MIBs Depot

ALCATEL-IND1-IPV6-MIB

Registered at
1.3.6.1.4.1.6486.801.1.2.1.29.1
Last updated
2019-11-27 00:00
Organization
ALE USA Inc.
Revisions
2024-07-15 00:00, 2024-06-11 00:00, 2024-05-27 00:00, 2019-11-28 00:00, 2019-11-27 00:00, 2019-04-29 00:00, 2018-01-29 00:00, 2016-09-26 00:00, 2016-09-22 00:00, 2016-04-12 00:00, 2015-03-24 00:00, 2014-10-14 00:00, 2014-09-18 00:00, 2014-08-12 00:00, 2014-05-20 00:00, 2014-02-28 00:00, 2013-07-30 00:00, 2013-07-29 00:00, 2013-03-13 00:00, 2012-02-07 00:00, 2011-03-09 00:00, 2010-05-13 00:00, 2010-01-06 00:00
Namespace
alcatel-aos7
Source file
ALCATEL-IND1-IPV6-MIB
Digest
sha256:8ebf402e511d97073bb83f13473ebaf9bcb834a116791a978a167f26ed218401

Description

This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) ALE USA Inc. 2014-2019 Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE

Contact

Please consult with Customer Service to ensure the most appropriate version of this document is used with the products in question: ALE USA Inc. Enterprise 26801 West Agoura Road Agoura Hills, CA 91301-5122 United States Of America Telephone: +1 800 995 2696 Electronic Mail: ebg_global_supportcenter@al-enterprise.com World Wide Web: https://www.al-enterprise.com

Imports

FromSymbols
ALCATEL-IND1-BASEsoftentIND1Ipv6
ALCATEL-IND1-VIRTUALROUTER-MIBalaVirtualRouterName
IF-MIBInterfaceIndexOrZero
IPV6-MIBipv6IfIndex, ipv6RouteEntry
IPV6-TCIpv6Address, Ipv6IfIndexOrZero
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ALCATEL-IND1-BASE
ALCATEL-IND1-IPV6-MIB
ALCATEL-IND1-VIRTUALROUTER-MIB
IANAifType-MIB
IF-MIB
IPV6-MIB
IPV6-TC
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
AlaIPv6AddressPrefix
TEXTUAL-CONVENTION
A data type for the 8 byte IPv6 prefixes for EUI-64 addresses
current
AlaIPv6RAFilterTrustedSourceIfIndex
TEXTUAL-CONVENTION
The ifIndex value identifying a trusted source port or link aggregation. The ifIndex value is in network byte order.
current
AlaIPv6RAFilterTrustedSourceType
TEXTUAL-CONVENTION
A value that represents the type of an RA Filter trusted source. port(1) A physical port or link aggregation ifIndex as defined by the AlaIPv6RAFilterTrustedSourceIfIndex textual convention netAddress(2) A layer 3 IPv6 address as defined by the Ipv6Address textual convention physAddress(3) A layer 2 physical address as defined by the PhysAddress textual convention
current
AlaIPv6RAFilterTrustedSourceValue
TEXTUAL-CONVENTION
The value identifying a trusted source. The value must be interpreted within the context of an AlaIPv6RAFilterTrustedSourceType value.
current
AlaIPv6RARouterPreference
TEXTUAL-CONVENTION
Router preference levels for Router Advertisement preference fields.
current

Objects

NameOIDSyntaxAccessStatus
alcatelIND1IPv6MIBNotifications
OBJECT-IDENTITY
Branch For IPv6 MIB Subsystem Notifications.
1.3.6.1.4.1.6486.801.1.2.1.29.1.0current
alcatelIND1IPv6MIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.1
alaIPv6Config
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1
alaIPv6ClearNeighbors
OBJECT-TYPE
Clear all non-static entries from the Neighbor table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.1INTEGER {clear(1)}read-writecurrent
alaIPv6ClearTraffic
OBJECT-TYPE
Reset all IPv6 traffic counters.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.2INTEGER {clear(1)}read-writecurrent
alaIPv6ClearPMTUTable
OBJECT-TYPE
Clear the path MTU table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.3INTEGER {clear(1)}read-writecurrent
alaIPv6PMTUMinLifetime
OBJECT-TYPE
Set the minimum lifetime for entries in the path MTU table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.4Unsigned32 (10..1440)read-writecurrent
alaIPv6NeighborStaleLifetime
OBJECT-TYPE
Set the minimum lifetime for neighbor entries in the stale state. In older versions of this MIB the default was specified as 1440 minutes.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.5Unsigned32 (5..2880)read-writecurrent
alaIPv6GlobalID
OBJECT-TYPE
The global ID used in the creation of local IPv6 unicast addresses (RFC 4193). An explicit value may be specified for the global ID or this object may be set to all zero to have a global ID be created based on the algorithm from the RFC.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.6OCTET STRING (SIZE(5))read-writecurrent
alaIPv6VirtualSourceMAC
OBJECT-TYPE
If set to enable(1) when a packet's source address is a VRRP virtual IPv6 address, the corresponding VRRP virtual MAC will be used as the source L2 address. If set to disable(2), the default, the interface's real MAC will be used as the source L2 address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.7INTEGER {enable(1), disable(2)}read-writecurrent
alaIPv6NeighborLimit
OBJECT-TYPE
The system-wide maximum size of the neighbor cache. A value of 0 indicates that no limit will be enforced. The minimum value is 200 entries.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.8Unsigned32read-writecurrent
alaIPv6NeighborVRFLimit
OBJECT-TYPE
The maximum size of the neighbor cache for a specific VRF. A value of 0 indicates that no limit is set. The minimum value is 200 entries.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.9Unsigned32read-writecurrent
alaIPv6IgnoreAnycastEchos
OBJECT-TYPE
If set to enable(1) no reply will be sent to an echo request sent to an anycast address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.10INTEGER {enable(1), disable(2)}read-writecurrent
alaIPv6IgnoreMcastEchos
OBJECT-TYPE
If set to enable(1) no reply will be sent to an echo request sent to a multicast address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.11INTEGER {enable(1), disable(2)}read-writecurrent
alaIPv6IcmpRateLimitInterval
OBJECT-TYPE
The minimum interval between ICMPv6 error messages, subject to the setting of alaIPv6IcmpRateLimitBurst. A value of 0 indicates no ICMPv6 rate limiting.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.12Unsigned32 (0..10000)read-writecurrent
alaIPv6IcmpRateLimitBurst
OBJECT-TYPE
