AI-AP-MIB
- Registered at
- 1.3.6.1.4.1.14823.2.3.3.1
- Last updated
- 2020-08-14 17:45
- Organization
- Aruba, a Hewlett Packard Enterprise company
- Revisions
- 2020-08-14 17:45
- Namespace
- arubaos
- Source file
AI-AP-MIB- Digest
sha256:ffa0fe1fb092d67a634ee7abbde41b77f445ce03261b9e09b48565c2f8d11ace
Description
This MIB is for managing Aruba Instant WLAN
Contact
Postal: 3333 Scott Blvd, Santa Clara, CA 95054 E-mail: aruba-ext-eng-reg@hpe.com Phone: 408 227 4500 Fax: 408 752 0626
Imports
| From | Symbols |
|---|---|
| ARUBA-MIB | aiEnterpriseMibModules |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Counter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso, snmpModules |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, PhysAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TestAndIncr, TimeInterval, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
AI-AP-MIB ARUBA-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ArubaACLAction TEXTUAL-CONVENTION Represents the Actions in an ACL rule. | current | |||
| ArubaACLDomain TEXTUAL-CONVENTION Represents both the source and destination to which an ACL rule will be applied. | current | |||
| ArubaACLNetworkServiceType TEXTUAL-CONVENTION Represents the network service in an ACL Rule. | current | |||
| ArubaAPConductorStatus TEXTUAL-CONVENTION AP status as seen by the conductor controller (used to indicate a status change). | current | |||
| ArubaAPMasterStatus TEXTUAL-CONVENTION AP status as seen by the master controller (used to indicate a status change). **NOTE: this textual convention is deprecated and replaced by ArubaAPConductorStatus. | deprecated | |||
| ArubaAPMatchMethod TEXTUAL-CONVENTION Represents the match method of a suspected rogue AP. | current | |||
| ArubaAPMatchType TEXTUAL-CONVENTION Represents the match type of a suspected rogue AP. | current | |||
| ArubaAPStatus TEXTUAL-CONVENTION The status of the access point. | current | |||
| ArubaAPUplinkChangeReason TEXTUAL-CONVENTION Used to specify the reason for AP uplink change. linkFailure - The uplink went down vpnFailure - VPN tunnel could not be sustained using the uplink preemption - The uplink was pre-empted by a higher-priority uplink | current | |||
| ArubaAPUplinkType TEXTUAL-CONVENTION AP uplink type | current | |||
| ArubaARMChangeReason TEXTUAL-CONVENTION The reason for ARM based change. | current | |||
| ArubaAccessPointMode TEXTUAL-CONVENTION The mode of the access point. | current | |||
| ArubaActiveState TEXTUAL-CONVENTION Represents if a feature is active or inactive. | current | |||
| ArubaAddressType TEXTUAL-CONVENTION Address Type. | current | |||
| ArubaAntennaSetting TEXTUAL-CONVENTION Represents the status of the external antenna. | current | |||
| ArubaAuthServerType TEXTUAL-CONVENTION The type of the auth server. | current | |||
| ArubaAuthenticationMethods TEXTUAL-CONVENTION Authentication Method. | current | |||
| ArubaBlackListReason TEXTUAL-CONVENTION Black List Reason **NOTE: this textual convention is deprecated and replaced by ArubaDenyListReason. | deprecated | |||
| ArubaCallStates TEXTUAL-CONVENTION The Call state. | current | |||
| ArubaCardType TEXTUAL-CONVENTION Type of the hardware module. | current | |||
| ArubaConfigurationChangeType TEXTUAL-CONVENTION Configuration Change Types. | current | |||
| ArubaConfigurationState TEXTUAL-CONVENTION Configuration Transfer Types. | current | |||
| ArubaDBType TEXTUAL-CONVENTION DataBase Type. | current | |||
| ArubaDaysOfWeek TEXTUAL-CONVENTION Represents the Actions in an ACL rule. | current | |||
| ArubaDenyListReason TEXTUAL-CONVENTION Deny List Reason. | current | |||
| ArubaDot1dState TEXTUAL-CONVENTION Represents the controller port spanning tree state. | current | |||
| ArubaESIServerMode TEXTUAL-CONVENTION The mode of the ESI server. | current | |||
| ArubaESIServerStatus TEXTUAL-CONVENTION The status of the ESI server. | current | |||
| ArubaEnableValue TEXTUAL-CONVENTION Represents a Flag which is either Enabled or Disabled. | current | |||
| ArubaEncryptionMethods TEXTUAL-CONVENTION Represents the Actions in an ACL rule. | current | |||
| ArubaEncryptionType TEXTUAL-CONVENTION Encryption Method. | current | |||
| ArubaEnet1Mode TEXTUAL-CONVENTION Represents the Mode of the Ethernet port on the Access Point | current | |||
| ArubaFrameType TEXTUAL-CONVENTION Represents the Frame type. | current | |||
| ArubaHTExtChannel TEXTUAL-CONVENTION Represents the extension channel offset relative to the current channel. | current | |||
| ArubaHTMode TEXTUAL-CONVENTION Represents the HT status of the access point or client. | current | |||
| ArubaHTRate TEXTUAL-CONVENTION Represents HT rate | current | |||
| ArubaHashAlgorithms TEXTUAL-CONVENTION Represents the Actions in an ACL rule. | current | |||
| ArubaIfType TEXTUAL-CONVENTION The type of interface referred to by the value of ifIndex. | current | |||
| ArubaMeshRole TEXTUAL-CONVENTION Mesh role | current | |||
| ArubaMonAuthAlgorithm TEXTUAL-CONVENTION Represents the WPA authentication algorithm supported by the access point. | current | |||
| ArubaMonEncryptionCipher TEXTUAL-CONVENTION Represents the WPA encryption cipher supported by the access point. | current | |||
| ArubaMonEncryptionType TEXTUAL-CONVENTION Represents the encryption type supported by the access point. | current | |||
| ArubaMonitorMode TEXTUAL-CONVENTION Represents whether the AP has any radios dedicated to monitoring. | current | |||
| ArubaOperStateValue TEXTUAL-CONVENTION Represents Operational state of an interface. | current | |||
| ArubaPhyType TEXTUAL-CONVENTION Represents the PHY-type of the access point or client. Wired clients will show 'wired' in user MIB entries. | current | |||
| ArubaPoeState TEXTUAL-CONVENTION Represents the POE mode. | current | |||
| ArubaPortDuplex TEXTUAL-CONVENTION Port Duplexity. | current | |||
| ArubaPortMode TEXTUAL-CONVENTION Represents the controller port mode. | current | |||
| ArubaPortSpeed TEXTUAL-CONVENTION Port Speed. | current | |||
| ArubaPortType TEXTUAL-CONVENTION Port Type. | current | |||
| ArubaPortalServerDownReason TEXTUAL-CONVENTION Used to specify the reason for Portal server down. connectFail - Connect Portal server fail | current | |||
| ArubaRogueApType TEXTUAL-CONVENTION Represents the Rogue AP Type. | current | |||
| ArubaStationType TEXTUAL-CONVENTION Represents the station type. | current | |||
| ArubaSubAuthenticationMethods TEXTUAL-CONVENTION Sub Authentication Method (e.g. EAP type). | current | |||
| ArubaSupportStatus TEXTUAL-CONVENTION Represents if a feature is supported or unsupported. | current | |||
| ArubaSwitchRole TEXTUAL-CONVENTION Represents the role of the controller | current | |||
| ArubaUSBStatus TEXTUAL-CONVENTION USB device status | current | |||
| ArubaUnprovisionedStatus TEXTUAL-CONVENTION Represents whether the AP is provisioned or not. | current | |||
| ArubaUserForwardMode TEXTUAL-CONVENTION User Forwarding Mode. | current | |||
| ArubaVlanValidRange TEXTUAL-CONVENTION Represents the Valid Vlan Id Range. | current | |||
| ArubaVoiceCacBit TEXTUAL-CONVENTION Voice CAC bit flags | current | |||
| ArubaVoiceCdrDirection TEXTUAL-CONVENTION VoIP CDR direction | current | |||
| ArubaVoipProtocol TEXTUAL-CONVENTION VoIP protocol used | current | |||
| ArubaVoipProtocolType TEXTUAL-CONVENTION The type of VoIP protocols supported. | current | |||
| ArubaVoipRegState TEXTUAL-CONVENTION VoIP registered state | current | |||
| ArubaVrrpState TEXTUAL-CONVENTION DataBase Type. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| aiInfoGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.1 | |||
| aiVirtualControllerKey OBJECT-TYPE Unique Virtual Controller key | 1.3.6.1.4.1.14823.2.3.3.1.1.1 | DisplayString | read-only | current |
| aiVirtualControllerName OBJECT-TYPE Virtual Controller name | 1.3.6.1.4.1.14823.2.3.3.1.1.2 | DisplayString | read-only | current |
| aiVirtualControllerOrganization OBJECT-TYPE Virtual Controller organization | 1.3.6.1.4.1.14823.2.3.3.1.1.3 | DisplayString | read-only | current |
| aiVirtualControllerVersion OBJECT-TYPE Software Version | 1.3.6.1.4.1.14823.2.3.3.1.1.4 | DisplayString | read-only | current |
| aiVirtualControllerIPAddress OBJECT-TYPE Virtual Controller IP Address. If this is not set, returns 0.0.0.0 | 1.3.6.1.4.1.14823.2.3.3.1.1.5 | IpAddress | read-only | current |
| aiMasterIPAddress OBJECT-TYPE IP Address of AP where virtual controller software is active **NOTE: this object is deprecated and replaced by aiConductorIPAddress | 1.3.6.1.4.1.14823.2.3.3.1.1.6 | IpAddress | read-only | deprecated |
| aiWlanSSIDTable OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.1.7 | not-accessible | current | |
| aiWlanSSIDEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1 | not-accessible | current | |
| aiSSIDIndex OBJECT-TYPE SSID Index | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1.1 | Integer32 | read-only | current |
| aiSSID OBJECT-TYPE SSID | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1.2 | OCTET STRING (SIZE(0..64)) | read-only | current |
| aiSSIDStatus OBJECT-TYPE Indicates the whether the SSID is enabled(0) or disabled(1) | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1.3 | INTEGER {enable(0), disable(1)} | read-only | current |
| aiSSIDClientNum OBJECT-TYPE Client Number of per SSID | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1.4 | Integer32 | read-only | current |
| aiSSIDHide OBJECT-TYPE Indicates the whether the SSID is hide enabled(1) or disabled(0) | 1.3.6.1.4.1.14823.2.3.3.1.1.7.1.5 | INTEGER {disable(0), enable(1)} | read-only | current |
| aiInterferAccessPointTable OBJECT-TYPE This contains all interfer access points infomation | 1.3.6.1.4.1.14823.2.3.3.1.1.8 | not-accessible | current | |
| aiInterferAccessPointEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1 | not-accessible | current | |
| aiInterferAPIndex OBJECT-TYPE Interfer Access Point Index | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.1 | Integer32 | read-only | current |
| aiInterferAPBSSID OBJECT-TYPE Interfer Access Point MAC | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.2 | MacAddress | read-only | current |
| aiInterferAPESSID OBJECT-TYPE Interfer Access Point ESSID | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.3 | OCTET STRING (SIZE(0..64)) | read-only | current |
| aiInterferAPChannel OBJECT-TYPE Interfer Access Point Channel | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.4 | DisplayString | read-only | current |
| aiInterferAPPhyType OBJECT-TYPE Interfer Access Point Phy Type | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.5 | DisplayString | read-only | current |
| aiInterferAPEncr OBJECT-TYPE Interfer Access Point Encryption | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.6 | DisplayString | read-only | current |
| aiInterferAPAvgSnr OBJECT-TYPE Interfer Access Point Average Snr | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.7 | Integer32 | read-only | current |
