MIBs Depot

ALVARION-DOT11-WLAN-MIB

Registered at
1.3.6.1.4.1.12394
Last updated
1907-08-14 11:46
Organization
Alvarion Ltd.
Revisions
1907-08-14 11:46
Namespace
alvarion
Source file
ALVARION-DOT11-WLAN-MIB
Digest
sha256:adcdb31acea484eb8f663e2658cb5983502c7b38b53e8b89c307d3fd6c01b176

Description

BreezeAccess VL, BreezeACCESS 4900 and BreezeNET-B

Contact

Alvarion Customer Service Postal: Alvarion Ltd. Barzel 21 Tel Aviv 69710 ISRAEL E-mail: CS_Coordinator@alvarion.com

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ALVARION-DOT11-WLAN-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
DisplayString
type
MacAddress
type

Objects

NameOIDSyntaxAccessStatus
alvarion
OBJECT-IDENTITY
1.3.6.1.4.1.12394
products
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1
brzaccVLSysInfo
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.1
brzaccVLUnitHwVersion
OBJECT-TYPE
Applicable to all units. Hardware platform version.
1.3.6.1.4.1.12394.1.1.1.1DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLRunningSoftwareVersion
OBJECT-TYPE
Applicable to all units. Running software version.
1.3.6.1.4.1.12394.1.1.1.2DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLRunningFrom
OBJECT-TYPE
Applicable to all units. The memory (main or shadow) from which the current version is running from.
1.3.6.1.4.1.12394.1.1.1.3INTEGER {mainVersion(1), shadowVersion(2)}read-onlycurrent
brzaccVLMainVersionNumber
OBJECT-TYPE
Applicable to all units. Main software version number.
1.3.6.1.4.1.12394.1.1.1.4DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLMainVersionFileName
OBJECT-TYPE
Applicable to all units. Main software version file name.
1.3.6.1.4.1.12394.1.1.1.5DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLShadowVersionNumber
OBJECT-TYPE
Applicable to all units. Shadow software version number.
1.3.6.1.4.1.12394.1.1.1.6DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLShadowVersionFileName
OBJECT-TYPE
Applicable to all units. Shadow software version file name.
1.3.6.1.4.1.12394.1.1.1.7DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLUnitMacAddress
OBJECT-TYPE
Applicable to all units. Unit hardware MAC address.
1.3.6.1.4.1.12394.1.1.1.8MacAddressread-onlycurrent
brzaccVLUnitType
OBJECT-TYPE
Applicable to all units. auBS (1) : AU-BS (modular access unit). auSA (2) : AU-SA (stand-alone access unit). su-6-1D (3) : SU-6-1D (subscriber unit supporting 6 Mbps) su-6-BD (4) : SU-6-BD (subscriber unit supporting 6 Mbps). su-24-BD (5) : SU-24-BD (subscriber unit supporting 24 Mbps). bu-B14 (6) : BU-B14 (BreezeNET Base Unit supporting 14 Mbps). bu-B28 (7) : BU-B28 (BreezeNET Base Unit supporting 28 Mbps). rb-B14 (8) : RB-B14 (BreezeNET Remote Bridge supporting 14 Mbps). rb-B28 (9) : RB-B28 (BreezeNET Remote Bridge supporting 28 Mbps). su-BD (10) : SU-BD (subscriber unit). su-54-BD(11) : SU-54-BD (subscriber unit supporting 54 Mbps). su-3-1D (12) : SU-3-1D (subscriber unit supporting 3 Mbps). su-3-4D (13) : SU-3-4D (subscriber unit supporting 3 Mbps). ausBS (14) : AUS-BS (modular access unit supporting maxim 8 or 25 (via licensing) subscribers and allowing association only with SU-3 or SU-6). ausSA (15) : AUS-SA (stand-alone access unit supporting maxim 8 or 25 (via licensing) subscribers and allowing association only with SU-3 or SU-6 ). auBS4900(16) : AU-BS-4900 (BreezeAccess 4900 modular access unit) auSA4900(17) : AU-SA-4900 (BreezeAccess 4900 stand alone access unit) suBD4900(18) : SU-BD-4900 (BreezeAccess 4900 subscriber unit) bu-B100 (19) : BU-B100 (BreezeNET Base Unit unlimited throughput) rb-B100 (20) : BU-B100 (BreezeNET Remote Bridge unlimited throughput) su-I (21) : SU-I au-E (22) : AU-E
1.3.6.1.4.1.12394.1.1.1.9INTEGER {auBS(1), auSA(2), su-6-1D(3), su-6-BD(4), su-24-BD(5), bu-B14(6), bu-B28(7), rb-B14(8), rb-B28(9), su-BD(10), su-54-BD(11), su-3-1D(12), su-3-4D(13), ausBS(14), ausSA(15), auBS4900(16), auSA4900(17), su4900(18), bu-B100(19), rb-B100(20), su-I(21), au-E(22)}read-onlycurrent
brzaccVLAssociatedAU
OBJECT-TYPE
Applicable to SU/RB only. Associated AU/BU MAC address.
1.3.6.1.4.1.12394.1.1.1.10MacAddressread-onlycurrent
brzaccVLNumOfAssociationsSinceLastReset
OBJECT-TYPE
Applicable to all units. The number of associations since last reset, including duplicate associations (re-associations).
1.3.6.1.4.1.12394.1.1.1.11INTEGERread-onlycurrent
brzaccVLCurrentNumOfAssociations
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. The number of SUs currently associated with the AU. BreezeNET-B products return 65535.
1.3.6.1.4.1.12394.1.1.1.13INTEGERread-onlycurrent
brzaccVLUnitBootVersion
OBJECT-TYPE
Applicable to all units. Boot version.
1.3.6.1.4.1.12394.1.1.1.14DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLRadioBand
OBJECT-TYPE
Applicable to all units. The unit's radio band.
1.3.6.1.4.1.12394.1.1.1.15INTEGER {band-5-8GHz(1), band-5-4GHz(2), band-4-9GHz(3), band-5-2GHz(4), band-2-4GHz(5), band-5-3GHz(6), band-4-9GHzJapan(7)}read-onlycurrent
brzaccVLCurrentEthernetPortState
OBJECT-TYPE
Applicable to all units. The current Ethernet port state.
1.3.6.1.4.1.12394.1.1.1.16INTEGER {halfDuplexAnd10Mbps(1), fullDuplexAnd10Mbps(2), halfDuplexAnd100Mbps(3), fullDuplexAnd100Mbps(4), linkDown(5)}read-onlycurrent
brzaccVLTimeSinceLastReset
OBJECT-TYPE
Applicable to all units. The elapsed time since last reset.
1.3.6.1.4.1.12394.1.1.1.17DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLCountryDependentParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.1.18
brzaccVLCountryCode
OBJECT-TYPE
Applicable to all units. The country code and country name or country group name that is supported by the unit.
1.3.6.1.4.1.12394.1.1.1.18.1DisplayString (SIZE(0..32))read-onlycurrent
brzaccVLCountryDependentParamsTable
OBJECT-TYPE
Applicable to all units. A table of country dependent parameters.
1.3.6.1.4.1.12394.1.1.1.18.2not-accessiblecurrent
brzaccVLCountryDependentParameterEntry
OBJECT-TYPE
Applicable to all units. An entry in the Country Dependent Parameters table.
1.3.6.1.4.1.12394.1.1.1.18.2.1not-accessiblecurrent
brzaccVLCountryDependentParameterTableIdx
OBJECT-TYPE
Applicable to all units. The sub-band ID of the entry in the Country Dependent Parameters table. Serves also as index for the table entry.
1.3.6.1.4.1.12394.1.1.1.18.2.1.1INTEGER (1..5)read-onlycurrent
brzaccVLCountryDependentParameterFrequencies
OBJECT-TYPE
Applicable to all units. The frequencies included in the applicable sub-band entry.
1.3.6.1.4.1.12394.1.1.1.18.2.1.2DisplayStringread-onlycurrent
brzaccVLAllowedBandwidth
OBJECT-TYPE
Applicable to all units. The bandwidth when using the applicable the sub-band.
1.3.6.1.4.1.12394.1.1.1.18.2.1.3INTEGERread-onlycurrent
brzaccVLRegulationMaxTxPowerAtAntennaPort
OBJECT-TYPE
Applicable to all units. The maximum allowed Tx power when using the applicable sub-band. A RegulationMaxTxPowerAtAntennaPort of 255, means no limit
1.3.6.1.4.1.12394.1.1.1.18.2.1.4INTEGERread-onlycurrent
brzaccVLRegulationMaxEIRP
OBJECT-TYPE
Applicable to all units. The maximum Tx EIRP when using the applicable sub-band. A Regulation Max EIRP of 0, means no limit.
1.3.6.1.4.1.12394.1.1.1.18.2.1.5INTEGERread-onlycurrent
brzaccVLMinModulationLevel
OBJECT-TYPE
Applicable to all units. The minimum supported modulation level.
1.3.6.1.4.1.12394.1.1.1.18.2.1.6INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-onlycurrent
brzaccVLMaxModulationLevel
OBJECT-TYPE
Applicable to all units. The maximum supported modulation level.
1.3.6.1.4.1.12394.1.1.1.18.2.1.7INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-onlycurrent
brzaccVLBurstModeSupport
OBJECT-TYPE
Applicable to all units. The supported Burst Mode Option.
1.3.6.1.4.1.12394.1.1.1.18.2.1.8INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLMaximumBurstDuration
OBJECT-TYPE
Applicable to all units. Applicable only if Burst Mode Option is supported. The maximum supported burst duration.
1.3.6.1.4.1.12394.1.1.1.18.2.1.9INTEGERread-onlycurrent
brzaccVLDfsSupport
OBJECT-TYPE
Applicable to AU/BU only. The supported Dfs Option.
1.3.6.1.4.1.12394.1.1.1.18.2.1.10INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLMinimumHwRevision
OBJECT-TYPE
Applicable to all units. The Minimum HW Revision needed to support the country code.
1.3.6.1.4.1.12394.1.1.1.18.2.1.11INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
brzaccVLAuthenticationEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported Authentication Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.3INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLDataEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported Data Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.4INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLAESEncryptionSupport
OBJECT-TYPE
Applicable to all units. The supported AES Encryption Option.
1.3.6.1.4.1.12394.1.1.1.18.5INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLAntennaGainChange
OBJECT-TYPE
Applicable to all units. Indicates whether the Antenna Gain parameter is changeable or fixed.
1.3.6.1.4.1.12394.1.1.1.19INTEGER {supported(1), notSupported(2)}read-onlycurrent
brzaccVLAteTestResults
OBJECT-TYPE
Applicable to all units. Results of ATE Test
1.3.6.1.4.1.12394.1.1.1.20INTEGER {none(0), pass(1), fail(2)}read-onlycurrent
brzaccVLSerialNumber
OBJECT-TYPE
Applicable to all units. Serial Number of the unit
1.3.6.1.4.1.12394.1.1.1.21DisplayString (SIZE(0..35))read-onlycurrent
brzaccVLUnitControl
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2
brzaccVLResetUnit
OBJECT-TYPE
Applicable to all units. Resets the unit and applies new parameter values.
1.3.6.1.4.1.12394.1.1.2.1INTEGER {cancel(1), resetSystemNow(2)}read-writecurrent
brzaccVLSetDefaults
OBJECT-TYPE
Applicable to all units. Sets unit configuration to Defaults values after the next reset. noDefaultSettingRequested : Read-Only Option, no Default setting was Issued. completeFactory : All parameters revert to Factory Defaults values. partialFactory : All parameters revert to Factory Defaults values, except the parameters required for maintaining wireless connectivity. completeOperator: All parameters revert to Operator Defaults values. partialOperator : All parameters revert to Operator Defaults values, except the parameters required for maintaining wireless connectivity. cancelCurrentPendingRequest : Default Setting request is cancelled.
1.3.6.1.4.1.12394.1.1.2.2INTEGER {noDefaultSettingRequested(0), completeFactory(1), partialFactory(2), completeOperator(3), partialOperator(4), cancelCurrentPendingRequest(5)}read-writecurrent
brzaccVLUnitName
OBJECT-TYPE
Applicable to all units. The unit name. A string of up to 32 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.3DisplayString (SIZE(0..32))read-writecurrent
brzaccVLFlashMemoryControl
OBJECT-TYPE
Applicable to all units. resetAndBootFromShadowVersion : Activates the backup version. useRunningVersionAfterReset : The currently active version will become the main version and will be activated after next reset.
1.3.6.1.4.1.12394.1.1.2.4INTEGER {resetAndBootFromShadowVersion(1), useRunningVersionAfterReset(2), cancel(3)}read-writecurrent
brzaccVLTelnetLogoutTimer
OBJECT-TYPE
Applicable to all units. Time-out of management via Telnet program. Automatic exit if the program is inactive for the defined time. Range: 1 to 999 (minutes).
1.3.6.1.4.1.12394.1.1.2.5INTEGERread-writecurrent
brzaccVLSaveCurrentConfigurationAsOperatorDefaults
OBJECT-TYPE
Applicable to all units. Saves the current configuration as Operator Defaults. Cannot be executed after requesting set defaults and the unit was not reset.
1.3.6.1.4.1.12394.1.1.2.6INTEGER {saveAsDefaults(1), cancel(2)}read-writecurrent
brzaccVLExitTelnet
OBJECT-TYPE
Applicable to all units. Exit the management via Telnet program.
1.3.6.1.4.1.12394.1.1.2.7INTEGER {cancelOperation(1), exit(2)}read-writecurrent
brzaccVLUnitPasswords
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.8
brzaccVLReadOnlyPassword
OBJECT-TYPE
Applicable to all units. The User (read only) password. This is also the Read Community String. Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.1DisplayString (SIZE(1..8))read-writecurrent
brzaccVLInstallerPassword
OBJECT-TYPE
Applicable to all units. The Installer password. Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.2DisplayString (SIZE(1..8))read-writecurrent
brzaccVLAdminPassword
OBJECT-TYPE
Applicable to all units. The Administrator password. Accessible only with SNMP Write Community String (administrator password). Up to 8 printable ASCII characters.
1.3.6.1.4.1.12394.1.1.2.8.3DisplayString (SIZE(1..8))read-writecurrent
brzaccVLEthernetNegotiationMode
OBJECT-TYPE
Applicable to all units. The speed/duplex mode of the Ethernet port.
1.3.6.1.4.1.12394.1.1.2.9INTEGER {force10MbpsAndHalfDuplex(1), force10MbpsAndFullDuplex(2), force100MbpsAndHalfDuplex(3), force100MbpsAndFullDuplex(4), autoNegotiationMode(5)}read-writecurrent
brzaccVLFTPParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10
brzaccVLFTPServerParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.1
brzaccVLFTPServerUserName
OBJECT-TYPE
Applicable to all units. The user name to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
1.3.6.1.4.1.12394.1.1.2.10.1.1DisplayString (SIZE(0..18))read-writecurrent
brzaccVLFTPServerPassword
OBJECT-TYPE
Applicable to all units. The password to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
1.3.6.1.4.1.12394.1.1.2.10.1.2DisplayString (SIZE(0..18))read-writecurrent
brzaccVLFTPClientIPAddress
OBJECT-TYPE
Applicable to all units. For SW version higher than 4.0 this is read-only. The IP address of the FTP stack in the unit.
1.3.6.1.4.1.12394.1.1.2.10.1.3IpAddressread-writecurrent
brzaccVLFTPServerIpAddress
OBJECT-TYPE
Applicable to all units. The IP address of the FTP server.