The maximum number of ICMPv6 error messages that may be sent in a single burst.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.13Unsigned32 (1..50)read-writecurrent
alaIPv6DefaultDNSSLGroup
OBJECT-TYPE
The ID of the DNS Search List group of domains to be included in a Router Advertisement DNSSL options. A value of 0 indicates the system domain should be used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.14Unsigned32 (0..8)read-writecurrent
alaIPv6DefaultRDNSSGroup
OBJECT-TYPE
The ID of the RDNSS Search List group of domain servers to be included in a Router Advertisement RDNSS options. A value of 0 indicates the system DNS server address list should be used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.15Unsigned32 (0..8)read-writecurrent
alaIPv6InterfaceTable
OBJECT-TYPE
Table allowing the creation and removal of IPv6 interfaces. The table is indexed by ipv6IfIndex. The value of ipv6IfIndex shall be a four byte value in one of the following formats: 0x0000vvvv - The interface for VLAN vvvv 0x0100tttt - The interface for tunnel tttt 0x02000001 - The IPv6 loopback interface 0x0300nnnn - A loopback0 interface with ID nnnn 0x04000001 - The IPv6 EMP interface 0x0600ssss - A service interface with ID ssss The IPv6 loopback interface's configuration cannot be modified. A loopback0 interface's configuration cannog be modified other than to change its name or administrative status. When creating a new loopback0 interface, the special ipv6IfIndex value of 0x03000000 should be specified (ID of 0). Upon creation the interface will automatically be assigned its actual ID and ipv6IfIndex.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2not-accessiblecurrent
alaIPv6InterfaceEntry
OBJECT-TYPE
An IPv6 interface entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1not-accessiblecurrent
alaIPv6InterfaceRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.1RowStatusread-createcurrent
alaIPv6InterfaceDescription
OBJECT-TYPE
The IPv6 interface's description.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.2SnmpAdminString (SIZE(0..80))read-onlycurrent
alaIPv6InterfaceMtu
OBJECT-TYPE
The IPv6 interface's maximum transmission unit.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.3Unsigned32read-createcurrent
alaIPv6InterfaceType
OBJECT-TYPE
The interface type.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.4INTEGER {other(1), vlan(2), tunnel(3), loopback(4), emp(5), service(6)}read-onlycurrent
alaIPv6InterfaceAdminStatus
OBJECT-TYPE
Interface administrative status.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.5INTEGER {enable(1), disable(2)}read-createcurrent
alaIPv6InterfaceSendRouterAdvertisements
OBJECT-TYPE
Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is enable(1). Some interface types (e.g. 6to4 tunnel) cannot send router advertisements so the default (and only) value for those interfaces is disable(2).
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.6INTEGER {enable(1), disable(2)}read-createcurrent
alaIPv6InterfaceMaxRtrAdvInterval
OBJECT-TYPE
The maximum time allowed between sending unsolicited multicast router advertisements from the interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.7Unsigned32 (4..1800)read-createcurrent
alaIPv6InterfaceAdvManagedFlag
OBJECT-TYPE
The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.8TruthValueread-createcurrent
alaIPv6InterfaceAdvOtherConfigFlag
OBJECT-TYPE
The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.9TruthValueread-createcurrent
alaIPv6InterfaceAdvReachableTime
OBJECT-TYPE
The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.10Unsigned32 (0..3600000)read-createcurrent
alaIPv6InterfaceAdvRetransTimer
OBJECT-TYPE
The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.11Unsigned32read-createcurrent
alaIPv6InterfaceAdvDefaultLifetime
OBJECT-TYPE
The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds. The special value zero indicates that the router is not to be used as a default router. The special value 1 indicates that this object's true value should be computed using the formula 3 * alaIPv6InterfaceMaxRtrAdvInterval.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.12Unsigned32 (0..9000)read-createcurrent
alaIPv6InterfaceName
OBJECT-TYPE
The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically assigned.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.13SnmpAdminString (SIZE(1..32))read-createcurrent
alaIPv6InterfaceAdvSendMtu
OBJECT-TYPE
The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.14TruthValueread-createcurrent
alaIPv6InterfaceReachableTime
OBJECT-TYPE
In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioning to the stale state. Computed to be between .5 and 1.5 times the alaIPv6InterfaceBaseReachableTime.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.15Unsigned32read-onlycurrent
alaIPv6InterfaceBaseReachableTime
OBJECT-TYPE
The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.16Unsigned32 (10..3600)read-createcurrent
alaIPv6InterfaceMinRtrAdvInterval
OBJECT-TYPE
The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more than .75 times the value of alaIPv6InterfaceMaxRtrAdvInterval. Setting this object to the special value of 0 indicates that the minimum interval should be automatically recalculated using the formula .33 times the value of alaIPv6InterfaceMaxRtrAdvInterval.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.17Unsigned32 (0..1350)read-createcurrent
alaIPv6InterfaceClockSkew
OBJECT-TYPE
Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly synchronized clocks.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.18Unsigned32 (0..3600)read-createcurrent
alaIPv6InterfaceRetransTimer
OBJECT-TYPE
The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.19Unsigned32 (1000..30000)read-createcurrent
alaIPv6InterfaceDADTransmits
OBJECT-TYPE
The number of Neighbor Solicitations to send during Duplicate Address Detection. A value of 0 indicates that DAD will not be performed for addresses assigned to the interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.20Unsigned32 (0..10)read-createcurrent