| aiInterferAPType OBJECT-TYPE Interfer Access Point AP Type | 1.3.6.1.4.1.14823.2.3.3.1.1.8.1.8 | DisplayString | read-only | current |
| aiMeshTable OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.1.15 | not-accessible | current | |
| aiMeshEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1 | not-accessible | current | |
| aiMeshIndex OBJECT-TYPE Mesh Index | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.1 | Integer32 | read-only | current |
| aiMeshPointMac OBJECT-TYPE Mesh Point Mac Address | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.2 | MacAddress | read-only | current |
| aiMeshPortalMac OBJECT-TYPE Mesh Portal Mac Address | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.3 | DisplayString | read-only | current |
| aiMeshChannel OBJECT-TYPE Mesh Channel | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.4 | DisplayString | read-only | current |
| aiMeshAvgRssi OBJECT-TYPE Mesh Average RSSI | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.5 | Integer32 | read-only | current |
| aiMeshHops OBJECT-TYPE Mesh Hops | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.6 | Integer32 | read-only | current |
| aiMeshAge OBJECT-TYPE Mesh Age | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.7 | Integer32 | read-only | current |
| aiMeshCost OBJECT-TYPE Mesh Cost | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.8 | DisplayString | read-only | current |
| aiMeshRelation OBJECT-TYPE Mesh Relation | 1.3.6.1.4.1.14823.2.3.3.1.1.15.1.9 | DisplayString | read-only | current |
| aiConductorIPAddress OBJECT-TYPE IP Address of AP where virtual controller software is active | 1.3.6.1.4.1.14823.2.3.3.1.1.16 | IpAddress | read-only | current |
| aiStateGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.2 | |||
| aiAccessPointTable OBJECT-TYPE This contains all access points connected to the virtual controller. This table is empty on AP where virtual controller is not active | 1.3.6.1.4.1.14823.2.3.3.1.2.1 | not-accessible | current | |
| aiAccessPointEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1 | not-accessible | current | |
| aiAPMACAddress OBJECT-TYPE Access Point MAC Address | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.1 | MacAddress | read-only | current |
| aiAPName OBJECT-TYPE Access Point name | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.2 | DisplayString (SIZE(0..255)) | read-only | current |
| aiAPIPAddress OBJECT-TYPE Access Point IP Address | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.3 | IpAddress | read-only | current |
| aiAPSerialNum OBJECT-TYPE Access Point Serial Number | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.4 | DisplayString (SIZE(0..64)) | read-only | current |
| aiAPModel OBJECT-TYPE Access Point System OID | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.5 | OBJECT IDENTIFIER | read-only | current |
| aiAPModelName OBJECT-TYPE Access Point Model Name | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.6 | DisplayString (SIZE(0..32)) | read-only | current |
| aiAPCPUUtilization OBJECT-TYPE Access Point CPU Utilization | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.7 | Integer32 | read-only | current |
| aiAPMemoryFree OBJECT-TYPE Amount of memory free in the access point in bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.8 | Integer32 | read-only | current |
| aiAPUptime OBJECT-TYPE Access Point uptime | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.9 | TimeTicks | read-only | current |
| aiAPTotalMemory OBJECT-TYPE Total amount of memory available in the AP in bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.10 | Integer32 | read-only | current |
| aiAPStatus OBJECT-TYPE Indicates the Access Point Status | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.11 | INTEGER {up(1), down(2)} | read-only | current |
| aiAPHwopmode OBJECT-TYPE AP HW OPMODE | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.12 | INTEGER {default(0), rsdbsplit(1), rsdb5g(2), rsdb2g(3), dual5gon(4), dual5goff(5), split5goff(6), split5gon(7)} | read-only | current |
| aiAPRole OBJECT-TYPE AP State | 1.3.6.1.4.1.14823.2.3.3.1.2.1.1.13 | DisplayString | read-only | current |
| aiRadioTable OBJECT-TYPE This table contains all radios of all access points connected to the virtual controller. This table is indexed by Access Point MAC Address and radio number | 1.3.6.1.4.1.14823.2.3.3.1.2.2 | not-accessible | current | |
| aiRadioEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1 | not-accessible | current | |
| aiRadioAPMACAddress OBJECT-TYPE MAC Address of access point where this radio is active | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.1 | MacAddress | read-only | current |
| aiRadioIndex OBJECT-TYPE Radio number | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.2 | Integer32 | read-only | current |
| aiRadioMACAddress OBJECT-TYPE Radio MAC Address | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.3 | MacAddress | read-only | current |
| aiRadioChannel OBJECT-TYPE Radio channel. First byte contains primary channel and first two bits on second byte contains indicator for secondary channel. If first two bits of second byte is 0, it is a 20MHz channel. If first two bits of second byte is 01, secondary channel is above primary channel, if first two bits of second by is 10, secondary channel is below the primary channel. | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.4 | DisplayString | read-only | current |
| aiRadioTransmitPower OBJECT-TYPE Radio transmit power | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.5 | Integer32 | read-only | current |
| aiRadioNoiseFloor OBJECT-TYPE Radio noise floor in dBm | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.6 | Integer32 | read-only | current |
| aiRadioUtilization4 OBJECT-TYPE Radio channel utilization 4 second average | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.7 | Integer32 | read-only | current |
| aiRadioUtilization64 OBJECT-TYPE Radio channel utilization 64 second average | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.8 | Integer32 | read-only | current |
| aiRadioTxTotalFrames OBJECT-TYPE Total transmitted frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.9 | Counter32 | read-only | current |
| aiRadioTxMgmtFrames OBJECT-TYPE Transmitted management frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.10 | Counter32 | read-only | current |
| aiRadioTxDataFrames OBJECT-TYPE Transmitted data frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.11 | Counter32 | read-only | current |
| aiRadioTxDataBytes OBJECT-TYPE Transmitted data bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.12 | Counter32 | read-only | current |
| aiRadioTxDrops OBJECT-TYPE Total frames dropped during transmission | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.13 | Counter32 | read-only | current |
| aiRadioRxTotalFrames OBJECT-TYPE Total received frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.14 | Counter32 | read-only | current |
| aiRadioRxDataFrames OBJECT-TYPE Received data frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.15 | Counter32 | read-only | current |
| aiRadioRxDataBytes OBJECT-TYPE Received data bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.16 | Counter32 | read-only | current |
| aiRadioRxMgmtFrames OBJECT-TYPE Received management frames | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.17 | Counter32 | read-only | current |
| aiRadioRxBad OBJECT-TYPE Frames received in error | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.18 | Counter32 | read-only | current |
| aiRadioPhyEvents OBJECT-TYPE Number of phy events that indicates frames not received because of interference | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.19 | Counter32 | read-only | current |
| aiRadioStatus OBJECT-TYPE Radio state of AP - UP/DOWN | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.20 | INTEGER {up(1), down(2)} | read-only | current |
| aiRadioClientNum OBJECT-TYPE Client Number of per Radio | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.21 | Integer32 | read-only | current |
| aiRadioMode OBJECT-TYPE Radio state of AP - access/monitor | 1.3.6.1.4.1.14823.2.3.3.1.2.2.1.22 | DisplayString | read-only | current |
| aiWlanTable OBJECT-TYPE This table contains all BSSIDs active on this virtual controller. This table is indexed by Access Point MAC Address and a WLAN Index | 1.3.6.1.4.1.14823.2.3.3.1.2.3 | not-accessible | current | |
| aiWlanEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1 | not-accessible | current | |
| aiWlanAPMACAddress OBJECT-TYPE MAC Address of access point where WLAN is active | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.1 | MacAddress | read-only | current |
| aiWlanIndex OBJECT-TYPE Index of WLAN. This is a unique index assigned to the WLAN active on the access point. | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.2 | Integer32 | read-only | current |
| aiWlanESSID OBJECT-TYPE ESSID of WLAN | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.3 | DisplayString | read-only | current |
| aiWlanMACAddress OBJECT-TYPE BSSID of WLAN | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.4 | MacAddress | read-only | current |
| aiWlanTxTotalFrames OBJECT-TYPE Total transmitted frames | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.5 | Counter32 | read-only | current |
| aiWlanTxDataFrames OBJECT-TYPE Transmitted data frames | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.6 | Counter32 | read-only | current |
| aiWlanTxDataBytes OBJECT-TYPE Transmitted data bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.7 | Counter32 | read-only | current |
| aiWlanRxTotalFrames OBJECT-TYPE Total received frames | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.8 | Counter32 | read-only | current |
| aiWlanRxDataFrames OBJECT-TYPE Received data frames | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.9 | Counter32 | read-only | current |
| aiWlanRxDataBytes OBJECT-TYPE Received data bytes | 1.3.6.1.4.1.14823.2.3.3.1.2.3.1.10 | Counter32 | read-only | current |
| aiClientTable OBJECT-TYPE This table contains information about all clients connected to the virtual controller. When a client roams from one access point to another, all counters in this table are reset to 0. aiClientUptime also get reset on a mobility event | 1.3.6.1.4.1.14823.2.3.3.1.2.4 | not-accessible | current | |
| aiClientEntry OBJECT-TYPE | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1 | not-accessible | current | |
| aiClientMACAddress OBJECT-TYPE MAC Address of client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.1 | MacAddress | read-only | current |
| aiClientWlanMACAddress OBJECT-TYPE BSSID of WLAN where client is associated | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.2 | MacAddress | read-only | current |
| aiClientIPAddress OBJECT-TYPE Client IP Address | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.3 | IpAddress | read-only | current |