1.3.6.1.4.1.12394.1.1.2.10.1.4IpAddressread-writecurrent
brzaccVLFTPClientMask
OBJECT-TYPE
Applicable to all units. The Mask of the FTP stack in the unit.
1.3.6.1.4.1.12394.1.1.2.10.1.5IpAddressread-writecurrent
brzaccVLFTPGatewayIpAddress
OBJECT-TYPE
Applicable to all units. The FTP Gateway address
1.3.6.1.4.1.12394.1.1.2.10.1.6IpAddressread-writecurrent
brzaccVLFTPSwDownload
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.2
brzaccVLFTPSwFileName
OBJECT-TYPE
Applicable to all units. The name of the SW file to be downloaded.
1.3.6.1.4.1.12394.1.1.2.10.2.1DisplayString (SIZE(1..20))read-writecurrent
brzaccVLFTPSwSourceDir
OBJECT-TYPE
Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
1.3.6.1.4.1.12394.1.1.2.10.2.2DisplayString (SIZE(0..80))read-writecurrent
brzaccVLFTPDownloadSwFile
OBJECT-TYPE
Applicable to all units. Execution of the SW download operation
1.3.6.1.4.1.12394.1.1.2.10.2.3INTEGER {downloadFile(1), cancel(2)}read-writecurrent
brzaccVLConfigurationFileLoading
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.3
brzaccVLConfigurationFileName
OBJECT-TYPE
Applicable to all units. The name of the configuration file to be downloaded/uploaded.
1.3.6.1.4.1.12394.1.1.2.10.3.1DisplayString (SIZE(1..20))read-writecurrent
brzaccVLOperatorDefaultsFileName
OBJECT-TYPE
Applicable to all units. The name of the Operator Defaults file to be downloaded/uploaded
1.3.6.1.4.1.12394.1.1.2.10.3.2DisplayString (SIZE(1..20))read-writecurrent
brzaccVLFTPConfigurationFileSourceDir
OBJECT-TYPE
Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
1.3.6.1.4.1.12394.1.1.2.10.3.3DisplayString (SIZE(0..80))read-writecurrent
brzaccVLExecuteFTPConfigurationFileLoading
OBJECT-TYPE
Applicable to all units. Execution of the file download/upload operation.
1.3.6.1.4.1.12394.1.1.2.10.3.4INTEGER {executeFTPGetConfigurationFile(1), executeFTPPutConfigurationFile(2), executeFTPGetOperatorDefaults(3), executeFTPPutOperatorDefaults(4), cancel(5)}read-writecurrent
brzaccVLEventLogFileUploading
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.10.4
brzaccVLEventLogFileName
OBJECT-TYPE
Applicable to all units. The name of the Event Log file to be uploaded.
1.3.6.1.4.1.12394.1.1.2.10.4.1DisplayString (SIZE(1..20))read-writecurrent
brzaccVLEventLogDestinationDir
OBJECT-TYPE
Applicable to all units. The destination directory of the event log file. Up to 80 printable ASCII characters. Use dot (.) To clear field.
1.3.6.1.4.1.12394.1.1.2.10.4.2DisplayString (SIZE(0..80))read-writecurrent
brzaccVLUploadEventLogFile
OBJECT-TYPE
Applicable to all units. Execution of the event log upload operation.
1.3.6.1.4.1.12394.1.1.2.10.4.3INTEGER {uploadFile(1), cancel(2)}read-writecurrent
brzaccVLLoadingStatus
OBJECT-TYPE
Applicable to all units. The status of the last loading operation.
1.3.6.1.4.1.12394.1.1.2.11INTEGER {inProcess(1), successful(2), failed(3)}read-onlycurrent
brzaccVLEventLogFileParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.12
brzaccVLEventLogPolicy
OBJECT-TYPE
Applicable to all units. The lowest level event to be registered in the event log.
1.3.6.1.4.1.12394.1.1.2.12.1INTEGER {message(1), warning(2), error(3), fatal(4), logNone(5)}read-writecurrent
brzaccVLEraseEventLog
OBJECT-TYPE
Applicable to all units. Erase the event log.
1.3.6.1.4.1.12394.1.1.2.12.2INTEGER {eraseEventLog(1), cancel(2)}read-writecurrent
brzaccVLSystemLocation
OBJECT-TYPE
Applicable to all units. The unit location.
1.3.6.1.4.1.12394.1.1.2.13DisplayString (SIZE(0..34))read-writecurrent
brzaccVLFeatureUpgrade
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.2.14
brzaccVLFeatureUpgradeManually
OBJECT-TYPE
Applicable to all units. Upgrade unit to support new feature. Enter your license number (32 to 64 hex digits).
1.3.6.1.4.1.12394.1.1.2.14.1DisplayString (SIZE(32..64))read-writecurrent
brzaccVLChangeUnitType
OBJECT-TYPE
Applicable RB/BU only. Change the unit type between BU and RB.
1.3.6.1.4.1.12394.1.1.2.15INTEGER {bu(1), rb(2), cancel(3)}read-writecurrent
brzaccLighteAPWorkingMode
OBJECT-TYPE
Applicable to AU only. Change unit running mode: 0 - VL mode 1 - Mixed cell mode
1.3.6.1.4.1.12394.1.1.2.16INTEGERread-writecurrent
brzaccVLNwMngParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.3
brzaccVLAccessToNwMng
OBJECT-TYPE
Applicable to all units. The port to be used for remote management.
1.3.6.1.4.1.12394.1.1.3.1INTEGER {fromWirelessOnly(1), fromEthernetOnly(2), fromBothWirelessAndEthernet(3), na(255)}read-writecurrent
brzaccVLNwMngFilter
OBJECT-TYPE
Applicable to all units. Disables or enable on one of the ports, or on both ports, IP address based filtering of management messages (e.g. SNMP , Telnet , TFTP , DHCP).
1.3.6.1.4.1.12394.1.1.3.2INTEGER {disable(1), activateOnEthernetPort(2), activateOnWirelessPort(3), activateOnBothWirelessAndEthernet(4), na(255)}read-writecurrent
mngIpFilterTable
OBJECT-TYPE
Applicable to all units. A Management IP Filter Table of up to 3 IP addresses of devices that are authorized to access the unit for management purposes.
1.3.6.1.4.1.12394.1.1.3.3not-accessiblecurrent
mngIpFilterEntry
OBJECT-TYPE
Applicable to all units. A Management IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.3.3.1not-accessiblecurrent
brzaccVLNwMngIpAddress
OBJECT-TYPE
Applicable to all units. An IP address in the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.3.1.1IpAddressread-writecurrent
brzaccVLNwMngIpTableIdx
OBJECT-TYPE
Applicable to all units. A table index for an entry in the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.3.1.2INTEGER (1..10)read-onlycurrent
brzaccVLDeleteOneNwIpAddr
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.4INTEGER (0 | 1..10 | 255)read-writecurrent
brzaccVLDeleteAllNwIpAddrs
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management IP Filter Table.
1.3.6.1.4.1.12394.1.1.3.5INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
brzaccVLAccessToNwTrap
OBJECT-TYPE
Applicable to all units. Enables or disables sending of traps.
1.3.6.1.4.1.12394.1.1.3.6INTEGER {disable(1), enable(2)}read-writecurrent
mngTrapTable
OBJECT-TYPE
Applicable to all units. A Management Trap Table of up to 10 IP addresses of stations to send traps to.
1.3.6.1.4.1.12394.1.1.3.7not-accessiblecurrent
mngTrapEntry
OBJECT-TYPE
Applicable to all units. A Management Trap Table entry.
1.3.6.1.4.1.12394.1.1.3.7.1not-accessiblecurrent
brzaccVLNwMngTrapCommunity
OBJECT-TYPE
Applicable to all units. The trap community associated with the applicable entry in the Management Trap Table. Up to 14 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.3.7.1.1DisplayString (SIZE(0..14))read-writecurrent
brzaccVLNwMngTrapAddress
OBJECT-TYPE
Applicable to all units. An IP address in the Management Trap Table entry.
1.3.6.1.4.1.12394.1.1.3.7.1.2IpAddressread-writecurrent
brzaccVLNwTrapTableIdx
OBJECT-TYPE
Applicable to all units. Tables Index for an entry in the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.7.1.3INTEGER (1..10)read-onlycurrent
brzaccVLDeleteOneTrapAddr
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.8INTEGER (0 | 1..10 | 255)read-writecurrent
brzaccVLDeleteAllTrapAddrs
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management Trap Table.
1.3.6.1.4.1.12394.1.1.3.9INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
brzaccVLMngIpRangesTable
OBJECT-TYPE
Applicable to all units. Table of Management IP Address Ranges
1.3.6.1.4.1.12394.1.1.3.10not-accessiblecurrent
brzaccVLMngIpRangeEntry
OBJECT-TYPE
Applicable to all units. A Management IP Address Ranges Table entry
1.3.6.1.4.1.12394.1.1.3.10.1not-accessiblecurrent
brzaccVLMngIpRangeIdx
OBJECT-TYPE
Applicable to all units. Index of an entry in the Management IP Address Ranges Table
1.3.6.1.4.1.12394.1.1.3.10.1.1INTEGER (1..10)read-onlycurrent
brzaccVLMngIpRangeFlag
OBJECT-TYPE
Applicable to all units. Defines the method of defining the range: Using Start & End Address( rangeDefinedByStartEndAddr ), or using Start Address and Mask ( rangeDefinedByStartAddrSubNetMask ).
1.3.6.1.4.1.12394.1.1.3.10.1.2INTEGER {rangeDefinedByStartEndAddr(1), rangeDefinedByStartAddrMask(2)}read-writecurrent
brzaccVLMngIpRangeStart
OBJECT-TYPE
Applicable to all units. Start Address of the range
1.3.6.1.4.1.12394.1.1.3.10.1.3IpAddressread-writecurrent
brzaccVLMngIpRangeEnd
OBJECT-TYPE
Applicable to all units. End Address of the range. Used only if brzaccVLMngIpRangeFlag is rangeDefinedByStartEndAddr
1.3.6.1.4.1.12394.1.1.3.10.1.4IpAddressread-writecurrent
brzaccVLMngIpRangeMask
OBJECT-TYPE
Applicable to all units. End Address of the range. Used only if brzaccVLMngIpRangeFlag is rangeDefinedByStartAddrMask
1.3.6.1.4.1.12394.1.1.3.10.1.5IpAddressread-writecurrent
brzaccVLDeleteOneNwIpRange
OBJECT-TYPE
Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Ranges Table.
1.3.6.1.4.1.12394.1.1.3.11INTEGER (0 | 1..10 | 255)read-writecurrent
brzaccVLDeleteAllNwIpRanges
OBJECT-TYPE
Applicable to all units. Deletes all entries from the Management IP Ranges Table.
1.3.6.1.4.1.12394.1.1.3.12INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
brzaccVLApClientIpAddress
OBJECT-TYPE
Applicable to SU/RB unit only. The IP Address of the WIFI WIMAX unit
1.3.6.1.4.1.12394.1.1.3.13IpAddressread-writecurrent
brzaccVLIpParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.4
brzaccVLUnitIpAddress
OBJECT-TYPE
Applicable to all units. IP address of the unit.
1.3.6.1.4.1.12394.1.1.4.1IpAddressread-writecurrent
brzaccVLSubNetMask
OBJECT-TYPE
Applicable to all units. Subnet mask of the unit.
1.3.6.1.4.1.12394.1.1.4.2IpAddressread-writecurrent
brzaccVLDefaultGWAddress
OBJECT-TYPE
Applicable to all units. Default gateway IP address of the unit.
1.3.6.1.4.1.12394.1.1.4.3IpAddressread-writecurrent
brzaccVLUseDhcp
OBJECT-TYPE
Applicable to all units. DHCP client mode of operation. disabled : Use regular (manual) methods to configure IP parameters. dHCP Only: Use DHCP server to configure IP parameters. automatic: Use DHCP server to configure IP parameters. If a DHCP server is not available, use manually configured values.
1.3.6.1.4.1.12394.1.1.4.4INTEGER {disable(1), dhcpOnly(2), automatic(3)}read-writecurrent
brzaccVLAccessToDHCP
OBJECT-TYPE
Applicable to all units. The port to be used for communicating with a DHCP server.
1.3.6.1.4.1.12394.1.1.4.5INTEGER {fromWirelessOnly(1), fromEthernetOnly(2), fromBothWirelessAndEthernet(3)}read-writecurrent
brzaccVLRunTimeIPaddr
OBJECT-TYPE
Applicable to all units. The run-time IP address. If DHCP is used the Run Time IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
1.3.6.1.4.1.12394.1.1.4.6IpAddressread-onlycurrent
brzaccVLRunTimeSubNetMask
OBJECT-TYPE
Applicable to all units. The run-time Subnet Mask. If DHCP is used the Run Time Subnet Mask is the mask given to the unit by the server. Otherwise it is the manually configured mask.
1.3.6.1.4.1.12394.1.1.4.7IpAddressread-onlycurrent
brzaccVLRunTimeDefaultIPGateway
OBJECT-TYPE
Applicable to all units. The run-time Gateway IP address. If DHCP is used the Run Time Gateway IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
1.3.6.1.4.1.12394.1.1.4.8IpAddressread-onlycurrent
brzaccVLBridgeParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5
brzaccVLVLANSupport
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1
brzaccVLVlanID
OBJECT-TYPE
Applicable to SU/RB only. VLAN ID for data frame tagging. Applicable to Access Link only. Range: 1 to 4094. 0 - not applicable.
1.3.6.1.4.1.12394.1.1.5.1.1INTEGERread-writecurrent
brzaccVLEthernetLinkType
OBJECT-TYPE
Applicable to all units. VLAN support mode (Link Type). The Access Link option is not available for AU/BU. Service Provider Link is not available for BU/RB.
1.3.6.1.4.1.12394.1.1.5.1.2INTEGER {accessLink(1), trunkLink(2), hybridLink(3), serviceProviderLink(4)}read-writecurrent
brzaccVLManagementVlanID
OBJECT-TYPE
Applicable to all units. VLAN ID for management frame tagging. Range: 1 to 4094, 65535 for No VLAN tagging.
1.3.6.1.4.1.12394.1.1.5.1.3INTEGERread-writecurrent
brzaccVLVLANForwarding
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.4
brzaccVLVlanForwardingSupport
OBJECT-TYPE
Applicable to all units. Enables or disables the VLAN forwarding feature. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLVlanForwardingTable
OBJECT-TYPE
Applicable to all units. A VLAN Forwarding Table of up to 20 VLAN IDs of devices to which data frames are forwarded when VLAN Forwarding is Enabled. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.2not-accessiblecurrent
brzaccVLVlanForwardingEntry
OBJECT-TYPE
Applicable to all units. A VLAN Forwarding Table entry. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.4.2.1not-accessiblecurrent
brzaccVLVlanForwardingTableIdx
OBJECT-TYPE
Applicable to all units. A read only table index for a VLAN entry in the VLAN Forwarding Table.
1.3.6.1.4.1.12394.1.1.5.1.4.2.1.1INTEGER (1..20)read-onlycurrent
brzaccVLVlanIdForwarding
OBJECT-TYPE
Applicable to all units. The list of VLAN ID's in the VLAN ID Forwarding Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range : 0 to 4094
1.3.6.1.4.1.12394.1.1.5.1.4.2.1.2INTEGERread-writecurrent
brzaccVLVlanRelaying
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.5
brzaccVLVlanRelayingSupport
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. Enables or disables VLAN Relaying (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLVlanRelayingTable
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. A VLAN Relaying Table of up to 20 VLAN IDs of devices to which data frames are relayed when VLAN Relaying is Enabled. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.2not-accessiblecurrent
brzaccVLVlanRelayingEntry
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. A VLAN Relaying Table entry. (applicable in Trunk and Service Provider links only).
