ARUBAWIRED-LOOPPROTECT-MIB
- Registered at
- 1.3.6.1.4.1.47196.4.1.1.3.1
- Last updated
- 2017-11-02 00:00
- Organization
- HPE/Aruba Networking Division
- Revisions
- 2017-11-02 00:00
- Namespace
- arubaos
- Source file
ARUBAWIRED-LOOPPROTECT-MIB- Digest
sha256:fb1f98872b860af9c5ec5379e6154d0460b46a88e09309da33a99620d47c6307
Description
This MIB module contains HP proprietary extensions to the standard Loop Protect MIBs.
Contact
Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747
Imports
| From | Symbols |
|---|---|
| ARUBAWIRED-NETWORKING-OID | wndFeatures |
| BRIDGE-MIB | dot1dBasePortEntry |
| IF-MIB | InterfaceIndex, ifIndex |
| Q-BRIDGE-MIB | VlanId, VlanIndex, dot1qVlanStaticEntry |
| SMON-MIB | portCopyEntry |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
ARUBAWIRED-LOOPPROTECT-MIB ARUBAWIRED-NETWORKING-OID BRIDGE-MIB IANAifType-MIB IF-MIB P-BRIDGE-MIB Q-BRIDGE-MIB RFC1158-MIB RFC1271-MIB RMON-MIB RMON2-MIB SMON-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC TOKEN-RING-RMON-MIB
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ConfigStatus TEXTUAL-CONVENTION Used to indicate the configuration status for a group of objects. 'active' means that the values of the related objects are currently in use by the device. 'notInService' indicates that the objects have been reconfigured in such a way that the values cannot take effect until after the next reboot of the device. 'notReady' indicates that the objects are not consistent with each other. | current | |||
| LoopProtectReceiverAction TEXTUAL-CONVENTION This TC describes the actions a port that receives a Loop Protection Protocol packet can take. The disableTx(1) enumeration indicates that the sender of the Loop Protect packet will be disabled. The noDisable(2) enumeration indicates that no port is to be disabled. The disableTxRx(3) enumeration indicates that the senders and receivers of the Loop Protect packets will be disabled. | current | |||
| VidList TEXTUAL-CONVENTION Each octet within this value specifies a set of eight VlanIIndex (VID), with the first octet specifying VIDs 1 through 8, the second octet specifying VIDs 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered VID, and the least significant bit represents the highest numbered VID. Thus, each VID is represented by a single bit within the value of this object. If that bit has a value of 1 then that VID is included in the set of VIDs; the VID is not included if its bit has a value of 0. This list represents the entire range of VlanIndex values defined in the scope of IEEE 802.1Q. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| arubaWiredLoopProtectObjects OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1 | |||
| arubaWiredLoopProtect OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5 | |||
| arubaWiredLoopProtectNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.0 | |||
| arubaWiredLoopProtectBase OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1 | |||
| arubaWiredLoopProtectInterval OBJECT-TYPE The interval in seconds at which Loop Protection packets are transmitted. The default value is 5 seconds. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1.1 | Integer32 (1..10) | read-write | current |
| arubaWiredLoopProtectTrapLoopDetectEnable OBJECT-TYPE Indicates whether notifications should be sent when a loop is detected on a port. By default this object will have a value of false(2). | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1.2 | TruthValue | read-write | current |
| arubaWiredLoopProtectEnableTimer OBJECT-TYPE The time in seconds to wait before re-enabling a port disabled by Loop Protection. When a port is disabled by Loop Protection, a re-enable timer for the port is initialized. If the re-enable timer value is specified as zero seconds the port remains disabled, else the port is re-enabled after the specified time. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1.3 | Integer32 (0..2147483647) | read-write | current |
| arubaWiredLoopProtectMode OBJECT-TYPE This object is used to configure the operational mode of Loop Protection feature. The Loop Protection feature can be configured to operate in port mode or VLAN mode. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1.4 | INTEGER {port(1), vlan(2)} | read-write | current |
| arubaWiredLoopProtectVIDList OBJECT-TYPE A list of VLANs on which Loop Protection is enabled. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.1.5 | VidList | read-write | current |
| arubaWiredLoopProtectPort OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2 | |||
