSPEC authorization are reported via the system logging and SNMP trap mechanisms. If a violating client disassociates before the next report interval, it is reported upon disassociation. This object is specified in seconds, with a default value of 300 (5 minutes). Setting this object value to 0 disables TSPEC violation reporting.

OBJECT-TYPE

Flag to enable/disable mutual authentication of the Wireless controllers and Access Points in the network.

OBJECT-TYPE

Flag to enable/disable reprovisioning of APs when in unmanaged mode.

OBJECT-TYPE

Time in hours to wait without hearing any updates for the APs before removing them from the provisioning database.A value of 0 in input range means that the entry never ages out.

OBJECT-TYPE

Flag to enable/disable controller provisioning.

OBJECT-TYPE

Base IP port.

OBJECT-TYPE

Measurement system in english/metric.

OBJECT-TYPE

Flag to enable/disable RF Scan location Mode.

OBJECT-TYPE

Number of seconds between iterations of triangulation table device location protocol.

OBJECT-IDENTITY

OBJECT-TYPE

Flag to enable/disable IP based discovery of APs and peer controllers.

OBJECT-TYPE

Flag to enable/disable L2 discovery of APs and peer controllers.

OBJECT-TYPE

This table contains IP addresses to poll on the network.

OBJECT-TYPE

An IP address list that can be configured globally on the wireless controller to define which IP addresses to poll in order to discover new APs and peer controllers. This list is used when discovery via IP Polling is enabled.

OBJECT-TYPE

IP address of an AP or controller to poll.

OBJECT-TYPE

Indicates whether or not the controller reached this IP address.

OBJECT-TYPE

This object is used to create and delete entries in the table.

OBJECT-TYPE

This table contains the list of VLANs on which to send L2 discovery multicast packets.

OBJECT-TYPE

A list of VLANs on which to send L2 discovery multicast frames when L2 broadcast discovery mode is enabled. The entries in this table are limited to sixteen. By default there will be one entry in this table with wsL2DiscoveryVlanId equal to one. This entry can neither be created nor deleted.

OBJECT-TYPE

VLAN Id on which controller will send L2 discovery multicast frames.

OBJECT-TYPE

This variable is used to create and delete entries in the table.

OBJECT-TYPE

Maximum number of IP discovery entries allowed to be configured.

OBJECT-TYPE

Total number of entries configured IP discovery entries.

OBJECT-TYPE

Total number of polled entries in the IP discovery list.

OBJECT-TYPE

Total number of not-polled entries in the IP discovery list.

OBJECT-TYPE

Total number of discovered entries in the IP discovery list.

OBJECT-TYPE

Total number of discovered-failed entries in the IP discovery list.

OBJECT-IDENTITY

OBJECT-TYPE

The following parameters can be configured within an AP configuration profile. A profile is used to replicate a single AP configuration across multiple managed APs. Modification or deletion is not allowed if the profile is assigned to one or more managed APs except wsCopyAPProfileToProfileId.

OBJECT-TYPE

Each entry has parameters that can be configured within an AP configuration profile. A profile is used to replicate a single AP configuration across multiple managed APs, and is indexed by an integer Id.

OBJECT-TYPE

Unique AP Profile Id for each entry.

OBJECT-TYPE

AP configuration profile name.

OBJECT-TYPE

Indicates current state of AP Profile.

OBJECT-TYPE

This object is used to create or delete entries in the table.

OBJECT-TYPE

This object copies the AP profile configuration to the specified valid AP Profile Id. If specified Profile Id is already assigned to one or more managed APs, the operation is not allowed. Read on this object will always return zero.

OBJECT-TYPE

This object is used to apply the AP profile configuration. Read on this object will always return none.

OBJECT-TYPE

AP Hardware type ID associated with each entry.

OBJECT-TYPE

VLAN ID that is used to send packets on the wire that enable the system to discover rogue APs attached to the wired network.

OBJECT-TYPE

Flag to enable/disable Disconnected AP Data Forwarding Mode.

OBJECT-TYPE

Flag to enable/disable Disconnected AP Management Mode.

OBJECT-TYPE

Flag to enable/disable AE Protocol Support Mode.

OBJECT-TYPE

This table contains parameters that can be configured with in an AP Profile per radio interface.

OBJECT-TYPE

Each entry in this table represents parameters that can be configured with in an AP profile per radio interface. Two entries in this table will get created automatically for each AP profile being created in wsAPProfileTable. Whenever AP profile entry is deleted, corresponding radio profile entries will get deleted automatically.

OBJECT-TYPE

AP physical radio interface number.

OBJECT-TYPE

Flag to indicate whether the radio is operational.

OBJECT-TYPE

Indicates which physical layer technology to use on radio. Default value for radio 1 is 'ieee802dot11bgn' and default value for radio 2 is 'ieee802dot11an'.

OBJECT-TYPE

When Sentry mode is disabled this flag controls whether the radio moves away from the operating channel while doing scans. When this mode is disabled the radio scans only on the operating channel. When sentry mode is enabled on the radio this parameter is ignored.

OBJECT-TYPE

If scan mode is enable, indicates how often the radio leaves its operational channel.

OBJECT-TYPE

When Sentry mode is enabled the radio doesn't do any data forwarding, but only periodically scan channels for rogues. The length of time spent on each channels controlled by the 'scan duration' time.

OBJECT-TYPE

If scanning is enabled, this object indicates on which frequencies to scan.

OBJECT-TYPE

Indicates how long the radio can scan before returning to its operational channel. The default value is 10ms.

OBJECT-TYPE

This object enables/disables rate limit for broadcast and multicast traffic transmitted across the network.

OBJECT-TYPE

Allowed rate limit for broadcast/multicast traffic transmitted across the network. Broadcast/multicast traffic below this limit is transmitted normally.

OBJECT-TYPE

Broadcast/multicast traffic can occur in bursts up to this value before all traffic is considered to exceed the limit.

OBJECT-TYPE

Interval at which the AP transmit beacon frames.

OBJECT-TYPE

Indicates the number of beacons between Delivery Traffic Indication MAP(DTIM). DTIM indicates buffered broadcast/multicast traffic on an AP.

OBJECT-TYPE

This object limits the size of packets transmitted over the network. Only even values are allowed in the defined range.

OBJECT-TYPE

This object indicates the number of octets in an MAC Protocol Data Unit(MPDU), below which an request to send(RTS)/clear to send(CTS) handshake shall not be performed.

OBJECT-TYPE

This object indicates the maximum number of transmission attempts on frame sizes less than or equal to the RTS threshold. Set action for this object will be supported in next release.

OBJECT-TYPE

This object indicates the maximum number of transmission attempts on frame sizes greater than the RTS threshold. Set action for this object will be supported in next release.

OBJECT-TYPE

This object indicates the elapsed time after the initial transmission of MAC Service Data Unit(MSDU), after which further attempts to transmit the MSDU shall be terminated. Set action for this object will be supported in next release.

OBJECT-TYPE

This object indicates the elapsed time after the initial reception of a fragmented MAC Management Protocol Data Unit(MMPDU) or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. Set action for this object will be supported in next release.

OBJECT-TYPE

Maximum number of client stations that can simultaneously get associated on this interface.

OBJECT-TYPE

Flag to indicate power is automatically adjusted by the controller.

OBJECT-TYPE

If auto power mode is disabled, this object indicates a fixed power setting for the radio.

OBJECT-TYPE

Flag to enable/disable Wi-Fi MultiMedia Mode. When enabled, QOS settings affect both downstream traffic to the sation and upstream traffic to the AP. When disabled, QOS only applies to downstream traffic.

OBJECT-TYPE

Flag to indicate that AP will load balance users on this radio.

OBJECT-TYPE

If load balancing is enabled, percentage of network utilization allowed on the radio before clients are denied. This value is displayed in percentage.

OBJECT-TYPE

Flag to indicate whether initial AP radio channel assignment can be automatically adjusted by controller due to changes in radio performance.

OBJECT-TYPE

Flag to indicate whether Station Isolation is enabled on the Radio.

OBJECT-TYPE

Bandwidth used in the channel.

OBJECT-TYPE

Specify relative location of Primary Channel in the 40 MHz channel.

OBJECT-TYPE

Turn on/off Protection mechanisms.

OBJECT-TYPE

Dead time, in nanoseconds, between OFDM symbols which prevents Inter-Symbol and Inter-Carrier Interference (ISI, ICI). The short guard interval, when enabled, is 400ns and the standard guard interval, when disabled, is 800ns.

OBJECT-TYPE

The Space Time Block Code (STBC) Mode enables the AP to send the same data stream on multiple antennas at the same time. This is different from MIMO where the data stream is divided between two antennas.

OBJECT-TYPE

Indicates the data rate AP will send multicast data to its client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. 0 represents automatic rate selection. For Example : Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.

OBJECT-TYPE

Automatic Power Save Delivery Mode.

OBJECT-TYPE

Don't send acknowledgement to correctly received frames.

OBJECT-TYPE

Flag to enable/disable Radio Resource Management (RRM) as defined in the IEEE 802.11k specification. RRM allows wireless clients to request adjustments and report conditions regarding channel load and neighbor detection.

OBJECT-TYPE

This object indicates the QOS template choice in effect for the profile and radio.

OBJECT-TYPE

Minimum Transmit Power that can be set by APA on the radio. Default Value is 20% for 2.4Ghz Radio and 100% for 5Ghz radio.

OBJECT-TYPE

This table represents the supported data rates by AP Profile.

OBJECT-TYPE

Each entry in this table represents supported data rate.

OBJECT-TYPE

Indicates the data rate, AP will actually support in setting up communications with client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.

OBJECT-TYPE

Displays supported data rate by an AP Profile. Supported rates by an AP Profile depends on physical mode of the radio.

OBJECT-TYPE

This table represents the basic data rates advertised by an AP Profile.Stations connecting to this AP must support this set of data rates.

OBJECT-TYPE

Each entry in this table represents basic data rate.

OBJECT-TYPE

Indicates the basic data rate, AP will actually advertise to its client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. For Example : Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.

OBJECT-TYPE

Displays basic data rate advertised by an AP Profile. Basic rate depends on physical mode of the radio.

OBJECT-TYPE

This table is about VAP profile configuration. When AP profile entry is created, corresponding eight VAP entries will get created for each radio. When AP Profile entry is get deleted, corresponding VAP entries will be deleted automatically.

OBJECT-TYPE

Each entry in this table represents VAP profile.

OBJECT-TYPE

Index of the VAP with respect to the radio interface.

