MIBs Depot

AIRESPACE-SWITCHING-MIB

Registered at
1.3.6.1.4.1.14179.1
Last updated
2006-04-10 00:00
Organization
Airespace, Inc.
Revisions
2006-04-10 00:00
Namespace
cisco
Source file
AIRESPACE-SWITCHING-MIB
Digest
sha256:471552c8fb8144d66ca95150795278a7d9648ba2238b349e84454ddf68a0400c

Description

This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration, statistics and status information about the controller. This includes controller statistics and provides information such as Inventory, Trap logs, memory and CPU. This MIB also provides configuration of CLI, SNMP, LAG, DHCP, Spanning Tree, etc. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.

Contact

Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com

Imports

FromSymbols
AIRESPACE-REF-MIBairespace
IANAifType-MIBIANAifType
Q-BRIDGE-MIBdot1qFdbId, dot1qVlanIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

AIRESPACE-REF-MIB
AIRESPACE-SWITCHING-MIB
BRIDGE-MIB
IANAifType-MIB
IF-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Objects

NameOIDSyntaxAccessStatus
agentInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1
agentInventoryGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.1
agentInventorySysDescription
OBJECT-TYPE
The switch's Inventory system description.
1.3.6.1.4.1.14179.1.1.1.1DisplayStringread-onlycurrent
agentInventoryMachineType
OBJECT-TYPE
Type of the Machine used in the Switch.
1.3.6.1.4.1.14179.1.1.1.2DisplayStringread-onlycurrent
agentInventoryMachineModel
OBJECT-TYPE
The switch's Machine Model.
1.3.6.1.4.1.14179.1.1.1.3DisplayStringread-onlycurrent
agentInventorySerialNumber
OBJECT-TYPE
Serial number of the switch.
1.3.6.1.4.1.14179.1.1.1.4DisplayStringread-onlycurrent
agentInventoryMaintenanceLevel
OBJECT-TYPE
The switch's Inventory Maintenance Level
1.3.6.1.4.1.14179.1.1.1.6DisplayStringread-onlycurrent
agentInventoryBurnedInMacAddress
OBJECT-TYPE
Burned-In MAC Address
1.3.6.1.4.1.14179.1.1.1.9PhysAddressread-onlycurrent
agentInventoryOperatingSystem
OBJECT-TYPE
Operating System running on this unit
1.3.6.1.4.1.14179.1.1.1.10DisplayStringread-onlycurrent
agentInventoryManufacturerName
OBJECT-TYPE
Name of the switch manufacturer.
1.3.6.1.4.1.14179.1.1.1.12DisplayStringread-onlycurrent
agentInventoryProductName
OBJECT-TYPE
Name of the product.
1.3.6.1.4.1.14179.1.1.1.13DisplayStringread-onlycurrent
agentInventoryProductVersion
OBJECT-TYPE
Version of the product.
1.3.6.1.4.1.14179.1.1.1.14DisplayStringread-onlycurrent
agentInventoryIsGigECardPresent
OBJECT-TYPE
True if the Switch contains a Gigabit ethernet card .
1.3.6.1.4.1.14179.1.1.1.15TruthValueread-onlycurrent
agentInventoryIsCryptoCardPresent
OBJECT-TYPE
True if the switch is carrying a Crypto card.
1.3.6.1.4.1.14179.1.1.1.16TruthValueread-onlycurrent
agentInventoryIsForeignAPSupported
OBJECT-TYPE
States whether the switch supports third party Access Points.
1.3.6.1.4.1.14179.1.1.1.17TruthValueread-onlycurrent
agentInventoryMaxNumberOfAPsSupported
OBJECT-TYPE
Maximum number of APs supported with this Controller.
1.3.6.1.4.1.14179.1.1.1.18Integer32read-onlycurrent
agentInventoryIsCryptoCard2Present
OBJECT-TYPE
True if the switch is carrying second Crypto card for 4400 controller.
1.3.6.1.4.1.14179.1.1.1.19TruthValueread-onlycurrent
agentInventoryFipsModeEnabled
OBJECT-TYPE
True if FIPS (Federal Information Processing Standards) mode has been enabled on the controller.False if FIPS mode has not been enabled. FIPS mode can only be enabled through console.
1.3.6.1.4.1.14179.1.1.1.20TruthValueread-onlycurrent
agentTrapLogGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.2
agentTrapLogTotal
OBJECT-TYPE
The total number of traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.1Integer32read-onlycurrent
agentTrapLogTotalSinceLastViewed
OBJECT-TYPE
The number of traps sent since last viewed.
1.3.6.1.4.1.14179.1.1.2.3Integer32read-onlycurrent
agentTrapLogTable
OBJECT-TYPE
Agent Trap Log
1.3.6.1.4.1.14179.1.1.2.4not-accessiblecurrent
agentTrapLogEntry
OBJECT-TYPE
Agent trap log entry
1.3.6.1.4.1.14179.1.1.2.4.1not-accessiblecurrent
agentTrapLogIndex
OBJECT-TYPE
Unique index of trap entry
1.3.6.1.4.1.14179.1.1.2.4.1.1Integer32read-onlycurrent
agentTrapLogSystemTime
OBJECT-TYPE
System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
1.3.6.1.4.1.14179.1.1.2.4.1.2DisplayStringread-onlycurrent
agentTrapLogTrap
OBJECT-TYPE
Description of the trap sent.
1.3.6.1.4.1.14179.1.1.2.4.1.22OCTET STRING (SIZE(0..512))read-onlycurrent
agentRadioUpDownTrapCount
OBJECT-TYPE
The total number of AP Up/Down traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.5Integer32read-onlycurrent
agentApAssociateDisassociateTrapCount
OBJECT-TYPE
The total number of AP Associate/Disassociate traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.6Integer32read-onlycurrent
agentApLoadProfileFailTrapCount
OBJECT-TYPE
The total number of AP Load Profile Failure traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.7Integer32read-onlycurrent
agentApNoiseProfileFailTrapCount
OBJECT-TYPE
The total number of AP Noise Profile Failure traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.8Integer32read-onlycurrent
agentApInterferenceProfileFailTrapCount
OBJECT-TYPE
The total number of AP Interference Profile Failure traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.9Integer32read-onlycurrent
agentApCoverageProfileFailTrapCount
OBJECT-TYPE
The total number of AP Coverge Profile Failure traps sent since last reset.
1.3.6.1.4.1.14179.1.1.2.10Integer32read-onlycurrent
agentSwitchInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.3
agentSwitchInfoLwappTransportMode
OBJECT-TYPE
The LWAPP transport mode specifies if the switch is operating in Layer2 or Layer3 mode. This attribute gives the current mode the switch is operating on.
1.3.6.1.4.1.14179.1.1.3.1INTEGER {layer2(1), layer3(2)}read-onlycurrent
agentSwitchInfoPowerSupply1Present
OBJECT-TYPE
This is to indicate if the switch has Power Supply 1 present on it. This is applicable to the 4200 series and will always return true for the earlier device versions.
1.3.6.1.4.1.14179.1.1.3.2INTEGER {false(0), true(1)}read-onlycurrent
agentSwitchInfoPowerSupply1Operational
OBJECT-TYPE
This is to indicate if the switch's Power Supply 1 is operational. This is applicable to the 4200 series and will always return true for the earlier device versions.
1.3.6.1.4.1.14179.1.1.3.3INTEGER {false(0), true(1)}read-onlycurrent
agentSwitchInfoPowerSupply2Present
OBJECT-TYPE
This is to indicate if the switch has Power Supply 2 present on it. This is applicable to the 4200 series and will always return false for the earlier device versions.
1.3.6.1.4.1.14179.1.1.3.4INTEGER {false(0), true(1)}read-onlycurrent
agentSwitchInfoPowerSupply2Operational
OBJECT-TYPE
This is to indicate if the switch's Power Supply 2 is operational.This is applicable to the 4200 series and will always return false for the earlier device versions.