| arubaWiredLoopProtectPortTable OBJECT-TYPE Per-interface configuration for Loop Protection. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1 | not-accessible | current | |
| arubaWiredLoopProtectPortEntry OBJECT-TYPE Loop Protection configuration information for a single port. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1 | not-accessible | current | |
| arubaWiredLoopProtectPortInterfaceIndex OBJECT-TYPE The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.1 | InterfaceIndex | not-accessible | current |
| arubaWiredLoopProtectPortEnable OBJECT-TYPE This object indicates whether the Loop Protection is enabled on a port. The default value is FALSE | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.2 | TruthValue | read-write | current |
| arubaWiredLoopProtectPortLoopDetected OBJECT-TYPE This object will be set to TRUE when a loop is detected on the port. The value of this object will be reset to FALSE when the port's arubaWiredLoopProtectPortEnable is set to FALSE. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.3 | TruthValue | read-only | current |
| arubaWiredLoopProtectPortLastLoopTime OBJECT-TYPE The value of sysUpTime when a loop was last detected on this port. A value of 0 means that the timestamp has not been set. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.4 | TimeStamp | read-only | current |
| arubaWiredLoopProtectPortLoopCount OBJECT-TYPE This object provides the number of loops detected on a Loop Protection enabled port. The value of this object is set to zero when Loop Protection is disabled on a port. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.5 | Counter32 | read-only | current |
| arubaWiredLoopProtectPortReceiverAction OBJECT-TYPE Controls the action taken when a Loop Protection packet is received on this port. When set to 'disableTx' the port that transmitted the packet is disabled. When set to 'noDisable' the transmitting port is not disabled. When set to 'disableTxRx' the ports transmitting and receiving the packets are disabled. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.6 | LoopProtectReceiverAction | read-write | current |
| arubaWiredLoopProtectLoopDetectedVlan OBJECT-TYPE Refers to this object for the port on which loop is detected. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.7 | Integer32 (1..4096) | read-only | current |
| arubaWiredLoopProtectPortVlanList OBJECT-TYPE A list of VLANs for this interface in which Loop Protection is enabled. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.2.1.1.8 | VidList | read-write | current |
| arubaWiredLoopProtectConformance OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3 | |||
| arubaWiredLoopProtectGroups OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3.1 | |||
| arubaWiredLoopProtectCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| arubaWiredLoopProtectLoopDetectedNotification NOTIFICATION-TYPE A arubaWiredLoopProtectLoopDetectedNotification signifies that a loop is detected by the Loop Protection Protocol. Generation of this notification is controlled by arubaWiredLoopProtectTrapLoopDetectEnable. To prevent excessive notifications, this trap allows only one notifications every 30 seconds. Notifications that are missed due to this limitation are dropped and are not sent later. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.0.1 | current |
| arubaWiredLoopProtectVlanLoopDetectedNotification NOTIFICATION-TYPE A arubaWiredLoopProtectVlanLoopDetectedNotification signifies that a loop is detected by the Loop Protection feature while operating in VLAN mode. Generation of this notification is controlled by arubaWiredLoopProtectTrapLoopDetectEnable. To prevent excessive notifications, this trap allows only one notifications every 30 seconds. Notifications that are missed due to this limitation are dropped and are not sent later. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.0.2 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| arubaWiredLoopProtectBaseGroup OBJECT-GROUP A collection of objects providing basic instrumentation and control of the HP Loop protection entity. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3.1.4 | current |
| arubaWiredLoopProtectVLANGroup OBJECT-GROUP A collection of objects providing support for Loop Protect per VLAN feature. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3.1.10 | current |
| arubaWiredLoopProtectCompliance MODULE-COMPLIANCE The compliance statement for HP Switches with support for arubaWired loop protection objects. | 1.3.6.1.4.1.47196.4.1.1.3.1.1.5.3.2.5 | current |