OBJECT-TYPE

Flag to enable/disable VAP. VAP0 can not be disabled. In order to disable VAP0, radio must be turned off.

OBJECT-TYPE

Network configuration assigned to the VAP. By default, VAP 0 to 7 are assigned to Network Ids 1 to 8 in order.

OBJECT-TYPE

This table displays QOS configuration. Enhanced Distributed Channel Access(EDCA) parameters of an AP affect downstream traffic from AP to the client station. Station EDCA parameters affect upstream traffic from the client station to an AP. Creation of AP Profile creates corresponding four qos profiles with default values for each radio. Deletion of AP Profile deletes the corresponding QOS entries in this table.

OBJECT-TYPE

Each entry in this table represents QOS profile.

OBJECT-TYPE

This object indicates QOS Queue Id.

OBJECT-TYPE

Specifies the wait time for data frames. The default values for each QOS Id is mentioned below: voice(0) - 1 msec video(1) - 1 msec besteffort(2) - 3 msec background(3) - 7 msec

OBJECT-TYPE

Specifies the upper limit of a range from which the initial random backoff wait time is determined. The default values for each QOS Id is mentioned below: voice(0) - 3 msec video(1) - 7 msec besteffort(2) - 15 msec background(3) - 15 msec

OBJECT-TYPE

Specifies the upper limit for the doubling of the random backoff value, doubling continues until either the data frame is sent or this value is reached. The default values for each QOS Id is mentioned below: voice(0) - 7 msec video(1) - 15 msec besteffort(2) - 63 msec background(3) - 1023 msec

OBJECT-TYPE

Specifies the maximum burst length allowed for packet bursts on the wireless network. The default values for each QOS Id is mentioned below: voice(0) - 1500 micro sec video(1) - 3000 micro sec besteffort(2) - 0 micro sec background(3) - 0 micro sec

OBJECT-TYPE

Specifies the wait time for data frames. The default values for each QOS Id is mentioned below: voice(0) - 2 msec video(1) - 2 msec besteffort(2) - 3 msec background(3) - 7 msec

OBJECT-TYPE

Specifies the upper limit of a range from which the initial random backoff wait time is determined for station. The default values for each QOS Id is mentioned below: voice(0) - 3 msec video(1) - 7 msec besteffort(2) - 15 msec background(3) - 15 msec

OBJECT-TYPE

Specifies the upper limit for the doubling of the random backoff value, doubling continues until either the data frame is sent or this value is reached. The default values for each QOS Id is mentioned below: voice(0) - 7 msec video(1) - 15 msec besteffort(2) - 63 msec background(3) - 1023 msec

OBJECT-TYPE

Specifies an interval of the time when a Wireless Multimedia Extensions(WME) client station has the right to initiate transmissions on to the wireless medium. The default values for each QOS Id is mentioned below: voice(0) - 47 msec video(1) - 94 msec besteffort(2) - 0 msec background(3) - 0 msec

OBJECT-TYPE

The following parameters can be configured for each network. A network may be assigned to one or more VAPs within an AP configuration profile. The first eight networks are created with default values, and cannot be deleted.

OBJECT-TYPE

Each entry in this table is associated with a unique network Id.

OBJECT-TYPE

Network Id used to uniquely identify the network.

OBJECT-TYPE

Add Network ID to the network configuration table. The first 16 network configurations are created by default, they are applied to VAP-0 through VAP-15 in order on each radio when a new AP configuration profile is created (one default network configuration exists per VAP ID).

OBJECT-TYPE

This object indicates Service Set ID specific to this Network. The first network is configured with a default SSID 'Guest Network', the rest of the networks have default SSIDs assigned based on the Network Id.

OBJECT-TYPE

Default VLAN Id assigned to the Network. The default VLAN is used if RADIUS based authentication is not configured for the network or the RADIUS server does not return a VLAN for a specific client.

OBJECT-TYPE

Flag to enable/disable inclusion of SSID in AP beacons.

OBJECT-TYPE

If client broadcasts probe requests to all available SSIDs this option controls whether or not the system will respond to the probe request. The 'disable' mode means that the system responds.

OBJECT-TYPE

This object indicates mode to disable, or enable and specify lookup method for authentication via client MAC address.

OBJECT-TYPE

Flag to enable/disable RADIUS accounting authentication for users on this network.

OBJECT-TYPE

Specifies authentication and encryption mode on this network.

OBJECT-TYPE

If Wi-Fi Protected Access(WPA) encryption mode is enabled, this object indicates the versions of WPA allowed by clients on this network.

OBJECT-TYPE

If WPA encryption mode is enabled, this object indicates which encryption solutions to use for WPA clients.

OBJECT-TYPE

If WPA-SharedKey security mode is enabled, this object specifies the type of the WPA key configured. Only ascii key type is supported for this release.

OBJECT-TYPE

If WPA-SharedKey security mode is enabled, this object specifies the pre-shared secret for WPA clients. For ASCII - 8-63 characters.

OBJECT-TYPE

If WPA2 encryption is enabled, flag to enable/disable pre-authentication support for roaming WPA2 clients.

OBJECT-TYPE

If WPA2 pre-authentication is enabled, this object specifies a limit on the number of APs within the peer group to which one client is allowed to be pre-authenticate.

OBJECT-TYPE

Length of time in minutes a PMK will be cached by an AP after the client using this PMK has roamed away from this AP. Length of time a PMK will be cached by an AP after the PMK has been received from the WS. After this time has expired, the AP deletes the PMK entry from the security database.

OBJECT-TYPE

Indicates security configuration for static WEP.

OBJECT-TYPE

If wsNetSecurityMode is wepSharedKey, this object indicates which Wired Equivalent Privacy(WEP) algorithm network will use for encryption.

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, this object specifies the type WEP key configured.

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, this object specifies number of bits for the WEP key.

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters

OBJECT-TYPE

If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters

OBJECT-TYPE

This is an action object. Setting this object to enable will set Network Id configuration to default configuration. Read on this object will always return disable.

OBJECT-TYPE

Specifies the redirect mode on this network.

OBJECT-TYPE

This object indicates HTTP Redirect URL on the Network Id.

OBJECT-TYPE

A unique value to identify the wireless network interface.

OBJECT-TYPE

The name of the RADIUS server used for client authentications.

OBJECT-TYPE

Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.

OBJECT-TYPE

The name of the RADIUS server used for reporting wireless client associations and disassociations.

OBJECT-TYPE

Indicates whether the specified named RADIUS Accounting server is configured in the RADIUS Client configuration.

OBJECT-TYPE

This flag controls whether the VAP uses the network RADIUS configuration or global RADIUS configuration. When enabled, network RADIUS configuration shall be used.

OBJECT-TYPE

Flag to enable/disable Distributed Tunneling for this Network.

OBJECT-TYPE

The 802.1x broadcastkey refresh rate command specifies the interval after which the broadcast keys are changed.

OBJECT-TYPE

The 802.1x SessionKey refresh rate command specifies the interval after which the Unicast session keys are changed. This is applicable only dynamic WEP and WPA Enterprise modes.Valid values are 0 and from 30-86400.

OBJECT-TYPE

Flag to enable/disable Wireless ARP Suppression for this Network.

OBJECT-TYPE

Configure band steering on this VAP. To have band steering operationally enabled, the following conditions should be met: 1. SSIDs on both VAPs should match. 2. One radio should be in the 2.4-GHz band, and the other should be in the 5-GHz band.

OBJECT-TYPE

The following parameters can be configured for each network. This table extends the wsNetworkTable definition.

OBJECT-TYPE

Each entry in this table is associated with a unique network ID, and defines its default client QoS parameters for a managed AP. These parameters are used for any wireless client on the designated network that does not have its own comparable parameter(s) defined via RADIUS when using 802.1X authentication.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client for this network, thus controlling the maximum receive rate from the AP for a wireless client. This parameter is specified in bits-per-second (bps). This object may be set to any value in the range 0-4294967295. Any configured non-zero value is rounded down to the nearest 64000 bps by the AP, but no lower than 64000. Setting this object value to 0 disables bandwidth limiting in this direction.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP for this network, thus controlling the maximum send rate to the AP for a wireless client. This parameter is specified in bits-per-second (bps). This object may be set to any value in the range 0-4294967295. Any configured non-zero value is rounded down to the nearest 64000 bps by the AP, but no lower than 64000. Setting this object value to 0 disables bandwidth limiting in this direction.

OBJECT-TYPE

Access list type used for the wireless down (outbound) direction from AP to client for this network. Setting this object usually requires that the wsNetworkClientQosAccessControlDownName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information).

OBJECT-TYPE

Name of the access list to use in accordance with the wsNetworkClientQosAccessControlDownType as follows: none(1) - This object is not used and must not be set. ip(2) - This specifies an IP access list number in the range 1-199, entered as a character string rather than an integer, or an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IP access list, as defined by the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are specified here using a character string notation instead of an integer value. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosAccessControlDownType to none(0), this object must not be set. 2. When setting wsNetworkClientQosAccessControlDownType to any value other than none(0), both the wsNetworkClientQosAccessControlDownType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosAccessControlDownType value, provided the type value is anything other than none(0).

OBJECT-TYPE

Access list type used for the wireless up (inbound) direction from client to AP for this network. Setting this object usually requires that the wsNetworkClientQosAccessControlUpName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information).

OBJECT-TYPE

Name of the access list to use in accordance with the wsNetworkClientQosAccessControlUpType as follows: none(1) - This object is not used and must not be set. ip(2) - This specifies an IP access list number in the range 1-199, entered as a character string rather than an integer, or an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IP access list, as defined by the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are specified here using a character string notation instead of an integer value. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosAccessControlUpType to none(0), this object must not be set. 2. When setting wsNetworkClientQosAccessControlUpType to any value other than none(0), both the wsNetworkClientQosAccessControlUpType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosAccessControlUpType value, provided the type value is anything other than none(0).

OBJECT-TYPE

DiffServ policy type used for the wireless down (outbound) direction from AP to client for this network. Setting this object usually requires that the wsNetworkClientQosDiffservPolicyDownName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information). Only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-TYPE

Name of the DiffServ policy to use in accordance with the wsNetworkClientQosDiffservPolicyDownType as follows: none(1) - This object is not used and must not be set. in(2) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosDiffservPolicyDownType to none(0), this object must not be set. 2. When setting wsNetworkClientQosDiffservPolicyDownType to any value other than none(0), both the wsNetworkClientQosDiffservPolicyDownType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosDiffservPolicyDownType value, provided the type value is anything other than none(0).