1.3.6.1.4.1.14179.1.1.3.5INTEGER {false(0), true(1)}read-onlycurrent
agentProductGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.4
productGroup1
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.4.1
productGroup2
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.4.2
productGroup3
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.4.3
productGroup4
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.4.4
agentResourceInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.5
agentCurrentCPUUtilization
OBJECT-TYPE
Current CPU Load of the switch in percentage.
1.3.6.1.4.1.14179.1.1.5.1INTEGER (0..100)read-onlycurrent
agentTotalMemory
OBJECT-TYPE
Total RAM of the switch in Kbytes.
1.3.6.1.4.1.14179.1.1.5.2Integer32read-onlycurrent
agentFreeMemory
OBJECT-TYPE
Free RAM of the switch in Kbytes.
1.3.6.1.4.1.14179.1.1.5.3Integer32read-onlycurrent
agentWcpInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.1.6
agentWcpDeviceName
OBJECT-TYPE
This is the name of the device this controller is residing on.
1.3.6.1.4.1.14179.1.1.6.1DisplayString (SIZE(0..32))read-onlycurrent
agentWcpSlotNumber
OBJECT-TYPE
The slot number on the Wcp Device that this controller is residing on.
1.3.6.1.4.1.14179.1.1.6.2Unsigned32 (1..16)read-onlycurrent
agentWcpPortNumber
OBJECT-TYPE
The port number on the Wcp Device that this controller is residing on.
1.3.6.1.4.1.14179.1.1.6.3Unsigned32 (1..2)read-onlycurrent
agentWcpPeerPortNumber
OBJECT-TYPE
The port number of this controller's peer on the same slot on Wcp Device that this controller is residing on.
1.3.6.1.4.1.14179.1.1.6.4Unsigned32 (1..2)read-onlycurrent
agentWcpPeerIpAddress
OBJECT-TYPE
The IP Address of this controller's peer on the same slot on Wcp Device that this controller is residing on.
1.3.6.1.4.1.14179.1.1.6.5IpAddressread-onlycurrent
agentWcpControllerTableChecksum
OBJECT-TYPE
This is the checksum that tracks the changes in the agentWcpControllerInfoTable. If there is any change in the information on this table, the checksum changes.
1.3.6.1.4.1.14179.1.1.6.6Integer32read-onlycurrent
agentWcpControllerInfoTable
OBJECT-TYPE
A table of the wireless controllers on a WCP device.
1.3.6.1.4.1.14179.1.1.6.7not-accessiblecurrent
agentWcpControllerInfoEntry
OBJECT-TYPE
Entry for a wireless controller on a WCP device.
1.3.6.1.4.1.14179.1.1.6.7.1not-accessiblecurrent
agentWcpControllerInfoSlotNumber
OBJECT-TYPE
The slot number on the Wcp device that a controller is residing on.
1.3.6.1.4.1.14179.1.1.6.7.1.1Unsigned32 (1..16)read-onlycurrent
agentWcpControllerInfoPortNumber
OBJECT-TYPE
The port number on the Wcp Device that a controller is residing on.
1.3.6.1.4.1.14179.1.1.6.7.1.2Unsigned32 (1..2)read-onlycurrent
agentWcpControllerInfoIpAddress
OBJECT-TYPE
The management IP Address of a controller.
1.3.6.1.4.1.14179.1.1.6.7.1.10IpAddressread-onlycurrent
agentConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2
agentCLIConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.1
agentLoginSessionTable
OBJECT-TYPE
A table of the switch's login session
1.3.6.1.4.1.14179.1.2.1.1not-accessiblecurrent
agentLoginSessionEntry
OBJECT-TYPE
Login Session Entry
1.3.6.1.4.1.14179.1.2.1.1.1not-accessiblecurrent
agentLoginSessionIndex
OBJECT-TYPE
Agent Login Session Index of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.1Integer32read-onlycurrent
agentLoginSessionUserName
OBJECT-TYPE
Agent Login Session UserName of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.2DisplayStringread-onlycurrent
agentLoginSessionIPAddress
OBJECT-TYPE
Agent Login Session IP Address of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.3IpAddressread-onlycurrent
agentLoginSessionConnectionType
OBJECT-TYPE
Agent Login Session Connection Type of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.4INTEGER {serial(1), telnet(2), web(3), ssl(4)}read-onlycurrent
agentLoginSessionIdleTime
OBJECT-TYPE
Agent Login Session Idle Time of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.5TimeTicksread-onlycurrent
agentLoginSessionSessionTime
OBJECT-TYPE
Agent Login Session Time of the switch
1.3.6.1.4.1.14179.1.2.1.1.1.6TimeTicksread-onlycurrent
agentLoginSessionStatus
OBJECT-TYPE
Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
1.3.6.1.4.1.14179.1.2.1.1.1.26RowStatusread-writecurrent
agentTelnetConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.1.2
agentTelnetLoginTimeout
OBJECT-TYPE
Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet session remains active indefinitely. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
1.3.6.1.4.1.14179.1.2.1.2.1Integer32 (0..160)read-writecurrent
agentTelnetMaxSessions
OBJECT-TYPE
Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
1.3.6.1.4.1.14179.1.2.1.2.2Integer32 (0..5)read-writecurrent
agentTelnetAllowNewMode
OBJECT-TYPE
Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
1.3.6.1.4.1.14179.1.2.1.2.3INTEGER {enable(1), disable(2)}read-writecurrent
agentSSHAllowNewMode
OBJECT-TYPE
Allow new SSH sessions (enable or disable) Config SSH disable means that no new SSH sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
1.3.6.1.4.1.14179.1.2.1.2.4INTEGER {enable(1), disable(2)}read-writecurrent
agentSerialGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.1.5
agentSerialTimeout
OBJECT-TYPE
Agent Serial Timeout
1.3.6.1.4.1.14179.1.2.1.5.1Integer32read-writecurrent
agentSerialBaudrate
OBJECT-TYPE
Agent Serial Baudrate
1.3.6.1.4.1.14179.1.2.1.5.2INTEGER {baud1200(1), baud2400(2), baud4800(3), baud9600(4), baud19200(5), baud38400(6), baud57600(7), baud115200(8)}read-writecurrent
agentSerialCharacterSize
OBJECT-TYPE
Agent Serial Character Size
1.3.6.1.4.1.14179.1.2.1.5.3Integer32read-onlycurrent
agentSerialHWFlowControlMode
OBJECT-TYPE
Agent Serial Hardware Flow Control.
1.3.6.1.4.1.14179.1.2.1.5.4INTEGER {enable(1), disable(2)}read-onlycurrent
agentSerialStopBits
OBJECT-TYPE
Agent Serial Stop Bits
1.3.6.1.4.1.14179.1.2.1.5.5Integer32read-onlycurrent
agentSerialParityType
OBJECT-TYPE
Agent Serial Parity Type
1.3.6.1.4.1.14179.1.2.1.5.6INTEGER {even(1), odd(2), none(3)}read-onlycurrent
agentLagConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.2
agentLagConfigCreate
OBJECT-TYPE
Agent Lag Create. When this object is set with a non-empty string, a new lag will be created.if possible with the entered string as it's name.