alaIPv6InterfaceAdvHopLimit
OBJECT-TYPE
The value placed in the current hop limit field of router advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.21Unsigned32 (0..255)read-createcurrent
alaIPv6InterfaceLPND
OBJECT-TYPE
Enable/disable local proxy neighbor discovery.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.22INTEGER {enable(1), disable(2)}read-createcurrent
alaIPv6InterfaceRAFilter
OBJECT-TYPE
Enable/disable RA filtering. This object has been superseded by the alaIPv6RAFilterInterfaceTable.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.23INTEGER {enable(1), disable(2)}read-createdeprecated
alaIPv6InterfaceNeighborLimit
OBJECT-TYPE
The maximum number o neighbor entries that may be cached on this interface. A value of 0 indicates that no limit is set. The minimum value is 10.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.24Unsigned32read-createcurrent
alaIPv6InterfaceRetransBackoff
OBJECT-TYPE
The neighbor unreachability detection exponential backoff base. A value of 1 indicates the use of fixed interval retransmissions.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.25Unsigned32 (1..3)read-createcurrent
alaIPv6InterfaceRetransMax
OBJECT-TYPE
The maximum number of neighbor solicitations to be sent during neighbor discovery or neighbor unreachability detection.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.26Unsigned32 (1..10)read-createcurrent
alaIPv6InterfaceRouterPreference
OBJECT-TYPE
The preference a host should give to using this router as a default router.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.27AlaIPv6RARouterPreferenceread-createcurrent
alaIPv6InterfaceRoutedPortIfIndex
OBJECT-TYPE
The ifIndex of the physical port or linkagg bound to a routed port interface. For non-routed port interfaces this object will have the value 0.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.28InterfaceIndexOrZeroread-createcurrent
alaIPv6InterfaceRoutedPortTag
OBJECT-TYPE
For routed port interfaces, indicates if the traffic on the port is tagged or untagged. For non-routed port interfaces this object will have the value notApplicable.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.29INTEGER {notApplicable(1), untagged(2), tagged(3)}read-createcurrent
alaIPv6InterfaceAdvSendRDNSS
OBJECT-TYPE
The TRUE/FALSE value that determines whether the Recursive DNS Servers option is sent in Router Advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.30TruthValueread-createcurrent
alaIPv6InterfaceAdvSendDNSSL
OBJECT-TYPE
The TRUE/FALSE value that determines whether the DNS Search List option is sent in Router Advertisements.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.31TruthValueread-createcurrent
alaIPv6InterfaceAdvNat64Prefix
OBJECT-TYPE
Ipv6 address of RA nat64 prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.32Ipv6Addressread-createcurrent
alaIPv6InterfaceAdvNat64PrefixLength
OBJECT-TYPE
Ipv6 address of RA nat64 prefix length. The value 0 means no nat64 prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.33Unsigned32 (0 | 32 | 40 | 48 | 56 | 64 | 96)read-createcurrent
alaIPv6InterfaceAdvDNSSLGroup
OBJECT-TYPE
The ID of the DNS Search List group of domains to be included in the DNSSL option. A value of 0 indicates the default domain list should be used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.34Unsigned32 (0..8)read-createcurrent
alaIPv6InterfaceAdvRDNSSGroup
OBJECT-TYPE
The ID of the RDNSS Search List group of domain servers to be included in the RDNSS option. A value of 0 indicates the default domain list should be used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.35Unsigned32 (0..8)read-createcurrent
alaIPv6TunnelConfig
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3
alaIPv6ConfigTunnelTable
OBJECT-TYPE
Table for IPv6 configured tunnels. This table contains the tunnel-specific information extending the corresponding tunnel interface entry in alaIPv6InterfaceTable.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2not-accessiblecurrent
alaIPv6ConfigTunnelEntry
OBJECT-TYPE
A entry contains the objects for an IPv6 configured tunnel.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1not-accessiblecurrent
alaIPv6ConfigTunnelV4Source
OBJECT-TYPE
The source IPv4 address for the tunnel.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.1IpAddressread-createcurrent
alaIPv6ConfigTunnelV4Dest
OBJECT-TYPE
The destination IPv4 address for the tunnel.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.2IpAddressread-createcurrent
alaIPv6InterfaceAddressTable
OBJECT-TYPE
Table allowing the creation and removal of IPv6 addresses assigned to interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4not-accessiblecurrent
alaIPv6InterfaceAddressEntry
OBJECT-TYPE
An IPv6 interface address entry. The same link-local address may be assigned to multiple interfaces. A global address may only be assigned to a single interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1not-accessiblecurrent
alaIPv6InterfaceAddressRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 interface addresses.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.1RowStatusread-createcurrent
alaIPv6InterfaceAddress
OBJECT-TYPE
An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.2Ipv6Addressnot-accessiblecurrent
alaIPv6InterfaceAddressPrefixLength
OBJECT-TYPE
The number of bits that are significant in the IPv6 address' prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.3Unsigned32 (3..128)read-createcurrent
alaIPv6InterfaceAddressAnycastFlag
OBJECT-TYPE
This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.4TruthValueread-createcurrent
alaIPv6InterfaceAddressDADStatus
OBJECT-TYPE
The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such cases, duplicate address detection will be performed again for the address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.5INTEGER {unknown(0), pending(1), duplicate(2), passed(3), check(4)}read-createcurrent
alaIPv6InterfaceEUI64AddressTable
OBJECT-TYPE