1.3.6.1.4.1.12394.1.1.5.1.5.2.1not-accessiblecurrent
brzaccVLVlanRelayingTableIdx
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. A table index for a VLAN entry in the VLAN Relaying Table.
1.3.6.1.4.1.12394.1.1.5.1.5.2.1.1INTEGER (1..20)read-onlycurrent
brzaccVLVlanIdRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. The list of VLAN ID's in the VLAN ID Relaying Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range: 0 to 4094 , 0 - remove entry.
1.3.6.1.4.1.12394.1.1.5.1.5.2.1.2INTEGERread-writecurrent
brzaccVLVLANTrafficPriority
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.6
brzaccVLVlanDataPriority
OBJECT-TYPE
Applicable to SU/RB only. Priority tagging for data frames. Applicable to Access Link only. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.1.6.1INTEGER {na(255)}read-writecurrent
brzaccVLVlanManagementPriority
OBJECT-TYPE
Applicable to all units. Priority tagging for management frames. Applicable to Access Link and Trunk Link only. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.1.6.2INTEGER {na(255)}read-writecurrent
brzaccVLVlanPriorityThreshold
OBJECT-TYPE
Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold for tagged frames received from Ethernet port. Applicable to Hybrid Link and Trunk Link only. Valid values: 0-7.
1.3.6.1.4.1.12394.1.1.5.1.6.3INTEGER {na(255)}read-writecurrent
brzaccVLVLANQinQ
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.1.7
brzaccVLQinQEthertype
OBJECT-TYPE
Applicable to AU and SU. Not applicable to BreezeNET-B units. The Ethernet type of the Service Provider Tag. The range is 0x8101(33025) - 0x9000(36864), 0x9100(37120), 0x9200(37376).
1.3.6.1.4.1.12394.1.1.5.1.7.1INTEGER (33025..36864 | 37120 | 37376)read-writecurrent
brzaccVLQinQProviderVlanID
OBJECT-TYPE
Applicable to SU only. VLAN ID of the Service Provider Tag.
1.3.6.1.4.1.12394.1.1.5.1.7.2INTEGER (1..4094)read-writecurrent
brzaccVLBridgeAgingTime
OBJECT-TYPE
Applicable to all units. Bridge aging time for devices on both the Ethernet and wireless link sides. Range: 20 to 2000 seconds.
1.3.6.1.4.1.12394.1.1.5.2INTEGERread-writecurrent
brzaccVLBroadcastRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. Enables/disables the relaying of broadcast messages to the wireless link.
1.3.6.1.4.1.12394.1.1.5.4INTEGER {disable(1), broadcastMulticastEnable(2), broadcastEnable(3), multicastEnable(4), na(255)}read-writecurrent
brzaccVLUnicastRelaying
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. Enables/disables the relaying of unicast messages to the wireless link.
1.3.6.1.4.1.12394.1.1.5.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLEthBroadcastFiltering
OBJECT-TYPE
Applicable to SU/RB only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable : No filtering. onEthernetOnly : Filters broadcasts received on the Ethernet port only. onWirelessOnly : Filters broadcasts received on the Wlan port only. onBothWirelessAndEth: Filters broadcasts received on both ports.
1.3.6.1.4.1.12394.1.1.5.6INTEGER {disable(1), onEthernetOnly(2), onWirelessOnly(3), onBothWirelessAndEthernet(4), na(255)}read-writecurrent
brzaccVLEthBroadcastingParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.7
brzaccVLDHCPBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of DHCP messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLPPPoEBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of PPPoE messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLARPBroadcastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the broadcasting of ARP messages, overriding the general *brzaccVLEthBroadcastFiltering Ethernet broadcast filtering option.
1.3.6.1.4.1.12394.1.1.5.7.3INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLEthBroadcastMulticastLimiterOption
OBJECT-TYPE
Applicable to all units. Enable/disable the limiter for multicast and broadcast packets.
1.3.6.1.4.1.12394.1.1.5.7.4INTEGER {disable(1), limitOnlyBroadcasts(2), limitMulticastsExceptBroadcasts(3), limitAllMulticasts(4)}read-writecurrent
brzaccVLEthBroadcastMulticastLimiterThreshold
OBJECT-TYPE
Applicable to all units. The limit on the number of multicast and broadcast packets when the Ethernet Broadcast/Multicast Limiter Option is enabled. Range: 0 to 204800
1.3.6.1.4.1.12394.1.1.5.7.5INTEGERread-writecurrent
brzaccVLEthBroadcastMulticastLimiterSendTrapInterval
OBJECT-TYPE
Applicable to all units. The minimum time between two successive traps that are sent indicating the number of packets that were dropped by the Ethernet Broadcast/Multicast Limiter since the last trap was sent. Range: 1 to 60 minutes
1.3.6.1.4.1.12394.1.1.5.7.6INTEGERread-writecurrent
brzaccVLToSPriorityParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.8
brzaccVLToSPrecedenceThreshold
OBJECT-TYPE
Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold (based on the ToS) for frames received from the Ethernet port. Range: 0 to 7.
1.3.6.1.4.1.12394.1.1.5.8.1INTEGERread-writecurrent
brzaccVLRoamingOption
OBJECT-TYPE
Applicable to SU/RB only. Disable/enable the roaming feature. When enabled, the SU/RB will start scanning for an AU/BU after about one second of not receiving beacons or data from current AU/BU. Once it found a new AU/BU, it will also send through the wireless network a roaming SNAP on behalf of its clients informing other devices in the network of their new location. When disabled, it will wait for about seven seconds before starting scanning, and it will not send a roaming SNAP.
1.3.6.1.4.1.12394.1.1.5.9INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLMacAddressDenyList
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.10
brzaccVLMacAddressDenyListTable
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. A list of up to 100 MAC Addresses of SUs. If brzaccVLMacAddressDenyListAction is set to denyList, these are SUs that are not allowed to transfer data to the AU. If brzaccVLMacAddressDenyListAction is set to allowList, only these SUs are allowed to transfer data to the AU.
1.3.6.1.4.1.12394.1.1.5.10.1not-accessiblecurrent
brzaccVLMacAddressDenyListEntry
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. An entry in the Mac Address Deny List Table.
1.3.6.1.4.1.12394.1.1.5.10.1.1not-accessiblecurrent
brzaccVLMacAddressDenyListTableIdx
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. A read only table index for a MAC Address entry in the Mac Address Deny List Table. Range: 1 to 100.
1.3.6.1.4.1.12394.1.1.5.10.1.1.1INTEGER (1..100)read-onlycurrent
brzaccVLMacAddressDenyListId
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. The list of MAC Addresses in the Mac Address Deny List Table. To Remove a MAC Address - SET the corresponding entry to 0. To Add a new MAC Address - SET an entry which is currently 0.
1.3.6.1.4.1.12394.1.1.5.10.1.1.2MacAddressread-writecurrent
brzaccVLMacAddressDenyListAdd
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. Add a MAC address to the MAC Address Deny List Table
1.3.6.1.4.1.12394.1.1.5.10.2MacAddressread-writecurrent
brzaccVLMacAddressDenyListRemove
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. Delete a MAC address from the MAC Address Deny List Table
1.3.6.1.4.1.12394.1.1.5.10.3MacAddressread-writecurrent
brzaccVLNumberOfMacAddressesInDenyList
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B units. Number of MAC addresses in the MAC Address Deny List Table.
1.3.6.1.4.1.12394.1.1.5.10.4INTEGER {na(255)}read-onlycurrent
brzaccVLMacAddressDenyListAction
OBJECT-TYPE
Applicable to AU only. Define the action to be used by the Mac Address Deny List. allowedList(2) means that the list becomes Allow list.
1.3.6.1.4.1.12394.1.1.5.10.5INTEGER {denyList(1), allowedList(2), na(255)}read-writecurrent
brzAccVLPortsControl
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.5.11
brzaccVLEthernetPortControl
OBJECT-TYPE
Applicable to SU/RB only. Enable/disable the Ethernet port. When disabled, only data frames are blocked. Management frames are accepted.
1.3.6.1.4.1.12394.1.1.5.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLAirInterface
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6
brzaccVLESSIDParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.1
brzaccVLESSID
OBJECT-TYPE
Applicable to all units. The Extended Service Set ID (ESSID) used to prevent the merging of collocated systems. The ESSID is accessible only with the write community string (administrator password). Up to 31 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.6.1.1DisplayString (SIZE(0..31))read-writecurrent
brzaccVLOperatorESSIDOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the use of the Operator ESSID.
1.3.6.1.4.1.12394.1.1.6.1.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLOperatorESSID
OBJECT-TYPE
Applicable to AU/BU only. A secondary ESSID to support easy installation of SUs as well as the use of the Best AU/BU feature. Accessible only with SNMP Write Community Up to 31 printable case sensitive ASCII characters.
1.3.6.1.4.1.12394.1.1.6.1.3DisplayString (SIZE(0..31))read-writecurrent
brzaccVLRunTimeESSID
OBJECT-TYPE
Applicable to SU/RB only. The ESSID of the associated AU/BU. Accessible only with SNMP Write Community. Up to 31 printable ASCII characters, case sensitive.
1.3.6.1.4.1.12394.1.1.6.1.4DisplayString (SIZE(31))read-onlycurrent
brzaccVLMaximumCellRadius
OBJECT-TYPE
Applicable to all units. For AU/BU: read-write. In units with SW version 2.0 and up - applicable only when the Cell Distance Mode is set to Manual. The highest distance from the AU/BU of any SU/RB served by it. Affects the maximum time the units wait for a response message and the slot size by taking into account the round trip propagation delay. For SU/RB: read-only. The distance is learned from the AU/BU. Range: For units below version 2.0 the range is 0 - 50000 Meters. Otherwise - the range is 0 to 54 Kilometers. 0 means no compensation (minimum slot size, maximal delay timeout).
1.3.6.1.4.1.12394.1.1.6.2INTEGERread-writecurrent
brzaccVLAIFS
OBJECT-TYPE
Applicable to AU and SU. Not applicable to BreezeNET-B products. Not applicable if Wireless Link Prioritization is enabled. Arbitration Inter-Frame Spacing (AIFS) value, in slots. This is the number of time slots that define the DIFS. (DIFS=SIFS+AIFS). A value of 1 should be used only in point-to-point applications to allow one unit to have advantage over the other unit.
1.3.6.1.4.1.12394.1.1.6.3INTEGER {oneSlot(1), twoSlots(2)}read-writecurrent
brzaccVLWirelessTrapThreshold
OBJECT-TYPE
Applicable to AU/BU only. A wireless link quality threshold, expressed in % of retransmissions, for sending the brzaccVLAUWirelessQualityTRAP. This trap indicate whether the quality has gone below or above the specified threshold. The Threshold Range: 1 to 100 (% retransmissions).
1.3.6.1.4.1.12394.1.1.6.4INTEGERread-writecurrent
brzaccVLTransmitPowerTable
OBJECT-TYPE
Applicable to all units. A table of transmit power parameters.
1.3.6.1.4.1.12394.1.1.6.5not-accessiblecurrent
brzaccVLTransmitPowerEntry
OBJECT-TYPE
Applicable to all units. An entry in the Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.5.1not-accessiblecurrent
brzaccVLTransmitPowerIdx
OBJECT-TYPE
Applicable to all units. An index of an entry in the Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.5.1.1INTEGER (1..4)read-onlycurrent
brzaccVLApplicableModulationLevel
OBJECT-TYPE
Applicable to all units. The applicable modulation level for an entry in the Transmit Power Table. Level 8 is not applicable to units with HW revision A.
1.3.6.1.4.1.12394.1.1.6.5.1.2INTEGER {level1to5(1), level6(2), level7(3), level8(4)}read-onlycurrent
brzaccVLMaximumTxPowerRange
OBJECT-TYPE
Applicable to all units. The allowed range for the brzaccVLTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
1.3.6.1.4.1.12394.1.1.6.5.1.3DisplayStringread-onlycurrent
brzaccVLTxPower
OBJECT-TYPE
Applicable to all units. Read-only for units with SW version 4.0 and higher. In AU/BU: The transmit power in dBm defined for the applicable rate. In SU/RB: If ATPC is disabled, this is the transmit power in dBm defined for the applicable rate. If ATPC is enabled, it serves as the initial transmit power in dBm for the ATPC algorithm. In SU/RB: The range is -10 dBm to the power value defined by brzaccVLMaximumTxPower for the applicable modulation level. In AU/BU: The range is -10 dBm to the power value defined by brzaccVLMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.5.1.4DisplayStringread-writecurrent
brzaccVLCurrentTxPower
OBJECT-TYPE
Applicable to SU/RB. The actual transmit power in dBm for the applicable rate. Range: -17 to the maximum value defined by brzaccVLMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.5.1.5DisplayStringread-onlycurrent
brzaccVLMaximumTransmitPowerTable
OBJECT-TYPE
Applicable to SU/RB only. A table of maximum transmit power parameters.
1.3.6.1.4.1.12394.1.1.6.6not-accessiblecurrent
brzaccVLMaximumTransmitPowerEntry
OBJECT-TYPE
Applicable to SU/RB only. An entry in the Maximum Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.6.1not-accessiblecurrent
brzaccVLMaximumTransmitPowerIdx
OBJECT-TYPE
Applicable to SU/RB only. An index of an entry in the Maximum Transmit Power Table.
1.3.6.1.4.1.12394.1.1.6.6.1.1INTEGER (1..4)read-onlycurrent
brzaccVLMaxTxApplicableModulationLevel
OBJECT-TYPE
Applicable to SU/RB only. The applicable modulation level for an entry in the Maximum Transmit Power Table. Level 8 is not applicable to units with HW revision A.
1.3.6.1.4.1.12394.1.1.6.6.1.2INTEGER {level1to5(1), level6(2), level7(3), level8(4)}read-onlycurrent
brzaccVLDefinedMaximumTxPowerRange
OBJECT-TYPE
Applicable to SU/RB only. The allowed range for the brzaccVLMaxTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
1.3.6.1.4.1.12394.1.1.6.6.1.3DisplayStringread-onlycurrent
brzaccVLMaxTxPower
OBJECT-TYPE
Applicable to SU/RB only. Read-only for units with SW version 4.0 and higher. The maximum value that can be configured for the brzaccVLTxPower parameter. This is also the maximum power level that can be reached by the ATPC algorithm. The range is -10 dBm to the maximum value defined by brzaccVLDefinedMaximumTxPowerRange for the applicable modulation level.
1.3.6.1.4.1.12394.1.1.6.6.1.4DisplayStringread-writecurrent
brzaccVLMaxNumOfAssociations
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. Sets the upper limit for the number of SUs that can be associated with the AU. Range: For regular AUs (AU-BS, AU-SA) the range is from 0 to 512 if encryption is disabled the range id form 0 to 124 if encryption is enabled For AUS-BS and AUS-SA with SW version 4.0 and higher the range is between 0 to 8 or 25 (via licensing). For AUS-BS and AUS-SA with SW version below 4.0 the range is between 0 to 5. BreezeNET-B products return 65535.