1.3.6.1.4.1.14179.1.2.2.1DisplayString (SIZE(1..15))read-writeobsolete
agentLagSummaryConfigTable
OBJECT-TYPE
A summary table of the switch's lag config entries
1.3.6.1.4.1.14179.1.2.2.2not-accessibleobsolete
agentLagSummaryConfigEntry
OBJECT-TYPE
Switch's lag config entry
1.3.6.1.4.1.14179.1.2.2.2.1not-accessibleobsolete
agentLagSummaryName
OBJECT-TYPE
Agent Lag Name
1.3.6.1.4.1.14179.1.2.2.2.1.1DisplayString (SIZE(1..15))read-createobsolete
agentLagSummaryLagIndex
OBJECT-TYPE
Agent Lag If Index
1.3.6.1.4.1.14179.1.2.2.2.1.2Integer32read-onlyobsolete
agentLagSummaryFlushTimer
OBJECT-TYPE
Agent Lag Flush Timer
1.3.6.1.4.1.14179.1.2.2.2.1.3Integer32read-createobsolete
agentLagSummaryLinkTrap
OBJECT-TYPE
Agent Lag Link Trap
1.3.6.1.4.1.14179.1.2.2.2.1.4INTEGER {enable(1), disable(2)}read-createobsolete
agentLagSummaryAdminMode
OBJECT-TYPE
Agent Lag Admin Mode
1.3.6.1.4.1.14179.1.2.2.2.1.5INTEGER {enable(1), disable(2)}read-createobsolete
agentLagSummaryStpMode
OBJECT-TYPE
Agent Lag STP Mode
1.3.6.1.4.1.14179.1.2.2.2.1.6INTEGER {dot1d(1), fast(2), off(3)}read-createobsolete
agentLagSummaryAddPort
OBJECT-TYPE
Agent Lag Add Port. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
1.3.6.1.4.1.14179.1.2.2.2.1.7Integer32read-createobsolete
agentLagSummaryDeletePort
OBJECT-TYPE
Agent Lag Delete Port
1.3.6.1.4.1.14179.1.2.2.2.1.8Integer32read-createobsolete
agentLagSummaryPortsBitMask
OBJECT-TYPE
Agent Lag Member Ports in bit mask representation
1.3.6.1.4.1.14179.1.2.2.2.1.9Unsigned32read-createobsolete
agentLagSummaryStatus
OBJECT-TYPE
Agent Lag Status. active(1) - This Lag is enabled. destroy(6) - Set to this value to remove the Lag.
1.3.6.1.4.1.14179.1.2.2.2.1.30RowStatusread-createobsolete
agentLagDetailedConfigTable
OBJECT-TYPE
A detailed table of the switch's lag config entries
1.3.6.1.4.1.14179.1.2.2.3not-accessibleobsolete
agentLagDetailedConfigEntry
OBJECT-TYPE
Switch's lag config entry
1.3.6.1.4.1.14179.1.2.2.3.1not-accessibleobsolete
agentLagDetailedLagIndex
OBJECT-TYPE
Lag index
1.3.6.1.4.1.14179.1.2.2.3.1.1Integer32read-onlyobsolete
agentLagDetailedIfIndex
OBJECT-TYPE
Lag port index
1.3.6.1.4.1.14179.1.2.2.3.1.2Integer32read-onlyobsolete
agentLagDetailedPortSpeed
OBJECT-TYPE
Lag port speed. See agentPortType for description and list of valid values.
1.3.6.1.4.1.14179.1.2.2.3.1.22OBJECT IDENTIFIERread-onlyobsolete
agentLagConfigMode
OBJECT-TYPE
The Lag Mode on the 4400 series controller. When it is on, all the gigabit ports are bound to one aggregated link.
1.3.6.1.4.1.14179.1.2.2.4INTEGER {off(1), on(2)}read-writeobsolete
agentNetworkConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.3
agentNetworkIPAddress
OBJECT-TYPE
The switch's network ip address
1.3.6.1.4.1.14179.1.2.3.1IpAddressread-writecurrent
agentNetworkSubnetMask
OBJECT-TYPE
The switch's network subnet mask
1.3.6.1.4.1.14179.1.2.3.2IpAddressread-writecurrent
agentNetworkDefaultGateway
OBJECT-TYPE
The switch's network default gateway
1.3.6.1.4.1.14179.1.2.3.3IpAddressread-writecurrent
agentNetworkBurnedInMacAddress
OBJECT-TYPE
The switch's Burned-In MAC address
1.3.6.1.4.1.14179.1.2.3.4PhysAddressread-onlycurrent
agentNetworkConfigProtocol
OBJECT-TYPE
The switch's network config protocol
1.3.6.1.4.1.14179.1.2.3.7INTEGER {none(1), bootp(2), dhcp(3)}read-writecurrent
agentNetworkWebMode
OBJECT-TYPE
The switch's web access mode.
1.3.6.1.4.1.14179.1.2.3.8INTEGER {enable(1), disable(2)}read-writecurrent
agentNetworkSecureWebMode
OBJECT-TYPE
If https is enable or not provided web mode is enabled
1.3.6.1.4.1.14179.1.2.3.9INTEGER {disable(0), enable(1)}read-writecurrent
agentNetworkMulticastMode
OBJECT-TYPE
Switch's ethernet multicast support. disable- multicast is disabled multicast - Multicast is enabled. unicast- Controller will convert multicast to unicast packet.
1.3.6.1.4.1.14179.1.2.3.10INTEGER {disable(0), unicast(1), multicast(2)}read-writecurrent
agentNetworkDsPortNumber
OBJECT-TYPE
The switch's distribution port number.
1.3.6.1.4.1.14179.1.2.3.11Integer32read-writecurrent
agentNetworkUserIdleTimeout
OBJECT-TYPE
Sets the idle user timeout.
1.3.6.1.4.1.14179.1.2.3.12Unsigned32 (10..2147483647)read-writecurrent
agentNetworkArpTimeout
OBJECT-TYPE
Sets the ARP entry timeout.
1.3.6.1.4.1.14179.1.2.3.13Unsigned32 (10..2147483647)read-writecurrent
agentNetworkManagementVlan
OBJECT-TYPE
VLAN ID of the network management interface.
1.3.6.1.4.1.14179.1.2.3.14Unsigned32 (0..4095)read-writecurrent
agentNetworkGvrpStatus
OBJECT-TYPE
The state of GVRP operation on the Switch. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute No longer supported)
1.3.6.1.4.1.14179.1.2.3.15INTEGER {disabled(0), enabled(1)}read-writeobsolete
agentNetworkAllowMgmtViaWireless
OBJECT-TYPE
This states whether Management via wireless is allowed or not.
1.3.6.1.4.1.14179.1.2.3.16INTEGER {disable(0), enable(1)}read-writecurrent
agentNetworkBroadcastSsidMode
OBJECT-TYPE
This mode when enabled allows WLAN SSIDs to be broadcasted.
1.3.6.1.4.1.14179.1.2.3.17INTEGER {disable(0), enable(1)}read-writecurrent
agentNetworkSecureWebPassword
OBJECT-TYPE
SSL Certificate Password. This can be optionally set while downloading SSL certificates of type Web Admin and Web Authentication
1.3.6.1.4.1.14179.1.2.3.18OCTET STRING (SIZE(1..32))read-writecurrent
agentNetworkWebAdminCertType
OBJECT-TYPE
Type of currently existing Web Admin Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.
1.3.6.1.4.1.14179.1.2.3.19DisplayString (SIZE(1..80))read-onlycurrent
agentNetworkWebAdminCertRegenerateCmdInvoke
OBJECT-TYPE
This command when set to 'activate' will regenerate a Web Administration Certificate Locally that will replace the existing certificate.
1.3.6.1.4.1.14179.1.2.3.20INTEGER {default(0), activate(1)}read-writecurrent
agentNetworkWebAuthCertType
OBJECT-TYPE
Type of currently exisitng Web Authentication Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.
1.3.6.1.4.1.14179.1.2.3.21DisplayString (SIZE(1..80))read-onlycurrent
agentNetworkWebAuthCertRegenerateCmdInvoke
OBJECT-TYPE
This command when set to 'activate' will regenerate a Web Authentication Certificate Locally that will replace the existing certificate.
1.3.6.1.4.1.14179.1.2.3.22INTEGER {default(0), activate(1)}read-writecurrent
agentNetworkRouteConfigTable
OBJECT-TYPE
A table of the switch's Network Route entries
1.3.6.1.4.1.14179.1.2.3.23not-accessiblecurrent
agentNetworkRouteConfigEntry
OBJECT-TYPE
Switch's Network Route entry
1.3.6.1.4.1.14179.1.2.3.23.1not-accessiblecurrent
agentNetworkRouteIPAddress
OBJECT-TYPE
Network Route IP Address.