OBJECT-TYPE

DiffServ policy type used for the wireless up (inbound) direction from client to AP for this network. Setting this object usually requires that the wsNetworkClientQosDiffservPolicyUpName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information). Only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-TYPE

Name of the DiffServ policy to use in accordance with the wsNetworkClientQosDiffservPolicyUpType as follows: none(1) - This object is not used and must not be set. in(2) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosDiffservPolicyUpType to none(0), this object must not be set. 2. When setting wsNetworkClientQosDiffservPolicyUpType to any value other than none(0), both the wsNetworkClientQosDiffservPolicyUpType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosDiffservPolicyUpType value, provided the type value is anything other than none(0).

OBJECT-TYPE

Flag to enable/disable AP quality-of-service for wireless clients on this network.

OBJECT-TYPE

This table represents the supported channels by AP Profile.

OBJECT-TYPE

Each entry in this table represents a supported channel.

OBJECT-TYPE

Indicates a channel currently supported by the radio for use with client connections. The set of supported channel numbers is determined by country code, radio mode, and in the case of modes that are compatible with 802.11n, primary channel selection and channel bandwidth settings.

OBJECT-TYPE

This table represents the channels of an AP profile that are eligible for automatic channel selection.

OBJECT-TYPE

Each entry in this table represents an eligible channel.

OBJECT-TYPE

Indicates a channel currently eligible for automatic channel selection by the radio for use with client connections. The set of eligible channel numbers is a subset of the channels supported by the radio in its current configuration of country, mode, and in the case of modes that are compatible with 802.11n, primary channel selection and channel bandwidth settings. For 80Mhz 4 channels form a set and setting one channel would unset all the remaining channels in the set. Deleting one channel would unset all the channels in the set.

OBJECT-TYPE

The eligible channel status. Supported values: active(1) - valid instance createAndGo(4) - creates a new instance destroy(6) - removes an instance

OBJECT-TYPE

This table contains TSPEC parameters that can be configured within an AP Profile per radio interface.

OBJECT-TYPE

Each entry in this table represents TSPEC parameters that can be configured per radio interface within an AP profile. These entries augment the wsAPProfileRadioEntry definition for TSPEC configuration.

OBJECT-TYPE

The overall TSPEC operational mode for this radio. This object must be set to enable(1) for any of the other TSPEC ACM configuration parameters defined in this table row to have an effect. The default value for this object is disable(2).

OBJECT-TYPE

Regulates mandatory admission control for the voice access category (AC). When set to enable(1), the voice AC may only be used by WMM-compliant client stations that have successfully established a TSPEC for this AC. Note that setting the wsAPRadioTspecLegacyWmmQueueMapMode object to enable(1) overrides the exclusive use of the voice AC by allowing legacy (i.e. non-WMM-compliant) client stations to use it as well.

OBJECT-TYPE

Regulates mandatory admission control for the video access category (AC). When set to enable(1), the video AC may only be used by WMM-compliant client stations that have successfully established a TSPEC for this AC. Note that setting the wsAPRadioTspecLegacyWmmQueueMapMode object to enable(1) overrides the exclusive use of the video AC by allowing legacy (i.e. non-WMM-compliant) client stations to use it as well.

OBJECT-TYPE

Defines the maximum amount of wireless bandwidth utilization to admit for the voice access category. TSPEC requests that would cause this limit to be exceeded are rejected. Note that this value establishes an upper limit for wireless bandwidth to be admitted for this access category but does not guarantee that this limit can be reached. Setting this object value to 0 and the wsAPRadioTspecVoiceAcmMode object to enable(1) causes all TSPEC requests to be rejected by the AP for the voice access category. The sum of this value and the wsAPRadioTspecVideoAcmLimit object value is not allowed to exceed 70. This value is treated as a percentage.

OBJECT-TYPE

Defines the maximum amount of wireless bandwidth utilization to admit for the video access category. TSPEC requests that would cause this limit to be exceeded are rejected. Note that this value establishes an upper limit for wireless bandwidth to be admitted for this access category but does not guarantee that this limit can be reached. Setting this object value to 0 and the wsAPRadioTspecVideoAcmMode object to enable(1) causes all TSPEC requests to be rejected by the AP for the video access category. The sum of this value and the wsAPRadioTspecVoiceAcmLimit object value is not allowed to exceed 70. This value is treated as a percentage.

OBJECT-TYPE

Defines the portion of the wsAPRadioTspecVoiceAcmLimit and wsAPRadioTspecVideoAcmLimit object values to hold in reserve for roaming clients only. If this value exceeds the current value in either of those two objects, respectively, then their entire ACM limit is used exclusively for roaming clients. Setting this object value to 0 causes none of the voice or video ACM limit values to be reserved for roaming clients - they compete equally with non-roaming clients for wireless network bandwidth. This value is treated as a percentage.

OBJECT-TYPE

Specifies the amount of time that an active traffic stream (TS) in the downlink direction may be idle, from the perspective of the AP, before it is deleted by the AP. For a bidirectional TS, both the wsAPRadioTspecApInactivityTimeout and the wsAPRadioTspecStaInactivityTimeout must expire in order for the TS to be deleted by the AP due to inactivity. If either of these timeouts is disabled, the AP will not delete a bidirectional TS due to inactivity. This value is specified in seconds. Setting this object value to 0 disables this timeout.

OBJECT-TYPE

Specifies the amount of time that an active traffic stream (TS) in the uplink direction may be idle, from the perspective of the AP, before it is deleted by the AP. For a bidirectional TS, both the wsAPRadioTspecApInactivityTimeout and the wsAPRadioTspecStaInactivityTimeout must expire in order for the TS to be deleted by the AP due to inactivity. If either of these timeouts is disabled, the AP will not delete a bidirectional TS due to inactivity. This value is specified in seconds. Setting this object value to 0 disables this timeout.

OBJECT-TYPE

When enabled, the AP allows intermixing of legacy traffic with Wi-Fi Multimedia (WMM) traffic on access category queues that are operating according to admission control mandatory (ACM) rules. This mode is intended for use with non Wi-Fi Multimedia Enabled (non-WME) clients and is disabled by default. When this object is set to enable(1), both the voice and video access categories are accessible by wireless clients that do not have an admitted TSPEC, which can lead to underestimation of the available medium time by wireless TSPEC admission control. Use caution when enabling this mode and also consider using very small ACM limit values as well.

OBJECT-TYPE

This table contains MCS indices that can be configured within an AP Profile per radio interface.

OBJECT-TYPE

Each entry in this table represents an MCS index that can be configured per radio interface within an AP profile.

OBJECT-TYPE

Indicates an index value available for use with the Modulation and Coding Scheme (MCS) for 802.11n connections. Not all radios support index values from 16 to 23.

OBJECT-TYPE

Indicates that the associated index value has or has not been configured for use with the Modulation and Coding Scheme (MCS) for 802.11n connections.

OBJECT-IDENTITY

OBJECT-TYPE

Indicates the server IP address to use for an AP code download request.

OBJECT-TYPE

The AP image type capability table contain parameters that are configurable for each image type download.

OBJECT-TYPE

Each entry provides image type capability details for each AP image type supported by the WS.

OBJECT-TYPE

Indicates the file path on the server to use for an AP code download request.

OBJECT-TYPE

Indicates file on the server to use for an AP code download request.

OBJECT-TYPE

Indicates an AP MAC address to use in a code download request for a single AP. MAC address zero indicates the code download request is for all managed APs. Setting this object initiates the code download. A read on this object always returns zero.

OBJECT-TYPE

Indicates the number of APs the wireless controller will issue a code download request to at one time.

OBJECT-TYPE

Indicates which image to download to the AP(s). Configurable values are: - tq3600, if download is for APs with hardware that only require tq3600 code - image2, reserved future - image3, reserved future - tq2450, if download is for APs with hardware that only require tq2450 code - tq4400, if download is for APs with hardware that only require tq4400 code - tq4600, if download is for APs with hardware that only require tq4600 code - tq3200, if download is for APs with hardware that only require tq3200 code - tq3400, if download is for APs with hardware that only require tq3400 code - all, if download involves APs that require tq3600, tq2450, tq4400, tq4600, tq3200, and tq3400 code

OBJECT-TYPE

This indicates the current status for an AP code download request. Default value is not started.

OBJECT-TYPE

Indicates the number of WS managed APs at the time a code download request is started. Value is 1 if a download request is for single AP.

OBJECT-TYPE

Indicates the total number of APs that have successfully completed code download.

OBJECT-TYPE

Indicates the total number of APs that have failed to complete a code download.

OBJECT-TYPE

Indicates the total number of APs aborted from the code download.

OBJECT-TYPE

Abort the current code download on managed AP(s). Supported values: disable(0) - Code download is not to be aborted. enable(1) - Code download is to be aborted.

OBJECT-IDENTITY

OBJECT-TYPE

This table displays the channel plan parameters.

OBJECT-TYPE

Each entry in this table will indicate the channel plan parameters for specific radio frequency.

OBJECT-TYPE

This object indicates the whether the channel plan is for ieee802dot11bORgn or ieee802dot11an.

OBJECT-TYPE

Indicates mode of computing and applying channel adjustments for managed AP radios operating in 2.4Ghz and 5Ghz band.

OBJECT-TYPE

If channel plan mode is interval, this object indicates a regular interval in minutes at which to compute and apply a new channel adjustments.

OBJECT-TYPE

If channel plan mode is time, this object indicates the next scheduled time in minutes at which to compute and apply a new channel adjustments. Zero minutes stands for mid-night.

OBJECT-TYPE

Indicates the maximum number of previously applied channel algorithm iterations stored on the controller and used in the next channel adjustment computation.

OBJECT-TYPE

Indicates whether or not automatic channel adjustment is operating for managed AP radios operating in 2.4Ghz and 5Ghz band.

OBJECT-TYPE

Indicates the current iteration of channel plan adjustments for managed AP radio.

OBJECT-TYPE

This action object is used to: - Run the Proposed Channel Adjustment alogorithm - Abort the channel plan. - Clear the calculated 2.4Ghz and 5Ghz channel plan. Read on this object will always return none.

OBJECT-TYPE

Indicates the current state of a manual request to compute or apply proposed channel adjustments.

OBJECT-TYPE

The time since the last channel plan algorithm ran.

OBJECT-TYPE

The minimum signal strength (dBm) with which a neighbor must be detected on the current operational channel in order for the channel plan to consider moving away from the current channel.