1.3.6.1.4.1.12394.1.1.6.10INTEGERread-writecurrent
brzaccVLBestAu
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.11
brzaccVLBestAuSupport
OBJECT-TYPE
Applicable to SU/RB only. Disable/enable the Best AU/BU selection mechanism.
1.3.6.1.4.1.12394.1.1.6.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLBestAuNoOfScanningAttempts
OBJECT-TYPE
Applicable to SU/RB only. The number of scanning attempts to collect information for the Best AU/BU decision. Range: 1 to 255.
1.3.6.1.4.1.12394.1.1.6.11.2INTEGERread-writecurrent
brzaccVLPreferredAuMacAddress
OBJECT-TYPE
Applicable to SU/RB only. The MAC address of the preferred AU/BU (overriding the Best AU/BU selection process). 000000000000 means no preferred AU/BU.
1.3.6.1.4.1.12394.1.1.6.11.3MacAddressread-writecurrent
brzaccVLNeighborAuTable
OBJECT-TYPE
Applicable to SU/RB only. A table of data on neighboring AUs/BUs.
1.3.6.1.4.1.12394.1.1.6.11.4not-accessiblecurrent
brzaccVLNeighborAuEntry
OBJECT-TYPE
Applicable to SU/RB only. An entry in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1not-accessiblecurrent
brzaccVLNeighborAuIdx
OBJECT-TYPE
Applicable to SU/RB only. An index of an entry in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.1INTEGER (1..20)read-onlycurrent
brzaccVLNeighborAuMacAdd
OBJECT-TYPE
Applicable to SU/RB only. A MAC address of an AU/BU in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.2MacAddressread-onlycurrent
brzaccVLNeighborAuESSID
OBJECT-TYPE
Applicable to SU/RB only. The ESSID of an AU/BU in the Neighbor AU/BU Table. Accessible only with SNMP Write Community.
1.3.6.1.4.1.12394.1.1.6.11.4.1.3DisplayStringread-onlycurrent
brzaccVLNeighborAuSNR
OBJECT-TYPE
Applicable to SU/RB only. The received signal quality (SNR) in dB of an AU/BU in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.4INTEGER {na(255)}read-onlycurrent
brzaccVLNeighborAuAssocLoadStatus
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU association load status in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.5INTEGER {full(1), notFull(2), na(255)}read-onlycurrent
brzaccVLNeighborAuMark
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU mark in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.6INTEGERread-onlycurrent
brzaccVLNeighborAuHwRevision
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU HW revision in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.7INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
brzaccVLNeighborAuCountryCode
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU supported country code in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.8INTEGERread-onlycurrent
brzaccVLNeighborAuSwVer
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU SW version in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.9DisplayStringread-onlycurrent
brzaccVLNeighborAuAtpcOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU ATPC option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.10INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuAdapModOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU adaptive modulation option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.11INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuBurstModeOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU burst mode option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.12INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuDfsOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU DFS option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.14INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuConcatenationOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU concatenation option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.15INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuLearnCountryCodeBySU
OBJECT-TYPE
Applicable to SU only. Starting with 4.0 is not applicable for BA4900 and BreezeNET B products. Neighbor AU Learn Country Code by SU configuration in the Neighbor AU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.17INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuSecurityMode
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU security mode configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.18INTEGER {wep(1), aesOCB(2), fips197(3), na(255)}read-onlycurrent
brzaccVLNeighborAuAuthOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU authentication option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.19INTEGER {openSystem(1), sharedKey(2), na(255)}read-onlycurrent
brzaccVLNeighborAuDataEncyptOption
OBJECT-TYPE
Applicable to SU/RB only. Neighbor AU/BU data encryption option configuration in the Neighbor AU/BU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.20INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLNeighborAuPerSuDistanceLearning
OBJECT-TYPE
Applicable to SU only. Neighbor AU per SU distance learning option configuration in the Neighbor AU Table.
1.3.6.1.4.1.12394.1.1.6.11.4.1.21INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLFrequencyDefinition
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12
brzaccVLSubBandLowerFrequency
OBJECT-TYPE
Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The lowest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
1.3.6.1.4.1.12394.1.1.6.12.1INTEGERread-writeobsolete
brzaccVLSubBandUpperFrequency
OBJECT-TYPE
Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The highest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
1.3.6.1.4.1.12394.1.1.6.12.2INTEGERread-writeobsolete
brzaccVLScanningStep
OBJECT-TYPE
Applicable to all units - For flexible Sub-Bands only. For units with version 2.0 and above this is a read-only parameter. The scanning step to be used for generating the frequency subset.
1.3.6.1.4.1.12394.1.1.6.12.3INTEGER {mhz-5(1), mhz-10(2), mhz-20(3), na(255)}read-writecurrent
brzaccVLFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all frequencies from the selected Sub-band.
1.3.6.1.4.1.12394.1.1.6.12.4not-accessiblecurrent
brzaccVLFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.4.1not-accessiblecurrent
brzaccVLFrequencySubsetTableIdx
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An index of an entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.4.1.1INTEGER (1..40)read-onlycurrent
brzaccVLFrequencySubsetFrequency
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.4.1.2INTEGERread-onlycurrent
brzaccVLFrequencySubsetActive
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.4.1.3INTEGER {active(1), notActive(2)}read-writecurrent
brzaccVLFrequencySubsetFrequencyNew
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Frequency Subset table. (Replaces brzaccVLFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.4.1.4DisplayStringread-writecurrent
brzaccVLSetSelectedFreqSubset
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used.
1.3.6.1.4.1.12394.1.1.6.12.5INTEGER {setSelectedFreqsSubset(1), cancel(2)}read-writecurrent
brzaccVLCurrentFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Current Frequency Subset table. In SU/RB it includes all frequencies that are currently used for scanning. In AU/BU it includes all frequencies that can be used by the DFS mechanism (if applicable)
1.3.6.1.4.1.12394.1.1.6.12.6not-accessiblecurrent
brzaccVLCurrentFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. An entry in the Current Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.6.1not-accessiblecurrent
brzaccVLCurrentFrequencySubsetTableIdx
OBJECT-TYPE
Applicable to SU/RB and to AU/BU. An index of an entry in the Current Frequency subset Table. Not applicable to SU/RB with SW version 4.0 and higher.
1.3.6.1.4.1.12394.1.1.6.12.6.1.1INTEGER (1..40)read-onlycurrent
brzaccVLCurrentFrequencySubsetFrequency
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLCurrentFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Current Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.6.1.2INTEGERread-onlycurrent
brzaccVLCurrentFrequencySubsetFrequencyNew
OBJECT-TYPE
Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Current Frequency Subset table. (Replaces brzaccVLCurrentFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.6.1.3DisplayStringread-onlycurrent
brzaccVLCurrentAUOperatingFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLCurrentUOperatingFrequencyNew to support a resolution of 0.5 MHz). The operating frequency in MHz. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.7INTEGERread-onlycurrent
brzaccVLAUDefinedFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLAUDefinedFrequencyNew to support a resolution of 0.5 MHz). For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.8INTEGERread-writecurrent
brzaccVLCurrentSUOperatingFrequency
OBJECT-TYPE
Applicable to SU/RB only. The frequency used currently by the unit. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.9DisplayStringread-onlycurrent
brzaccVLSubBandSelect
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.10
brzaccVLSelectSubBandIndex
OBJECT-TYPE
Applicable to all units with SW version below 4.0 For units with SW version 4.0 and up it is applicable only for AU/BU. For SU/RB it defines only the sub-band for the Spectrum Analyzer. The ID of the sub-band used by the unit.
1.3.6.1.4.1.12394.1.1.6.12.10.1INTEGERread-writecurrent
brzaccVLDFSParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.11
brzaccVLDFSOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the DFS Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLDFSChannelCheckTime
OBJECT-TYPE
Applicable to AU/BU only. Defines the time the unit checks the channel for presence of radar signals and does not transmit after power up or association or after moving to a new channel due to detecting radar in the used channel. Range: 1 to 3600 (seconds).
1.3.6.1.4.1.12394.1.1.6.12.11.3INTEGERread-writecurrent
brzaccVLDFSChannelAvoidancePeriod
OBJECT-TYPE
Applicable to AU/BU only. Defines the time after detecting radar signals in a channel of avoiding using the channel or adjacent channels in accordance with the bandwidth. Range: 1 to 60 (minutes).
1.3.6.1.4.1.12394.1.1.6.12.11.4INTEGERread-writecurrent
brzaccVLDFSSuWaitingOption
OBJECT-TYPE
Applicable to AU/BU only. Defines whether the associated SUs should wait for this AU/BU after it stopped transmitting due to radar detection, before they starts scanning for other AUs/BUs.
1.3.6.1.4.1.12394.1.1.6.12.11.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLDFSClearRadarDetectedChannelsAfterReset
OBJECT-TYPE
Applicable to AU/BU only. Clear Radar Detected and Adjacent to Radar channels after unit reset. Returns the unit to operate in default frequency.
1.3.6.1.4.1.12394.1.1.6.12.11.6INTEGER {cancel(1), clearRadarChannels(2), na(255)}read-writecurrent
brzaccVLDFSRadarDetectionChannelsTable
OBJECT-TYPE
Applicable to AU/BU only. Applicable only when DFS option is on. Displays the current channels defined in the sub-band and their radar detection status.
1.3.6.1.4.1.12394.1.1.6.12.11.7not-accessiblecurrent
brzaccVLDFSRadarDetectionChannelsEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the brzaccVLDFSRadarDetectionChannelsTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1not-accessiblecurrent
brzaccVLDFSChannelIdx
OBJECT-TYPE
Applicable to AU/BU only. Read-only. The index of the entry in the brzaccVLDFSRadarDetectionChannelsTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.1INTEGER (1..40)read-onlycurrent
brzaccVLDFSChannelFrequency
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLDFSChannelFrequency New to support a resolution of 0.5 MHz). The frequency in MHz of a channel in the DFS Radar Detection Channels Table.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.2INTEGERread-onlycurrent
brzaccVLDFSChannelRadarStatus
OBJECT-TYPE
Applicable to AU/BU only. The radar detection status of a channel in brzaccVLDFSRadarDetectionChannelTable.
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.3INTEGER {radarFree(1), adjacentToRadar(2), radarDetected(3)}read-onlycurrent
brzaccVLDFSChannelFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. The frequency of a channel in the DFS Radar Detection Channels Table. (Replaces brzaccVLDFSChannelFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.6.12.11.7.1.4DisplayStringread-onlycurrent
brzaccVLDFSMinimumPulsesToDetect
OBJECT-TYPE
Applicable to AU/BU only. Defines the minimum number of pulses to detect a radar. Range: 1 - 100.
1.3.6.1.4.1.12394.1.1.6.12.11.8INTEGERread-writecurrent
brzaccVLDFSChannelReuseParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.11.9
brzaccVLDFSChannelReuseOption
OBJECT-TYPE
Applicable to AU/BU only. Enabling/disabling the DFS Channel Reuse Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.11.9.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLDFSRadarActivityAssessmentPeriod
OBJECT-TYPE
Applicable to AU/BU only. Range: 1 to 12 (Houres).
1.3.6.1.4.1.12394.1.1.6.12.11.9.2INTEGERread-writecurrent
brzaccVLDFSMaximumNumberOfDetectionsInAssessmentPeriod
OBJECT-TYPE
Applicable to AU/BU only. Range: 1 to 10 (Times).
1.3.6.1.4.1.12394.1.1.6.12.11.9.3INTEGERread-writecurrent
brzaccVLCountryCodeLearningBySU
OBJECT-TYPE
Applicable to AU only. Starting with 4.0 it is nor applicable for BA4900 and BreezeNET B. Defines whether the SUs learn the country code of the AU.
1.3.6.1.4.1.12394.1.1.6.12.12INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLCurrentAUOperatingFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. The operating frequency in MHz. (Replaces brzaccVLCurrentAUOperatingFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.13DisplayStringread-onlycurrent
brzaccVLAUDefinedFrequencyNew
OBJECT-TYPE
Applicable to AU/BU. For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. (Replaces brzaccVLAUDefinedFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
1.3.6.1.4.1.12394.1.1.6.12.14DisplayStringread-writecurrent
brzaccVLAutoSubBandSelect
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.12.15
brzaccVLAutoSubBandSelectedFreqSubset
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.15.1INTEGER {setAllSelectedFreqsSubset(1), cancel(2)}read-writecurrent
brzaccVLAutoSubBandFrequencySubsetTable
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all available sub-bands and all the frequencies in these sub-bands.
1.3.6.1.4.1.12394.1.1.6.12.15.2not-accessiblecurrent
brzaccVLAutoSubBandFrequencySubsetEntry
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1not-accessiblecurrent
brzaccVLAutoSubBandFrequencySubsetBandIdx
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable Sub Band. This is the Sub Band ID of the relevant entry in the Country Dependent Parameters table. Serves also as an index of the entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.1INTEGER (1..5)read-onlycurrent
brzaccVLAutoSubBandFrequencySubsetFrequencyIdx
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable frequency in the applicable Sub Band. Serves also as an index of the entry in the Frequency subset Table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.2INTEGER (1..40)read-onlycurrent
brzaccVLAutoSubBandFrequencySubsetActive
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Auto Sub Band Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.3INTEGER {active(1), notActive(2)}read-writecurrent
brzaccVLAutoSubBandFrequencySubsetFrequency
OBJECT-TYPE
Applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of the entry in the Auto Sub Band Frequency Subset table.
1.3.6.1.4.1.12394.1.1.6.12.15.2.1.4DisplayStringread-onlycurrent
brzaccVLATPC
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.13
brzaccVLAtpcOption
OBJECT-TYPE
Applicable all units. Enabling/disabling the ATPC Algorithm.
1.3.6.1.4.1.12394.1.1.6.13.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLDeltaFromMinSNRLevel
OBJECT-TYPE
Applicable AU/BU only. The Minimum SNR Level plus the value of this parameter define the maximum desired level of the average SNR at the AU/BU. If the ATPC Option is enabled, than if the received SNR is above the maximum desired level, the AU/BU will transmit Power-Down messages to the applicable SU/RB. Range: 4 to 20 (dB).
1.3.6.1.4.1.12394.1.1.6.13.2INTEGERread-writecurrent
brzaccVLMinimumSNRLevel
OBJECT-TYPE
Applicable AU/BU only. Defines the minimum desired level of the average SNR at the AU/BU. Below this level, if *AtpcOption is enabled, the AU/BU will transmit ATPC Power-Up messages to the applicable SU/RB. The *MinimumSNRLevel cannot be higher than *MaximumSNRLevel. Range: 4 to 60 (dB).
1.3.6.1.4.1.12394.1.1.6.13.3INTEGERread-writecurrent
brzaccVLMinimumIntervalBetweenATPCMessages
OBJECT-TYPE
Applicable AU/BU only. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
1.3.6.1.4.1.12394.1.1.6.13.4INTEGERread-writecurrent
brzaccVLPowerLevelSteps
OBJECT-TYPE
Applicable AU/BU only. The step in dB that the SU/RB will use when receiving an ATPC Power-Up/Power-Down message. Range: 1 to 20 (dB).
1.3.6.1.4.1.12394.1.1.6.13.6INTEGERread-writecurrent
brzaccVLCellDistanceParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.15
brzaccVLCellDistanceMode
OBJECT-TYPE
Applicable AU/BU only. The selected mode of deciding on Cell Distance.
