AT-LOADER-MIB
- Registered at
- 1.3.6.1.4.1.207.8.4.4.4.48
- Last updated
- 2007-02-07 10:10
- Organization
- Allied Telesis, Inc
- Revisions
- 2007-02-07 10:10, 2006-06-28 12:22
- Namespace
- allied
- Source file
AT-LOADER-MIB- Digest
sha256:3481343384b7f08bc3b3f7f25a81df7624d02acbabf1d3fa6c9b9b823593d50c
Description
To handle upload, object loadStatus is upgraded, as well as the description for objects loadServer and loadFilename.
Contact
http://www.alliedtelesis.com
Imports
| From | Symbols |
|---|---|
| AT-SMI-MIB | DisplayStringUnsized, modules |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
AT-LOADER-MIB AT-SMI-MIB IANAifType-MIB IF-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| loadTable OBJECT-TYPE The table of load parameters, dynamic and static. | 1.3.6.1.4.1.207.8.4.4.4.48.1 | not-accessible | current | |
| loadEntry OBJECT-TYPE A single entry of load parameters. This contains the parameters required to perform a load from the router. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1 | not-accessible | current | |
| loadIndex OBJECT-TYPE There are two sets of load information, dynamic and static. The dynamic information is used once, then cleared. The static information is used whenever the dynamic information is not available. The dynamic information is also used to indicate the current load parameters when a load is in progress. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1.1 | INTEGER {static(1), dynamic(2)} | read-write | current |
| loadServer OBJECT-TYPE The IP address from which load will load or upload. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1.2 | IpAddress | read-write | current |
| loadDestination OBJECT-TYPE The destination of the file loaded, either flash or nvs memory, or undefined. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1.3 | INTEGER {undefined(1), nvs(2), flash(3)} | read-write | current |
| loadFilename OBJECT-TYPE The file name of the file being loaded or uploaded. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1.4 | DisplayString | read-write | current |
| loadDelay OBJECT-TYPE A delay in seconds between the initiation of the load and the start of the load. This allows for time to set up TFTP servers in cases where the terminal and TFTP server are using the same piece of equipment but will not work simultaneously. | 1.3.6.1.4.1.207.8.4.4.4.48.1.1.5 | INTEGER | read-write | current |
| loadStatus OBJECT-TYPE Status and action object for the load module. The values 1 to 5 are read-only values and reflect the state of the load module. Values 4 and 5 (complete and reset) are 'read-once', that is, if their values are read, either by SNMP or by manager console command, then they will be changed back to idle(1). The action values (6,7,8) cause a start and stop of the load/upload process respectively. Starting the load/upload can only occur if this field has the values 1, 4, or 5. Stopping the load can only occur is this field has the values 2 or 3. Reading the value of the loadStatus after one of actionstart or actionstop has been set will give one of the values 1 to 5. Note: A single exception to the above rules is that if the value of loadStatus is idle(1), then a write of 1 to this variable will succeed without generating an error. This exception is to allow certain SNMP test suites to test this variable without throwing up errors. | 1.3.6.1.4.1.207.8.4.4.4.48.2 | INTEGER {idle(1), wait(2), loading(3), complete(4), reset(5), actionload(6), actionstop(7), actionupload(8)} | read-write | current |