| aiClientAPIPAddress OBJECT-TYPE Associated Access Point IP Address | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.4 | IpAddress | read-only | current |
| aiClientName OBJECT-TYPE Name of user using the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.5 | DisplayString | read-only | current |
| aiClientOperatingSystem OBJECT-TYPE Client operating system | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.6 | DisplayString | read-only | current |
| aiClientSNR OBJECT-TYPE Signal to noise ratio of client connection to the access point | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.7 | Integer32 | read-only | current |
| aiClientTxDataFrames OBJECT-TYPE Total frames transmitted by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.8 | Counter32 | read-only | current |
| aiClientTxDataBytes OBJECT-TYPE Total bytes transmitted by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.9 | Counter32 | read-only | current |
| aiClientTxRetries OBJECT-TYPE Total number of retry frames transmitted by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.10 | Counter32 | read-only | current |
| aiClientTxRate OBJECT-TYPE Transmit rate of client in mbps | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.11 | Integer32 | read-only | current |
| aiClientRxDataFrames OBJECT-TYPE Total frames received by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.12 | Counter32 | read-only | current |
| aiClientRxDataBytes OBJECT-TYPE Total bytes received by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.13 | Counter32 | read-only | current |
| aiClientRxRetries OBJECT-TYPE Total number of retry frames received by the client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.14 | Counter32 | read-only | current |
| aiClientRxRate OBJECT-TYPE Receive rate of client in mbps | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.15 | Integer32 | read-only | current |
| aiClientUptime OBJECT-TYPE Client uptime. On mobility event all counters are reset to 0 and uptime gets reset to 0. | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.16 | TimeTicks | read-only | current |
| aiClientPhyType OBJECT-TYPE The wireless PHY type to which the client is associated, or 'wired' | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.17 | ArubaPhyType | read-only | current |
| aiClientHtMode OBJECT-TYPE The HT mode of this Client | 1.3.6.1.4.1.14823.2.3.3.1.2.4.1.18 | ArubaHTMode | read-only | current |
| aiVoiceClientTable OBJECT-TYPE Table of voice clients | 1.3.6.1.4.1.14823.2.3.3.1.2.5 | not-accessible | current | |
| aiVoiceClientEntry OBJECT-TYPE Entry of a voice client | 1.3.6.1.4.1.14823.2.3.3.1.2.5.1 | not-accessible | current | |
| aiClientMac OBJECT-TYPE MAC address of voice client | 1.3.6.1.4.1.14823.2.3.3.1.2.5.1.1 | MacAddress | read-only | current |
| aiClientIP OBJECT-TYPE IP address of voice client | 1.3.6.1.4.1.14823.2.3.3.1.2.5.1.2 | IpAddress | read-only | current |
| aiClientAPMac OBJECT-TYPE MAC address of AP on which voice client is associated currently | 1.3.6.1.4.1.14823.2.3.3.1.2.5.1.3 | MacAddress | read-only | current |
| aiClientAPName OBJECT-TYPE Name of AP on which voice client is associated currently | 1.3.6.1.4.1.14823.2.3.3.1.2.5.1.4 | DisplayString | read-only | current |
| aiManagedInfoGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.3 | |||
| aiManagedModeSinceLastSync OBJECT-TYPE Time since last config was applied | 1.3.6.1.4.1.14823.2.3.3.1.3.1 | DisplayString | read-only | current |
| aiTrapsGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.200 | |||
| aiTrapObjectsGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.200.1 | |||
| wlsxTrapAPMacAddress OBJECT-TYPE This object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.1 | MacAddress | accessible-for-notify | current |
| wlsxTrapAPIpAddress OBJECT-TYPE This object is used in the traps to indicate the IP address of an access point, for which the trap is being raised. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.2 | IpAddress | accessible-for-notify | current |
| wlsxTrapAPBSSID OBJECT-TYPE This object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.3 | MacAddress | accessible-for-notify | current |
| wlsxTrapEssid OBJECT-TYPE This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.4 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTargetAPBSSID OBJECT-TYPE This object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.5 | MacAddress | accessible-for-notify | current |
| wlsxTrapTargetAPSSID OBJECT-TYPE This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.6 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTargetAPChannel OBJECT-TYPE This object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an wlsxr monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.7 | Integer32 | accessible-for-notify | current |
| wlsxTrapNodeMac OBJECT-TYPE This object is used in the traps to indicate the MAC address of a node. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.8 | MacAddress | accessible-for-notify | current |
| wlsxTrapSourceMac OBJECT-TYPE This object is used in the traps to indicate the MAC address of the source. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.9 | MacAddress | accessible-for-notify | current |
| wlsxReceiverMac OBJECT-TYPE This object is used in the traps to indicate the MAC address of the receiver. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.10 | MacAddress | accessible-for-notify | current |
| wlsxTrapTransmitterMac OBJECT-TYPE This object is used in the traps to indicate the MAC address of the transmitter. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.11 | MacAddress | accessible-for-notify | current |
| wlsxTrapReceiverMac OBJECT-TYPE This object is used in the traps to indicate the MAC address of the receiver. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.12 | MacAddress | accessible-for-notify | current |
| wlsxTrapSnr OBJECT-TYPE This object is used in the traps to indicate the Signal to Noise ratio. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.13 | Integer32 | accessible-for-notify | current |
| wlsxTrapSignatureName OBJECT-TYPE This object is used in the traps to indicate the Signature Name. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.14 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapFrameType OBJECT-TYPE This object is used in the traps to indicate the Frame Type | 1.3.6.1.4.1.14823.2.3.3.1.200.1.15 | ArubaFrameType | accessible-for-notify | current |
| wlsxTrapAddressType OBJECT-TYPE This object is used in the traps to indicate the Address type. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.16 | ArubaAddressType | accessible-for-notify | current |
| wlsxTrapAPLocation OBJECT-TYPE This object is used in the traps to indicate the Location of the AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.17 | DisplayString (SIZE(0..255)) | accessible-for-notify | current |
| wlsxTrapAPChannel OBJECT-TYPE This object is used in the traps to indicate the Current Channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.18 | Integer32 | accessible-for-notify | current |
| wlsxTrapAPTxPower OBJECT-TYPE This object is used in the traps to indicate the AP Transmit Power. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.19 | Integer32 | accessible-for-notify | current |
| wlsxTrapMatchedMac OBJECT-TYPE This object is used in the traps to indicate the MAC address | 1.3.6.1.4.1.14823.2.3.3.1.200.1.20 | MacAddress | accessible-for-notify | current |
| wlsxTrapMatchedIp OBJECT-TYPE This object is used in the traps to indicate the IP address | 1.3.6.1.4.1.14823.2.3.3.1.200.1.21 | IpAddress | accessible-for-notify | current |
| wlsxTrapRogueIfoURL OBJECT-TYPE This object is used to point to the WEBUI Rogue AP information URL. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.22 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapVlanId OBJECT-TYPE This object is used in the traps to indicate the VLAN Id. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.23 | Integer32 | accessible-for-notify | current |
| wlsxTrapAdminStatus OBJECT-TYPE This object is used in the traps to indicate the admin status of VLAN. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.24 | ArubaEnableValue | accessible-for-notify | current |
| wlsxTrapOperStatus OBJECT-TYPE This object is used in the traps to indicate the admin status of VLAN. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.25 | ArubaOperStateValue | accessible-for-notify | current |
| wlsxTrapAuthServerName OBJECT-TYPE This object is used in the traps to indicate the Authentication Server used for Authentication. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.26 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapAuthServerTimeout OBJECT-TYPE This object is used in the traps to indicate the Authentication Server Timeout. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.27 | Integer32 | accessible-for-notify | current |
| wlsxTrapCardSlot OBJECT-TYPE This object is used in the traps to indicate the Slot in which this card is present. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.28 | Integer32 | accessible-for-notify | current |
| wlsxTrapTemperatureValue OBJECT-TYPE This object is used in the traps to indicate the Temperature Value. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.29 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapProcessName OBJECT-TYPE This object is used in the traps to indicate the Process name. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.30 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapFanNumber OBJECT-TYPE This object is used in the traps to indicate the Fan Number. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.31 | Integer32 | accessible-for-notify | current |
| wlsxTrapVoltageType OBJECT-TYPE This object is used in the traps to indicate the type of Voltage. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.32 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapVoltageValue OBJECT-TYPE This object is used in the traps to indicate the voltage value in Float. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.33 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapStationBlackListReason OBJECT-TYPE The Reason for which a station is black listed. **NOTE: this object is deprecated and replaced by wlsxTrapStationDenyListReason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.34 | ArubaBlackListReason | accessible-for-notify | deprecated |
| wlsxTrapSpoofedIpAddress OBJECT-TYPE This object is used in a trap to identify a spoofed IP address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.35 | IpAddress | accessible-for-notify | current |
| wlsxTrapSpoofedOldPhyAddress OBJECT-TYPE This object is used in a trap to identify an old MAC address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.36 | MacAddress | accessible-for-notify | current |
| wlsxTrapSpoofedNewPhyAddress OBJECT-TYPE This object is used in a trap to identify a New MAC address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.37 | MacAddress | accessible-for-notify | current |