Table allowing the creation and removal of IPv6 addresses formed by appending an EUI-64 interface identifier to the specified prefix. This table is mainly used for the creation of such addresses. After creation they can be managed via the alaIPv6InterfaceAddressTable.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5not-accessiblecurrent
alaIPv6InterfaceEUI64AddressEntry
OBJECT-TYPE
An IPv6 interface EUI-64 address entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1not-accessiblecurrent
alaIPv6InterfaceEUI64AddressRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 interface EUI-64 addresses.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.1RowStatusread-createcurrent
alaIPv6InterfaceEUI64AddressPrefix
OBJECT-TYPE
The prefix for the EUI-64 address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.2AlaIPv6AddressPrefixnot-accessiblecurrent
alaIPv6InterfaceEUI64AddressPrefixLength
OBJECT-TYPE
The number of bits that are significant in the IPv6 address' prefix. The prefix length must be in the range 3..64 or 128.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.3Unsigned32read-createcurrent
alaIPv6InterfaceEUI64AddressIdentifier
OBJECT-TYPE
The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.4OCTET STRING (SIZE(8))read-onlycurrent
alaIPv6NeighborTable
OBJECT-TYPE
The IPv6 neighbor table. Much of this information is available in the RFC-2465 ipv6NetToMediaTable. However, that table does not allow the static configuration of neighbor entries (all objects except for ipv6NetToMediaValid are read-only).
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6not-accessiblecurrent
alaIPv6NeighborEntry
OBJECT-TYPE
Each entry contains one IPv6 address to `physical' address equivalence (a neighbor).
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1not-accessiblecurrent
alaIPv6NeighborNetAddress
OBJECT-TYPE
The neighbor's IPv6 Address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.1Ipv6Addressnot-accessiblecurrent
alaIPv6NeighborPhysAddress
OBJECT-TYPE
The neighbor's media-dependent `physical' address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.2PhysAddressread-createcurrent
alaIPv6NeighborSlot
OBJECT-TYPE
The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not applicable. Superseded by alaIPv6NeighborPortIfIndex
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.3Unsigned32read-createobsolete
alaIPv6NeighborPort
OBJECT-TYPE
The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not applicable. Superseded by alaIPv6NeighborPortIfIndex.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.4Unsigned32read-createobsolete
alaIPv6NeighborType
OBJECT-TYPE
The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. All entries added via this table will have the type static(3) and only static entries may be removed via this table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.5INTEGER {other(1), dynamic(2), static(3), local(4), managed(5)}read-onlycurrent
alaIPv6NeighborState
OBJECT-TYPE
The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.6INTEGER {reachable(1), stale(2), delay(3), probe(4), invalid(5), unknown(6)}read-onlyobsolete
alaIPv6NeighborLastUpdated
OBJECT-TYPE
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.7TimeStampread-onlycurrent
alaIPv6NeighborRowStatus
OBJECT-TYPE
Used to control the addition and removal of static entries in the neighbor table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.8RowStatusread-createcurrent
alaIPv6NeighborLifetime
OBJECT-TYPE
The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero indicates the neighbor will remain in its current state indefinitely.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.9Unsigned32read-onlycurrent
alaIPv6NeighborReachability
OBJECT-TYPE
The reachability status of the neighbor.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.10INTEGER {confirmed(1), unconfirmed(2), incomplete(3)}read-onlycurrent
alaIPv6NeighborChassis
OBJECT-TYPE
On a multi-chasis system, the chassis used to reach the neighbor. On a single-chassis system this value is always 0. On read, a value of zero may indicate that the chassis is not known/not applicable. Superseded by alaIPv6NeighborPortIfIndex.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.11Unsigned32read-createobsolete
alaIPv6NeighborPortIfIndex
OBJECT-TYPE
The ifIndex of the port used to reach the neighbor. When creating a static neighbor the port ifIndex must be specified. On read, a value of zero indicates the port ifIndex is not known/not applicable. This object's value depends on the value of alaIPv6NeighborPortType. unknown - 0 physical - the ifIndex of the physical port linkagg - the ifIndex of the link aggregation sap - the ifIndex of the SAP sdp - the SDP ID
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.12Unsigned32read-createcurrent
alaIPv6NeighborPortType
OBJECT-TYPE
The type of port used to reach the neighbor.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.13INTEGER {unknown(0), physical(1), linkagg(2), sap(3), sdp(4)}read-onlycurrent
alaIPv6NeighborPortSubId
OBJECT-TYPE
The port sub-identifier for neighbors reached via virtual ports (alaIPv6NeighborPortType is sap or sdp). For SAP ports, this object holds a VLAN ID (1..4096) For SDP ports, this object holds the service ID (1..32767) For all other types this object's value will be 0 and should be ignored.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.14Unsigned32 (0..32767)read-onlycurrent
alaIPv6StaticRouteTable
OBJECT-TYPE
This table has been superseded by alaIprmV6StaticRouteTable in ALCATEL-IND1-IPRMV6-MIB. Table allowing the creation and removal of static IPv6 routes.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7not-accessibleobsolete
alaIPv6StaticRouteEntry
OBJECT-TYPE
A static route entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1not-accessibleobsolete
alaIPv6StaticRouteDest
OBJECT-TYPE
The destination IPv6 address of this static route. This object may not take a Multicast address value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.1Ipv6Addressnot-accessibleobsolete
alaIPv6StaticRoutePfxLength