OBJECT-TYPE

When enabled, the channel plan does not take into account the interfering unmanaged APs. Only managed APs are used for generating the channel plan.

OBJECT-TYPE

Number of radios operating in the band. This includes the radios with static channel assignment.

OBJECT-TYPE

Indicates the number of AP radios analyzed by the channel algorithm. This includes APs that operate on static channels.This value is reset at the start of each channel plan cycle.

OBJECT-TYPE

Indicates the number of AP radios for which a Channel Plan Request has been sent by the channel algorithm.This value is reset at the start of each channel plan cycle.

OBJECT-TYPE

Indicates the number of AP radios whose operating channel changed. This includes APs whose channel is changed to the same channel as the original operating channel.This value is reset at the start of each channel plan cycle.

OBJECT-TYPE

Indicates the number of AP radios that scanned the candidate channels but ended on the same channel.This value is reset at the start of each channel plan cycle.

OBJECT-TYPE

The time for the estimated time of completion of the current channel plan cycle. When the channel plan is inactive the time stamp is zeroed out.

OBJECT-TYPE

During the channel plan cycle this parameter is the percentage of the AP radios that have been analyzed. When the channel plan is inactive this value is 0.

OBJECT-TYPE

The number of dBm by which to reduce the Channel Change Threshold for detected managed APs based on the Transmit Power of the detected managed APs.

OBJECT-TYPE

The number of seconds to wait before triggering the channel plan after a managed AP fails.

OBJECT-TYPE

When this administrative parameter is enabled, the controller runs ACA algorithm after it detects that a managed AP failed.

OBJECT-TYPE

This table contains parameters related to channel plan algorithm history, each entry indicates a previously computed and applied channel adjustment for the specified iteration. The maximum number of channel adjustment iterations displayed is based on the 802.11b/g or 802.11a channel plan history depth.

OBJECT-TYPE

Each entry in this table represents channel plan history for WS managed AP radio.

OBJECT-TYPE

This object indicates the whether the channel adjustment is for 2.4Ghz or 5Ghz band.

OBJECT-TYPE

The Ethernet address of the AP.

OBJECT-TYPE

Indicates the radio interface for channel assignment.

OBJECT-TYPE

A descriptive name of the AP, usually represented by its location.

OBJECT-TYPE

This field indicates the iteration of the channel plan algorithm for this channel adjustment, the maximum history depth is configurable. This history prevents the same APs from being changed time after time.

OBJECT-TYPE

Indicates the previously applied channel for this radio.

OBJECT-TYPE

This table contains parameters related to proposed channel plan adjustment. These parameters are applicable only when channel plan mode is manual.

OBJECT-TYPE

Each entry in this table represents proposed channel plan adjustment.

OBJECT-TYPE

This object indicates the whether the channel plan is for 2.4Ghz or 5Ghz band.

OBJECT-TYPE

The Ethernet address of the AP.

OBJECT-TYPE

Indicates the radio interface for channel assignment.

OBJECT-TYPE

Indicates the current operating channel for this radio.

OBJECT-TYPE

Indicates new channel assignment for this radio.

OBJECT-TYPE

Flag to set automatic power adjustment for all managed AP radios. If power adjustment mode is interval, periodically calculate the power adjustments and apply them. However, if power adjustment is manual, calculation and assignment of power adjustments initiated and controlled by the administrator user interface commands.

OBJECT-TYPE

Power Plan signal strength threshold in dBm.

OBJECT-TYPE

This action object is used to: - Run the Proposed Power Adjustment alogorithm - Apply the same to network. - Clear the calculated power plan. Read on this object will always return none.

OBJECT-TYPE

Indicates the current state of a manual request to compute or apply proposed power adjustments.

OBJECT-TYPE

This table represents the proposed power adjustment status parameters. These parameters are displayed only when power adjustment mode is set to manual. The administrator manually apply all of the proposed power adjustments displayed.

OBJECT-TYPE

Each entry in this table represents the proposed power adjustment status parameters.

OBJECT-TYPE

The Ethernet address of the AP.

OBJECT-TYPE

Indicates the radio interface for power assignment.

OBJECT-TYPE

Indicates the current operating power for this radio from the last power plan computation. Even after the new power plan is applied, this object displays the old value as opposed to the actual power currently set into the radio.

OBJECT-TYPE

Indicates the new proposed power assignment for this radio.

OBJECT-TYPE

The Operational Status of the Power Plan Algorithm.

OBJECT-TYPE

The average number of managed radios detected by every operational mode radio in the cluster.

OBJECT-TYPE

The average number of managed virtual APs detected by every operational mode radio in the cluster.

OBJECT-TYPE

The number of operational mode radios in the cluster. The sentry and disabled radios are not counted.

OBJECT-TYPE

Number of power plan cycles executed by the controller.

OBJECT-TYPE

Number of transmit power changes done by the power plan algorithm for all radios in the cluster.

OBJECT-TYPE

Number of transmit power increases done by the power plan algorithm for all radios in the cluster.

OBJECT-TYPE

Number of transmit power reductions done by the power plan algorithm for all radios in the cluster.

OBJECT-TYPE

Time since the last power plan was done. The power plan could have been triggered manually or automatically.

OBJECT-TYPE

This table contains the per band per radio channel plan status for a Managed AP.

OBJECT-TYPE

Each entry in this table represents channel plan per band per radio status for WS managed AP.

OBJECT-TYPE

This object indicates the whether the channel plan is for ieee802dot11bORgn or ieee802dot11an.

OBJECT-TYPE

The Ethernet address of the Managed AP.

OBJECT-TYPE

Indicates the radio interface for channel assignment.

OBJECT-TYPE

Flag Indicating whether the AP is managed by the cluster controller or a peer controller.

OBJECT-TYPE

Indicates the current operating channel for this radio.

OBJECT-TYPE

Channel on which this radio was operating before the channel change algorithm changed its channel.

OBJECT-TYPE

The strongest signal detected on the old channel. This is the signal used in the channel selection decision.

OBJECT-TYPE

The strongest signal detected on the new channel during the channel validation scan. This is the signal used in the channel selection decision. If the algorithm does not change the channel then this is the signal on the current channel detected during the channel check scan.

OBJECT-TYPE

Flag indicating whether the last channel plan cycle changed the channel for this radio.

OBJECT-TYPE

The reason code indicating why the channel was changed or not changed for this radio.

OBJECT-TYPE

The MAC address and the signal strength of the strongest managed neighbor AP detected on the channel before that channel was changed. The MAC address is the base MAC of the managed AP.

OBJECT-TYPE

The MAC address and the signal strength of the strongest managed neighbor AP detected on the current operating channel. The MAC address is the base MAC of the managed AP.

OBJECT-TYPE

The MAC address and the signal strength of the strongest unmanaged neighbor AP detected on the channel before that channel was changed.

OBJECT-TYPE

The MAC address and the signal strength of the strongest unmanaged neighbor AP detected on the current operating channel.

OBJECT-TYPE

The UTC time since the channel was last changed by the channel plan algorithm..

OBJECT-TYPE

Number of milliseconds that the AP spent scanning channels during the last channel plan cycle. The scan time includes the operational channel scan, so the time may be non-zero even when the radio did not change channels.

OBJECT-TYPE

This table contains the per radio Power Plan Status for a Managed AP .

OBJECT-TYPE

Each entry in this table represents the per radio power plan status for WS managed AP.

OBJECT-TYPE

The Ethernet address of the Managed AP.

OBJECT-TYPE

Indicates the radio interface of the Managed AP.

OBJECT-TYPE

Flag Indicating whether the AP is managed by the cluster controller or a peer controller.

OBJECT-TYPE

Channel on which the radio is operating. For sentry radios this field is set to sentry. The disabled radios report None.

OBJECT-TYPE

The current operating power for this radio. Sentry radios and disabled radios report 0%.

OBJECT-TYPE

The number of APs managed by this cluster detected by this radio on the operational channel.

OBJECT-TYPE

The number of VAPs managed by this cluster detected by this radio on the operational channel.

OBJECT-TYPE

The base MAC address of the managed AP that detects this radio with the strongest signal.

OBJECT-TYPE

The radio number of the managed AP that detects this radio with the strongest signal.

OBJECT-TYPE

The strongest signal strength in dBm with which a managed neighbor detects this radio.

OBJECT-TYPE

The MAC address of the AP that this radio detects with the strongest signal.

OBJECT-TYPE

The signal strength with which this radio detects the strongest neighbor.

OBJECT-TYPE

The status indicating whether the power was changed during the most recent cycle of the power adjustment algorithm.

OBJECT-TYPE

The reason code indicating why the last power adjustment action was taken or not taken.

OBJECT-TYPE

Number of transmit power changes done by the power plan algorithm for this radio.

OBJECT-TYPE

Number of transmit power increases done by the power plan algorithm for this radio.

OBJECT-TYPE

Number of transmit power reductions done by the power plan algorithm for this radio.

OBJECT-TYPE

This table contains the per profile power plan status.

OBJECT-TYPE

Each entry in this table represents the per profile power plan status.

OBJECT-TYPE

Indicates the profile Id.

OBJECT-TYPE

The average number of managed radios detected by every operational mode radio that uses this profile. If the number of APs is greater than 999 then it is reported as 999..

OBJECT-TYPE

The average number of managed virtual APs detected by every operational mode radio that uses this profile.

OBJECT-TYPE

Number of transmit power changes done by the power plan algorithm for all radios in this profile.

OBJECT-TYPE

Number of transmit power increases done by the power plan algorithm for all radios in this profile.

OBJECT-TYPE

Number of transmit power reductions done by the power plan algorithm for all radios in this profile.

OBJECT-TYPE

This action object is used to: - start the network provision. - stop the network provision.

OBJECT-TYPE

The Operational Status of the Initial Network Provisioning Protocol.

OBJECT-TYPE

Number of seconds the latest invocation of the protocol has been running.

OBJECT-TYPE

Percent complete for the channel protocol in the 2.4 GHz band.

OBJECT-TYPE

Percent complete for the channel protocol in the 5GHz band.

OBJECT-TYPE

Count-Down of how many power plan interations remain to be done.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains status parameters for all APs managed by the controller.

OBJECT-TYPE

Each entry in this table contains status parameters for an AP managed by the controller. Controller can managed up to 48 APs at a time, with the actual maximum number supported dependent on the CPU performance of the controller and may be smaller or larger for some implementations.

OBJECT-TYPE

Ethernet address of the WS managed AP.

OBJECT-TYPE

Network IP address of the managed AP.