| wlsxTrapDBName OBJECT-TYPE This object is used in a trap to identify name of the database. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.38 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapDBUserName OBJECT-TYPE This object is used in a trap to identify name of the database user. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.39 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapDBIpAddress OBJECT-TYPE This object is used in a trap to identify the IpAddress of the Database. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.40 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapDBType OBJECT-TYPE This object is used in a trap to identify the port of the user. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.41 | ArubaDBType | accessible-for-notify | current |
| wlsxTrapVrrpID OBJECT-TYPE This object contains the Virtual Router Identifier. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.42 | Integer32 | accessible-for-notify | current |
| wlsxTrapVrrpMasterIp OBJECT-TYPE This object contains the Master IP address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.43 | IpAddress | accessible-for-notify | current |
| wlsxTrapVrrpOperState OBJECT-TYPE This object represents the VRRP Operational state. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.44 | ArubaVrrpState | accessible-for-notify | current |
| wlsxTrapESIServerGrpName OBJECT-TYPE This object represents the External Services Interface (ESI) Server Group name | 1.3.6.1.4.1.14823.2.3.3.1.200.1.45 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapESIServerName OBJECT-TYPE This object represents the External Services Interface (ESI) Server Name | 1.3.6.1.4.1.14823.2.3.3.1.200.1.46 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapESIServerIpAddress OBJECT-TYPE This object represents the External Services Interface (ESI) Server IP address | 1.3.6.1.4.1.14823.2.3.3.1.200.1.47 | IpAddress | accessible-for-notify | current |
| wlsxTrapLicenseDaysRemaining OBJECT-TYPE This object represents number of the days remaining prior to a license expiry. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.48 | Integer32 | accessible-for-notify | current |
| wlsxTrapSwitchIp OBJECT-TYPE This object represents the controller IP address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.49 | IpAddress | accessible-for-notify | current |
| wlsxTrapSwitchRole OBJECT-TYPE This object represents the Role of the controller. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.50 | ArubaSwitchRole | accessible-for-notify | current |
| wlsxTrapUserIpAddress OBJECT-TYPE This object represents IP address of the User. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.51 | IpAddress | accessible-for-notify | current |
| wlsxTrapUserPhyAddress OBJECT-TYPE This object represents MAC address of the User. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.52 | MacAddress | accessible-for-notify | current |
| wlsxTrapUserName OBJECT-TYPE This object represents the user name. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.53 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapUserRole OBJECT-TYPE This object represents the Authentication method of the user. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.54 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapUserAuthenticationMethod OBJECT-TYPE This object represents the Authentication method of the user. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.55 | ArubaAuthenticationMethods | accessible-for-notify | current |
| wlsxTrapAPRadioNumber OBJECT-TYPE This object represents the radio number. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.56 | Integer32 | accessible-for-notify | current |
| wlsxTrapRogueInfoURL OBJECT-TYPE This object is used to point to the WEBGUI Rogue AP information URL. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.57 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapInterferingAPInfoURL OBJECT-TYPE This object is used to point to the WEBGUI Rogue interfering AP information URL. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.58 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapPortNumber OBJECT-TYPE This object is used in the traps to indicate the port number. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.59 | Integer32 | accessible-for-notify | current |
| wlsxTrapTime OBJECT-TYPE This object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.60 | DateAndTime | accessible-for-notify | current |
| wlsxTrapHostIp OBJECT-TYPE This object represents the Trap host. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.61 | IpAddress | accessible-for-notify | current |
| wlsxTrapHostPort OBJECT-TYPE This object represents the Trap host port. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.62 | Integer32 | accessible-for-notify | current |
| wlsxTrapConfigurationId OBJECT-TYPE This object represents the ID of the configuration, to be used in traps. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.63 | Integer32 | accessible-for-notify | current |
| wlsxTrapCTSURL OBJECT-TYPE This object represents the URL from which the transfer should happen. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.64 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapCTSTransferType OBJECT-TYPE This object represents the transfer type, upload or download. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.65 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapConfigurationState OBJECT-TYPE This object represents state of the configuration transfer. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.66 | ArubaConfigurationState | accessible-for-notify | current |
| wlsxTrapUpdateFailureReason OBJECT-TYPE This object represents the reason for the update failure. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.67 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapUpdateFailedObj OBJECT-TYPE This variable represents the AMAPI object which is the reason for the the update failure. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.68 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTableEntryChangeType OBJECT-TYPE This object represents type of the configuration change. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.69 | ArubaConfigurationChangeType | accessible-for-notify | current |
| wlsxTrapGlobalConfigObj OBJECT-TYPE This variable represents the AMAPI object corresponding to the global configuration change. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.70 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTableGenNumber OBJECT-TYPE This object represents generation number of a table. Used in the MMS, to keep track of the table content changes. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.71 | Integer32 | accessible-for-notify | current |
| wlsxTrapLicenseId OBJECT-TYPE This object is used in the traps to indicate the license ID. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.72 | Integer32 | accessible-for-notify | current |
| wlsxTrapConfidenceLevel OBJECT-TYPE This object is used in the traps to indicate the Confidence Level as a percentage | 1.3.6.1.4.1.14823.2.3.3.1.200.1.73 | Integer32 | accessible-for-notify | current |
| wlsxTrapMissingLicenses OBJECT-TYPE This variable indicates any licenses that are not present during a configuration update | 1.3.6.1.4.1.14823.2.3.3.1.200.1.74 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxVoiceCurrentNumCdr OBJECT-TYPE This object represents the number of CDRs in buffer. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.75 | Integer32 | accessible-for-notify | current |
| wlsxTrapTunnelId OBJECT-TYPE This Object represents the tunnel ID. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.76 | Integer32 | accessible-for-notify | current |
| wlsxTrapTunnelStatus OBJECT-TYPE This Object represents the tunnel Status. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.77 | Integer32 | accessible-for-notify | current |
| wlsxTrapTunnelUpReason OBJECT-TYPE This Object represents the tunnel up reason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.78 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTunnelDownReason OBJECT-TYPE This Object represents the tunnel down reason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.79 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapApSerialNumber OBJECT-TYPE This object represents the AP Serial Number. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.80 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapTimeStr OBJECT-TYPE This object represents the Time in String format. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.81 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapMasterIp OBJECT-TYPE This object represents the master IP address. **NOTE: this object is deprecated and replaced by wlsxTrapConductorIp | 1.3.6.1.4.1.14823.2.3.3.1.200.1.82 | IpAddress | accessible-for-notify | deprecated |
| wlsxTrapLocalIp OBJECT-TYPE This object represents the Local IP address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.83 | IpAddress | accessible-for-notify | current |
| wlsxTrapMasterName OBJECT-TYPE This object represents the master controller name. **NOTE: this object is deprecated and replaced by wlsxTrapConductorName | 1.3.6.1.4.1.14823.2.3.3.1.200.1.84 | DisplayString (SIZE(0..64)) | accessible-for-notify | deprecated |
| wlsxTrapLocalName OBJECT-TYPE This object represents the local controller name. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.85 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapPrimaryControllerIp OBJECT-TYPE This object represents the IP address of the AP's primary controller. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.86 | IpAddress | accessible-for-notify | current |
| wlsxTrapBackupControllerIp OBJECT-TYPE This object represents the IP address of the AP's backup controller. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.87 | IpAddress | accessible-for-notify | current |
| wlsxTrapSpoofedFrameType OBJECT-TYPE This object is used in the traps to indicate the Spoofed Frame Type | 1.3.6.1.4.1.14823.2.3.3.1.200.1.88 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapAssociationType OBJECT-TYPE This object is used in the traps to indicate the type of association | 1.3.6.1.4.1.14823.2.3.3.1.200.1.89 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapDeviceIpAddress OBJECT-TYPE This object represents the IP address of a device seen by an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.90 | IpAddress | accessible-for-notify | current |
| wlsxTrapDeviceMac OBJECT-TYPE This object represents the MAC address of a device seen by an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.91 | MacAddress | accessible-for-notify | current |
| wlsxTrapVcIpAddress OBJECT-TYPE This object represents the Ip Address of a Voice client. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.92 | IpAddress | accessible-for-notify | current |