OBJECT-TYPE
Indicates the prefix length of the destination address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.2Integer32 (0..128)not-accessibleobsolete
alaIPv6StaticRouteIfIndex
OBJECT-TYPE
If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop address types the value is zero.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.3Ipv6IfIndexOrZeroread-createobsolete
alaIPv6StaticRouteNextHop
OBJECT-TYPE
The IPv6 address of the next hop towards the destination.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.4Ipv6Addressread-createobsolete
alaIPv6StaticRouteMetric
OBJECT-TYPE
The routing metric for this route. The lower the value, the higher the priority for the static route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.5Unsigned32read-createobsolete
alaIPv6StaticRouteRowStatus
OBJECT-TYPE
Used to control the addition and removal of static routes.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.6RowStatusread-createobsolete
alaIPv6HostTable
OBJECT-TYPE
Local table mapping host names to IPv6 addresses. This provides the equivalent of /etc/hosts for IPv6.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8not-accessiblecurrent
alaIPv6HostEntry
OBJECT-TYPE
A entry maps a host name to an IPv6 address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1not-accessiblecurrent
alaIPv6HostName
OBJECT-TYPE
A host name to be mapped to an IPv6 address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.1SnmpAdminString (SIZE(1..64))not-accessiblecurrent
alaIPv6HostAddress
OBJECT-TYPE
The IPv6 address mapped to the host name.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.2Ipv6Addressnot-accessiblecurrent
alaIPv6HostRowStatus
OBJECT-TYPE
Allows host name/IPv6 address mappings to be created and deleted in this table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.3RowStatusread-createcurrent
alaIPv6InterfacePrefixTable
OBJECT-TYPE
Table allowing the creation and removal of IPv6 prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. Default: all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent. The link-local prefix is not included in the list of advertised prefixes.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9not-accessiblecurrent
alaIPv6InterfacePrefixEntry
OBJECT-TYPE
An IPv6 interface prefix entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1not-accessiblecurrent
alaIPv6InterfacePrefixRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.1RowStatusread-createcurrent
alaIPv6InterfacePrefix
OBJECT-TYPE
The prefix associated with this interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.2Ipv6Addressnot-accessiblecurrent
alaIPv6InterfacePrefixLength
OBJECT-TYPE
The length of the prefix in bits.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.3Unsigned32 (1..127)not-accessiblecurrent
alaIPv6InterfacePrefixValidLifetime
OBJECT-TYPE
The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.4Unsigned32read-createcurrent
alaIPv6InterfacePrefixOnLinkFlag
OBJECT-TYPE
The value to be placed in the on-link flag (L-bit) field in the Prefix Information option.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.5TruthValueread-createcurrent
alaIPv6InterfacePrefixPreferredLifetime
OBJECT-TYPE
The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.6Unsigned32read-createcurrent
alaIPv6InterfacePrefixAutonomousFlag
OBJECT-TYPE
The value to be placed in the Autonomous Flag field in the Prefix Information option.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.7TruthValueread-createcurrent
alaIPv6InterfacePrefixSource
OBJECT-TYPE
The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration the value will be dynamic(2).
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.8INTEGER {other(1), dynamic(2), configured(3)}read-onlycurrent
alaIPv6InterfacePrefixValidLifetimeDecrement
OBJECT-TYPE
If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixValidLifetime.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.9TruthValueread-createcurrent
alaIPv6InterfacePrefixValidLifetimeExpire
OBJECT-TYPE
The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.10DateAndTimeread-createcurrent
alaIPv6InterfacePrefixPreferredLifetimeDecrement
OBJECT-TYPE
If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixPreferredLifetime.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.11TruthValueread-createcurrent
alaIPv6InterfacePrefixPreferredLifetimeExpire
OBJECT-TYPE
The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.12DateAndTimeread-createcurrent
alaIPv6PMTUTable
OBJECT-TYPE
Table allowing the retrieval of the known IPv6 path MTU value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10not-accessiblecurrent
alaIPv6PMTUEntry
OBJECT-TYPE
An IPv6 path MTU entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1not-accessiblecurrent
alaIPv6PMTUDest
OBJECT-TYPE
The destination address of the IPv6 path.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.1Ipv6Addressnot-accessiblecurrent
alaIPv6PMTU
OBJECT-TYPE
The path's MTU.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.2Unsigned32read-onlycurrent
alaIPv6PMTUExpire
OBJECT-TYPE
The minimum time remaining before the PMTU entry is removed from the table.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.3Unsigned32read-onlycurrent
alaIPv6PMTUHits
OBJECT-TYPE
The number of times the path MTU entry has been used.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.4Counter32read-onlycurrent
alaIPv6PMTUUpdates
OBJECT-TYPE
The number of times the path MTU entry has been updated.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.5Counter32read-onlycurrent
alaIPv6RouteFlagsTable
OBJECT-TYPE
Table allowing the retrieval of the flags for IPv6 route entries.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11not-accessiblecurrent
alaIPv6RouteFlagsEntry
OBJECT-TYPE
An IPV6 route flags entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1not-accessiblecurrent
alaIPv6RouteFlagsUp
OBJECT-TYPE
True if the Up (U) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.1TruthValueread-onlycurrent
alaIPv6RouteFlagsGateway