OBJECT-TYPE

Indicates vendor of the WS managed AP software. Broadcom vendor ID is 1.

OBJECT-TYPE

Indicates software version of the WS managed AP.

OBJECT-TYPE

Indicates hardware platform of the WS managed AP.

OBJECT-TYPE

Indicates serial number of the WS managed AP.

OBJECT-TYPE

Indicates hardware part number of the WS managed AP.

OBJECT-TYPE

Indicates discovery method used to detect the AP.

OBJECT-TYPE

Indicates current state of an AP.

OBJECT-TYPE

Indicates total number of clients currently authenticated to an AP.

OBJECT-TYPE

Indicates time in seconds since last power-on reset.

OBJECT-TYPE

The configuration profile currently applied to the AP.

OBJECT-TYPE

The descriptive name for the profile currently applied to the AP.

OBJECT-TYPE

Indicates the protocol version supported by the software on the AP.

OBJECT-TYPE

This indicates the current status of a code download request for this AP.

OBJECT-TYPE

A descriptive name for the AP, usually represented by location.

OBJECT-TYPE

Indicates the element Id of the last failing configuration element.

OBJECT-TYPE

Indicates an ASCII string filled in by the AP, containing the error message.

OBJECT-TYPE

This is an action object. Setting this object to enable will reset the AP. Read on this object will always return disable.

OBJECT-TYPE

This object gives status regarding the AP that got reset.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge the failed AP entry. Read on this object will always return disable.

OBJECT-TYPE

Indicates password to be used for debugging managed AP. User should enable debug mode to set debug password. If password is configured, read on this object will return '*****'.

OBJECT-TYPE

This is an action object. Enabling this object will enable the telnet access to the managed AP.

OBJECT-TYPE

This object indicates the status of the debug action requested when managed AP debug mode is set.

OBJECT-TYPE

Time since last communication with an AP.

OBJECT-TYPE

This object indicates whether the AP is managed by this controller or peer-controller.

OBJECT-TYPE

MAC address of the WS managing the AP.

OBJECT-TYPE

IP address of the WS managing the AP.

OBJECT-TYPE

Network IP mask of the managed AP.

OBJECT-TYPE

Number of clients using this AP as a Home AP. It is also the number of clients that roamed away from this AP and are tunneling data back to it.

OBJECT-TYPE

Number of clients using this AP as an association AP. It is also the number of clients that roamed to this AP and are tunneling data back to the Home AP.

OBJECT-TYPE

Total number of APs to which this AP establishes distributed tunnels.

OBJECT-TYPE

Maximum number of tunnels on the home AP that are members of the same VLAN.

OBJECT-TYPE

The VLAN ID over which the max number of multicast replications are sent into the distributed tunnels.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge all the managed AP failed entries. Read on this object will always return disable.

OBJECT-TYPE

This table contains statistics available for each AP managed by the controller.

OBJECT-TYPE

Each entry in this table contain statistics available for each AP managed by the controller.

OBJECT-TYPE

Total packets received by an AP on the wireless network.

OBJECT-TYPE

Total bytes received by an AP on the wireless network.

OBJECT-TYPE

Total packets transmitted by an AP on the wireless network.

OBJECT-TYPE

Total bytes transmitted by an AP on the wireless network.

OBJECT-TYPE

Total packets received by an AP on the wired network.

OBJECT-TYPE

Total bytes received by an AP on the wired network.

OBJECT-TYPE

Total multicast packets received by an AP on the wired network.

OBJECT-TYPE

Total packets transmitted by an AP on the wired network.

OBJECT-TYPE

Total bytes transmitted by an AP on the wired network.

OBJECT-TYPE

Total transmit errors detected by an AP on the wired network.

OBJECT-TYPE

Total receive errors detected by an AP on the wired network.

OBJECT-TYPE

Total bytes received via central L2 tunnel by the AP.

OBJECT-TYPE

Total packets received via central L2 tunnel by the AP.

OBJECT-TYPE

Total multicast packets received via central L2 tunnel by the AP.

OBJECT-TYPE

Total bytes transmitted via central L2 tunnel by the AP.

OBJECT-TYPE

Total packets transmitted via central L2 tunnel by the AP.

OBJECT-TYPE

Total multicast packets transmitted via central L2 tunnel by the AP.

OBJECT-TYPE

Total packets dropped in the receive direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the receive direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the transmit direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the transmit direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total Bytes transmitted by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total Bytes received by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total packets transmitted by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total packets received by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total multicast packets transmitted by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total multicast packets received by the AP through all the established Distributed Tunnels.

OBJECT-TYPE

Total number of clients that used this AP for Distributed Tunneling. This inclides clients that roamed away from and to this AP.

OBJECT-TYPE

Number of client tunnel sessions that were terminated because of not sending the traffic through the tunnel after roaming.

OBJECT-TYPE

Number of client tunnel sessions that were terminated because of expiry of the tunnel session.

OBJECT-TYPE

Number of client tunnel session setup denials by the AP because of reaching the maximum configured client limit.

OBJECT-TYPE

Number of client tunnel setup denials by the AP because of reaching the maximum configured VLAN replications limit.

OBJECT-TYPE

Total number of ARP requests converted from broadcast to unicast packet before transmitting on wireless network.

OBJECT-TYPE

Total number of ARP requests filtered by the wireless ARP suppression logic.

OBJECT-TYPE

Total number of ARP requests broadcasted on to the wireless network after being processed by wireless ARP suppression logic.

OBJECT-TYPE

This table contains status parameters per radio interface for all the APs managed by controller.

OBJECT-TYPE

Each entry in this table contains status parameters per radio interface for an AP managed by the controller.

OBJECT-TYPE

The physical radio interface on the AP.

OBJECT-TYPE

The MAC address of the physical radio.

OBJECT-TYPE

If the radio is operational, the current transmit channel for this radio interface.

OBJECT-TYPE

If the radio is operational, the current transmit power of the radio.

OBJECT-TYPE

Total count of clients authenticated on the physical radio.

OBJECT-TYPE

Total network utilization for the physical radio. This value is based on radio statistics.

OBJECT-TYPE

This flag indicates if a fixed channel is configured and assigned to the radio.

OBJECT-TYPE

Indicates the current state of a manual request to change the channel on this radio.

OBJECT-TYPE

This flag indicates if a fixed power setting is configured and assigned to the radio.

OBJECT-TYPE

Indicates the current state of a manual request to change the power setting on this radio.

OBJECT-TYPE

Total number of neighbors that can be seen by this radio in its RF area.

OBJECT-TYPE

This is an action object. When we set this object to apply, along with wsManagedAPRadioFixedChannel, controller starts applying fixed channel assignment for this radio. Read on this object will always return none.

OBJECT-TYPE

This object is used to assign the fixed channel for this radio on this Managed AP. The following MIB objects get changed on successful setting of this MIB object - 1. wsManagedAPRadioChannel --> changes to the channel set here 2. wsManagedAPRadioFixedChannelIndicator --> changes to 'yes (2)' Read on this object will always return 0.

OBJECT-TYPE

This is an action object. When we set this object to apply, controller starts applying fixed power adjustment for this radio. Read on this object will always return none.

OBJECT-TYPE

This object is used to assign the fixed power for this radio on this Managed AP. The following MIB objects get changed on successful setting of this MIB object - 1. wsManagedAPRadioTxPower --> changes to the power set here 2. wsManagedAPRadioFixedPowerIndicator --> changes to 'yes (2)' Read on this object will always return 0.

OBJECT-TYPE

Current Channel Bandwidth In Use.

OBJECT-TYPE

Current state of enablement for Radio Resource Management (RRM).

OBJECT-TYPE

This table contains statistics available for each physical radio on an AP managed by the controller.

OBJECT-TYPE

Each entry in this table contain statistics available for each physical radio on an AP managed by controller.

OBJECT-TYPE

Total packets received by an AP on this radio interface.

OBJECT-TYPE

Total bytes received by an AP on this radio interface.

OBJECT-TYPE

Total packets transmitted by an AP on this radio interface.

OBJECT-TYPE

Total bytes transmitted by an AP on this radio interface.

OBJECT-TYPE

Count of acknowledged MPDU with an individual address or an MPDU with a multicast address of type data or management.

OBJECT-TYPE

Count of successfully transmitted MSDU frames where the multicast bit is set in the destination MAC address.

OBJECT-TYPE

Number of times a MSDU is not transmitted successfully due to transmit attempts exceeding either the short retry limit or the long retry limit.

OBJECT-TYPE

Number of times a MSDU is successfully transmitted after one or more retries.

OBJECT-TYPE

Number of times a MSDU is successfully transmitted after more than one retry.

OBJECT-TYPE

Number of times a frame is received and sequence control field indicates is a duplicate.

OBJECT-TYPE

Count of CTS frames received in response to the RTS frames.

OBJECT-TYPE

Count of CTS frames not received in response to the RTS frames.

OBJECT-TYPE

Count of ACK frames not received when expected.

OBJECT-TYPE

Count of successfully received MPDU frames of type data or management.

OBJECT-TYPE

Count of MSDU frames received with the multicast bit set in the destination MAC address.

OBJECT-TYPE

Count of FCS errors detected in a received MPDU frame.

OBJECT-TYPE

Count of each successfully transmitted MSDU.

OBJECT-TYPE

Count of encrypted frames received and the key configuration of the transmitter indicates that the frame should not have been encrypted or that frame was discarded due to the receiving station not implementing the privacy option.

OBJECT-TYPE

Total packets dropped in the receive direction on this radio interface. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the receive direction on this radio interface. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the transmit direction by this radio interface. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the transmit direction by this radio interface. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

This table contains neighbor AP list.

OBJECT-TYPE

Each entry in this table contains neighbor AP information.

OBJECT-TYPE

The MAC address of neighbor AP network. This could be a physical radio MAC or VAP MAC address.

OBJECT-TYPE

Service Set ID of neighbor AP network.

OBJECT-TYPE

This object indicates Received Signal Strength(RSSI) from the neighbor radios in a given channel.

OBJECT-TYPE

Indicates managed status of the AP.

OBJECT-TYPE

Indicates time since this AP was last detected.

OBJECT-TYPE

This is an action object used to purge the AP neighbor entries. Read on this object will always return disable.

OBJECT-TYPE

This table contains neighbor client list currently detected by an RF scan on the radio.

OBJECT-TYPE

Each entry in this table contain neighbor client information.

OBJECT-TYPE

The MAC address of neighbor client station.

OBJECT-TYPE

Indicates RSSI from neighbor clients on the radio.