1.3.6.1.4.1.14179.1.2.3.23.1.1IpAddressread-createcurrent
agentNetworkRouteIPNetmask
OBJECT-TYPE
Network Route IP Netmask.
1.3.6.1.4.1.14179.1.2.3.23.1.2IpAddressread-createcurrent
agentNetworkRouteGateway
OBJECT-TYPE
Network Route IP Gateway.
1.3.6.1.4.1.14179.1.2.3.23.1.3IpAddressread-createcurrent
agentNetworkRouteStatus
OBJECT-TYPE
Network Route Row Status.
1.3.6.1.4.1.14179.1.2.3.23.1.23RowStatusread-createcurrent
agentNetworkPeerToPeerBlockingMode
OBJECT-TYPE
Mobile Peer to Peer Blocking mode on the switch.
1.3.6.1.4.1.14179.1.2.3.24INTEGER {disable(0), enable(1)}read-writecurrent
agentNetworkMulticastGroupAddress
OBJECT-TYPE
Multicast group address for access points.
1.3.6.1.4.1.14179.1.2.3.25IpAddressread-writecurrent
agentServicePortConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.4
agentServicePortIPAddress
OBJECT-TYPE
The switch's Service Port IP address. (Service-port interface use is recommended instead of this group)
1.3.6.1.4.1.14179.1.2.4.1IpAddressread-writeobsolete
agentServicePortSubnetMask
OBJECT-TYPE
The switch's Service Port subnet mask. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
1.3.6.1.4.1.14179.1.2.4.2IpAddressread-writeobsolete
agentServicePortDefaultGateway
OBJECT-TYPE
Not Supported for release 1.0. The switch's Service Port default gateway. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
1.3.6.1.4.1.14179.1.2.4.3IpAddressread-writeobsolete
agentServicePortBurnedInMacAddress
OBJECT-TYPE
The switch's Service Port Burned-In MAC address (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
1.3.6.1.4.1.14179.1.2.4.4PhysAddressread-onlyobsolete
agentServicePortConfigProtocol
OBJECT-TYPE
The switch's Service Port config protocol (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)
1.3.6.1.4.1.14179.1.2.4.5INTEGER {none(1), dhcp(3)}read-writeobsolete
agentSnmpConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.5
agentSnmpTrapPortNumber
OBJECT-TYPE
Snmp Trap Port Number
1.3.6.1.4.1.14179.1.2.5.1Unsigned32 (1..65534)read-writecurrent
agentSnmpVersion1Status
OBJECT-TYPE
Snmp Version 1 Status
1.3.6.1.4.1.14179.1.2.5.2INTEGER {disable(0), enable(1)}read-writecurrent
agentSnmpVersion2cStatus
OBJECT-TYPE
Snmp Version 2c Status
1.3.6.1.4.1.14179.1.2.5.3INTEGER {disable(0), enable(1)}read-writecurrent
agentSnmpCommunityConfigTable
OBJECT-TYPE
A table of the switch's SNMP community Config entries
1.3.6.1.4.1.14179.1.2.5.5not-accessiblecurrent
agentSnmpCommunityConfigEntry
OBJECT-TYPE
Switch's SNMP community Config entry
1.3.6.1.4.1.14179.1.2.5.5.1not-accessiblecurrent
agentSnmpCommunityName
OBJECT-TYPE
The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.
1.3.6.1.4.1.14179.1.2.5.5.1.1DisplayString (SIZE(1..16))read-createcurrent
agentSnmpCommunityIPAddress
OBJECT-TYPE
The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.
1.3.6.1.4.1.14179.1.2.5.5.1.2IpAddressread-createcurrent
agentSnmpCommunityIPMask
OBJECT-TYPE
The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.
1.3.6.1.4.1.14179.1.2.5.5.1.3IpAddressread-createcurrent
agentSnmpCommunityAccessMode
OBJECT-TYPE
The switch's Snmp Community Access Mode Access Mode - This value can be readOnly or readWrite. A community with a read-only access allows for switch information to be displayed. A community with a readWrite access allows for configuration changes to be made and for information to be displayed.
1.3.6.1.4.1.14179.1.2.5.5.1.4INTEGER {readOnly(1), readWrite(2)}read-createcurrent
agentSnmpCommunityEnabled
OBJECT-TYPE
If community is Enabled
1.3.6.1.4.1.14179.1.2.5.5.1.5INTEGER {no(0), yes(1)}read-createcurrent
agentSnmpCommunityStatus
OBJECT-TYPE
The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP manager associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.
1.3.6.1.4.1.14179.1.2.5.5.1.25RowStatusread-createcurrent
agentSnmpTrapReceiverConfigTable
OBJECT-TYPE
Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.
1.3.6.1.4.1.14179.1.2.5.6not-accessiblecurrent
agentSnmpTrapReceiverConfigEntry
OBJECT-TYPE
Switch's Snmp Trap Receiver Config entry
1.3.6.1.4.1.14179.1.2.5.6.1not-accessiblecurrent
agentSnmpTrapReceiverName
OBJECT-TYPE
The switch's Snmp Trap Receiver Name. This is the name of the remote network manager. the name can be up to 16 characters, and is case-sensitive.
1.3.6.1.4.1.14179.1.2.5.6.1.1OCTET STRING (SIZE(1..16))read-createcurrent
agentSnmpTrapReceiverIPAddress
OBJECT-TYPE
SNMP network Manager IP Address. The IP Address traps will be sent to. Each IP address parameter is four integer numbers. The numbers range from 0 to 255. After creation of entry IP Address cannot be changed.
1.3.6.1.4.1.14179.1.2.5.6.1.2IpAddressread-createcurrent
agentSnmpTrapReceiverEnabled
OBJECT-TYPE
The flag to enable the trap receiver. If disabled, no traps are sent to this receiver's IP Address.
1.3.6.1.4.1.14179.1.2.5.6.1.3INTEGER {no(0), yes(1)}read-createcurrent
agentSnmpTrapReceiverStatus
OBJECT-TYPE
This object is used to create and delete instances of this table. The row, when created with the row status value of 'createAndGo' or 'createAndWait' is moved to the 'active' state automatically by the agent and remains in that state till the time the row is removed through the 'destroy' option.
1.3.6.1.4.1.14179.1.2.5.6.1.23RowStatusread-createcurrent
agentSnmpTrapFlagsConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.5.7
agentSnmpAuthenticationTrapFlag
OBJECT-TYPE
Authentication Flag - Enable/Disable authentication Flag.
1.3.6.1.4.1.14179.1.2.5.7.1INTEGER {enable(1), disable(2)}read-writecurrent
agentSnmpLinkUpDownTrapFlag
OBJECT-TYPE
Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.
1.3.6.1.4.1.14179.1.2.5.7.2INTEGER {enable(1), disable(2)}read-writecurrent
agentSnmpMultipleUsersTrapFlag
OBJECT-TYPE
Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session
1.3.6.1.4.1.14179.1.2.5.7.3INTEGER {enable(1), disable(2)}read-writecurrent
agentSnmpSpanningTreeTrapFlag
OBJECT-TYPE
Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.
1.3.6.1.4.1.14179.1.2.5.7.4INTEGER {enable(1), disable(2)}read-writecurrent
agentSnmpBroadcastStormTrapFlag
OBJECT-TYPE
Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.
1.3.6.1.4.1.14179.1.2.5.7.5INTEGER {enable(1), disable(2)}read-writeobsolete
agentSnmpV3ConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.6
agentSnmpVersion3Status
OBJECT-TYPE
Snmp Version 3 Status
1.3.6.1.4.1.14179.1.2.6.1INTEGER {disable(0), enable(1)}read-writecurrent
agentSnmpV3UserConfigTable
OBJECT-TYPE
User Config Table. Only creation and deletion of users is supported. All individual updates are not supported.