1.3.6.1.4.1.12394.1.1.6.15.1INTEGER {automatic(1), manual(2), na(255)}read-writecurrent
brzaccVLFairnessFactor
OBJECT-TYPE
Applicable AU/BU only. Not applicable to BreezeNET-B products for SW version below 4.0. The percentage of the maximum distance that is taken into account in the time slot calculation. Range: 0 to 100 (Percent). A value of 0 means the minimal slot size (9 microseconds). BreezeNET-B products with SW version below 4.0 return na.
1.3.6.1.4.1.12394.1.1.6.15.2INTEGER {na(255)}read-writecurrent
brzaccVLMeasuredCellDistance
OBJECT-TYPE
Applicable AU/BU only. The Maximum Cell Distance as calculated by the AU/BU. Range: 0 to 54 (Kilometers).
1.3.6.1.4.1.12394.1.1.6.15.3INTEGER {below-2-Km(1)}read-onlycurrent
brzaccVLUnitWithMaxDistance
OBJECT-TYPE
Applicable AU only. Not applicable to BreezeNET-B units. The MAC address of the unit with the maximum distance from the AU.
1.3.6.1.4.1.12394.1.1.6.15.4MacAddressread-onlycurrent
brzaccVLPerSuDistanceLearning
OBJECT-TYPE
Aplicable to AU only. Applicable only if Cell Distance Mode is set to Automatic. When disabled, all SUs in the cell will use for the ACK Timeout the computed distance of the farthest SU. When enabled, each SU will use its own computed distance
1.3.6.1.4.1.12394.1.1.6.15.5INTEGER {disable(1), enable(2)}read-writecurrent
brzaccVLScanningMode
OBJECT-TYPE
Applicable to SU/RB only. The scanning mode. In cells where the DFS Option is enabled Scanning Mode is forced to Passive.
1.3.6.1.4.1.12394.1.1.6.16INTEGER {passive(1), active(2)}read-writecurrent
brzaccVLAntennaGain
OBJECT-TYPE
Applicable to all units. Read-write in units where brzaccVLAntennaGainChange is supported. Read-only in units where brzaccVLAntennaGainChange is not supported. The net gain (including cable attenuation for detached antennas) of the antenna. Range: 0 - to Maximum EIRP defined by country code + 10 (dBi). A value of -2 (this value is configurable only in factory) means don't care. A value of -1 (this value is configurable only in factory) means that the unit will not transmit until the actual value is configured.
1.3.6.1.4.1.12394.1.1.6.17DisplayStringread-writecurrent
brzaccVLSpectrumAnalysisParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.18
brzaccVLSpectrumAnalysisChannelScanPeriod
OBJECT-TYPE
Applicable to all units. The period of staying on each channel for information gathering when performing Spectrum analysis. Range: 2-30 seconds.
1.3.6.1.4.1.12394.1.1.6.18.1INTEGERread-writecurrent
brzaccVLSpectrumAnalysisScanCycles
OBJECT-TYPE
Applicable to all units. The number of scanning cycles when performing Spectrum Analysis. Range: 1-100.
1.3.6.1.4.1.12394.1.1.6.18.2INTEGERread-writecurrent
brzaccVLAutomaticChannelSelection
OBJECT-TYPE
Applicable to AU/BU only. Defines weather the AU/BU shall choose the most noise free channel upon startup after spectrum analysis.
1.3.6.1.4.1.12394.1.1.6.18.3INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLSpectrumAnalysisActivation
OBJECT-TYPE
Applicable to all units. Activates spectrum analysis, the unit is automatically reset upon activation.
1.3.6.1.4.1.12394.1.1.6.18.4INTEGER {cancelOperation(1), activateNow(2)}read-writecurrent
brzaccVLSpectrumAnalysisStatus
OBJECT-TYPE
Applicable to all units. Defines weather the unit is currently under performing a spectrum analysis process.
1.3.6.1.4.1.12394.1.1.6.18.5INTEGER {inactive(1), currentlyActive(2)}read-onlycurrent
brzaccVLResetSpectrumCounters
OBJECT-TYPE
Applicable to all units. Resets the spectrum analysis counters.
1.3.6.1.4.1.12394.1.1.6.18.6INTEGER {cancelOperation(1), resetCounters(2)}read-writecurrent
brzaccVLSpectrumAnalysisInformationTable
OBJECT-TYPE
Applicable to all units. The spectrum analysis information table.
1.3.6.1.4.1.12394.1.1.6.18.7not-accessiblecurrent
brzaccVLSpectrumAnalysisInformationEntry
OBJECT-TYPE
Applicable to all units. The spectrum analysis information table entry.
1.3.6.1.4.1.12394.1.1.6.18.7.1not-accessiblecurrent
brzaccVLSpectrumAnalysisInformationTableIdx
OBJECT-TYPE
Applicable to all units. A read only table index for a Spectrum Analysis Information entry in the Spectrum Analysis Information Table.
1.3.6.1.4.1.12394.1.1.6.18.7.1.1INTEGER (1..60)read-onlycurrent
brzaccVLSpectrumAnalysisInformationChannel
OBJECT-TYPE
Applicable to all units. The channels in the Spectrum Analysis Information Table. If the unit is currently under spectrum analysis the channels would be those on which the analysis is currently performed. If the unit is in normal mode the channels would be the those on which the last analysis was performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.2DisplayStringread-onlycurrent
brzaccVLSpectrumAnalysisInformationSignalCount
OBJECT-TYPE
Applicable to all units. The number of signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.3INTEGERread-onlycurrent
brzaccVLSpectrumAnalysisInformationSignalSNR
OBJECT-TYPE
Applicable to all units. The approximate SNR of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the SNR would be of the analysis that is currently performed. If the unit is in normal mode the SNR would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.4INTEGERread-onlycurrent
brzaccVLSpectrumAnalysisInformationSignalWidth
OBJECT-TYPE
Applicable to all units. The average width of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the width would be of the analysis that is currently performed. If the unit is in normal mode the width would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.5INTEGERread-onlycurrent
brzaccVLSpectrumAnalysisInformationOFDMFrames
OBJECT-TYPE
Applicable to all units. The number of OFDM frames detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
1.3.6.1.4.1.12394.1.1.6.18.7.1.6INTEGERread-onlycurrent
brzaccVLMaxNumOfAssociationsLimit
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. Shows the limit for the number of SUs that can be associated with the AU. For AU-BS, AU-SA if Data Encryption is enabled, the upper limit is 124, otherwise it is 512. For AUS-BS, AUS-SA with SW version 4.0 and higher the upper limit is 8 or 25 (via licensing). For AUS-BS, AUS-SA with SW version below 4.0 the upper limit is 5. BreezeNET-B products return 65535.
1.3.6.1.4.1.12394.1.1.6.19INTEGERread-onlycurrent
brzaccVLDisassociate
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.20
brzaccVLDisassociateAllSUs
OBJECT-TYPE
Applicable to AU only. The AU shall disassociate all its associated units.
1.3.6.1.4.1.12394.1.1.6.20.1INTEGER {cancelOperation(1), disassociateAllSUs(2)}read-writecurrent
brzaccVLDisassociateSuByMacAddress
OBJECT-TYPE
Applicable to AU only. The AU shall disassociate the SU with the configured MAC address.
1.3.6.1.4.1.12394.1.1.6.20.2MacAddressread-writecurrent
brzaccVLTxControl
OBJECT-TYPE
Applicable to AU/BU only. Tx Control of the AU/BU. Starting with version 4.0 it is run-time. For SW version below 4.0 the unit reset itself. If set to ethernetStatusControl, the unit will not transmit if the Ethernet link is down. This parameter can be configured only via the ethernet port.
1.3.6.1.4.1.12394.1.1.6.21INTEGER {on(1), off(2), ethernetStatusControl(3)}read-writecurrent
brzaccVLLostBeaconsWatchdogThreshold
OBJECT-TYPE
Applicable to AU/BU only. The number of unsuccessful consecutive transmissions beacons before Internal refresh is performed. 0 means that the lost beacons watchdog is not used and internal refresh is not performed.
1.3.6.1.4.1.12394.1.1.6.22INTEGER (0 | 100..1000)read-writecurrent
brzaccVLTransmitPower
OBJECT-TYPE
Applicable to all units with SW version 4.0 and higher. The uniform transmit power for all modulation levels. For a specific modulation level the effective transmit power (brzaccVLTxPower) is the minimum between the uniform transmit power and the maximum transmit power for that modulation level.
1.3.6.1.4.1.12394.1.1.6.23INTEGERread-writecurrent
brzaccVLMaximumTxPower
OBJECT-TYPE
Applicable to only SU/RB with SW version 4.0 and higher. The Maximum Transmit Power for all modulation levels. The Maximum Transmit Power for a specific modulation level is the minimum between this parameter and the hardware limitation for that modulation level
1.3.6.1.4.1.12394.1.1.6.24INTEGERread-writecurrent
brzaccVLCountryCodeParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.6.25
brzaccVLCountryCodeReApply
OBJECT-TYPE
Applicable to all units. Re-apply country code parameters.
1.3.6.1.4.1.12394.1.1.6.25.1INTEGER {reapply(1), cancel(2), na(255)}read-writecurrent
brzaccVLServiceParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7
brzaccVLMaxDelay
OBJECT-TYPE
Applicable to SU only. Not applicable to BreezeNET-B products. The maximal time packets may be delayed by the CIR\MIR mechanism. Above the configured maximal period the packets are discarded. Range: 300 to 10000 milliseconds. BreezeNET-B products return 65535.
1.3.6.1.4.1.12394.1.1.7.6INTEGERread-writecurrent
brzaccVLMaxBurstDuration
OBJECT-TYPE
Applicable to AU and SU. Not applicable to BreezeNET-B products. The maximum time during which inactivity bonus time can be accumulated for future burst transmissions. Range: 0 to 2000 milliseconds. BreezeNET-B products return 65535
1.3.6.1.4.1.12394.1.1.7.7INTEGERread-writecurrent
brzaccVLGracefulDegradationLimit
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. The maximum limit for activating the graceful degradation algorithm. Range: 0 to 70% rate of the CIR. BreezeNET-B products return 255.
1.3.6.1.4.1.12394.1.1.7.8INTEGERread-writecurrent
brzaccVLMirOnlyOption
OBJECT-TYPE
Applicable to AU only. Not applicable to BreezeNET-B products. When brzaccMirOnly is enabled, it overrides the CIR/MIR algorithm for determining actual information rate and forces the algorithm to operate with MIR parameter settings only. When enabled, the Graceful Degradation algorithm is disabled.
1.3.6.1.4.1.12394.1.1.7.9INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLTrafficPrioritization
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10
brzaccVLTrafficPriVLAN
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.1
brzaccVLVLANPriorityThreshold
OBJECT-TYPE
Applicable to all units. If the VLAN Priority's value of the frame is less than or equal to this threshold the frame will get LOW priority, otherwise the frame will get HIGH priority. Untagged frames will get LOW priority
1.3.6.1.4.1.12394.1.1.7.10.1.1INTEGER (1..7)read-writecurrent
brzaccVLTrafficPriIPToS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.2
brzaccVLToSPrioritizationOption
OBJECT-TYPE
Applicable to all units. Disable/Enable IP ToS prioritization and choose the interpretation of the IP ToS field from IP header. ipPrecedence(2): The IP ToS field is defined by RFC791. In this case the prioritization will be done using the Precedence sub-field of IP ToS. This sub-field has 3 bits, so it can be between 0 and 7. dSCP(3): The IP ToS field is defined by RFC2474. In this case the prioritization will be done using the DSCP sub-field. The size of the sub-field is 6 bits, so the range is 0 to 63.
1.3.6.1.4.1.12394.1.1.7.10.2.1INTEGER {disable(1), ipPrecedence(2), dSCP(3)}read-writecurrent
brzaccVLIPPrecedenceThreshold
OBJECT-TYPE
Applicable to all units. The threshold of Precedence sub-field of IP ToS field from IP Header (RFC791) to be used when the ToS Prioritization Option is set to IP Precedence. If the Precedence sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.2.2INTEGER (0..7)read-writecurrent
brzaccVLIPDSCPThreshold
OBJECT-TYPE
Applicable to all units. The threshold of DSCP sub-field of IP ToS field from IP Header (RFC2474) to be used when ToS Prioritization Option is set to DSCP. If the DSCP sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.2.3INTEGER (0..63)read-writecurrent
brzaccVLTrafficPriUdpTcpPortRange
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3
brzaccVLUdpTcpPortRangePrioritizationOption
OBJECT-TYPE
Applicable to all units. Disable/Enable Prioritization using UDP and/or TCP Port Ranges. udpOnly(2) : prioritization will be done only for UDP packets tcpOnly(3) : prioritization will be done only for TCP packets udpANDtcp(4): prioritization will be done for UDP and TCP packets
1.3.6.1.4.1.12394.1.1.7.10.3.1INTEGER {disable(1), udpOnly(2), tcpOnly(3), udpANDtcp(4)}read-writecurrent
brzaccVLUdpPortRangeConfig
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3.2
brzaccVLUdpPortPriRTPRTCP
OBJECT-TYPE
Applicale to all units. RTP/RTCP ports prioritization option for UDP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port ) with destination port in the defined port ranges will get HIGH priority.
1.3.6.1.4.1.12394.1.1.7.10.3.2.1INTEGER {rtpANDrtcp(1), rtpOnly(2)}read-writecurrent
brzaccVLUdpPortRangeNum
OBJECT-TYPE
Applicable to all units. The number of entries in the UDP Port Range Table
1.3.6.1.4.1.12394.1.1.7.10.3.2.2INTEGERread-onlycurrent
brzaccVLUdpPortRangeTable
OBJECT-TYPE
Applicable to all units. A table of UDP port ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
1.3.6.1.4.1.12394.1.1.7.10.3.2.3not-accessiblecurrent
brzaccVLUdpPortRangeEntry
OBJECT-TYPE
Applicable to all units. A UDP Port Ranges Table entry.
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1not-accessiblecurrent
brzaccVLUdpPortRangeStart
OBJECT-TYPE
Applicable to all units. Start port of an UDP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.1INTEGER (0..65535)read-onlycurrent
brzaccVLUdpPortRangeEnd
OBJECT-TYPE
Applicable to all units. End port of an UDP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.2INTEGER (0..65535)read-onlycurrent
brzaccVLUdpPortRangeIdx
OBJECT-TYPE
Applicable to all units. UDP Port Range Entry's index
1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.3INTEGER (1..64)read-onlycurrent
brzaccVLUdpPortRangeAdd
OBJECT-TYPE
Applicable to all units. Add port range(s) to UDP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can add several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.2.4DisplayString (SIZE(0..250))read-writecurrent
brzaccVLUdpPortRangeDelete
OBJECT-TYPE
Applicable to all units. Delete port range(s) from UDP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can delete several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.2.5DisplayString (SIZE(0..250))read-writecurrent
brzaccVLUdpPortRangeDeleteAll
OBJECT-TYPE
Applicable to all units. Delete all entries form UDP Port Ranges Table. Get operation will return 1
1.3.6.1.4.1.12394.1.1.7.10.3.2.6INTEGER {deleteAll(1), cancelOperation(2)}read-writecurrent
brzaccVLTcpPortRangeConfig
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.3.3
brzaccVLTcpPortPriRTPRTCP
OBJECT-TYPE
Applicable to all units. RTP/RTCP ports prioritization option for TCP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port )
1.3.6.1.4.1.12394.1.1.7.10.3.3.1INTEGER {rtpANDrtcp(1), rtpOnly(2)}read-writecurrent
brzaccVLTcpPortRangeNum
OBJECT-TYPE
Applicable to all units. The number of entries in the TCP Port Range Table
1.3.6.1.4.1.12394.1.1.7.10.3.3.2INTEGERread-onlycurrent
brzaccVLTcpPortRangeTable
OBJECT-TYPE
Table of TCP Port Ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
1.3.6.1.4.1.12394.1.1.7.10.3.3.3not-accessiblecurrent
brzaccVLTcpPortRangeEntry
OBJECT-TYPE
Applicable to all units. A TCP Port Ranges Table entry.