OBJECT-TYPE
True if the Gateway (G) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.2TruthValueread-onlycurrent
alaIPv6RouteFlagsHost
OBJECT-TYPE
True if the Host (H) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.3TruthValueread-onlycurrent
alaIPv6RouteFlagsStatic
OBJECT-TYPE
True if the Static (S) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.4TruthValueread-onlycurrent
alaIPv6RouteFlagsCloneable
OBJECT-TYPE
True if the Cloneable (C) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.5TruthValueread-onlycurrent
alaIPv6RouteFlagsDiscard
OBJECT-TYPE
True if the Discard/Blackhole (B) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.6TruthValueread-onlycurrent
alaIPv6RouteFlagsECMP
OBJECT-TYPE
True if the ECMP (E) flag is set on the route.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.7TruthValueread-onlycurrent
alaIPv6RouteFlagsTransient
OBJECT-TYPE
True if route has not been replaced by valid route after takeover.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.8TruthValueread-onlycurrent
alaIPv6LocalUnicastTable
OBJECT-TYPE
Table allowing the creation and removal of local IPv6 unicast addresses (RFC 4193) on an interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13not-accessiblecurrent
alaIPv6LocalUnicastEntry
OBJECT-TYPE
An local unicast IPv6 address entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1not-accessiblecurrent
alaIPv6LocalUnicastGlobalID
OBJECT-TYPE
The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.1OCTET STRING (SIZE(5))not-accessiblecurrent
alaIPv6LocalUnicastSubnetID
OBJECT-TYPE
The subnet ID portion of the local IPv6 unicast address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.2OCTET STRING (SIZE(2))not-accessiblecurrent
alaIPv6LocalUnicastInterfaceID
OBJECT-TYPE
The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.3OCTET STRING (SIZE(8))not-accessiblecurrent
alaIPv6LocalUnicastPrefixLength
OBJECT-TYPE
The number of bits that are significant in the IPv6 address prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.4Unsigned32 (64..128)read-createcurrent
alaIPv6LocalUnicastEUI64
OBJECT-TYPE
If true(1) the interface identifier is formed from an automatically generated EUI-64 value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.5TruthValueread-createcurrent
alaIPv6LocalUnicastRowStatus
OBJECT-TYPE
Used to control the addition and removal of local IPv6 unicast addresses.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.6RowStatusread-createcurrent
alaIPv6RAFilterTrustedPortTable
OBJECT-TYPE
Table allowing the creation and removal of trusted ports for an interface's RA filtering. This table has been superseded by the alaIPv6RAFilterTrustedSourceTable
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.15not-accessibledeprecated
alaIPv6RAFilterTrustedPortEntry
OBJECT-TYPE
An RA filter trusted port entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.15.1not-accessibledeprecated
alaIPv6RAFilterTrustedPortIfIndex
OBJECT-TYPE
The ifIndex of a trusted physical port or link aggregation.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.15.1.1Unsigned32not-accessibledeprecated
alaIPv6RAFilterTrustedPortRowStatus
OBJECT-TYPE
Used to control the addition and removal of an RA filter's trusted ports.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.15.1.2RowStatusread-createdeprecated
alaIPv6RAFilterInterfaceTable
OBJECT-TYPE
Table to control operation of RA Filtering on a VLAN.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16not-accessiblecurrent
alaIPv6RAFilterInterfaceEntry
OBJECT-TYPE
An RA filter interface entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1not-accessiblecurrent
alaIPv6RAFilterInterfaceVlan
OBJECT-TYPE
The ID of the VLAN on which RA Filtering is to be configured.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.1Unsigned32not-accessiblecurrent
alaIPv6RAFilterInterfaceAdminStatus
OBJECT-TYPE
RA filtering administrative status.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.2INTEGER {enable(1), disable(2)}read-createcurrent
alaIPv6RAFilterInterfaceRowStatus
OBJECT-TYPE
Used to control the addition and removal of an interface's RA filter configuration.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.3RowStatusread-createcurrent
alaIPv6RAFilterTrustedSourceTable
OBJECT-TYPE
Table allowing the creation and removal of trusted sources for a VLAN's RA filtering.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17not-accessiblecurrent
alaIPv6RAFilterTrustedSourceEntry
OBJECT-TYPE
An RA filter trusted source entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1not-accessiblecurrent
alaIPv6RAFilterTrustedSourceType
OBJECT-TYPE
The type of the trusted source selector.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.1AlaIPv6RAFilterTrustedSourceTypenot-accessiblecurrent
alaIPv6RAFilterTrustedSourceValue
OBJECT-TYPE
The trusted source selector's value.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.2AlaIPv6RAFilterTrustedSourceValuenot-accessiblecurrent
alaIPv6RAFilterTrustedSourceRowStatus
OBJECT-TYPE
Used to control the addition and removal of a trusted source entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.3RowStatusread-createcurrent
alaIPv6EmpAddressTable
OBJECT-TYPE
Table allowing the creation and removal of IPv6 addresses assigned to the EMP interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18not-accessiblecurrent
alaIPv6EmpAddressEntry
OBJECT-TYPE
An IPv6 EMP address entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18.1not-accessiblecurrent
alaIPv6EmpAddressChassis
OBJECT-TYPE
The chassis on which to assign the EMP address. A value of 0 indicates the address is the VC master EMP address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18.1.1Unsigned32 (0..8)not-accessiblecurrent
alaIPv6EmpAddress
OBJECT-TYPE
The EMP IPv6 address. Each IPv6 address in this table must be unique.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18.1.2Ipv6Addressread-createcurrent
alaIPv6EmpAddressPrefixLength
OBJECT-TYPE