1.3.6.1.4.1.14179.1.2.6.2not-accessiblecurrent
agentSnmpV3UserConfigEntry
OBJECT-TYPE
User Config Entry
1.3.6.1.4.1.14179.1.2.6.2.1not-accessiblecurrent
agentSnmpV3UserName
OBJECT-TYPE
Agent User Name.
1.3.6.1.4.1.14179.1.2.6.2.1.1OCTET STRING (SIZE(1..32))read-createcurrent
agentSnmpV3UserAccessMode
OBJECT-TYPE
Agent User Access Mode
1.3.6.1.4.1.14179.1.2.6.2.1.2INTEGER {readonly(1), readwrite(2)}read-createcurrent
agentSnmpV3UserAuthenticationType
OBJECT-TYPE
SNMPv3 User Authentication none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
1.3.6.1.4.1.14179.1.2.6.2.1.3INTEGER {none(1), hmacmd5(2), hmacsha(3)}read-createcurrent
agentSnmpV3UserEncryptionType
OBJECT-TYPE
SNMPv3 User Encryption Must be set to none(1) if agentSnmpV3UserAuthenticationType is set to none(1). Setting this object will set the encryption password to an empty string. none(1) - no encryption used des(1) - DES encryption used
1.3.6.1.4.1.14179.1.2.6.2.1.4INTEGER {none(1), des(2)}read-createcurrent
agentSnmpV3UserAuthenticationPassword
OBJECT-TYPE
SNMPv3 User Encryption Password
1.3.6.1.4.1.14179.1.2.6.2.1.5OCTET STRING (SIZE(0..32))read-createcurrent
agentSnmpV3UserEncryptionPassword
OBJECT-TYPE
SNMPv3 User Encryption Password
1.3.6.1.4.1.14179.1.2.6.2.1.6OCTET STRING (SIZE(0..32))read-createcurrent
agentSnmpV3UserStatus
OBJECT-TYPE
Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
1.3.6.1.4.1.14179.1.2.6.2.1.26RowStatusread-createcurrent
agentSpanningTreeConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.7
agentSpanningTreeMode
OBJECT-TYPE
The switch's Spanning Tree Switch Status
1.3.6.1.4.1.14179.1.2.7.1INTEGER {enable(1), disable(2)}read-writecurrent
agentSwitchConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.8
agentSwitchBroadcastControlMode
OBJECT-TYPE
The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less.Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
1.3.6.1.4.1.14179.1.2.8.2INTEGER {enable(1), disable(2)}read-writecurrent
agentSwitchDot3FlowControlMode
OBJECT-TYPE
Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
1.3.6.1.4.1.14179.1.2.8.3INTEGER {enable(1), disable(2)}read-writecurrent
agentSwitchAddressAgingTimeoutTable
OBJECT-TYPE
The switch's address aging timeout table
1.3.6.1.4.1.14179.1.2.8.4not-accessiblecurrent
agentSwitchAddressAgingTimeoutEntry
OBJECT-TYPE
Aging information about a specific Filtering Database.
1.3.6.1.4.1.14179.1.2.8.4.1not-accessiblecurrent
agentSwitchAddressAgingTimeout
OBJECT-TYPE
The FDB entry's address aging timeout(in seconds)
1.3.6.1.4.1.14179.1.2.8.4.1.10Integer32 (10..1000000)read-writecurrent
agentSwitchLwappTransportMode
OBJECT-TYPE
The LWAPP transport mode decides if the switch is operating in the Layer2 or Layer3 mode. The switch needs to be rebooted for the mode change to take effect.
1.3.6.1.4.1.14179.1.2.8.5INTEGER {layer2(1), layer3(2)}read-writecurrent
agentTransferConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.9
agentTransferUploadGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.9.1
agentTransferUploadMode
OBJECT-TYPE
Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
1.3.6.1.4.1.14179.1.2.9.1.1INTEGER {tftp(1), xmodem(2), ymodem(3), zmodem(4)}read-writecurrent
agentTransferUploadServerIP
OBJECT-TYPE
Transfer upload tftpserverip configures the IP address of the server where the file will be uploaded. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
1.3.6.1.4.1.14179.1.2.9.1.2IpAddressread-writecurrent
agentTransferUploadPath
OBJECT-TYPE
Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
1.3.6.1.4.1.14179.1.2.9.1.3DisplayString (SIZE(0..63))read-writecurrent
agentTransferUploadFilename
OBJECT-TYPE
Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
1.3.6.1.4.1.14179.1.2.9.1.4DisplayString (SIZE(0..63))read-writecurrent
agentTransferUploadDataType
OBJECT-TYPE
Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - System trace - Trap log - Crash File
1.3.6.1.4.1.14179.1.2.9.1.5INTEGER {config(2), errorlog(3), systemtrace(4), traplog(5), crashfile(6), signatures(7), unknown(99)}read-writecurrent
agentTransferUploadStart
OBJECT-TYPE
Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
1.3.6.1.4.1.14179.1.2.9.1.6INTEGER {enable(1), disable(2)}read-writecurrent
agentTransferUploadStatus
OBJECT-TYPE
Indicates the current status of an upload transfer.
1.3.6.1.4.1.14179.1.2.9.1.7INTEGER {notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), unknown(99)}read-onlycurrent
agentTransferDownloadGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.9.2
agentTransferDownloadMode
OBJECT-TYPE
Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
1.3.6.1.4.1.14179.1.2.9.2.1INTEGER {tftp(1), xmodem(2), ymodem(3), zmodem(4)}read-writecurrent
agentTransferDownloadServerIP
OBJECT-TYPE
Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
1.3.6.1.4.1.14179.1.2.9.2.2IpAddressread-writecurrent
agentTransferDownloadPath
OBJECT-TYPE
Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
1.3.6.1.4.1.14179.1.2.9.2.3DisplayString (SIZE(0..63))read-writecurrent
agentTransferDownloadFilename
OBJECT-TYPE
Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
1.3.6.1.4.1.14179.1.2.9.2.4DisplayString (SIZE(0..63))read-writecurrent
agentTransferDownloadDataType
OBJECT-TYPE
Transfer download datatype configures the type of file to downloaded to the switch. The types for download are: - Code - Configuration - Certificates - Signatures - customWebauth- custom webauth tar ball
1.3.6.1.4.1.14179.1.2.9.2.5INTEGER {code(2), config(3), webauthcert(4), webadmincert(5), signatures(6), customWebAuth(7), unknown(99)}read-writecurrent
agentTransferDownloadStart
OBJECT-TYPE
Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
1.3.6.1.4.1.14179.1.2.9.2.6INTEGER {enable(1), disable(2)}read-writecurrent
agentTransferDownloadStatus
OBJECT-TYPE
Indicates the current status of an download transfer.
1.3.6.1.4.1.14179.1.2.9.2.7INTEGER {notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), bootBreakOff(14), invalidTarFile(15), unknown(99)}read-onlycurrent
agentTransferDownloadTftpMaxRetries
OBJECT-TYPE
Maximum number of retries to be allowed for a TFTP message packet.
1.3.6.1.4.1.14179.1.2.9.2.8Unsigned32 (1..254)read-writecurrent
agentTransferDownloadTftpTimeout
OBJECT-TYPE
Timeout in seconds for a TFTP message packet.
1.3.6.1.4.1.14179.1.2.9.2.9Unsigned32 (1..254)read-writecurrent
agentTransferConfigurationFileEncryption
OBJECT-TYPE
The configuration file can be encrypted before tftp upload from the switch and then decrypted before downloading to the switch when this option is enabled.
1.3.6.1.4.1.14179.1.2.9.3INTEGER {disable(0), enable(1)}read-writecurrent
agentTransferConfigurationFileEncryptionKey
OBJECT-TYPE
This is the key to be used when encrypting the configuration file while upload from the switch or while decrypting the file after download to the switch.