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1not-accessiblecurrent
brzaccVLTcpPortRangeStart
OBJECT-TYPE
Applicable to all units. Start port of a TCP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.1INTEGER (0..65535)read-onlycurrent
brzaccVLTcpPortRangeEnd
OBJECT-TYPE
Applicable to all units. End port of a TCP Port Range
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.2INTEGER (0..65535)read-onlycurrent
brzaccVLTcpPortRangeIdx
OBJECT-TYPE
Applicable to all units. TCP Port Range Entry's index
1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.3INTEGER (1..64)read-onlycurrent
brzaccVLTcpPortRangeAdd
OBJECT-TYPE
Applicable to all units. Add port range(s) to TCP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can add several ranges using comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.3.4DisplayString (SIZE(0..250))read-writecurrent
brzaccVLTcpPortRangeDelete
OBJECT-TYPE
Applicable to all units. Delete port range(s) from TCP Port Ranges Table. Get operation will return the empty string. A range is defined <start>-<end> or <start> where <start> is the Start Port of the range and <end> is the End Port. If only <start> is specified the range is <start>-<start>. The value of <start> and <end> are between 0..65535. The user can delete several ranges using comma to separate between ranges. Example: 10-256,99,987-900
1.3.6.1.4.1.12394.1.1.7.10.3.3.5DisplayString (SIZE(0..250))read-writecurrent
brzaccVLTcpPortRangeDeleteAll
OBJECT-TYPE
Applicable to all units. Delete all entries form TCP Port Ranges Table Get operation will return 1
1.3.6.1.4.1.12394.1.1.7.10.3.3.6INTEGER {deleteAll(1), cancelOperation(2)}read-writecurrent
brzaccVLWirelessLinkPrioritization
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.10.4
brzaccVLWirelessLinkPrioritizationOption
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Enable/disable the traffic prioritization over the Wireless Link
1.3.6.1.4.1.12394.1.1.7.10.4.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLlowPriorityAIFS
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Define the AIFS (Arbitration Inter-frame Space) that will be used for transmitting Low Priority Traffic
1.3.6.1.4.1.12394.1.1.7.10.4.2INTEGER (3..254)read-writecurrent
brzaccVLHWRetriesHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has High Priority
1.3.6.1.4.1.12394.1.1.7.10.4.3INTEGER (0..14)read-writecurrent
brzaccVLHWRetriesLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has Low Priority
1.3.6.1.4.1.12394.1.1.7.10.4.4INTEGER (0..14)read-writecurrent
brzaccVLAUBurstDurationHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with High Priority packets. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.5INTEGER (0..40)read-writecurrent
brzaccVLAUBurstDurationLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with Low Priority packets. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.6INTEGER (0..40)read-writecurrent
brzaccVLSUBurstDurationHighPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU and the SUs/RB will learn it form AU/BU. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.7INTEGER (0..40)read-writecurrent
brzaccVLSUBurstDurationLowPriority
OBJECT-TYPE
Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU/BU and the SUs/RB will learn it from AU/BU. The time is given in 250 microseconds units
1.3.6.1.4.1.12394.1.1.7.10.4.8INTEGER (0..40)read-writecurrent
brzaccVLDrap
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.7.11
brzaccVLDrapSupport
OBJECT-TYPE
Applicable to AU. Not applicable to BreezeNET B products Disable/Enable the DRAP feature
1.3.6.1.4.1.12394.1.1.7.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLDrapUdpPort
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BreezeNET B products. The UDP port used for the DRAP server
1.3.6.1.4.1.12394.1.1.7.11.2INTEGER (8000..8200)read-writecurrent
brzaccVLDrapMaxNumberOfVoiceCalls
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BreezeNET B products. The maximum number of voice calls that can be supported by the AU
1.3.6.1.4.1.12394.1.1.7.11.3INTEGER (0..255)read-writecurrent
brzaccVLDrapTTL
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BreezeNET B products. The maximum time between two allocation requests
1.3.6.1.4.1.12394.1.1.7.11.4INTEGER (1..255)read-writecurrent
brzaccVLDrapNoOfActiveVoiceCalls
OBJECT-TYPE
Applicable to AU when DRAP support is enabled. Not applicable to BreezeNET B products. The current total number of active voice calls.
1.3.6.1.4.1.12394.1.1.7.11.5INTEGERread-onlycurrent
brzaccVLLowPriorityTrafficMinimumPercent
OBJECT-TYPE
The minimum percent of the traffic rate that is allocated to the low priority traffic
1.3.6.1.4.1.12394.1.1.7.12INTEGER (0..100)read-writecurrent
brzaccVLMIRThresholdPercent
OBJECT-TYPE
Applicable to AU only. MIR Threshold Percent
1.3.6.1.4.1.12394.1.1.7.14INTEGER (0..100)read-writecurrent
brzaccVLUserFilterParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.8
brzaccVLUserFilterOption
OBJECT-TYPE
Applicable to SU/RB only. Defines user-filtering options. disable: No filtering. iPOnly: Only IP protocol frames pass. userDefinedAddrOnly: Only ip frames to/from user defined IP addresses pass. pPPoE Only: Only PPPoE frames pass.
1.3.6.1.4.1.12394.1.1.8.1INTEGER {disable(1), ipOnly(2), userDefinedAddrOnly(3), pPPoEOnly(4), na(255)}read-writecurrent
brzaccVLIpFilterTable
OBJECT-TYPE
Applicable to SU/RB only. An IP Filter Table of up to 8 user defined addresses, or address groups, to be used if the selected User Filtering option is userDefinedAddrOnly.
1.3.6.1.4.1.12394.1.1.8.2not-accessiblecurrent
brzaccVLIpFilterEntry
OBJECT-TYPE
Applicable to SU/RB only. An IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1not-accessiblecurrent
brzaccVLIpID
OBJECT-TYPE
Applicable to SU/RB only. An IP address of an IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1.1IpAddressread-writecurrent
brzaccVLMaskID
OBJECT-TYPE
Applicable to SU/RB only. An IP Mask of an IP Filter Table entry. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group.
1.3.6.1.4.1.12394.1.1.8.2.1.2IpAddressread-writecurrent
brzaccVLIpFilterRange
OBJECT-TYPE
Applicable to SU/RB only. An addresses range for the IP Filter Table entry. The first address in the range is the IP address. O means that the range is not used. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group. Range: 0 to 255.
1.3.6.1.4.1.12394.1.1.8.2.1.3INTEGERread-writecurrent
brzaccVLIpFilterIdx
OBJECT-TYPE
Applicable to SU/RB only. A table index for the IP Filter Table entry.
1.3.6.1.4.1.12394.1.1.8.2.1.4INTEGER (1..8)read-onlycurrent
brzaccVLDeleteOneUserFilter
OBJECT-TYPE
Applicable to SU/RB only. Deletes a single selected entry from the IP Filter Table.
1.3.6.1.4.1.12394.1.1.8.3INTEGER {deletefirstEntry(1), deletesecondEntry(2), deletethirdEntry(3), deletefourthEntry(4), deletefifthEntry(5), deletesixthEntry(6), deleteseventhEntry(7), deleteeighthEntry(8), cancelOperation(9), na(255)}read-writecurrent
brzaccVLDeleteAllUserFilters
OBJECT-TYPE
Applicable to SU/RB only. Deletes all entries from the IP Filter Table.
1.3.6.1.4.1.12394.1.1.8.4INTEGER {deleteAll(1), cancelOperation(2), na(255)}read-writecurrent
brzaccVLDHCPUnicastOverrideFilter
OBJECT-TYPE
Applicable to SU/RB only. Enables or disables the unicast DHCP messages, overriding the IP Filtering option.
1.3.6.1.4.1.12394.1.1.8.5INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLSecurityParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.9
brzaccVLAuthenticationAlgorithm
OBJECT-TYPE
Applicable to all units. Enables/disables the authentication encryption option. openSystem: Authentication messages are not encrypted. sharedKey : Authentication messages are encrypted
1.3.6.1.4.1.12394.1.1.9.1INTEGER {openSystem(1), sharedKey(2)}read-writecurrent
brzaccVLSUDefaultKeyID
OBJECT-TYPE
Applicable to SU/RB only. The key to be used for encryption of authentication messages and/or data. Range: 1 to 4.
1.3.6.1.4.1.12394.1.1.9.2INTEGERread-writecurrent
brzaccVLDataEncryptionOption
OBJECT-TYPE
Applicable to all units. Enables/disables the data encryption option.
1.3.6.1.4.1.12394.1.1.9.3INTEGER {disable(1), enable(2)}read-writecurrent
brzaccVLAUDefaultMulticastKeyID
OBJECT-TYPE
Applicable to AU/BU only. The key to be used for encryption of multicasts and broadcasts.
1.3.6.1.4.1.12394.1.1.9.4INTEGERread-writecurrent
brzaccVLSecurityMode
OBJECT-TYPE
Applicable to all units. The fips197 option is applicable only to units with a license to use FIPS 197 algorithm. The encryption algorithm to be used for authentication messages and/or data encryption.
1.3.6.1.4.1.12394.1.1.9.5INTEGER {wep(1), aesOCB(2), fips197(3)}read-writecurrent
brzaccVLAuthenticationPromiscuousMode
OBJECT-TYPE
Applicable to AU/BU only. Enables/disable the promiscuous mode allowing authentication of and communication with all SUs/RB regardless of their security parameters.
1.3.6.1.4.1.12394.1.1.9.6INTEGER {disable(1), enable(2)}read-writecurrent
brzaccVLKey1
OBJECT-TYPE
Applicable to all units. Key number 1. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.7DisplayString (SIZE(32))read-writecurrent
brzaccVLKey2
OBJECT-TYPE
Applicable to all units. Key number 2. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.8DisplayString (SIZE(32))read-writecurrent
brzaccVLKey3
OBJECT-TYPE
Applicable to all units. Key number 3. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.9DisplayString (SIZE(32))read-writecurrent
brzaccVLKey4
OBJECT-TYPE
Applicable to all units. Key number 4. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
1.3.6.1.4.1.12394.1.1.9.10DisplayString (SIZE(32))read-writecurrent
brzaccVLSecurityModeSupport
OBJECT-TYPE
Applicable to all units. Returns types of encryption that are supported. 0 - no encryption 1 - WEP 2 - AES OCB 3 - WEP and AES OCB 4 - FIPS-197 5 - FIPS-197 and WEP 6 - FIPS-197 and AES OCB 7 - FIPS-197, AES OCB and WEP
1.3.6.1.4.1.12394.1.1.9.12INTEGER (0..7)read-onlycurrent
brzaccVLPerformanceParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10
brzaccVLRTSThreshold
OBJECT-TYPE
Applicable to SU and AU. Not applicable to BreezeNET-B products. The minimum frame size that requires an RTS/CTS handshake. Range: For units bearing SW version 3.0 and above: 20 to 3400 bytes, for previous SW versions 20 to 1600 bytes. BreezeNET-B products return 65535.
1.3.6.1.4.1.12394.1.1.10.1INTEGERread-writecurrent
brzaccVLMinContentionWindow
OBJECT-TYPE
Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BreezeNET-B products, for previous SW versions not applicable to BreezeNET-B products. The initial value to be used by the contention window calculation algorithm. Value must be 0 or power of 2 minus 1 (7,15,31...). Range: 0 to 1023, excluding 1 and 3. BreezeNET-B products with SW version below 4.0 return 65535.
1.3.6.1.4.1.12394.1.1.10.3INTEGERread-writecurrent
brzaccVLMaxContentionWindow
OBJECT-TYPE
Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BreezeNET-B products, for previous SW versions not applicable to BreezeNET-B products. The maximum value to be used by the contention window calculation algorithm. Value must be power of 2 minus 1 (7,15,31...) Range: 7 to 1023.
1.3.6.1.4.1.12394.1.1.10.4INTEGERread-writecurrent
brzaccVLMaximumModulationLevel
OBJECT-TYPE
Applicable to all units. If the Adaptive Modulation algorithm is enabled, it sets the Maximum Modulation Level to be used. If The Modulation algorithm is disabled, it sets the Fixed Modulation Level to be used. The range is 1 to 8. 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.10.5INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-writecurrent
brzaccVLMulticastModulationLevel
OBJECT-TYPE
Applicable to AU/BU only. The modulation level for multicast and broadcast data frames. The range is 1 to 8. 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.10.6INTEGER {level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7), level8(8)}read-writecurrent
brzaccVLAvgSNRMemoryFactor
OBJECT-TYPE
Applicable to all units. The weight of history in average SNR calculation. The higher is the value, the higher is the weight of history. Range: -1 (Disregard History) to 32.
1.3.6.1.4.1.12394.1.1.10.7DisplayStringread-writecurrent
brzaccVLHardwareRetries
OBJECT-TYPE
Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. The maximum number of trials to transmit an unacknowledged frame in each Hardware Retrial phase. Range : 1 to 14.
1.3.6.1.4.1.12394.1.1.10.8INTEGERread-writecurrent
brzaccVLAdaptiveModulationParams
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.9
brzaccVLAdaptiveModulationAlgorithmOption
OBJECT-TYPE
Applicable to all units. Enables/disables the adaptive modulation level decision mechanism.
1.3.6.1.4.1.12394.1.1.10.9.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLSoftwareRetrySupport
OBJECT-TYPE
Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The status of the Software Retry mechanism. Enabled when the Adaptive Modulation algorithm is enabled and the Burst Mode Option is disabled. Otherwise it is disabled.
1.3.6.1.4.1.12394.1.1.10.9.2INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLNumOfSoftwareRetries
OBJECT-TYPE
Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The maximum number of times to use the Software Retry mechanism when it is enabled.
1.3.6.1.4.1.12394.1.1.10.9.3INTEGER {na(255)}read-writecurrent
brzaccVLMinIntervalBetweenAdaptiveModulationAlgorithmMessages
OBJECT-TYPE
Applicable all units. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
1.3.6.1.4.1.12394.1.1.10.9.4INTEGERread-writecurrent
brzaccVLAdaptiveModulationDecisionThresholds
OBJECT-TYPE
Applicable to all units. Defines the setting of thresholds for the rate decision algorithm. high (2) should typically be used when the SNR is lower than 13dB.
1.3.6.1.4.1.12394.1.1.10.9.5INTEGER {normal(1), high(2), na(255)}read-writecurrent
brzaccVLBurstMode
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.10
brzaccVLBurstModeOption
OBJECT-TYPE
Applicable to all units. Applicable only if Burst Mode Option is supported by country specific parameters of the Sub Band. Not applicable if Wireless Link Prioritization is enabled. Enables/disable burst mode operation. In SU/RB with HW Revision B or lower blocked(3) value is returned when Security Mode is Wep , Data Encryption Option is Enabled and Burst option is Enabled. In AU/BU with HW Revision B or lower blocked(3) value is returned when Dfs Option is Enabled and Burst mode is enabled.