OBJECT-TYPE

Indicates AP channel, on which the client frame was received.

OBJECT-TYPE

Indicates time since a client was last detected.

OBJECT-TYPE

Indicates discovery methods for the neighbor client.

OBJECT-TYPE

This table contains status parameters for each VAP configured on a radio interface for a WS managed AP.

OBJECT-TYPE

Each entry in this table contains status parameters of each VAP configured on radio.

OBJECT-TYPE

Indicates VAP Id.

OBJECT-TYPE

Indicates the ethernet address of the VAP MAC address.

OBJECT-TYPE

Network assigned to a VAP MAC Address.

OBJECT-TYPE

Number of clients currently authenticated to VAP.

OBJECT-TYPE

This table contains statistics available for each VAP on the WS managed AP.

OBJECT-TYPE

Each entry in this table contain statistics available for each VAP on the WS managed AP.

OBJECT-TYPE

Number of clients that have been denied association to the VAP.

OBJECT-TYPE

Number of clients that have failed authentication to the VAP.

OBJECT-TYPE

Total packets received by an AP on this VAP.

OBJECT-TYPE

Total bytes received by an AP on this VAP.

OBJECT-TYPE

Total packets transmitted by an AP on this VAP.

OBJECT-TYPE

Total bytes transmitted by an AP on this VAP.

OBJECT-TYPE

Total packets dropped in the receive direction by an AP on this VAP. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the receive direction by an AP on this VAP. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.

OBJECT-TYPE

Total packets dropped in the transmit direction by an AP on this VAP. This is due to client QoS actions affecting the wireless down (outbound) direction from client to AP.

OBJECT-TYPE

Total bytes dropped in the transmit direction by an AP on this VAP. This is due to client QoS actions affecting the wireless down (outbound) direction from client to AP.

OBJECT-TYPE

This is an action object. Setting this object to enable will reset all the managed APs. Read on this object will always return disable.

OBJECT-TYPE

This table represents eligible channel entries for an AP radio to consider for channel algorithm. It is based on country code, hardware capabilities and any configured channel limitations.

OBJECT-TYPE

Each entry in this table represents eligible channel for an AP radio.

OBJECT-TYPE

Indicates list of supported channel by the managed ap. List contains one or more entries from 1-255, actual range is determined by physical mode and country code.

OBJECT-TYPE

This flag indicates if radar detection is enabled or not on this channel.

OBJECT-TYPE

This flag indicates if radar is detected or not on this channel.

OBJECT-TYPE

Indicates the time in seconds since last radar was detected.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains status parameters of clients that are currently associated with managed APs.

OBJECT-TYPE

Each entry in this table contain client status parameters assocaited with the WS managed AP.

OBJECT-TYPE

Associated client MAC address.

OBJECT-TYPE

Indicates network IP address of the client station, 0.0.0.0 indicates unknown. Tunnel IP subnet is present only for clients authenticated with tunneled VAPs.

OBJECT-TYPE

Indicates user name of the client that have authenticated via 802.1x, clients on networks with other security modes will not have a user name.

OBJECT-TYPE

Indicates the network on which the client is connected.

OBJECT-TYPE

If client is on VAP using VLAN data forwarding mode, indicates obsolete assigned VLAN.

OBJECT-TYPE

This object indicates client's status.

OBJECT-TYPE

Indicates the data rate, AP will actually support in setting up communications with client stations represented by a count from 2 - 1200, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 600 Mbit/s. Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.

OBJECT-TYPE

For a current association, period of time that the AP has not seen any traffic for the client.

OBJECT-TYPE

This is an action object. Setting this object to start will initiate the disassociation of associated client. Read on this object will always return none.

OBJECT-TYPE

Indicates time since the controller has received new data for this client.

OBJECT-TYPE

This object indicates whether the client is associated to an AP managed by this controller or peer-controller.

OBJECT-TYPE

MAC address of the WS associating the client.

OBJECT-TYPE

IP address of the WS associating the client.

OBJECT-TYPE

Flag indicating whether this client is capable of 802.11n operation.

OBJECT-TYPE

Flag indicating whether this client is capable of Space Time Block Code (STBC) operation.

OBJECT-TYPE

Indicates whether L2 Distributed Tunneling is Enabled or Disabled

OBJECT-TYPE

Indicates whether the client is using the distrubuted tunnel or not. Also indicates if it is a roamed client or not.

OBJECT-TYPE

Indicates MAC Address of the client's Home AP. Here the client should be associated with the network on which the L2 Distributed Tunneling is enabled.

OBJECT-TYPE

MAC Address of the client's Association AP to which the client has roamed to.

OBJECT-TYPE

MAC Address of the AP to which client is Associated.

OBJECT-TYPE

BSSID of the VAP to which client is associated.

OBJECT-TYPE

Indicates the radio interface on which client is associated.

OBJECT-TYPE

Indicates channel for associated client entry.

OBJECT-TYPE

Indicates time since this client first authenticated with the network.

OBJECT-TYPE

Indicates network IPv4 address of the client station detetecd through ARP snooping, 0.0.0.0 indicates unknown.

OBJECT-TYPE

NetBios Name of the client.

OBJECT-TYPE

Indicates if the Radio Resource Management (RRM) portion of the IEEE 802.11k standard is supported by client and RRM is enabled is on the AP Profile. Value 2 indicates the client supports RRM portion and RRM Mode is not enabled on AP Profile. Value 3 indicates client doesnot support RRM

OBJECT-TYPE

Indicates if the client can support RRM location report requests.

OBJECT-TYPE

Indicates if the client can detect APs via RRM beacon table reports.

OBJECT-TYPE

Indicates if the client supports active scan capability.

OBJECT-TYPE

Indicates if the client supports passive scan capability.

OBJECT-TYPE

Indicates if the client supports RRM channel load measurement.

OBJECT-TYPE

This table contains statistics available for each client associated to a WS managed AP.

OBJECT-TYPE

Each entry in this table contain statistics available for each client associated a WS managed AP.

OBJECT-TYPE

Total packets received by a managed AP from the client station.

OBJECT-TYPE

Total bytes received by a managed AP from the client station.

OBJECT-TYPE

Total packets transmitted by a managed AP to the client station.

OBJECT-TYPE

Total bytes transmitted by a managed AP to the client station.

OBJECT-TYPE

Total duplicate packets received from the client station.

OBJECT-TYPE

Total fragmented packets received from the client station.

OBJECT-TYPE

Total fragmented packets transmitted to the client station.

OBJECT-TYPE

Indicates number of times transmits to client station succeeded after one or more retries.

OBJECT-TYPE

Number of times transmits to client station failed after one or more retries.

OBJECT-TYPE

Total packets dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.

OBJECT-TYPE

Total bytes dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.

OBJECT-TYPE

Total packets dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Number of packets received by the AP from a client station that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.

OBJECT-TYPE

Number of packets transmitted by the AP to a client station that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.

OBJECT-TYPE

This table is maintained to lookup all WS managed APs detected, client can see in its RF area.

OBJECT-TYPE

Each entry in this table contain WS managed APs that can be seen by client in its RF area.

OBJECT-TYPE

The Ethernet address of a client station.

OBJECT-TYPE

The Ethernet address of a WS managed AP.

OBJECT-TYPE

The radio interface of Managed AP.

OBJECT-TYPE

Indicates the client status with respect to the Managed AP it is refering. One or more flags can be enabled at the same time.

OBJECT-TYPE

This table is maintained to lookup clients associated to a specific VAP on a WS managed AP.

OBJECT-TYPE

Each entry in this table contain clients associated to each VAP.

OBJECT-TYPE

The Ethernet address assigned to a VAP.

OBJECT-TYPE

The Ethernet address of associated client station.

OBJECT-TYPE

This table is maintained to lookup all clients associated to a particular network.

OBJECT-TYPE

Each entry in this table contain clients associated to a particular network.

OBJECT-TYPE

Indicates the network on which the client is connected.

OBJECT-TYPE

The Ethernet address of the client station.

OBJECT-TYPE

This table is maintained to lookup clients associated to the APs managed by the specific controller.

OBJECT-TYPE

Each entry in this table contain client associated to each controller.

OBJECT-TYPE

IP address of the WS associating the client.

OBJECT-TYPE

Ethernet address of the associated client station.

OBJECT-TYPE

This table contains client QoS status parameters of clients that are currently associated with managed APs. These objects represent the actual operational status values in effect for the clients.

OBJECT-TYPE

Each entry in this table contains client QoS status parameters for a client associated with the WS managed AP.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.

OBJECT-TYPE

Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosAccessControlDownName object identifies the access list.

OBJECT-TYPE

Name of the access list in use in accordance with the wsAssociatedClientQosAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.

OBJECT-TYPE

Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosAccessControlUpName object identifies the access list.

OBJECT-TYPE

Name of the access list in use in accordance with the wsAssociatedClientQosAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.

OBJECT-TYPE

DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosDiffservPolicyDownName object identifies the DiffServ policy.

OBJECT-TYPE

Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-TYPE

DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosDiffservPolicyUpName object identifies the DiffServ policy.

OBJECT-TYPE

Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-TYPE

Designates the AP quality-of-service operational status for this wireless client. This represents the combined states of the wsApClientQosMode object and the wsNetworkClientQosMode object for the wireless network to which this client is associated.

OBJECT-TYPE

This table contains statistics available for each client associated to a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.

OBJECT-TYPE

Each entry in this table contain statistics available for each client associated a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.

OBJECT-TYPE

Total packets received by managed APs from the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Total bytes received by managed APs from the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Total packets transmitted by managed APs to the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Total bytes transmitted by managed APs to the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Total duplicate packets received from the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Total fragmented packets received from the client station. throughout the duration of the current WLAN session.

OBJECT-TYPE

Total fragmented packets transmitted to the client station throughout the duration of the current WLAN session.

OBJECT-TYPE

Indicates number of times transmits to client station succeeded after one or more retries throughout the duration of the current WLAN session.

OBJECT-TYPE

Number of times transmits to client station failed after one or more retries throughout the duration of the current WLAN session.

OBJECT-TYPE

Total packets dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.

OBJECT-TYPE

Total bytes dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.

OBJECT-TYPE

Total packets dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Total bytes dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.

OBJECT-TYPE

Number of packets received by managed APs from a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.

OBJECT-TYPE

Number of packets transmitted by managed APs to a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.

OBJECT-TYPE

This table contains cached client QoS status parameters of clients that are currently associated with managed APs. These objects represent values that were retrieved from a RADIUS server for this client. See the wsAssociatedClientQosStatusTable for the current set of operational values in use for this client.