1.3.6.1.4.1.14179.1.2.9.4DisplayString (SIZE(0..16))read-writecurrent
agentDot3adAggPortTable
OBJECT-TYPE
This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
1.3.6.1.4.1.14179.1.2.11not-accessibleobsolete
agentDot3adAggPortEntry
OBJECT-TYPE
Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.
1.3.6.1.4.1.14179.1.2.11.1not-accessibleobsolete
agentDot3adAggPort
OBJECT-TYPE
ifIndex of this physical port
1.3.6.1.4.1.14179.1.2.11.1.1Integer32read-onlyobsolete
agentDot3adAggPortLACPMode
OBJECT-TYPE
Enable/disable 802.3ad LACP on this port
1.3.6.1.4.1.14179.1.2.11.1.21INTEGER {enable(1), disable(2)}read-writeobsolete
agentPortConfigTable
OBJECT-TYPE
A table of the switch's physical port config entries
1.3.6.1.4.1.14179.1.2.12not-accessiblecurrent
agentPortConfigEntry
OBJECT-TYPE
Switch's physical port config entry
1.3.6.1.4.1.14179.1.2.12.1not-accessiblecurrent
agentPortDot1dBasePort
OBJECT-TYPE
The port number of this port.
1.3.6.1.4.1.14179.1.2.12.1.1Integer32 (1..65535)read-onlycurrent
agentPortIfIndex
OBJECT-TYPE
The switch's Port IfIndex
1.3.6.1.4.1.14179.1.2.12.1.2Integer32read-onlycurrent
agentPortIanaType
OBJECT-TYPE
The switch's Port Type
1.3.6.1.4.1.14179.1.2.12.1.3IANAifTyperead-onlycurrent
agentPortSTPMode
OBJECT-TYPE
The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port
1.3.6.1.4.1.14179.1.2.12.1.4INTEGER {dot1d(1), fast(2), off(3)}read-writecurrent
agentPortSTPState
OBJECT-TYPE
The switch's Port Spanning Tree Protocol State
1.3.6.1.4.1.14179.1.2.12.1.5INTEGER {blocking(1), listening(2), learning(3), forwarding(4), disabled(5)}read-onlycurrent
agentPortAdminMode
OBJECT-TYPE
The switch's Port Admin Mode
1.3.6.1.4.1.14179.1.2.12.1.6INTEGER {enable(1), disable(2)}read-writecurrent
agentPortPhysicalMode
OBJECT-TYPE
The switch's Port Speed Mode. This is the configured physical mode.This object is read-only for gigabit ports
1.3.6.1.4.1.14179.1.2.12.1.7INTEGER {autoNegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(8)}read-writecurrent
agentPortPhysicalStatus
OBJECT-TYPE
The switch's Port Physical Speed Status.This is the current actual speed.
1.3.6.1.4.1.14179.1.2.12.1.8INTEGER {autonegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(8), unknown(9)}read-onlycurrent
agentPortLinkTrapMode
OBJECT-TYPE
If enabled, link up and link down traps will be sent for this port.
1.3.6.1.4.1.14179.1.2.12.1.9INTEGER {enable(1), disable(2)}read-writecurrent
agentPortClearStats
OBJECT-TYPE
Clear stats for this port only
1.3.6.1.4.1.14179.1.2.12.1.10INTEGER {enable(1), disable(2)}read-writecurrent
agentPortDefaultType
OBJECT-TYPE
This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively- configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
1.3.6.1.4.1.14179.1.2.12.1.11OBJECT IDENTIFIERread-writecurrent
agentPortType
OBJECT-TYPE
This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object qbEnetDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object qbEnetPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
1.3.6.1.4.1.14179.1.2.12.1.12OBJECT IDENTIFIERread-onlycurrent
agentPortAutoNegAdminStatus
OBJECT-TYPE
This object identifies the administration status of auto negotiation for this port.
1.3.6.1.4.1.14179.1.2.12.1.13INTEGER {enable(1), disable(2)}read-writecurrent
agentPortDot3FlowControlMode
OBJECT-TYPE
Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
1.3.6.1.4.1.14179.1.2.12.1.14INTEGER {enable(1), disable(2)}read-writecurrent
agentPortPowerMode
OBJECT-TYPE
Enable/Disable the port's Power over ethernet. This doesn't apply to appliances that have no POE controller.
1.3.6.1.4.1.14179.1.2.12.1.15INTEGER {disable(0), enable(1)}read-writecurrent
agentPortGvrpStatus
OBJECT-TYPE
The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.(Attribute no longer supported)
1.3.6.1.4.1.14179.1.2.12.1.16INTEGER {enabled(1), disabled(2)}read-writeobsolete
agentPortGarpJoinTime
OBJECT-TYPE
The GARP Join time, in centiseconds.(Attribute no longer supported)
1.3.6.1.4.1.14179.1.2.12.1.17Unsigned32read-writeobsolete
agentPortGarpLeaveTime
OBJECT-TYPE
The GARP Leave time, in centiseconds.(Attribute no longer supported)
1.3.6.1.4.1.14179.1.2.12.1.18Unsigned32read-writeobsolete
agentPortGarpLeaveAllTime
OBJECT-TYPE
The GARP LeaveAll time, in centiseconds.(Attribute no longer supported)
1.3.6.1.4.1.14179.1.2.12.1.19Unsigned32read-writeobsolete
agentPortMirrorMode
OBJECT-TYPE
The switch's Port Mirror Mode. If enabled, then this is the port that the packets are mirrored to.
1.3.6.1.4.1.14179.1.2.12.1.20INTEGER {disable(0), enable(1)}read-writecurrent
agentPortMulticastApplianceMode
OBJECT-TYPE
The Port Multicast Appliance Mode. If enabled, then this port allows multicast streams through it. At a time, a maximum of four ports including the gigabit ethernet port can have this mode enabled on them. This is to limit the number of multicast streams allowed through the switch at a given time.
1.3.6.1.4.1.14179.1.2.12.1.21INTEGER {disable(0), enable(1)}read-writecurrent
agentPortOperationalStatus
OBJECT-TYPE
The current operational state of the port.
1.3.6.1.4.1.14179.1.2.12.1.40INTEGER {up(1), down(2)}read-onlycurrent
agentInterfaceConfigTable
OBJECT-TYPE
A table of the switch's Interface Config entries Typically, it will contain entries for Service Port Interface, DS Port Interface and Virtual Gateway Interface apart from other entries.
1.3.6.1.4.1.14179.1.2.13not-accessiblecurrent
agentInterfaceConfigEntry
OBJECT-TYPE
Switch's Interface Config entry
1.3.6.1.4.1.14179.1.2.13.1not-accessiblecurrent
agentInterfaceName
OBJECT-TYPE
Interace Name. This values is 'management' for DS port, 'service-port' for service port and 'virtual' for virtual gateway. For other interfaces, the name can be anything. These interfaces are already created by default.
1.3.6.1.4.1.14179.1.2.13.1.1OCTET STRING (SIZE(1..32))read-createcurrent
agentInterfaceVlanId
OBJECT-TYPE
Vlan ID configured for the Interface.
1.3.6.1.4.1.14179.1.2.13.1.2Integer32 (0..4094)read-createcurrent
agentInterfaceType
OBJECT-TYPE
The interface's type. The static type is set for the interfaces that are created by default on the switch and these cannot be deleted. Any other interface that is created is of type dynamic which can be deleted.
1.3.6.1.4.1.14179.1.2.13.1.3INTEGER {static(0), dynamic(1)}read-onlycurrent
agentInterfaceMacAddress
OBJECT-TYPE
Interface MAC Address. This is only applicable in case of management and service-port interfaces.
1.3.6.1.4.1.14179.1.2.13.1.4MacAddressread-onlycurrent
agentInterfaceIPAddress
OBJECT-TYPE
IP Address of the interface.