| wlsxTrapVcMacAddress OBJECT-TYPE This object represents the MAC address of a Voice client. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.93 | MacAddress | accessible-for-notify | current |
| wlsxTrapAPName OBJECT-TYPE This object is used in the traps to indicate the Name of the AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.94 | DisplayString (SIZE(0..255)) | accessible-for-notify | current |
| wlsxTrapApMode OBJECT-TYPE This Object represents the AP Mode. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.95 | Integer32 | accessible-for-notify | current |
| wlsxTrapAPPrevChannel OBJECT-TYPE This object is used in the traps to indicate the Previous Channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.96 | Integer32 | accessible-for-notify | current |
| wlsxTrapAPPrevChannelSec OBJECT-TYPE This object is used in the traps to indicate the Previous Secondary Channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.97 | ArubaHTExtChannel | accessible-for-notify | current |
| wlsxTrapAPPrevTxPower OBJECT-TYPE This object is used in the traps to indicate previous AP Transmit Power. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.98 | Integer32 | accessible-for-notify | current |
| wlsxTrapAPCurMode OBJECT-TYPE This Object represents the APs Current Mode. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.99 | ArubaAccessPointMode | accessible-for-notify | current |
| wlsxTrapAPPrevMode OBJECT-TYPE This Object represents the APs Previous Mode. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.100 | ArubaAccessPointMode | accessible-for-notify | current |
| wlsxTrapAPARMChangeReason OBJECT-TYPE This Object represents the APs Previous Mode. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.101 | ArubaARMChangeReason | accessible-for-notify | current |
| wlsxTrapAPChannelSec OBJECT-TYPE This object is used in the traps to indicate the Current Secondary Channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.102 | ArubaHTExtChannel | accessible-for-notify | current |
| wlsxTrapUserAttributeChangeType OBJECT-TYPE This object represents type of the configuration change. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.103 | ArubaConfigurationChangeType | accessible-for-notify | current |
| wlsxTrapApControllerIp OBJECT-TYPE IP address of the controller to which the AP is (or was most recently) registered. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.104 | IpAddress | accessible-for-notify | current |
| wlsxTrapApMasterStatus OBJECT-TYPE Status of the AP as seen by the master when the status changes. **NOTE: this object is deprecated and replaced by wlsxTrapApConductorStatus | 1.3.6.1.4.1.14823.2.3.3.1.200.1.105 | ArubaAPMasterStatus | accessible-for-notify | deprecated |
| wlsxTrapCaName OBJECT-TYPE This object is used in the traps to indicate the name of the trustpoint. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.106 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapCrlName OBJECT-TYPE This object is used in the traps to indicate the name of the crl. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.107 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapCount OBJECT-TYPE This object represents the number of occurrence of this trap. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.108 | Integer32 | accessible-for-notify | current |
| wlsxTrapAPPreviousUplinkType OBJECT-TYPE This object specifies the up link type for an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.130 | ArubaAPUplinkType | accessible-for-notify | current |
| wlsxTrapAPPreviousUplinkActiveTime OBJECT-TYPE This object specifies the up link type for an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.131 | TimeTicks | accessible-for-notify | current |
| wlsxTrapAPActiveUplinkType OBJECT-TYPE This object specifies the up link type for an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.132 | ArubaAPUplinkType | accessible-for-notify | current |
| wlsxTrapAPUplinkChangeReason OBJECT-TYPE This object specifies the up link change reason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.133 | ArubaAPUplinkChangeReason | accessible-for-notify | current |
| wlsxTrapAPManagedModeConfigFailure OBJECT-TYPE This object indicates the error for the failure of config apply on IAP. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.138 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapAuthServerAddress OBJECT-TYPE This object is used in the traps to indicate the Authentication Server IP used for Authentication. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.139 | IpAddress | accessible-for-notify | current |
| wlsxTrapPortalServerName OBJECT-TYPE This object is used in the traps to indicate the Captive Portal Server used for Authentication. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.140 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapPortalServerAddress OBJECT-TYPE This object is used in the traps to indicate the Captive Portal Server IP or host name used for Authentication. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.141 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapPortalServerDownReason OBJECT-TYPE This object specifies the captive portal server down reason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.142 | ArubaPortalServerDownReason | accessible-for-notify | current |
| wlsxTrapStationBlackListReasonStr OBJECT-TYPE This object is used in the traps to indicate the type of Blacklist reason. **NOTE: this object is deprecated and replaced by wlsxTrapStationDenyListReasonStr. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.144 | DisplayString (SIZE(0..32)) | accessible-for-notify | deprecated |
| wlsxTrapAPUSBStatus OBJECT-TYPE This object represents plug in or plug out status of an USB device. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.147 | DisplayString (SIZE(0..32)) | accessible-for-notify | current |
| wlsxTrapUSBVendorProductID OBJECT-TYPE This object represents vendor ID or product ID of an USB device. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.148 | DisplayString (SIZE(0..32)) | accessible-for-notify | current |
| wlsxTrapAuthFailureReason OBJECT-TYPE This object represents the reason for the authentication failure. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.155 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapStationDenyListReason OBJECT-TYPE The Reason for which a station is in deny list. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.156 | ArubaDenyListReason | accessible-for-notify | current |
| wlsxTrapStationDenyListReasonStr OBJECT-TYPE This object is used in the traps to indicate the type of Denylist reason. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.157 | DisplayString (SIZE(0..32)) | accessible-for-notify | current |
| wlsxTrapConductorIp OBJECT-TYPE This object represents the conductor IP address. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.158 | IpAddress | accessible-for-notify | current |
| wlsxTrapConductorName OBJECT-TYPE This object represents the conductor controller name. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.159 | DisplayString (SIZE(0..64)) | accessible-for-notify | current |
| wlsxTrapApConductorStatus OBJECT-TYPE Status of the AP as seen by the conductor when the status changes. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.160 | ArubaAPConductorStatus | accessible-for-notify | current |
| wlsxTrapAPHTMode OBJECT-TYPE This object represents HT-Mode Information. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.161 | ArubaHTMode | accessible-for-notify | current |
| wlsxTrapAPPhyType OBJECT-TYPE This object represents Band Information. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.162 | ArubaPhyType | accessible-for-notify | current |
| wlsxTrapAPPrevHTMode OBJECT-TYPE This object represents Previous HT-Mode Information. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.163 | ArubaHTMode | accessible-for-notify | current |
| wlsxTrapAPPrevPhyType OBJECT-TYPE This object represents Prev Band Information. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.164 | ArubaPhyType | accessible-for-notify | current |
| wlsxTrapAPSecChannel OBJECT-TYPE This object represents Secondary Channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.1.165 | Integer32 | accessible-for-notify | current |
| aiTrapDefinitionsGroup OBJECT-IDENTITY | 1.3.6.1.4.1.14823.2.3.3.1.200.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| wlsxNodeRateAnomaly NOTIFICATION-TYPE This trap indicates that a node is exceeding the threshold set for the frame type. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1003 | current |
| wlsxNUserEntryCreated NOTIFICATION-TYPE This trap indicates that a new user was created. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1014 | current |
| wlsxNUserEntryDeleted NOTIFICATION-TYPE This trap indicates that a user was deleted. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1015 | current |
| wlsxNUserEntryAuthenticated NOTIFICATION-TYPE This trap indicates that a user is Authenticated. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1016 | current |
| wlsxNUserEntryDeAuthenticated NOTIFICATION-TYPE This trap indicates that a user is Deauthenticated. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1017 | current |
| wlsxNUserAuthenticationFailed NOTIFICATION-TYPE This trap indicates that a user authentication has failed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1018 | current |
| wlsxNAuthServerReqTimedOut NOTIFICATION-TYPE This trap indicates that the authentication server request timed out. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1019 | current |
| wlsxNAuthServerTimedOut NOTIFICATION-TYPE This trap indicates that the authentication server timed out. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1020 | current |
| wlsxNAuthServerIsUp NOTIFICATION-TYPE This trap indicates that an authentication server is up. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1021 | current |
| wlsxNAccessPointIsUp NOTIFICATION-TYPE A Trap which indicates that an access point up. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1040 | current |
| wlsxNAccessPointIsDown NOTIFICATION-TYPE A Trap which indicates that an access point down. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1041 | current |
| wlsxNChannelChanged NOTIFICATION-TYPE This trap indicates that an access point at Location wlsxTrapAPLocation has changed the channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1043 | current |
| wlsxNStationAddedToBlackList NOTIFICATION-TYPE This trap indicates that the station is black listed. **NOTE: this notification is deprecated and replaced by wlsxNStationAddedToDenyList. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1044 | deprecated |
| wlsxNStationRemovedFromBlackList NOTIFICATION-TYPE This trap indicates that the station is removed from the black list. **NOTE: this notification is deprecated and replaced by wlsxNStationRemovedFromDenyList | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1045 | deprecated |