OBJECT-TYPE

Each entry in this table contains client QoS cached status parameters for a client associated with the WS managed AP. Only those parameters successfully retrieved from a RADIUS server via 802.1X authentication on behalf of a wireless client are displayed.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.

OBJECT-TYPE

Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.

OBJECT-TYPE

Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosCachedAccessControlDownName object identifies the access list.

OBJECT-TYPE

Name of the access list in use in accordance with the wsAssociatedClientQosCachedAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.

OBJECT-TYPE

Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosCachedAccessControlUpName object identifies the access list.

OBJECT-TYPE

Name of the access list in use in accordance with the wsAssociatedClientQosCachedAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.

OBJECT-TYPE

DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosCachedDiffservPolicyDownName object identifies the DiffServ policy.

OBJECT-TYPE

Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosCachedDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-TYPE

DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosCachedDiffservPolicyUpName object identifies the DiffServ policy.

OBJECT-TYPE

Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosCachedDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.

OBJECT-IDENTITY

OBJECT-TYPE

This table contain status parameters of peer controllers of wireless controller.

OBJECT-TYPE

Each entry describes the status parameters of each peer of wireless controller.

OBJECT-TYPE

IP address of the peer controller.

OBJECT-TYPE

Indicates if the peer controller is currently the Cluster Controller of the peer group or not.

OBJECT-TYPE

Total number of peer controllers detected on the network.

OBJECT-TYPE

Indicates vendor of peer controller software.

OBJECT-TYPE

Indicates software version of peer controller.

OBJECT-TYPE

Indicates the protocol version of software on the peer controller.

OBJECT-TYPE

Indicates the discovery method of peer controller.

OBJECT-TYPE

Indicates time in seconds since last communication with the controller.

OBJECT-TYPE

Number of APs in the peer managed AP database that are authenticated, configured, and have an active connection with the wireless controller.

OBJECT-TYPE

This action object is used to: - start - Start the config push into the peer controller. - Read on this object will always return none.

OBJECT-TYPE

The status for the configuration push operation to this peer controller.

OBJECT-TYPE

IP Address of the last controller from which this controller received any wireless configuration data.

OBJECT-TYPE

Indicates which portions of configuration were last received from a peer controller. The combination of configurations are denoted by doing 'AND' of the values.BIT zero is ignored. Ex: Value 9 specifies only bit 2 and 5 are set, So it denotes channelPowerConfig and globalConfig received

OBJECT-TYPE

The last time this controller received any configuration data from a peer controller.

OBJECT-TYPE

This table contain Managed AP database of the peer controllers of wireless controller.

OBJECT-TYPE

Each entry describes the Managed AP Entry of the peer of wireless controller.

OBJECT-TYPE

The IP Address of the Peer controller.

OBJECT-TYPE

The VAP0 MAC address of the AP managed by the peer controller.

OBJECT-TYPE

This object indicates descriptive location of the managed AP by the peer controller.

OBJECT-TYPE

IP address for the peer managed AP.

OBJECT-TYPE

Unique ID for the peer managed AP's configuration profile.

OBJECT-TYPE

The descriptive name for the peer managed AP's configuration profile.

OBJECT-TYPE

The Hardware platform for the AP. 1 --> BROADCOM.

OBJECT-IDENTITY

OBJECT-TYPE

This table is maintained with RF scan data received from the WS managed APs.

OBJECT-TYPE

Each entry in this table contain RF scan data received from the WS managed AP.

OBJECT-TYPE

The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.

OBJECT-TYPE

If status indicates a managed AP, this indicates the radio interface on the Detected AP, if the value is unknown (i.e. Rogue or third party APs) it is set to '0'.

OBJECT-TYPE

If status indicates a managed AP, this indicates the base MAC address of the detected AP, If the value is unknown (i.e. Rogue of third party AP's) it is set to '0'.

OBJECT-TYPE

Service Set Id of the detected network.

OBJECT-TYPE

Indicates the 802.11 mode being used on an AP.

OBJECT-TYPE

Indicates transmit channel of an AP.

OBJECT-TYPE

Indicates the rate at which an AP is currently transmitting data, from 1 Mbit/s to 600 Mbit/s.

OBJECT-TYPE

Indicates beacon interval for a neighbor AP network.

OBJECT-TYPE

Indicates the managed status of an AP.

OBJECT-TYPE

Indicates timestamp in seconds when an AP was first detected.

OBJECT-TYPE

Indicates time in seconds since an AP was last detected in the scan.

OBJECT-TYPE

Indicates the initial status of an AP.

OBJECT-TYPE

Indicates the security mode of an AP.

OBJECT-TYPE

Indicates the highest supported rate advertised by an AP in Mbps.

OBJECT-TYPE

Indicates whether 802.11n is supported by an AP.

OBJECT-TYPE

Indicates that the beacon frame was received from an ad hoc network for an AP.

OBJECT-TYPE

Indicates that an AP is managed by a peer controller.

OBJECT-TYPE

Indicates whether rogue AP mitigation is in progress for an AP.

OBJECT-TYPE

This is a command that allows the administrator to restore the initial status for this AP in the RF Scan database. Read on this object will always return no-action.

OBJECT-TYPE

BSSID advertised in the network.

OBJECT-TYPE

Manufacturer information for this AP.

OBJECT-TYPE

Advertised status of Radio Resource Management (RRM) capability.

OBJECT-TYPE

Indicates whether 802.11ac is supported by an AP.

OBJECT-TYPE

This is an action object used to purge the RF scan entries present in the network. Read on this object will always return disable.

OBJECT-TYPE

This table contain status parameters of APs that failed to authenticate, or associate with wireless controller.

OBJECT-TYPE

Each entry in this table contain status parameters of failed AP.

OBJECT-TYPE

The Ethernet address of the failed AP.

OBJECT-TYPE

The network IP address of the failed AP.

OBJECT-TYPE

Indicates vendor of the failed AP.

OBJECT-TYPE

Indicates software version of the failed AP.

OBJECT-TYPE

Indicates hardware type of the failed AP.

OBJECT-TYPE

Indicates the last type of failure that occured.

OBJECT-TYPE

Number of times the AP failed to authenticate due to MAC address validation failure.

OBJECT-TYPE

Number of times the AP failed to authenticate due to incorrect authentication credentials.

OBJECT-TYPE

Indicates the protocol version supported by the software on this AP.

OBJECT-TYPE

Indicates time since failure occured.

OBJECT-TYPE

This object indicates whether the AP failure happened on this controller or on the peer-controller.

OBJECT-TYPE

MAC address of the WS reporting the AP Authentication Failure.

OBJECT-TYPE

IP address of the WS reporting the AP Authentication Failure.

OBJECT-TYPE

This is an action object used to purge the failed AP entries. Read on this object will always return disable.

OBJECT-TYPE

This table contains information related to Ad hoc clients detected in the network.

OBJECT-TYPE

Each entry in this table represents Ad hoc client detected in the network.

OBJECT-TYPE

The Ethernet address of the Ad hoc client detected. If detection Mode is 'Beacon' then the client is represented as an AP in the RF Scan database and the Neighbor AP List. If the detection mode is 'Data Frame' then the client information is in the Neighbor Client List.

OBJECT-TYPE

The MAC address of an AP which last detected the Ad hoc client.

OBJECT-TYPE

The radio interface of an AP which last detected the Ad hoc client.

OBJECT-TYPE

The mechanism through which this Ad hoc device is detected. This can be through beacon frame or data frame.

OBJECT-TYPE

Indicates time since the last detection of this Ad hoc client.

OBJECT-TYPE

This is an action object used to purge the ad-hoc client entries. Read on this object will always return disable.

OBJECT-TYPE

This table contains triangulation data to help the administrator determine which non-sentry APs are detecting the device.

OBJECT-TYPE

Each entry in this table contains triangulation information for the RF Scan entry.

OBJECT-TYPE

The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.

OBJECT-TYPE

Index of the sentry triangulation entry.

OBJECT-TYPE

The MAC address of the detecting AP.

OBJECT-TYPE

The radio of the detecting AP.

OBJECT-TYPE

Received signal strength indicator in percent (0 to 100%).

OBJECT-TYPE

Received signal strength in dBm (-127 to 127).

OBJECT-TYPE

Noise reported on the channel by the AP in dBm (-127 to 127).

OBJECT-TYPE

Indicates the age since this device was most recently detected by the detecting AP.

OBJECT-TYPE

This table contains triangulation data to help the administrator determine which sentry APs are detecting the device.

OBJECT-TYPE

Each entry in this table contains triangulation information for the RF Scan entry.

OBJECT-TYPE

The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.

OBJECT-TYPE

Index of the sentry triangulation entry.

OBJECT-TYPE

The MAC address of the detecting AP.

OBJECT-TYPE

The radio of the detecting AP.

OBJECT-TYPE

Received signal strength indicator in percent (0 to 100%).

OBJECT-TYPE

Received signal strength in dBm (-127 to 127).

OBJECT-TYPE

Noise reported on the channel by the AP in dBm (-127 to 127).

OBJECT-TYPE

Indicates age since this device was most recently detected by the detecting AP.

OBJECT-TYPE

This table contains rogue classification test results.

OBJECT-TYPE

Each entry in this table contains triangulation information for the RF Scan entry.

OBJECT-TYPE

The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.

OBJECT-TYPE

The rogue classification test id.

OBJECT-TYPE

The rogue classification test identifier.

OBJECT-TYPE

Indicates whether this test detected the condition that it is designed to detect.

OBJECT-TYPE

The MAC address of the managed AP that last reported detecting this condition.

OBJECT-TYPE

The radio number of the managed AP that last reported detecting this condition. Zero indicates no report available

OBJECT-TYPE

Indicates whether this test is configured to report rogues.

OBJECT-TYPE

Indicates whether this test reported the device as rogue.

OBJECT-TYPE

Indicates how long ago this test first detected the condition.

OBJECT-TYPE

Indicates how long ago this test last detected the condition.

OBJECT-TYPE

This table contains the AP de-authentication attack status.

OBJECT-TYPE

This table contains information about APs against which the Cluster Controller initiated a de-authentication attack.

OBJECT-TYPE

The AP de-authentication attack status table index.

OBJECT-TYPE

BSSID of the AP against which the attack is launched.

OBJECT-TYPE

Channel on which the rogue AP is operating.

OBJECT-TYPE

Time since attack started on this AP.