1.3.6.1.4.1.14179.1.2.13.1.5IpAddressread-createcurrent
agentInterfaceIPNetmask
OBJECT-TYPE
IP Netmask of the interface. This is 0 for the virtual interface.
1.3.6.1.4.1.14179.1.2.13.1.6IpAddressread-createcurrent
agentInterfaceIPGateway
OBJECT-TYPE
IP Gateway of the interface. This is 0 for virtual and service-port interface.
1.3.6.1.4.1.14179.1.2.13.1.7IpAddressread-createcurrent
agentInterfacePortNo
OBJECT-TYPE
A value 0 means the port is not set. The valid value can be any one of the physical ports on the switch. This is the primary port configured on the interface.
1.3.6.1.4.1.14179.1.2.13.1.8Integer32 (0..25)read-createcurrent
agentInterfacePrimaryDhcpAddress
OBJECT-TYPE
Primary DHCP Server IP Address for the interface This applies to the management interface and other dynamic interfaces.
1.3.6.1.4.1.14179.1.2.13.1.9IpAddressread-createcurrent
agentInterfaceSecondaryDhcpAddress
OBJECT-TYPE
Secondary DHCP Server IP Address for the interface. This applies to the management interface and other dynamic interfaces.
1.3.6.1.4.1.14179.1.2.13.1.10IpAddressread-createcurrent
agentInterfaceDhcpProtocol
OBJECT-TYPE
The interface's DHCP protocol. This applies only to the service port interface.
1.3.6.1.4.1.14179.1.2.13.1.11INTEGER {disabled(0), enabled(1)}read-createcurrent
agentInterfaceDnsHostName
OBJECT-TYPE
The DNS host name for the Virtual Interface. This attribute is not valid for other interfaces.
1.3.6.1.4.1.14179.1.2.13.1.12DisplayString (SIZE(0..80))read-createcurrent
agentInterfaceAclName
OBJECT-TYPE
Name of the Access Control List applied to the interface. This attribute is applicable only to the management interface and other dynamic interfaces. If it is required to remove the ACL name for an interface, it should be set to an empty string.
1.3.6.1.4.1.14179.1.2.13.1.13DisplayString (SIZE(0..32))read-createcurrent
agentInterfaceAPManagementFeature
OBJECT-TYPE
When enabled, the dynamic interface can be used for AP management. SNMP support for AP management through dynamic interfaces has been introduced since '3.0.21.0' release. Only applicable to dynamic interfaces in 4200 series. In static interfaces, 'disable' value 0 is returned. In 4000/3500 series of switches, 'disable' value 0 is returned.
1.3.6.1.4.1.14179.1.2.13.1.14INTEGER {disable(0), enable(1)}read-createcurrent
agentInterfaceActivePortNo
OBJECT-TYPE
This is the currently active port for this interface.
1.3.6.1.4.1.14179.1.2.13.1.15Integer32 (0..25)read-onlycurrent
agentInterfaceBackupPortNo
OBJECT-TYPE
This values is valid only for the 4200 series of switches. The backup port is the port this interface is moved to once the primary port fails. A value 0 means the port is not set. The valid value can be any one of the physical ports on the 4200 switch.
1.3.6.1.4.1.14179.1.2.13.1.16Integer32 (0..4)read-createcurrent
agentInterfaceVlanQuarantine
OBJECT-TYPE
This object is used to configure the health of the interface identified by agentInterfaceName. A value of 'true' is used to indicate that this particular interface is unhealthy. In this case, the data packets of the clients, that are assigned the VLAN Id corresponding to this interface, must be tunneled to the Controller by the REAP AP. A value of 'false' indicates that the VLAN configured against the interface is healthy and that the REAP AP can switch the clients of this VLAN locally rather than tunneling them to the Controller.
1.3.6.1.4.1.14179.1.2.13.1.17TruthValueread-createcurrent
agentInterfaceRowStatus
OBJECT-TYPE
The interface entry Row status.
1.3.6.1.4.1.14179.1.2.13.1.31RowStatusread-createcurrent
agentNtpConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.14
agentNtpPollingInterval
OBJECT-TYPE
Network Time Protocol polling interval. Min value is one hour and maximum is a week.
1.3.6.1.4.1.14179.1.2.14.1Integer32 (3600..604800)read-writecurrent
agentNtpServerTable
OBJECT-TYPE
A summary table for switch's lag config entries
1.3.6.1.4.1.14179.1.2.14.2not-accessiblecurrent
agentNtpServerEntry
OBJECT-TYPE
Switch's NTP Server entry. Upto 4 entries may be added.
1.3.6.1.4.1.14179.1.2.14.2.1not-accessiblecurrent
agentNtpServerIndex
OBJECT-TYPE
NTP Server priority index.
1.3.6.1.4.1.14179.1.2.14.2.1.1Integer32 (1..3)read-createcurrent
agentNtpServerAddress
OBJECT-TYPE
IP Address of the NTP Server
1.3.6.1.4.1.14179.1.2.14.2.1.2IpAddressread-createcurrent
agentNtpServerRowStatus
OBJECT-TYPE
NTP server entry row status.
1.3.6.1.4.1.14179.1.2.14.2.1.20RowStatusread-createcurrent
agentDhcpConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.2.15
agentDhcpScopeTable
OBJECT-TYPE
A table listing the Scopes defined on the switch's DHCP Server.
1.3.6.1.4.1.14179.1.2.15.1not-accessiblecurrent
agentDhcpScopeEntry
OBJECT-TYPE
Switch's DHCP Server Scope entry.
1.3.6.1.4.1.14179.1.2.15.1.1not-accessiblecurrent
agentDhcpScopeIndex
OBJECT-TYPE
DHCP Scope Identifier Index.
1.3.6.1.4.1.14179.1.2.15.1.1.1Unsigned32 (0..15)read-createcurrent
agentDhcpScopeName
OBJECT-TYPE
DHCP Scope Name.
1.3.6.1.4.1.14179.1.2.15.1.1.2DisplayString (SIZE(1..79))read-createcurrent
agentDhcpScopeLeaseTime
OBJECT-TYPE
DHCP Scope Lease time in seconds.
1.3.6.1.4.1.14179.1.2.15.1.1.3Integer32 (120..8640000)read-createcurrent
agentDhcpScopeNetwork
OBJECT-TYPE
IP Address of the DHCP Scope Network. This is the address which is used to determine the DHCP scope a remote Switch is attaching to.
1.3.6.1.4.1.14179.1.2.15.1.1.4IpAddressread-createcurrent
agentDhcpScopeNetmask
OBJECT-TYPE
The DHCP Scope Netmask. This the subnet mask for the address pool.
1.3.6.1.4.1.14179.1.2.15.1.1.5IpAddressread-createcurrent
agentDhcpScopePoolStartAddress
OBJECT-TYPE
The DHCP Scope address pool start IP address.
1.3.6.1.4.1.14179.1.2.15.1.1.6IpAddressread-createcurrent
agentDhcpScopePoolEndAddress
OBJECT-TYPE
The DHCP Scope address pool end IP address.
1.3.6.1.4.1.14179.1.2.15.1.1.7IpAddressread-createcurrent
agentDhcpScopeDefaultRouterAddress1
OBJECT-TYPE
IP Address of the DHCP Scope's default Router 1.
1.3.6.1.4.1.14179.1.2.15.1.1.8IpAddressread-createcurrent
agentDhcpScopeDefaultRouterAddress2
OBJECT-TYPE
IP Address of the DHCP Scope's default Router 2.
1.3.6.1.4.1.14179.1.2.15.1.1.9IpAddressread-createcurrent
agentDhcpScopeDefaultRouterAddress3
OBJECT-TYPE
IP Address of the DHCP Scope's default Router 3.
1.3.6.1.4.1.14179.1.2.15.1.1.10IpAddressread-createcurrent
agentDhcpScopeDnsDomainName
OBJECT-TYPE
DNS Domain name for the DHCP Scope.