| wlsxNRadioAttributesChanged NOTIFICATION-TYPE A Trap which indicates changes in the Radio attributes of an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1049 | current |
| wlsxUnsecureAPDetected NOTIFICATION-TYPE This trap indicates that an unauthorized access point is connected to the wired network. The access point is declared Rogue because it was matched to a MAC address. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1053 | current |
| wlsxUnsecureAPResolved NOTIFICATION-TYPE This trap indicates that a previously detected access point, classified as Rogue, is no longer present in the network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1054 | current |
| wlsxStaImpersonation NOTIFICATION-TYPE This trap indicates that an AM detected Station Impersonation. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1055 | current |
| wlsxReservedChannelViolation NOTIFICATION-TYPE This trap indicates that an AM detected an access point which is violating the Reserved Channel configuration. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1056 | current |
| wlsxValidSSIDViolation NOTIFICATION-TYPE This trap indicates that an AP has detected an access point is violating Valid SSID configuration by using an SSID that is reserved for use by a valid AP only. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1057 | current |
| wlsxChannelMisconfiguration NOTIFICATION-TYPE This trap indicates that an AP detected an access point that has a channel misconfiguration because it is using a channel that is not valid. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1058 | current |
| wlsxOUIMisconfiguration NOTIFICATION-TYPE This trap indicates that an AP detected an access point that has an OUI misconfiguration because it is using an OUI that is not valid. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1059 | current |
| wlsxSSIDMisconfiguration NOTIFICATION-TYPE This trap indicates that an AP detected an access point that has an SSID misconfiguration because it is using an SSID that is not valid. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1060 | current |
| wlsxShortPreableMisconfiguration NOTIFICATION-TYPE This trap indicates that an access point has bad Short preamble configuration. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1061 | current |
| wlsxWPAMisconfiguration NOTIFICATION-TYPE This trap indicates that an AP detected an access point that is misconfigured because it is not using WPA. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1062 | current |
| wlsxAdhocNetworkDetected NOTIFICATION-TYPE This trap indicates that an AM has detected an Ad hoc network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1063 | current |
| wlsxAdhocNetworkRemoved NOTIFICATION-TYPE This trap indicates that a previously detected Ad hoc Network is no longer present in the network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1064 | current |
| wlsxStaPolicyViolation NOTIFICATION-TYPE This trap indicates that Protection was enforced because a valid station's association to a non-valid access point violated Valid Station policy. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1065 | current |
| wlsxRepeatWEPIVViolation NOTIFICATION-TYPE This trap indicates that an AP detected that a valid access point is using the same WEP initialization vector in consecutive packets. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1066 | current |
| wlsxWeakWEPIVViolation NOTIFICATION-TYPE This trap indicates that an AP detected that a valid access point is using a Weak WEP initialization vector. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1067 | current |
| wlsxChannelInterferenceDetected NOTIFICATION-TYPE This trap indicates that an AP has detected channel interference. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1068 | current |
| wlsxChannelInterferenceCleared NOTIFICATION-TYPE This trap indicates that a previously detected channel interference is no longer present. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1069 | current |
| wlsxAPInterferenceDetected NOTIFICATION-TYPE This trap indicates that an AP has detected interference for an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1070 | current |
| wlsxAPInterferenceCleared NOTIFICATION-TYPE This trap indicates that the previously detected interference for an access point is no longer present. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1071 | current |
| wlsxStaInterferenceDetected NOTIFICATION-TYPE This trap indicates that an AP has detected interference for a station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1072 | current |
| wlsxStaInterferenceCleared NOTIFICATION-TYPE This trap indicates that the previously detected interference for a station is no longer present. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1073 | current |
| wlsxFrameRetryRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Retry Rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1074 | current |
| wlsxFrameReceiveErrorRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Receive Error Rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1075 | current |
| wlsxFrameFragmentationRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that an access point exceeded the configured upper threshold for Frame Fragmentation Rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1076 | current |
| wlsxFrameBandWidthRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that a station or access point has exceeded the configured upper threshold for Bandwidth rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1077 | current |
| wlsxFrameLowSpeedRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Low speed rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1078 | current |
| wlsxFrameNonUnicastRateExceeded NOTIFICATION-TYPE This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Non Unicast traffic rate. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1079 | current |
| wlsxLoadbalancingEnabled NOTIFICATION-TYPE This trap indicates that an AM is reporting that an AP has enabled Load balancing. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1080 | current |
| wlsxLoadbalancingDisabled NOTIFICATION-TYPE This trap indicates that an AM is reporting that an AP has enabled Load balancing. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1081 | current |
| wlsxChannelFrameRetryRateExceeded NOTIFICATION-TYPE This trap indicates that an AP has detected that the configured upper threshold for Frame Retry Rate was exceeded on a channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1082 | current |
| wlsxChannelFrameFragmentationRateExceeded NOTIFICATION-TYPE This trap indicates that an AP has detected that the configured upper threshold for Frame Fragmentation Rate was exceeded on a channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1083 | current |
| wlsxChannelFrameErrorRateExceeded NOTIFICATION-TYPE This trap indicates that an AP has detected that the configured upper threshold for Frame Receive Error Rate was exceeded on a channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1084 | current |
| wlsxSignatureMatchAP NOTIFICATION-TYPE This trap indicates that an AP detected a signature match in a frame from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1085 | current |
| wlsxSignatureMatchSta NOTIFICATION-TYPE This trap indicates that an AP detected a signature match in a frame from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1086 | current |
| wlsxChannelRateAnomaly NOTIFICATION-TYPE This trap indicates that an AP detected frames on a channel which exceed the configured IDS rate threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1087 | current |
| wlsxNodeRateAnomalyAP NOTIFICATION-TYPE This trap indicates that an AP detected frames transmitted or received by an access point, which exceed the configured IDS rate threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1088 | current |
| wlsxNodeRateAnomalySta NOTIFICATION-TYPE This trap indicates that an AP detected frames transmitted or received by a node, which exceed the configured IDS rate threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1089 | current |
| wlsxEAPRateAnomaly NOTIFICATION-TYPE This trap indicates that the rate of EAP Handshake packets received by an AP has exceeded the configured IDS EAP Handshake rate threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1090 | current |
| wlsxSignalAnomaly NOTIFICATION-TYPE This trap indicates that an AM detected a Signal Anomaly. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1091 | current |
| wlsxSequenceNumberAnomalyAP NOTIFICATION-TYPE This trap indicates that an AM received packets from an AP which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1092 | current |
| wlsxSequenceNumberAnomalySta NOTIFICATION-TYPE This trap indicates that an AM received packets from a Node which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1093 | current |
| wlsxDisconnectStationAttack NOTIFICATION-TYPE This trap indicates that an AM detected a station Disconnect attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1094 | current |
| wlsxApFloodAttack NOTIFICATION-TYPE This trap indicates that the number of potential fake APs detected by an AP has exceeded the configured IDS threshold. This is the total number of fake APs observed across all bands. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1095 | current |
| wlsxAdhocNetwork NOTIFICATION-TYPE This trap indicates that an AM detected an Ad hoc Network. An Station is connected to an ad hoc AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1096 | current |
| wlsxWirelessBridge NOTIFICATION-TYPE This trap indicates that an AP detected a Wireless Bridge when a WDS frame was seen between the transmitter and receiver addresses. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1097 | current |
| wlsxInvalidMacOUIAP NOTIFICATION-TYPE This trap indicates that an AP detected an invalid MAC OUI in the BSSID of a frame. An invalid MAC OUI suggests that the frame may be spoofed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1098 | current |
| wlsxInvalidMacOUISta NOTIFICATION-TYPE This trap indicates that an AP detected an invalid MAC OUI in the SRC or DST address of a frame. An invalid MAC OUI suggests that the frame may be spoofed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1099 | current |
| wlsxWEPMisconfiguration NOTIFICATION-TYPE This trap indicates that an AP detected an access point that is misconfigured because it does not have Privacy enabled. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1100 | current |
| wlsxStaRepeatWEPIVViolation NOTIFICATION-TYPE This trap indicates that an AP detected that a valid station is using the same WEP initialization vector in consecutive packets. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1101 | current |