The EMP IPv6 address prefix length.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18.1.3Unsigned32 (3..128)read-createcurrent
alaIPv6EmpAddressRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 EMP addresses.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.18.1.4RowStatusread-createcurrent
alaIPv6DNSSLGroupConfigTable
OBJECT-TYPE
Table defining the mapping of DNS Search List group config names to IDs.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19not-accessiblecurrent
alaIPv6DNSSLGroupConfigEntry
OBJECT-TYPE
An DNS Search List group config entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19.1not-accessiblecurrent
alaIPv6DNSSLGroupConfigName
OBJECT-TYPE
The DNS Search List group config name.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19.1.1SnmpAdminString (SIZE(1..32))not-accessiblecurrent
alaIPv6DNSSLGroupConfigId
OBJECT-TYPE
The DNS Search List group's config ID.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19.1.2Unsigned32 (1..8)read-onlycurrent
alaIPv6DNSSLGroupConfigRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 DNS Search List groups config.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19.1.3RowStatusread-createcurrent
alaIPv6DNSSLGroupConfigLifeTime
OBJECT-TYPE
The DNS Search List group's config life time.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.19.1.4Unsigned32read-createcurrent
alaIPv6DNSSLGroupTable
OBJECT-TYPE
Table defining the mapping of DNS Search List group names to IDs.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.20not-accessiblecurrent
alaIPv6DNSSLGroupEntry
OBJECT-TYPE
An DNS Search List group entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.20.1not-accessiblecurrent
alaIPv6DNSSLGroupId
OBJECT-TYPE
The DNS Search List group's ID.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.20.1.1Unsigned32 (1..8)not-accessiblecurrent
alaIPv6DNSSLGroupName
OBJECT-TYPE
The DNS Search List group name.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.20.1.2SnmpAdminString (SIZE(1..32))read-onlycurrent
alaIPv6DNSSLDomainTable
OBJECT-TYPE
Table listing domains in a DNS Search List group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.21not-accessiblecurrent
alaIPv6DNSSLDomainEntry
OBJECT-TYPE
An DNSSL domain list.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.21.1not-accessiblecurrent
alaIPv6DNSSLDomainName
OBJECT-TYPE
A domain in the DNS Search List.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.21.1.1SnmpAdminString (SIZE(1..255))not-accessiblecurrent
alaIPv6DNSSLDomainRowStatus
OBJECT-TYPE
Used to control the addition and removal of DNS Search List domains.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.21.1.2RowStatusread-createcurrent
alaIPv6RDNSSGroupConfigTable
OBJECT-TYPE
Table defining the mapping of RDNSS Search List group config names to IDs.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22not-accessiblecurrent
alaIPv6RDNSSGroupConfigEntry
OBJECT-TYPE
An RDNSS Search List group config entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22.1not-accessiblecurrent
alaIPv6RDNSSGroupConfigName
OBJECT-TYPE
The RDNSS Search List group config name.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22.1.1SnmpAdminString (SIZE(1..32))not-accessiblecurrent
alaIPv6RDNSSGroupConfigId
OBJECT-TYPE
The RDNSS Search List group's config ID.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22.1.2Unsigned32 (1..8)read-onlycurrent
alaIPv6RDNSSGroupConfigRowStatus
OBJECT-TYPE
Used to control the addition and removal of IPv6 RDNSS Search List groups config.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22.1.3RowStatusread-createcurrent
alaIPv6RDNSSGroupConfigLifeTime
OBJECT-TYPE
The RDNSS Search List group's config life time.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.22.1.4Unsigned32read-createcurrent
alaIPv6RDNSSGroupTable
OBJECT-TYPE
Table defining the mapping of RDNSS Search List group names to IDs.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.23not-accessiblecurrent
alaIPv6RDNSSGroupEntry
OBJECT-TYPE
An RDNSS Search List group entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.23.1not-accessiblecurrent
alaIPv6RDNSSGroupId
OBJECT-TYPE
The RDNSS Search List group's ID.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.23.1.1Unsigned32 (1..8)not-accessiblecurrent
alaIPv6RDNSSGroupName
OBJECT-TYPE
The RDNSS Search List group config name.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.23.1.2SnmpAdminString (SIZE(1..32))read-onlycurrent
alaIPv6RDNSSAddressTable
OBJECT-TYPE
Table listing domain servers in a RDNSS Search List group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.24not-accessiblecurrent
alaIPv6RDNSSAddressEntry
OBJECT-TYPE
An DNS server list.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.24.1not-accessiblecurrent
alaIPv6RDNSSAddress
OBJECT-TYPE
A Address in the RDNSS Search List.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.24.1.1Ipv6Addressnot-accessiblecurrent
alaIPv6RDNSSAddressRowStatus
OBJECT-TYPE
Used to control the addition and removal of RDNSS Search List Address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.24.1.2RowStatusread-createcurrent
alaIPv6InterfaceRARouteInfoTable
OBJECT-TYPE
Table allowing the creation and removal of the IPv6 route prefixes to be placed in Route Information options in Router Advertisement messages sent from the interface.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25not-accessiblecurrent
alaIPv6InterfaceRARouteInfoEntry
OBJECT-TYPE
An IPv6 Route Information Option prefix entry.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1not-accessiblecurrent
alaIPv6InterfaceRARouteInfoRowStatus
OBJECT-TYPE
Used to control the addition and removal of the IPv6 route prefixes to be included in RA Route Information Option.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1.1RowStatusread-createcurrent
alaIPv6InterfaceRARouteInfoPrefix
OBJECT-TYPE
The IPv6 route prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1.2Ipv6Addressnot-accessiblecurrent
alaIPv6InterfaceRARouteInfoPrefixLength
OBJECT-TYPE
The IPv6 route prefix length .