OBJECT-TYPE

Time since RF Scan report about this AP.

OBJECT-TYPE

This table contains status parameters of clients that are currently detected.

OBJECT-TYPE

Each entry in this table contains detected client status parameters.

OBJECT-TYPE

Detected client MAC address.

OBJECT-TYPE

This object indicates client's status. Authenticated- Client is Authenticated with the system and is not Rogue Detected- Client is detected, not Authenticated, not rogue, and is not found in the Known Clients Database. Known- Client is detected, but is not authenticated. Black-Listed- Client tried to associate with the system, but was rejected due to MAC authentication. Rogue- Client failed of the the enabled threat tests.

OBJECT-TYPE

This object indicates client's authentication status. Note that the Client Status can be Rogue, but the client can be Authenticated.

OBJECT-TYPE

This object indicates time since any event has been received for this client that updated the detected client database entry.

OBJECT-TYPE

This object indicates if any one of the threat detection tests have been triggered for this client. If the test is disabled the client won't be marked as Rogue, but administrator may still be interested in investigating why the threat triggered.

OBJECT-TYPE

This object indicates whether threat mitigation has been done for this client.

OBJECT-TYPE

Nickname from the Known Client Database. If client is not in the database then the nickname is blank.

OBJECT-TYPE

Indicates the time the detected client entry was created.

OBJECT-TYPE

this object indicates channel number in which the client is dtected

OBJECT-TYPE

If the client is authenticated with the managed AP then this object indicates Received Signal Strength(RSSI) value reported by the AP with which the client is authenticated.

OBJECT-TYPE

This object indicates the last signal strength(in dBm) reported by the managed AP with which the client is authenticated.

OBJECT-TYPE

This object indicates the last channel noise(in dBm) reported by the managed AP with which the client is authenticated.

OBJECT-TYPE

This object indicates the number of probe requests recorded so far during the probe collection interval.

OBJECT-TYPE

This object indicates how much time is left before the probe collection interval is done and the controller decides whether the client is a threat.

OBJECT-TYPE

This object indicates the largest number of probes that the controller detected during the collection interval.

OBJECT-TYPE

This object indicates the number of 802.11 authentication messages recorded so far during the auth collection interval.

OBJECT-TYPE

This object indicates how much time is left before the authentication collection interval is done and the controller decides whether the client is a threat.

OBJECT-TYPE

This object indicates the largest number of authentications that the controller detected during the collection interval.

OBJECT-TYPE

This object indicates the number of 802.11 de-authentication messages recorded so far during the de-auth collection interval.

OBJECT-TYPE

This object indicates how much time is left before the de-authentication collection interval is done and the controller decides whether the client is a threat.

OBJECT-TYPE

This object indicates the largest number of de-authentication messages that the controller detected during the collection interval.

OBJECT-TYPE

This object indicates the number of 802.1X Authentication failures detected for this client.

OBJECT-TYPE

This object indicates the number of probes detected in the last RF Scan.

OBJECT-TYPE

This object indicates the number of probes to broadcast BSSID in the last RF Scan.

OBJECT-TYPE

This object indicates the number of probes to broadcast SSID in the last RF Scan.

OBJECT-TYPE

This object indicates the number of probes to specific BSSID in the last RF Scan.

OBJECT-TYPE

This object indicates the number of probes to specific SSID in the last RF Scan.

OBJECT-TYPE

This object indicates the last non-broadcast BSSID detected in the RF Scan.

OBJECT-TYPE

This object indicates the last non-broadcast SSID detected in the RF Scan.

OBJECT-TYPE

This object indicates the time since the controller sent the last threat mitigation message to this client.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge the detected client entry except entries for authenticated clients. Read on this object will always return disable.

OBJECT-TYPE

This is a command that allows the administrator to clear the rogue status for the entry in the Detected clients database

OBJECT-TYPE

Device manufacturer information for this Detected client.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge all the detected clients entries except entries for authenticated clients. Read on this object will always return disable.

OBJECT-TYPE

This is a command that allows the administrator to clear the rogue status for all entries in the Detected clients database

OBJECT-TYPE

This table contains rogue classification test results for clients.

OBJECT-TYPE

Each entry in this table contains rogue classification test results for a client.

OBJECT-TYPE

The MAC address of the detected client.

OBJECT-TYPE

The rogue classification test id.

OBJECT-TYPE

The rogue classification test identifier.

OBJECT-TYPE

Indicates whether this test detected the condition that it is designed to detect.

OBJECT-TYPE

The MAC address of the managed AP that last reported detecting this condition.

OBJECT-TYPE

The radio number of the managed AP that last reported detecting this condition. Zero indicates no report available

OBJECT-TYPE

Indicates whether this test is configured to report rogues.

OBJECT-TYPE

Indicates whether this test reported the device as rogue.

OBJECT-TYPE

Indicates how long ago this test first detected the condition.

OBJECT-TYPE

Indicates how long ago this test last detected the condition.

OBJECT-TYPE

This table contains triangulation data to help the administrator determine which three managed non-sentry APs are detecting the client along with the signal strength and the time stamp.

OBJECT-TYPE

Each entry in this table contains triangulation information for the Detected Client entry.

OBJECT-TYPE

The MAC address of the Detected Client.

OBJECT-TYPE

Index of the non sentry triangulation entry.

OBJECT-TYPE

The MAC address of the detecting AP.

OBJECT-TYPE

The radio of the detecting AP.

OBJECT-TYPE

Received signal strength indicator in percent (0 to 100%).

OBJECT-TYPE

Received signal strength in dBm (-127 to 127).

OBJECT-TYPE

Noise reported on the channel by the AP in dBm (-127 to 127).

OBJECT-TYPE

Indicates the time since this device was most recently detected by the detecting AP.

OBJECT-TYPE

This table contains triangulation data to help the administrator determine which three managed sentry APs are detecting the client along with the signal strength and the time stamp.

OBJECT-TYPE

Each entry in this table contains triangulation information for the Detected Client entry.

OBJECT-TYPE

The MAC address of the detected client.

OBJECT-TYPE

Index of the sentry triangulation entry.

OBJECT-TYPE

The MAC address of the AP detecting the client.

OBJECT-TYPE

The radio of the AP detecting the client.

OBJECT-TYPE

Received signal strength indicator in percent (0 to 100%).

OBJECT-TYPE

Received signal strength in dBm (-127 to 127).

OBJECT-TYPE

Noise reported on the channel by the AP in dBm (-127 to 127).

OBJECT-TYPE

Indicates time since this device was most recently detected by the detecting AP.

OBJECT-TYPE

This table contains pre-authentication history entries for detected clients.

OBJECT-TYPE

Each entry in this table contains details of pre-authentication events occured for the detected client.

OBJECT-TYPE

The MAC address of the detected client.

OBJECT-TYPE

Numeric identifier for the preAuthentication entry.

OBJECT-TYPE

The Ethernet address of the AP with which client has pre-authenticated.

OBJECT-TYPE

The radio number of this radio in the AP with which client has pre-authenticated.

OBJECT-TYPE

The MAC address of the VAP to which client has roamed.

OBJECT-TYPE

This object indicates the SSID used by the VAP.

OBJECT-TYPE

Indicates time since this history event occured.

OBJECT-TYPE

Designates the pre-authentication operational status for this detected client.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge all the pre-authentication history entries for all the detected clients. Read on this object will always return disable.

OBJECT-TYPE

This table contains roam history entries for detected clients.

OBJECT-TYPE

Each entry in this table contains details of roam events occured for the detected client.

OBJECT-TYPE

The MAC address of the detected client.

OBJECT-TYPE

Numeric identifier for the Roam entry.

OBJECT-TYPE

The Ethernet address of the AP to which client has roamed.

OBJECT-TYPE

The radio number of this radio in the AP with which client has roamed.

OBJECT-TYPE

The MAC address of the VAP to which client has roamed.

OBJECT-TYPE

This object indicates the SSID used by the VAP.

OBJECT-TYPE

Indicates time since this roam history event occured.

OBJECT-TYPE

Designates the roaming operational status for this detected client.

OBJECT-TYPE

This is an action object. Setting this object to enable will purge all the roaming history entries for all the detected clients. Read on this object will always return disable.

OBJECT-IDENTITY

OBJECT-TYPE

Flag to enable/disable SNMP traps for: WS Enabled, WS Disabled, WS Managed AP Database Full, WS Managed AP - AP Neighbor List Full, WS Managed AP - Client Neighbor List Full, WS - AP Failure List Full, RF Scan AP List Full, Client Association Database Full, Client Failure List Full.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: Peer WS Discovered, Peer WS Failed, Peer WS Unknown Protocol Discovered.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: WS Managed AP Discovered, WS Managed AP Failed, WS Managed AP Unknown Protocol Discovered.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: WS AP Association Failure, WS AP Authentication Failure.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: RF Scan Rogue AP Detected.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: RF Scan New AP Detected, RF Scan New Client Detected. RF Scan Ad hoc Client Detected.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: Client Association Detected, Client Disassociation Detected, Client Roam Detected.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: This controller is Cluster Controller, Rogues are Present in the Network, RF Scan Rogue AP Detected.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: TSPEC Client ACM Bandwidth Exceeded, TSPEC Client Traffic Unauthorized.

OBJECT-TYPE

Flag to enable/disable SNMP traps for: Client Association Failure, Client Authentication Failure.

OBJECT-IDENTITY

OBJECT-TYPE

The version number of this MIB module

OBJECT-IDENTITY

OBJECT-TYPE

This table defines supported features for APs of specific hardware type. This is a read only table and is used by application to validate parameters

OBJECT-TYPE

Each entry provides access point hardware type details for each AP hardware type supported by the WS.

OBJECT-TYPE

Numeric identifier for the AP hardware type.

OBJECT-TYPE

Descriptive name of the AP hardware type.

OBJECT-TYPE

Number of radios supported by this hardware type AP.

OBJECT-TYPE

Image type for code download for this hardware type AP.

OBJECT-TYPE

Dual boot support for this hardware type AP.

OBJECT-TYPE

The AP harware radio capability table contain only those parameters that vary from one AP hardware type to another. Parameters that don't vary depending on AP type or radio type are not included in the table.This read-only table provides the user to view configurable parameters for the APs of specific hardware type through the profile.

OBJECT-TYPE

Each entry provides radio capability details for each AP hardware type supported by the WS.

OBJECT-TYPE

The radio number of this radio in the AP.

OBJECT-TYPE

The device id for this radio in the AP.

OBJECT-TYPE

Text description of this radio type.