| wlsxStaWeakWEPIVViolation NOTIFICATION-TYPE This trap indicates that an AP detected that a valid station is using a Weak WEP initialization vector. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1102 | current |
| wlsxStaAssociatedToUnsecureAP NOTIFICATION-TYPE This trap indicates that an AM detected a client associated with a Rogue access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1103 | current |
| wlsxStaUnAssociatedFromUnsecureAP NOTIFICATION-TYPE This trap indicates that a previously detected rogue access point association is no longer present. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1104 | current |
| wlsxAdhocNetworkBridgeDetected NOTIFICATION-TYPE This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1105 | current |
| wlsxInterferingApDetected NOTIFICATION-TYPE This trap indicates that an AP detected an access point classified as Interfering. The access point is declared Interfering because it is neither authorized or classified as Rogue. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1106 | current |
| wlsxColdStart NOTIFICATION-TYPE An enterprise version of cold start trap, which contains the controller time stamp. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1111 | current |
| wlsxWarmStart NOTIFICATION-TYPE An enterprise version of warm start trap, which contains the controller time stamp. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1112 | current |
| wlsxAPImpersonation NOTIFICATION-TYPE This trap indicates that an AP detected AP Impersonation because the number of beacons seen has exceeded the expected number by the configured percentage threshold. The expected number is calculated based on the Beacon Interval Field in the Beacon frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1113 | current |
| wlsxNAuthServerIsDown NOTIFICATION-TYPE This trap indicates that an authentication server is down. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1115 | current |
| wlsxWindowsBridgeDetected NOTIFICATION-TYPE This trap indicates that an AM has detected a station that is bridging from a wireless network to a wired network | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1129 | current |
| wlsxSignAPNetstumbler NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Netstumbler from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1134 | current |
| wlsxSignStaNetstumbler NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Netstumbler from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1135 | current |
| wlsxSignAPAsleap NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for ASLEAP from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1136 | current |
| wlsxSignStaAsleap NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for ASLEAP from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1137 | current |
| wlsxSignAPAirjack NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for AirJack from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1138 | current |
| wlsxSignStaAirjack NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for AirJack from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1139 | current |
| wlsxSignAPNullProbeResp NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Null-Probe-Response from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1140 | current |
| wlsxSignStaNullProbeResp NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Null-Probe-Response from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1141 | current |
| wlsxSignAPDeauthBcast NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Deauth-Broadcast from an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1142 | current |
| wlsxSignStaDeauthBcast NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Deauth-Broadcast from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1143 | current |
| wlsxWindowsBridgeDetectedAP NOTIFICATION-TYPE This trap indicates that an AP is detecting an access point that is bridging from a wireless network to a wired network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1144 | current |
| wlsxWindowsBridgeDetectedSta NOTIFICATION-TYPE This trap indicates that an AP is detecting a station that is bridging from a wireless network to a wired network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1145 | current |
| wlsxAdhocNetworkBridgeDetectedAP NOTIFICATION-TYPE This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1146 | current |
| wlsxAdhocNetworkBridgeDetectedSta NOTIFICATION-TYPE This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1147 | current |
| wlsxDisconnectStationAttackAP NOTIFICATION-TYPE This trap indicates that an AM detected a station disconnect attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1148 | current |
| wlsxDisconnectStationAttackSta NOTIFICATION-TYPE This trap indicates that an AM detected a station Disconnect attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1149 | current |
| wlsxSuspectUnsecureAPDetected NOTIFICATION-TYPE This trap indicates that an access point, classified as Suspected Rogue, has been detected by a Controller. The AP is suspected to be rogue, with the supplied confidence level, because it was matched to the wired MAC address. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1150 | current |
| wlsxSuspectUnsecureAPResolved NOTIFICATION-TYPE This trap indicates that a previously detected access point, classified Suspected Rogue, is either no longer present in the network or has changed its state. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1151 | current |
| wlsxHtGreenfieldSupported NOTIFICATION-TYPE This trap indicates that an AP detected an access point that supports HT Greenfield mode. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1157 | current |
| wlsxHT40MHzIntoleranceAP NOTIFICATION-TYPE This trap indicates that an AP is detecting an access point with the HT 40MHz intolerance setting. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1158 | current |
| wlsxHT40MHzIntoleranceSta NOTIFICATION-TYPE This trap indicates that the system is detecting an HT 40MHz Intolerance setting from a Station. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1159 | current |
| wlsxNAuthServerAllInService NOTIFICATION-TYPE This trap indicates that all authentication servers is a server group are brought back in service. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1160 | current |
| wlsxNAdhocNetwork NOTIFICATION-TYPE This trap indicates that an AP detected an ad hoc network where a station is connected to an ad hoc access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1161 | current |
| wlsxNAdhocNetworkBridgeDetectedAP NOTIFICATION-TYPE This trap indicates that an AP detected an ad hoc network that is bridging to a wired network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1162 | current |
| wlsxNAdhocNetworkBridgeDetectedSta NOTIFICATION-TYPE This trap indicates that an AP detected an ad hoc network that is bridging to a wired network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1163 | current |
| wlsxClientFloodAttack NOTIFICATION-TYPE This trap indicates that the number of potential fake clients detected by an AP has exceeded the configured IDS threshold. This is the total number of fake clients observed across all bands. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1170 | current |
| wlsxValidClientNotUsingEncryption NOTIFICATION-TYPE This trap indicates that an AP detected an unencrypted data frame between a valid client and an access point. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1171 | current |
| wlsxAdhocUsingValidSSID NOTIFICATION-TYPE This trap indicates that an AP detected an ad hoc network using a valid/protected SSID. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1172 | current |
| wlsxAPSpoofingDetected NOTIFICATION-TYPE This trap indicates that an AP detected that one of its virtual APs is being spoofed using MAC spoofing. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1173 | current |
| wlsxClientAssociatingOnWrongChannel NOTIFICATION-TYPE This trap indicates that an AP detected a client trying to associate to one of its BSSIDs on the wrong channel. This can be a sign that the BSSID is being spoofed in order to fool the client into thinking the AP is operating on another channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1174 | current |
| wlsxNDisconnectStationAttack NOTIFICATION-TYPE This trap indicates that an AP has determined that a client is under Disconnect Attack because the rate of Assoc/Reassoc Response packets received by that client exceeds the configured threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1175 | current |
| wlsxNStaUnAssociatedFromUnsecureAP NOTIFICATION-TYPE This trap indicates that an AP that had previously detected a client association to a Rogue access point is no longer detecting that association. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1176 | current |
| wlsxOmertaAttack NOTIFICATION-TYPE This trap indicates that an AP detected an Omerta attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1177 | current |
| wlsxTKIPReplayAttack NOTIFICATION-TYPE This trap indicates that an AP detected a TKIP replay attack. If successful this could be the precursor to more advanced attacks. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1178 | current |
| wlsxChopChopAttack NOTIFICATION-TYPE This trap indicates that an AP detected a ChopChop attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1179 | current |
| wlsxFataJackAttack NOTIFICATION-TYPE This trap indicates that an AP detected a FATA-Jack attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1180 | current |
| wlsxInvalidAddressCombination NOTIFICATION-TYPE This trap indicates that an AP detected an invalid source and destination combination. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1181 | current |
| wlsxValidClientMisassociation NOTIFICATION-TYPE This trap indicates that an AP detected a misassociation between a valid client and an unsafe AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1182 | current |
| wlsxMalformedHTIEDetected NOTIFICATION-TYPE This trap indicates that an AP detected a malformed HT Information Element. This can be the result of a misbehaving wireless driver or it may be an indication of a new wireless attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1183 | current |
| wlsxMalformedAssocReqDetected NOTIFICATION-TYPE This trap indicates that an AP detected a malformed association request with a NULL SSID. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1184 | current |
| wlsxOverflowIEDetected NOTIFICATION-TYPE This trap indicates that an AP detected a management frame with a malformed information element. The declared length of the element is larger than the entire frame containing the element. This may be used to corrupt or crash wireless drivers. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1185 | current |
| wlsxOverflowEAPOLKeyDetected NOTIFICATION-TYPE This trap indicates that an AP detected a key in an EAPOL Key message with a specified length greater than the length of the entire message. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1186 | current |