1.3.6.1.4.1.14179.1.2.15.1.1.11DisplayString (SIZE(0..79))read-createcurrent
agentDhcpScopeDnsServerAddress1
OBJECT-TYPE
IP Address of the DHCP Scope's DNS Server 1.
1.3.6.1.4.1.14179.1.2.15.1.1.12IpAddressread-createcurrent
agentDhcpScopeDnsServerAddress2
OBJECT-TYPE
IP Address of the DHCP Scope's DNS Server 2.
1.3.6.1.4.1.14179.1.2.15.1.1.13IpAddressread-createcurrent
agentDhcpScopeDnsServerAddress3
OBJECT-TYPE
IP Address of the DHCP Scope's DNS Server 3.
1.3.6.1.4.1.14179.1.2.15.1.1.14IpAddressread-createcurrent
agentDhcpScopeNetbiosNameServerAddress1
OBJECT-TYPE
IP Address of DHCP Scope's Netbios Name Server 1.
1.3.6.1.4.1.14179.1.2.15.1.1.15IpAddressread-createcurrent
agentDhcpScopeNetbiosNameServerAddress2
OBJECT-TYPE
IP Address of DHCP Scope's Netbios Name Server 2.
1.3.6.1.4.1.14179.1.2.15.1.1.16IpAddressread-createcurrent
agentDhcpScopeNetbiosNameServerAddress3
OBJECT-TYPE
IP Address of DHCP Scope's Netbios Name Server 3.
1.3.6.1.4.1.14179.1.2.15.1.1.17IpAddressread-createcurrent
agentDhcpScopeState
OBJECT-TYPE
DHCP Scope's State.
1.3.6.1.4.1.14179.1.2.15.1.1.18INTEGER {disable(0), enable(1)}read-createcurrent
agentDhcpScopeRowStatus
OBJECT-TYPE
Dhcp Scope entry row status.
1.3.6.1.4.1.14179.1.2.15.1.1.30RowStatusread-createcurrent
agentSystemGroup
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.3
agentSaveConfig
OBJECT-TYPE
save config to NVRAM
1.3.6.1.4.1.14179.1.3.1INTEGER {enable(1), disable(2)}read-writecurrent
agentClearConfig
OBJECT-TYPE
clear config to factory defaults
1.3.6.1.4.1.14179.1.3.2INTEGER {enable(1), disable(2)}read-writecurrent
agentClearLags
OBJECT-TYPE
clear lag configuration
1.3.6.1.4.1.14179.1.3.3INTEGER {enable(1), disable(2)}read-writecurrent
agentClearLoginSessions
OBJECT-TYPE
close all telnet sessions
1.3.6.1.4.1.14179.1.3.4INTEGER {enable(1), disable(2)}read-writecurrent
agentClearPortStats
OBJECT-TYPE
clear all port statistics
1.3.6.1.4.1.14179.1.3.6INTEGER {enable(1), disable(2)}read-writecurrent
agentClearSwitchStats
OBJECT-TYPE
clear all switch statistics
1.3.6.1.4.1.14179.1.3.7INTEGER {enable(1), disable(2)}read-writecurrent
agentClearTrapLog
OBJECT-TYPE
clear trap log
1.3.6.1.4.1.14179.1.3.8INTEGER {enable(1), disable(2)}read-writecurrent
agentResetSystem
OBJECT-TYPE
reset the switch
1.3.6.1.4.1.14179.1.3.10INTEGER {enable(1), disable(2)}read-writecurrent
stats
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.4
portStatsTable
OBJECT-TYPE
A list of additional thernet statistics entries.
1.3.6.1.4.1.14179.1.4.1not-accessiblecurrent
portStatsEntry
OBJECT-TYPE
A collection of statistics kept for a particular Ethernet interface.
1.3.6.1.4.1.14179.1.4.1.1not-accessiblecurrent
portStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this portStatsEntry.
1.3.6.1.4.1.14179.1.4.1.1.1Integer32 (1..65535)read-onlycurrent
portStatsPktsTx64Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.2Counter32read-onlycurrent
portStatsPktsTx65to127Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.3Counter32read-onlycurrent
portStatsPktsTx128to255Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.4Counter32read-onlycurrent
portStatsPktsTx256to511Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.5Counter32read-onlycurrent
portStatsPktsTx512to1023Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.6Counter32read-onlycurrent
portStatsPktsTx1024to1518Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.7Counter32read-onlycurrent
portStatsPktsRx1519to1530Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.8Counter32read-onlycurrent
portStatsPktsTx1519to1530Octets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.9Counter32read-onlycurrent
portStatsPktsTxOversizeOctets
OBJECT-TYPE
The total number of packets (including bad packets) transmitted that were more than 1530 octets in length. (excluding framing bits but including FCS octets).
1.3.6.1.4.1.14179.1.4.1.1.30Counter32read-onlycurrent
switchingTraps
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.50
bsnSwitchingGroups
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.51
bsnSwitchingCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.14179.1.52

Notifications

NameOIDStatus
multipleUsersTrap
NOTIFICATION-TYPE
Multiple Users Log Trap.
1.3.6.1.4.1.14179.1.50.1current
broadcastStormStartTrap
NOTIFICATION-TYPE
Broadcast Storm Start Log Trap.
1.3.6.1.4.1.14179.1.50.2current
broadcastStormEndTrap
NOTIFICATION-TYPE
Broadcast Storm End Log Trap.
1.3.6.1.4.1.14179.1.50.3current
linkFailureTrap
NOTIFICATION-TYPE
trapMgrLinkFailureLogTrap.
1.3.6.1.4.1.14179.1.50.4current
vlanRequestFailureTrap
NOTIFICATION-TYPE
Vlan Request Failure Log Trap
1.3.6.1.4.1.14179.1.50.5current
vlanDeleteLastTrap
NOTIFICATION-TYPE
Last Vlan Delete Log Trap
1.3.6.1.4.1.14179.1.50.6current
vlanDefaultCfgFailureTrap
NOTIFICATION-TYPE
Default Vlan Config Failure Log Trap
1.3.6.1.4.1.14179.1.50.7current
vlanRestoreFailureTrap
NOTIFICATION-TYPE
Vlan Restore Failure Log Trap
1.3.6.1.4.1.14179.1.50.8current
fanFailureTrap
NOTIFICATION-TYPE
Fan Failure Log Trap.
1.3.6.1.4.1.14179.1.50.9current
stpInstanceNewRootTrap
NOTIFICATION-TYPE
STP Instance New Root Trap
1.3.6.1.4.1.14179.1.50.10current
stpInstanceTopologyChangeTrap
NOTIFICATION-TYPE
STP Instance Topology Change Trap
1.3.6.1.4.1.14179.1.50.11current
powerSupplyStatusChangeTrap
NOTIFICATION-TYPE
Power Supply Status Change Trap
1.3.6.1.4.1.14179.1.50.12current

Conformance

NameOIDStatus
bsnSwitchingAgentInfoGroup
OBJECT-GROUP
This collection of objects provide switching information.
1.3.6.1.4.1.14179.1.51.1current
bsnSwitchingAgentConfigGroup
OBJECT-GROUP
This collection of objects provide switching configuration information.
1.3.6.1.4.1.14179.1.51.2current
bsnSwitchingAgentSystemGroup
OBJECT-GROUP
This collection of objects provide switching system information and config.
1.3.6.1.4.1.14179.1.51.3current
bsnSwitchingAgentStatsGroup
OBJECT-GROUP
This collection of objects provide switching statistics.
1.3.6.1.4.1.14179.1.51.4current
bsnSwitchingObsGroup
OBJECT-GROUP
This collection of objects are obsoleted in bsnSwitching module.
1.3.6.1.4.1.14179.1.51.5obsolete
bsnSwitchingTrap
NOTIFICATION-GROUP
This collection of objects provides switching related notification.
1.3.6.1.4.1.14179.1.51.6current
bsnSwitchingCompliance
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the bsnSwitching module
1.3.6.1.4.1.14179.1.52.1current