1.3.6.1.4.1.12394.1.1.10.10.1INTEGER {disable(1), enable(2), blocked(3), na(255)}read-writecurrent
brzaccVLBurstInterval
OBJECT-TYPE
Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. Burst mode interval in milliseconds. Range: 1 to the maximum value as defined in the country specific parameters of the Sub Band (milliseconds).
1.3.6.1.4.1.12394.1.1.10.10.2INTEGERread-writecurrent
brzaccVLConcatenationParameters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.10.11
brzaccVLConcatenationOption
OBJECT-TYPE
Applicable to all units. Defines the Concatenation option.
1.3.6.1.4.1.12394.1.1.10.11.1INTEGER {disable(1), enable(2), na(255)}read-writecurrent
brzaccVLConcatenationMaximumNumberOfFrames
OBJECT-TYPE
Applicable to all units with SW version 3.X . Not applicable for version 4.0 and higher. Defines the maximum numbers of frames that can be concatenated. Range:2 to 8 (frames).
1.3.6.1.4.1.12394.1.1.10.11.2INTEGER (2..8)read-writecurrent
brzaccVLConcatenationMaxFrameSize
OBJECT-TYPE
Applicable to all units. Defines the maximum size of a concatenated frame. Range: 256 to 2200 (bytes) for BreezeNET-B products BU/RB14 BU/RB28, or for AU/SU with HW revision A or B. 256 to 4032 (bytes) for AU/SU with HW Revision C or higher and BreezeNET-B products BU/RB100.
1.3.6.1.4.1.12394.1.1.10.11.3INTEGERread-writecurrent
brzaccVLSiteSurvey
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11
brzaccVLAverageReceiveSNR
OBJECT-TYPE
Applicable to SU/RB only. The average Signal to Noise Ratio of received frames.
1.3.6.1.4.1.12394.1.1.11.1INTEGERread-onlycurrent
brzaccVLTrafficStatistics
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2
brzaccVLResetTrafficCounters
OBJECT-TYPE
Applicable to all units. Resets the traffic counters.
1.3.6.1.4.1.12394.1.1.11.2.1INTEGER {reset(1), cancel(2)}read-writecurrent
brzaccVLEthCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.2
brzaccVLTotalRxFramesViaEthernet
OBJECT-TYPE
Applicable to all units. Total number of frames received via the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.2.1Counter32read-onlycurrent
brzaccVLTxWirelessToEthernet
OBJECT-TYPE
Applicable to all units. Total number of frames transmitted to the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.2.2Counter32read-onlycurrent
brzaccVLWirelessLinkCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3
brzaccVLTxFramesToWireless
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3.1
brzaccVLAUBeaconsToWireless
OBJECT-TYPE
Applicable to AU/BU only. The number of beacons transmitted to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.1.1Counter32read-onlycurrent
brzaccVLDataAndOtherMngFramesToWireless
OBJECT-TYPE
Applicable to AU/BU only. The number of data and management frames transmitted to the wireless media. The count includes one count for each data frame transmitted successfully (excluding retransmissions).
1.3.6.1.4.1.12394.1.1.11.2.3.1.3Counter32read-onlycurrent
brzaccVLTotalTxFramesToWireless
OBJECT-TYPE
Applicable to all units. The number of frames transmitted to the wireless media. The count includes one count for each data frame that was transmitted successfully (excluding retransmissions), and also the number of transmitted control and management frames, including beacons.
1.3.6.1.4.1.12394.1.1.11.2.3.1.4Counter32read-onlycurrent
brzaccVLTotalTransmittedUnicasts
OBJECT-TYPE
Applicable to AU/BU only. The total number of unicast frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.5Counter32read-onlycurrent
brzaccVLTotalTransmittedConcatenatedFramesDouble
OBJECT-TYPE
Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.6Counter32read-onlycurrent
brzaccVLTotalTransmittedConcatenatedFramesSingle
OBJECT-TYPE
Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.7Counter32read-onlycurrent
brzaccVLTotalTransmittedConcatenatedFramesMore
OBJECT-TYPE
Applicable to all products. The total number of concatenated frames with more then two frames successfully transmitted to the wireless media, excluding retransmissions.
1.3.6.1.4.1.12394.1.1.11.2.3.1.8Counter32read-onlycurrent
brzaccVLTotalRxFramesFromWireless
OBJECT-TYPE
Applicable to all units. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU/BU. The count does not include frames that were discarded internally, bad frames and duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.2Counter32read-onlycurrent
brzaccVLTotalRetransmittedFrames
OBJECT-TYPE
Applicable to all units. The total number of retransmissions of data frames (counts all unsuccessful transmissions/retransmissions).
1.3.6.1.4.1.12394.1.1.11.2.3.3Counter32read-onlycurrent
brzaccVLFramesDropped
OBJECT-TYPE
Applicable to all units. The number of dropped frames. The frames that were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged..
1.3.6.1.4.1.12394.1.1.11.2.3.4Counter32read-onlycurrent
brzaccVLDataFramesSubmittedToBridge
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.3.5
brzaccVLFramesSubmittedViaHighQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the High priority queue. for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.1Counter32read-onlycurrent
brzaccVLFramesSubmittedViaMidQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the Mid priority queue for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.2Counter32read-onlycurrent
brzaccVLFramesSubmittedViaLowQueue
OBJECT-TYPE
Applicable to all units. Frames submitted to the internal bridge via the Low priority queue for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.3Counter32read-onlycurrent
brzaccVLTotalNoOfDataFramesSubmitted
OBJECT-TYPE
Applicable to all units. The total number of data frames submitted to the internal bridge for transmission to the wireless media.
1.3.6.1.4.1.12394.1.1.11.2.3.5.4Counter32read-onlycurrent
brzaccVLTotalRecievedDataFrames
OBJECT-TYPE
Applicable to all units. The total number of data frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.6Counter32read-onlycurrent
brzaccVLRecievedBadFrames
OBJECT-TYPE
Applicable to all units. The number of frames received from the wireless media with errors (CRC errors).
1.3.6.1.4.1.12394.1.1.11.2.3.7Counter32read-onlycurrent
brzaccVLNoOfDuplicateFramesDiscarded
OBJECT-TYPE
Applicable to all units. The number of frames discarded due to receiving multiple copies.
1.3.6.1.4.1.12394.1.1.11.2.3.8Counter32read-onlycurrent
brzaccVLNoOfInternallyDiscardedMirCir
OBJECT-TYPE
Applicable to all units. The number of data frames received from the Ethernet port that were discarded by the MIR/CIR mechanism either to avoid exceeding the maximum allowed information rate, or when the wireless link conditions do not enable reaching the allowed rate.
1.3.6.1.4.1.12394.1.1.11.2.3.9Counter32read-onlycurrent
brzaccVLTotalRxConcatenatedFramesDouble
OBJECT-TYPE
Applicable to all units. The total number of double concatenated frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.10Counter32read-onlycurrent
brzaccVLTotalRxConcatenatedFramesSingle
OBJECT-TYPE
Applicable to all units. The total number of data fast frames single concatenated frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.11Counter32read-onlycurrent
brzaccVLTotalRxConcatenatedFramesMore
OBJECT-TYPE
Applicable to all units. The total number of data fast frames concatenated with more then two frames received from the wireless media, including duplicate frames.
1.3.6.1.4.1.12394.1.1.11.2.3.12Counter32read-onlycurrent
brzaccVLWirelessLinkEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4
brzaccVLTxEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4.1
brzaccVLDroppedFrameEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were dropped because they were retransmitted to the maximum allowed number of retransmissions without being acknowledged.
1.3.6.1.4.1.12394.1.1.11.2.4.1.1Counter32read-onlycurrent
brzaccVLFramesDelayedDueToSwRetry
OBJECT-TYPE
Applicable to all units. Not applicable for units with SW Version 3.0 and higher. The number of frames that were delayed because the SW retry algorithm was activated on a previous frame designated for the same recipient.
1.3.6.1.4.1.12394.1.1.11.2.4.1.2Counter32read-onlycurrent
brzaccVLUnderrunEvents
OBJECT-TYPE
Applicable to all units. The number of frames whose transmission was aborted because the rate of submitting frames for transmission exceeded the available transmission capability.
1.3.6.1.4.1.12394.1.1.11.2.4.1.3Counter32read-onlycurrent
brzaccVLOthersTxEvents
OBJECT-TYPE
Applicable to all units. The number of Tx events due to problems other than those of the other Tx Events counters.
1.3.6.1.4.1.12394.1.1.11.2.4.1.4Counter32read-onlycurrent
brzaccVLTotalTxEvents
OBJECT-TYPE
Applicable to all units. The total number of Tx special events.
1.3.6.1.4.1.12394.1.1.11.2.4.1.5Counter32read-onlycurrent
brzaccVLRxEvents
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.4.2
brzaccVLPhyErrors
OBJECT-TYPE
Applicable to all units, only when DFS is enabled. The number of unidentified signals.
1.3.6.1.4.1.12394.1.1.11.2.4.2.1Counter32read-onlycurrent
brzaccVLCRCErrors
OBJECT-TYPE
Applicable to all units. The number of frames received from the wireless media containing CRC errors.
1.3.6.1.4.1.12394.1.1.11.2.4.2.2Counter32read-onlycurrent
brzaccVLOverrunEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were discarded because the receive rate exceeded the processing capability or the capacity of the Ethernet port.
1.3.6.1.4.1.12394.1.1.11.2.4.2.3Counter32read-onlycurrent
brzaccVLRxDecryptEvents
OBJECT-TYPE
Applicable to all units. The number of frames that were not received properly due to a problem in the data decryption mechanism.
1.3.6.1.4.1.12394.1.1.11.2.4.2.4Counter32read-onlycurrent
brzaccVLTotalRxEvents
OBJECT-TYPE
Applicable to all units. The total number of Rx special events.
1.3.6.1.4.1.12394.1.1.11.2.4.2.5Counter32read-onlycurrent
brzaccVLPerModulationLevelCounters
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.2.5
brzaccVLResetPerModulationLevelCounters
OBJECT-TYPE
Applicable to all units. Resets the per-Modulation Level counters .
1.3.6.1.4.1.12394.1.1.11.2.5.1INTEGER {resetCounters(1), cancel(2)}read-writecurrent
brzaccVLSUPerModulationLevelCountersTable
OBJECT-TYPE
Applicable to SU/RB. Per Rate Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2not-accessiblecurrent
brzaccVLSUPerModulationLevelCountersEntry
OBJECT-TYPE
Applicable to SU/RB. An entry in the Per modulation Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1not-accessiblecurrent
brzaccVLSUPerModulationLevelCountersTableIdx
OBJECT-TYPE
Applicable to SU/RB. An index of an entry in the Per modulation level Counters table.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.1INTEGER (1..8)read-onlycurrent
brzaccVLSUPerModulationLevelCountersApplicableModLevel
OBJECT-TYPE
Applicable to SU/RB. The applicable modulation level of the entry in the Per modulation level Counters table. Modulation Level 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.2INTEGER {modLevel-1(1), modLevel-2(2), modLevel-3(3), modLevel-4(4), modLevel-5(5), modLevel-6(6), modLevel-7(7), modLevel-8(8)}read-onlycurrent
brzaccVLSUPerModulationLevelCountersTxSuccess
OBJECT-TYPE
Applicable to SU/RB. The total number of successfully transmitted unicasts at the applicable modulation level.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.3Counter32read-onlycurrent
brzaccVLSUPerModulationLevelCountersTxFailed
OBJECT-TYPE
Applicable to SU/RB. The total number of dropped frames at the applicable Modulation Level.
1.3.6.1.4.1.12394.1.1.11.2.5.2.1.4Counter32read-onlycurrent
brzaccVLAverageModulationLevel
OBJECT-TYPE
Applicable to SU/RB. The average modulation level for successful transmission (rounded to nearest integer) since last reset of the Per Modulation Level counters. Range: 1 to 8.
1.3.6.1.4.1.12394.1.1.11.2.5.3INTEGERread-onlycurrent
brzaccVLMacAddressDatabase
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.5
brzaccVLAUMacAddressDatabase
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.5.1
brzaccVLAUAdbResetAllModulationLevelCounters
OBJECT-TYPE
Applicable to AU/BU only. To reset all the counters for all SUs/RB in the MAC Address Database.
1.3.6.1.4.1.12394.1.1.11.5.1.1INTEGER {reset(1), cancel(2)}read-writecurrent
brzaccVLAUAdbTable
OBJECT-TYPE
Applicable to AU/BU only. AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2not-accessiblecurrent
brzaccVLAUAdbEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1not-accessiblecurrent
brzaccVLAdbIndex
OBJECT-TYPE
Applicable to AU/BU only. The index of an entry in the AU/BU MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.1INTEGER (1..512)read-onlycurrent
brzaccVLAdbMacAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC Address of an SU/RB entry in the MAC Address Database table.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.2MacAddressread-onlycurrent
brzaccVLAdbStatus
OBJECT-TYPE
Applicable to AU/BU only. The status of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.3INTEGER {associated(1), authenticated(2), notAuthenticated(3)}read-onlycurrent
brzaccVLAdbSwVersion
OBJECT-TYPE
Applicable to AU/BU only. The SW version of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.4DisplayStringread-onlycurrent
brzaccVLAdbSNR
OBJECT-TYPE
Applicable to AU/BU only. The average Signal to Noise Ratio in dB of frames received by the AU/BU from the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.5INTEGERread-onlycurrent
brzaccVLAdbMaxModulationLevel
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the Maximum Modulation Level parameter. Modulation Level 8 is not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.6INTEGER {modLevel-1(1), modLevel-2(2), modLevel-3(3), modLevel-4(4), modLevel-5(5), modLevel-6(6), modLevel-7(7), modLevel-8(8)}read-onlycurrent
brzaccVLAdbTxFramesTotal
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.7Counter32read-onlycurrent
brzaccVLAdbDroppedFramesTotal
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of frames intended to the SU/RB that were dropped because they were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.8Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel1
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 1.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.9Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel2
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 2.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.10Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel3
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 3.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.11Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel4
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 4.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.12Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel5
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 5.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.13Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel6
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 6.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.14Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel7
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 7.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.15Counter32read-onlycurrent
brzaccVLAdbTxSuccessModLevel8
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 8. Not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.16Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel1
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 1.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.17Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel2
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 2.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.18Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel3
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 3.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.19Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel4
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 4.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.20Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel5
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 5.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.21Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel6
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 6.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.22Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel7
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 7.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.23Counter32read-onlycurrent
brzaccVLAdbTxFailedModLevel8
OBJECT-TYPE
Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 8. Not applicable for units with HW revision A.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.24Counter32read-onlycurrent
brzaccVLAdbCirTx
OBJECT-TYPE
Applicable to AU Only. Not applicable to BreezeNET-B products. Read-only. The value configured in the relevant SU for the CIR: SU to AU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.25INTEGERread-onlycurrent
brzaccVLAdbMirTx
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: SU/RB to AU/BU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.26INTEGERread-onlycurrent
brzaccVLAdbCirRx
OBJECT-TYPE
Applicable to AU Only. Not applicable to BreezeNET-B products. The value configured in the relevant SU for the CIR: AU to SU parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.27INTEGERread-onlycurrent
brzaccVLAdbMirRx
OBJECT-TYPE
Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: AU/BU to SU/RB parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.28INTEGERread-onlycurrent
brzaccVLAdbCirMaxDelay
OBJECT-TYPE
Applicable to AU Only. Not applicable to BreezeNET-B products. The value configured in the relevant SU for the CIR Maximum Delay parameter.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.29INTEGERread-onlycurrent
brzaccVLAdbDistance
OBJECT-TYPE
Applicable to AU/BU Only. The distance between the SU/RB and the AU/BU (In Kilometers).