| wlsxMalformedFrameLargeDurationDetected NOTIFICATION-TYPE This trap indicates that an AP detected an unusually large duration in a wireless frame. This may be an attempt to block other devices from transmitting. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1187 | current |
| wlsxMalformedFrameWrongChannelDetected NOTIFICATION-TYPE This trap indicates that an AP detected a beacon on one channel advertising another channel. This could be an attempt to lure clients away from a valid AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1188 | current |
| wlsxMalformedAuthFrame NOTIFICATION-TYPE This trap indicates that an AP detected an authentication frame with either a bad algorithm (similar to Fata-Jack) or a bad transaction. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1189 | current |
| wlsxCTSRateAnomaly NOTIFICATION-TYPE This trap indicates that the rate of CTS packets received by an AP exceeds the configured IDS threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1190 | current |
| wlsxRTSRateAnomaly NOTIFICATION-TYPE This trap indicates that the rate of RTS packets received by an AP exceeds the configured IDS threshold. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1191 | current |
| wlsxNRogueAPDetected NOTIFICATION-TYPE This trap indicates that an unauthorized access point is connected to the wired network. The access point is classified as Rogue by the system. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1192 | current |
| wlsxNRogueAPResolved NOTIFICATION-TYPE This trap indicates that a previously detected access point, classified as Rogue, is either no longer present in the network or it changed its state. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1193 | current |
| wlsxNeighborAPDetected NOTIFICATION-TYPE This trap indicates that an access point has been classified as a Neighbor by the system. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1194 | current |
| wlsxNInterferingAPDetected NOTIFICATION-TYPE This trap indicates that an access point has been classified as Interfering by the system. The access point is declared Interfering because it is not authorized, nor has it been classified as a Rogue. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1195 | current |
| wlsxNSuspectRogueAPDetected NOTIFICATION-TYPE This trap indicates that an access point, classified as Suspected Rogue, is detected by the system. The AP is suspected to be rogue with the supplied confidence level. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1196 | current |
| wlsxNSuspectRogueAPResolved NOTIFICATION-TYPE This trap indicates that a previously detected access point, classified as Suspected Rogue, is either no longer present in the network or has changed its state. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1197 | current |
| wlsxBlockAckAttackDetected NOTIFICATION-TYPE This trap indicates that an attempt has been made to deny service to the source address by spoofing a block ACK add request that sets a sequence number window outside the currently used window. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1198 | current |
| wlsxHotspotterAttackDetected NOTIFICATION-TYPE This trap indicates that a new AP has appeared immediately following a client probe request. This is indicative of the Hotspotter tool or similar that attempts to trap clients with a fake hotspot or other wireless network. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1199 | current |
| wlsxNSignatureMatch NOTIFICATION-TYPE This trap indicates that an AP detected a signature match in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1200 | current |
| wlsxNSignatureMatchNetstumbler NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Netstumbler in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1201 | current |
| wlsxNSignatureMatchAsleap NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for ASLEAP in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1202 | current |
| wlsxNSignatureMatchAirjack NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Airjack in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1203 | current |
| wlsxNSignatureMatchNullProbeResp NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Null-Probe-Response in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1204 | current |
| wlsxNSignatureMatchDeauthBcast NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Deauth-Broadcast in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1205 | current |
| wlsxNSignatureMatchDisassocBcast NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Disassoc-Broadcast in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1206 | current |
| wlsxNSignatureMatchWellenreiter NOTIFICATION-TYPE This trap indicates that an AP detected a signature match for Wellenreiter in a frame. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1207 | current |
| wlsxAPDeauthContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain an access point by disconnecting its client. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1208 | current |
| wlsxClientDeauthContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain a client by disconnecting it from the AP that it is associated with. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1209 | current |
| wlsxAPWiredContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1210 | current |
| wlsxClientWiredContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1211 | current |
| wlsxAPTaggedWiredContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1212 | current |
| wlsxClientTaggedWiredContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1213 | current |
| wlsxTarpitContainment NOTIFICATION-TYPE This trap indicates that an AP has attempted to contain an access point by moving a client that is attempting to associate to it to a tarpit. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1214 | current |
| wlsxAPChannelChange NOTIFICATION-TYPE This trap indicates that an AP changed its channel. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1216 | current |
| wlsxAPPowerChange NOTIFICATION-TYPE This trap indicates that an AP changed its transmit power level. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1217 | current |
| wlsxAPModeChange NOTIFICATION-TYPE This trap indicates that an AP changed its mode from AP to APMonitor or vice versa. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1218 | current |
| wlsxUserEntryAttributesChanged NOTIFICATION-TYPE This trap indicates that the user entry attributes have changed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1219 | current |
| wlsxPowerSaveDosAttack NOTIFICATION-TYPE This trap indicates that an AP detected a Power Save DoS attack. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1220 | current |
| wlsxNAPMasterStatusChange NOTIFICATION-TYPE This trap indicates that the status of the AP as seen by the master controller has changed. **NOTE: this notification is deprecated and replaced by wlsxNAPConductorStatusChange | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1221 | deprecated |
| wlsxNAdhocUsingValidSSID NOTIFICATION-TYPE This trap indicates that an AP detected an ad hoc network node using a valid/protected SSID. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1222 | current |
| wlsxMgmtUserAuthenticationFailed NOTIFICATION-TYPE This trap indicates that a management user authentication has failed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1224 | current |
| wlsxAPActiveUplinkChanged NOTIFICATION-TYPE When the active uplink of an AP changes, a notification is sent to the Management Entity with the new uplink type | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1252 | current |
| wlsxAPManagedModeConfigFailureTrap NOTIFICATION-TYPE Indicated failure in applying config. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1255 | current |
| wlsxNAuthServerAcctTimedOut NOTIFICATION-TYPE This trap indicates that the authentication server accounting timed out. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1256 | current |
| wlsxPortalServerDown NOTIFICATION-TYPE This trap indicates that the portal server is down. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1259 | current |
| wlsxPortalServerUp NOTIFICATION-TYPE This trap indicates that the portal server is up. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1260 | current |
| wlsxIAPVoiceClientLocationUpdate NOTIFICATION-TYPE The trap represents a IAP voice client location update. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1262 | current |
| wlsxWPAFTAttack NOTIFICATION-TYPE This trap indicates there is a possible attack of the Fast BSS Transition causing a WPA key re-installation. This can be indicative of a security breach where an attacker can hijack a client's association and/or decrypt an otherwise secure connection. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1267 | current |
| wlsxMitMDetected NOTIFICATION-TYPE This trap indicates that an AP detected a possible channel-based Man in the Middle attack by someone using spoofed beacons with an invalid Channel Switch Announcement. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1268 | current |
| wlsxAPLoopDetected NOTIFICATION-TYPE This trap indicates that loop is detected on AP's secure jack port. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1271 | current |
| wlsxAPBROADCASTSTORM NOTIFICATION-TYPE This trap indicates that broadcast storm is detected on AP's secure jack port. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1272 | current |
| wlsxCLEARPASSSERVERINVALID NOTIFICATION-TYPE This trap indicates that clearpass server is not valid when using the CA to verity the server for download-role. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1274 | current |
| wlsxAPUSBPLUGALARM NOTIFICATION-TYPE This trap indicates that an USB device is plugged in or out to an AP. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1277 | current |
| wlsxClientRejectedByMaxClientCount NOTIFICATION-TYPE This trap indicates the client is rejected by the max client count. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1284 | current |
| wlsxClientPskAuthenticationFailed NOTIFICATION-TYPE This trap indicates the client PSK Authentication Failed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1285 | current |
| wlsxNStationAddedToDenyList NOTIFICATION-TYPE This trap indicates that the station is in deny list. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1286 | current |
| wlsxNStationRemovedFromDenyList NOTIFICATION-TYPE This trap indicates that the station is removed from the deny list. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1287 | current |
| wlsxNAPConductorStatusChange NOTIFICATION-TYPE This trap indicates that the status of the AP as seen by the conductor controller has changed. | 1.3.6.1.4.1.14823.2.3.3.1.200.2.1288 | current |