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1.3Unsigned32 (0..128)not-accessiblecurrent
alaIPv6InterfaceRARouteInfoLifetime
OBJECT-TYPE
The length of time in seconds that the prefix is valid for route determination. A value of all one bits (0xffffffff) represents infinity.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1.4Unsigned32read-createcurrent
alaIPv6InterfaceRARouteInfoPreference
OBJECT-TYPE
The preference that should be given to using this router to reach the prefix.
1.3.6.1.4.1.6486.801.1.2.1.29.1.1.25.1.5AlaIPv6RARouterPreferenceread-createcurrent
alcatelIND1IPv6MIBConformance
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.2
alcatelIND1IPv6MIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1
alcatelIND1IPv6MIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2

Notifications

NameOIDStatus
ndpMaxLimitReached
NOTIFICATION-TYPE
This notification is generated when hardware table has reached supported Maximum entries. OS6400 will not generate new ARP request for new nexthops
1.3.6.1.4.1.6486.801.1.2.1.29.1.0.1deprecated
alaIPv6NeighborLimitExceeded
NOTIFICATION-TYPE
Notification that the system-wide neighbor cache limit has been exceeded.
1.3.6.1.4.1.6486.801.1.2.1.29.1.0.2current
alaIPv6NeighborVRFLimitExceeded
NOTIFICATION-TYPE
Notification that a per-VRF neighbor cache limit has been exceeded.
1.3.6.1.4.1.6486.801.1.2.1.29.1.0.3current
alaIPv6InterfaceNeighborLimitExceeded
NOTIFICATION-TYPE
Notification that a per-interface neighbor cache limit has been exceeded.
1.3.6.1.4.1.6486.801.1.2.1.29.1.0.4current

Conformance

NameOIDStatus
alaIPv6Compliance
MODULE-COMPLIANCE
The compliance statement for switches with Alcatel IPv6 stack and implementing ALCATEL-IND1-IPV6-MIB.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1.1current
alaIPv6TunnelConfigGroup
OBJECT-GROUP
A collection of objects to support management of Alcatel IPv6 tunneling.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.1current
alaIPv6ConfigGroup
OBJECT-GROUP
A collection of objects to support management of configuration parameters of Alcatel IPv6 stack.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.2current
alaIPv6NeighborGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 neighbors.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.3current
alaIPv6StaticRouteGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 static routes.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.4obsolete
alaIPv6InterfaceGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.5current
alaIPv6InterfaceAddressGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 addresses assigned to interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.6current
alaIPv6InterfaceEUI64AddressGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 EUI-64 addresses assigned to interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.7current
alaIPv6InterfacePrefixGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 prefixes assigned to interfaces.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.8current
alaIPv6PMTUGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 path MTUs.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.9current
alaIPv6RouteFlagsGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 route flags.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.10current
alaIPv6LocalUnicastGroup
OBJECT-GROUP
A collection of objects to support management of local IPv6 unicast addresses (RFC 4193).
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.11current
alaIPv6HostGroup
OBJECT-GROUP
A collection of objects to support management of IPv6 addresses assigned to Host.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.12current
alcatelIND1IPv6NotificationGroup
NOTIFICATION-GROUP
The AlcatelIND1IPv6 MIB Notification Group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.13current
alcatelIND1IPv6DeprecatedObjectGroup
OBJECT-GROUP
Deprecated/obsolete objects
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.14current
alcatelIND1IPv6DeprecatedNotificationGroup
NOTIFICATION-GROUP
Deprecated/obsolete notifications
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.15current
alaIPv6RAFilterGroup
OBJECT-GROUP
A collection of objects to support management of RA filtering.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.16current
alaIPv6EmpAddressGroup
OBJECT-GROUP
A collection of objects to support management of Emp Address.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.17current
alaIPv6DNSSLGroupConfigGroup
OBJECT-GROUP
A collection of objects to support management of RA DNSSL group config.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.18current
alaIPv6DNSSLGroupGroup
OBJECT-GROUP
A collection of objects to support management of RA DNSSL group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.19current
alaIPv6DNSSLDomainGroup
OBJECT-GROUP
A collection of objects to support management of RA DNSSL domain group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.20current
alaIPv6RDNSSGroupConfigGroup
OBJECT-GROUP
A collection of objects to support management of RA RDNSS group config.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.21current
alaIPv6RDNSSGroupGroup
OBJECT-GROUP
A collection of objects to support management of RA RDNSS group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.22current
alaIPv6RDNSSAddressGroup
OBJECT-GROUP
A collection of objects to support management of RA RDNSS address group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.23current
alaIPv6InterfaceRARouteInfoGroup
OBJECT-GROUP
A collection of objects to support management of RA Route information group.
1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.24current