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.30INTEGER {below-2-Km(1)}read-onlycurrent
brzaccVLAdbHwRevision
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB HW Revision.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.31INTEGER {hwRevisionA(1), hwRevisionB(2), hwRevisionC(3), hwRevisionD(4), hwRevisionE(5), na(255)}read-onlycurrent
brzaccVLAdbCpldVer
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB CPLD Version.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.32DisplayStringread-onlycurrent
brzaccVLAdbCountryCode
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB supported country code.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.33INTEGERread-onlycurrent
brzaccVLAdbBootVer
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB Boot Version.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.34DisplayStringread-onlycurrent
brzaccVLAdbAtpcOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB ATPC option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.35INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLAdbAdapModOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB adaptive modulation option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.36INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLAdbBurstModeOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB burst mode option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.37INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLAdbConcatenationOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB concatenation option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.39INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLAdbSecurityMode
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB security mode configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.41INTEGER {wep(1), aes(2), fips197(3), na(255)}read-onlycurrent
brzaccVLAdbAuthOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB authentication algorithm configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.42INTEGER {openSystem(1), sharedKey(2), na(255)}read-onlycurrent
brzaccVLAdbDataEncyptOption
OBJECT-TYPE
Applicable to AU/BU Only. The SU/RB data encryption option configuration.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.43INTEGER {disable(1), enable(2), na(255)}read-onlycurrent
brzaccVLAdbAge
OBJECT-TYPE
Applicable to AU/BU only. The time since any packet was received from the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.44INTEGERread-onlycurrent
brzaccVLAdbUnitName
OBJECT-TYPE
Applicable to AU/BU only. The unit name of the relevant SU/RB.
1.3.6.1.4.1.12394.1.1.11.5.1.2.1.45DisplayStringread-onlycurrent
brzaccVLUpLinkQualityIndicator
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.6
brzaccVLMeasureUpLinkQualityIndicator
OBJECT-TYPE
Applicable to SU/RB. Starts calculation of LQI. The calculation will be for a period of 10 seconds.
1.3.6.1.4.1.12394.1.1.11.6.1INTEGER {start(1), cancel(2)}read-writecurrent
brzaccVLReadUpLinkQualityIndicator
OBJECT-TYPE
Applicable to SU/RB. The results of the last LQI calculation. Range: 1 to 8.
1.3.6.1.4.1.12394.1.1.11.6.2INTEGERread-onlycurrent
brzaccVLUpLinkQualityIndicatorStatus
OBJECT-TYPE
Applicable to SU/RB Only. Indicates the test conditions. fullTest means that there are no limitations on the range of available modulation levels, and that all modulation levels from 1 to 8 can be used. limitedTest indicates that the results may not indicate the true quality since the available range is limited - by HW (HW Revision A), or by the applicable parameters in the country code, or by the configurable Maximum Modulation Level parameter.
1.3.6.1.4.1.12394.1.1.11.6.3INTEGER {fullTest(1), limitedTest(2)}read-onlycurrent
brzaccVLMacPinpoint
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.11.7
brzaccVLMacPinpointTable
OBJECT-TYPE
Applicable to AU/BU only. A table that contains information about wireless device used by a certain Ethernet station in order to connect to the wireless network
1.3.6.1.4.1.12394.1.1.11.7.1not-accessiblecurrent
brzaccVLMacPinpointEntry
OBJECT-TYPE
Applicable to AU/BU only. An entry in the MAC Pinpoint Table. Each entry contains an Ethernet station MAC address and the MAC address of the wireless device used to connect it to the wireless network
1.3.6.1.4.1.12394.1.1.11.7.1.1not-accessiblecurrent
mptEthernetStationMACAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC address of the Ethernet station. It is used as an index in the MAC Pinpoint Table.
1.3.6.1.4.1.12394.1.1.11.7.1.1.1MacAddressread-onlycurrent
mptUnitMACAddress
OBJECT-TYPE
Applicable to AU/BU only. The MAC address of the wireless device used by the station with the MAC Address from the index in order to access the wireless network.
1.3.6.1.4.1.12394.1.1.11.7.1.1.2MacAddressread-onlycurrent
brzaccVLDrapGatewaysTable
OBJECT-TYPE
This table provides information about Gateways supporting DRAP that are registered at the AU
1.3.6.1.4.1.12394.1.1.11.8not-accessiblecurrent
brzaccVLDrapGatewayEntry
OBJECT-TYPE
A Drap Gateway Entry.
1.3.6.1.4.1.12394.1.1.11.8.1not-accessiblecurrent
brzaccVLDrapGatewayIndex
OBJECT-TYPE
Gateway Entry's Index
1.3.6.1.4.1.12394.1.1.11.8.1.1INTEGER (1..512)read-onlycurrent
brzaccVLDrapGatewayIP
OBJECT-TYPE
The IP address of the Gateway
1.3.6.1.4.1.12394.1.1.11.8.1.2IpAddressread-onlycurrent
brzaccVLDrapGatewayType
OBJECT-TYPE
The Gateway type
1.3.6.1.4.1.12394.1.1.11.8.1.3INTEGER {vgDataVoice(4), vgData1Voice1(5), vgData4Voice2(6), vgDataVoice2(7), ngData4Wireless(11), vgUnknown(255)}read-onlycurrent
brzaccVLDrapGatewayNoOfActiveVoiceCalls
OBJECT-TYPE
The current number of active voice calls handled by the Gateway
1.3.6.1.4.1.12394.1.1.11.8.1.4INTEGERread-onlycurrent
brzaccVLTraps
OBJECT-IDENTITY
1.3.6.1.4.1.12394.1.1.14
brzaccVLTrapSUMacAddr
OBJECT-TYPE
Applicable to AU/BU only. SU/RB MAC Address.
1.3.6.1.4.1.12394.1.1.14.1MacAddressread-onlycurrent
brzaccVLTrapText
OBJECT-TYPE
Textual string for future use.
1.3.6.1.4.1.12394.1.1.14.3DisplayStringread-onlycurrent
brzaccVLTrapToggle
OBJECT-TYPE
Applicable to all units. An On/Off toggle status.
1.3.6.1.4.1.12394.1.1.14.4INTEGER {on(1), off(2)}read-onlycurrent
brzaccVLTrapParameterChanged
OBJECT-TYPE
Applicable to all units. A modification to one of the parameters related to CIR/MIR, IP Filtering or VLAN.
1.3.6.1.4.1.12394.1.1.14.5INTEGER {cirOrMir(1), ipFilter(2), vlan(4)}read-onlycurrent
brzaccVLTrapAccessRights
OBJECT-TYPE
Applicable to all units. The access rights used for login.
1.3.6.1.4.1.12394.1.1.14.6INTEGER {notLoggedIn(1), readOnly(2), installer(3), administrator(4), factory(5)}read-onlycurrent
brzaccVLTrapLog
OBJECT-TYPE
Applicable to all units. Login or logout to the Monitor program via Telnet.
1.3.6.1.4.1.12394.1.1.14.7INTEGER {telnetLogin(3), telnetLogout(4)}read-onlycurrent
brzaccVLTrapTelnetUserIpAddress
OBJECT-TYPE
Applicable to all units. The IP address of a Telnet user.
1.3.6.1.4.1.12394.1.1.14.8IpAddressread-onlycurrent
brzaccVLTrapRTx
OBJECT-TYPE
Applicable to AU/BU only. Retransmissions as a percentage of total transmissions.
1.3.6.1.4.1.12394.1.1.14.9INTEGERread-onlycurrent
brzaccVLTrapFtpOrTftpStatus
OBJECT-TYPE
Applicable to all units. The status of the last FTP/TFTP loading procedure.
1.3.6.1.4.1.12394.1.1.14.10INTEGER {successful(1), failed(2)}read-onlycurrent
brzaccVLDFSMoveFreq
OBJECT-TYPE
Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by brzaccVLTrapDFSMoveFreq New to support a resolution of 0.5 MHz). The new frequency in MHz after detecting radar on a previous channel.
1.3.6.1.4.1.12394.1.1.14.11INTEGERread-onlycurrent
brzaccVLDFSMoveFreqNew
OBJECT-TYPE
Applicable to AU/BU. The new frequency in MHz after detecting radar on a previous channel. (Replaces brzaccVLDFSMoveFreq to support a resolution of 0.5 MHz for units with HW revision C and higher).
1.3.6.1.4.1.12394.1.1.14.12DisplayStringread-onlycurrent
brzaccVLEthBroadcastThresholdExceeded
OBJECT-TYPE
Applicable to all units. The number of packets that are dropped by the ethernet broadcast/multicast limiter.
1.3.6.1.4.1.12394.1.1.14.13INTEGERread-onlycurrent
brzaccVLTrapSubscriberType
OBJECT-TYPE
Applicable to AUS only. The type of subscriber that was rejected by AUS
1.3.6.1.4.1.12394.1.1.14.14INTEGER {unknownSubscriberType(0), su-3(3), su-6(6), rb-14(14), su-24(24), rb-28(28), su-54(54), rb-100(100)}read-onlycurrent
brzaccVLTrapMACAddress
OBJECT-TYPE
Applicable to BU/RB only. The MAC address of the BNET B unit whose type has been changed
1.3.6.1.4.1.12394.1.1.14.15MacAddressread-onlycurrent
brzaccVLNewUnitTypeTrap
OBJECT-TYPE
Applicable to BU/RB only. The new type of the BNET B unit.
1.3.6.1.4.1.12394.1.1.14.16INTEGER {bu(1), rb(2)}read-onlycurrent
brzaccVLTrapSWVersion
OBJECT-TYPE
The SW version of the SU that tries to associate with a station that has Wireless Link Prioritization Enabled
1.3.6.1.4.1.12394.1.1.14.17DisplayStringread-onlycurrent
alvarionOID
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4
brzAccessVLOID
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1
brzAccessVLAU
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.1
brzAccessVLSU
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.2
brzAccessVLProducts
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.3
brzAccessVLAU_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.4
brzAccessVLAU_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.5
brzAccessVLAUS_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.6
brzAccessVLAUS_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.7
brzAccessAU_EZ
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.8
brzAccessVLSU_6_1D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.11
brzAccessVLSU_6_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.12
brzAccessVLSU_24_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.13
brzAccessVLSU_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.14
brzAccessVLSU_54_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.15
brzAccessVLSU_3_1D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.16
brzAccessVLSU_3_4D
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.17
brzAccessVLSU_I
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.18
brzNetB_BU_B14
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.21
brzNetB_BU_B28
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.22
brzNetB_BU_B100
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.23
brzNetB_RB_B14
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.31
brzNetB_RB_B28
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.32
brzNetB_RB_B100
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.33
brzAccess4900_AU_BS
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.41
brzAccess4900_AU_SA
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.42
brzAccess4900_SU_BD
OBJECT-IDENTITY
1.3.6.1.4.1.12394.4.1.51

Notifications

NameOIDStatus
brzaccVLSUassociatedAUTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating a new association with an SU/RB.
1.3.6.1.4.1.12394.4.1.3.2current
brzaccVLAUdisassociatedTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating that an SU/RB has been disassociated from the AU. The AU/BU decides that an SU/RB has been disassociated from it and remove it from the ADB after receiving from another AU/BU a SNAP frame with the SU/RB MAC address. The SNAP frame indicating a network topology change where the SU/RB has associated with another AU/BU will be received if both AUs/BUs are connected to the same Ethernet backbone.
1.3.6.1.4.1.12394.4.1.3.3current
brzaccVLAUagingTRAP
NOTIFICATION-TYPE
An AU/BU trap indicating that the unit association was aged out and removed from the Association database following its failure to acknowledge a specified number of consecutive frames.
1.3.6.1.4.1.12394.4.1.3.4current
brzaccVLSUassociatedTRAP
NOTIFICATION-TYPE
An SU/RB trap indicating association with an AU/BU. In addition to the MAC address information of the AU/BU, the trap also includes information on the average SNR of frames received from the AU/BU.
1.3.6.1.4.1.12394.4.1.3.6current
brzaccVLAUwirelessQualityTRAP
NOTIFICATION-TYPE
An AU/BU trap, indicating that the quality of the wireless link (retransmissions rate) has changed and dropped below (Off) or increased above (On) a threshold , defined by the *brzaccVLWirelessTrapThreshold. The threshold for AU/BU is a percentage of retransmissions.
1.3.6.1.4.1.12394.4.1.3.20current
brzaccVLPowerUpFromReset
NOTIFICATION-TYPE
An AU/BU trap indicating power up after Reset.
1.3.6.1.4.1.12394.4.1.3.101current
brzaccVLTelnetStatusTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating that a log-in or log-out has been performed via Telnet. Includes the log-in access right and the IP address of the PC performing Telnet.
1.3.6.1.4.1.12394.4.1.3.102current
brzaccVLParameterChangedTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating a change in a CIR/MIR, IP Filter or VLAN parameter.
1.3.6.1.4.1.12394.4.1.3.103current
brzaccVLLoadingStatusTRAP
NOTIFICATION-TYPE
Applicable to all units. A trap indicating that last FTP/TFTP loading process has been finished successfully or failed.
1.3.6.1.4.1.12394.4.1.3.104current
brzaccVLPromiscuousModeTRAP
NOTIFICATION-TYPE
An AU/BU trap, indicating that the AU/BU In (On) Promiscuous Mode or out (Off) Promiscuous Mode.
1.3.6.1.4.1.12394.4.1.3.105current
brzaccVLDFSRadarDetecetedTRAP
NOTIFICATION-TYPE
DFS: Applicable to AU/BU only. A trap indicating that a radar was detected.
1.3.6.1.4.1.12394.4.1.3.106current
brzaccVLDFSFrequcnyTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. A trap indicating that the unit moved to a new frequency.
1.3.6.1.4.1.12394.4.1.3.107current
brzaccVLDFSNoFreeChannelsExistsTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. A trap indicating that a radar was detected and there is no free channel.
1.3.6.1.4.1.12394.4.1.3.108current
brzaccVLEthBroadcastMulticatLimiterTRAP
NOTIFICATION-TYPE
Applicable to all units. The trap is send if the ethernet broadcast filter threshold is exceeded and it contains the number of dropped packets.
1.3.6.1.4.1.12394.4.1.3.109current
brzaccVLAUSUnsupportedSubscriberTypeTRAP
NOTIFICATION-TYPE
Applicable to AUS only. This trap is generated when a subscriber with unsupported type tries to associate to AUS. The AUS supports only SU-3 and SU-6. The first variable of the trap is the subscriber MAC Address. The second variable is the type of subscriber
1.3.6.1.4.1.12394.4.1.3.110current
brzaccVLUnitTypeChangedTRAP
NOTIFICATION-TYPE
Applicable to BU/RB only. This trap is generated when the user change the type of the BreezeNET B unit. The RB can be converted in BU or vice versa. The first variable of the trap is the unit MAC Address. The second variable is the new type of the unit
1.3.6.1.4.1.12394.4.1.3.111current
brzaccVLWLPrioritizationNotSupportedBySUTRAP
NOTIFICATION-TYPE
Applicable to AU/BU only. This trap is generated when an SU/RB with a SW version below 4.0 that does not support Wireless Link Prioritization is associated with an AU/BU with thw Wireless Link Prioritization Option enabled. The first variable of the trap is the SU/RB MAC Address. The second variable is the SW version of the SU/RB
1.3.6.1.4.1.12394.4.1.3.112current