AH-TRAP-MIB
- Registered at
- 1.3.6.1.4.1.26928.1.1.1.1.11.3.6.1.4.1.26928.1.1.1.1.2
- Last updated
- 2006-12-14 00:00
- Organization
- Aerohive Networks, Inc.
- Namespace
- aerohive
- Source file
AH-TRAP-MIB- Digest
sha256:6be349fb07a0931bbc76789ca5a9ee668ad5926219bfb5abd541a2fdd6bd5579
Description
This is the MIB module for access point trap definitions for Aerohive Networks Inc.
Contact
See AH-SMI-MIB for information.
Imports
| From | Symbols |
|---|---|
| AH-SMI-MIB | AhMACProtocol, AhNodeID, AhString, ahAPTrap |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TruthValue, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
AH-SMI-MIB AH-TRAP-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| AhAuthenticationMethod TEXTUAL-CONVENTION Authentication method supported by the HiveAP | current | |||
| AhEncrytionMethod TEXTUAL-CONVENTION Encryption method supported by the HiveAP | current | |||
| AhProbableCause TEXTUAL-CONVENTION It defines the probable cause for a problem on the HiveAP. | current | |||
| AhState TEXTUAL-CONVENTION It defines the state for interfaces. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ahNotificationVarBind OBJECT-IDENTITY | 1.3.6.1.4.1.26928.1.1.1.1.2 | |||
| ahAPId OBJECT-TYPE It is the node ID (MAC address in hexadecimal format) of the HiveAP where the trap is generated. If a HiveAP is configured with 2 hives, the node ID is the first MAC address of the management interface. | 1.3.6.1.4.1.26928.1.1.1.1.2.1 | AhNodeID | not-accessible | current |
| ahAPName OBJECT-TYPE The host name of the HiveAP where the trap is generated. | 1.3.6.1.4.1.26928.1.1.1.1.2.2 | AhString | not-accessible | current |
| ahSeverity OBJECT-TYPE It contains the serverity of the trap. | 1.3.6.1.4.1.26928.1.1.1.1.2.3 | INTEGER {undetermined(1), info(2), minor(3), major(4), critical(5)} | not-accessible | current |
| ahObjectName OBJECT-TYPE It describes the object for which the trap is generated. | 1.3.6.1.4.1.26928.1.1.1.1.2.4 | DisplayString (SIZE(0..64)) | not-accessible | current |
| ahProbableCause OBJECT-TYPE It describes the probable cause of a problem. | 1.3.6.1.4.1.26928.1.1.1.1.2.5 | AhProbableCause | not-accessible | current |
| ahCurValue OBJECT-TYPE It contains the current value of a threshold counter. | 1.3.6.1.4.1.26928.1.1.1.1.2.6 | INTEGER | not-accessible | current |
| ahThresholdHigh OBJECT-TYPE It contains the value for a high threshold. | 1.3.6.1.4.1.26928.1.1.1.1.2.7 | INTEGER | not-accessible | current |
| ahThresholdLow OBJECT-TYPE It contains the value for a low threshold. | 1.3.6.1.4.1.26928.1.1.1.1.2.8 | INTEGER | not-accessible | current |
| ahPreviousState OBJECT-TYPE It contains the value for a previous state. | 1.3.6.1.4.1.26928.1.1.1.1.2.9 | AhState | not-accessible | current |
| ahCurrentState OBJECT-TYPE It contains the value for the current state. | 1.3.6.1.4.1.26928.1.1.1.1.2.10 | AhState | not-accessible | current |
| ahTrapDesc OBJECT-TYPE It contains the description of the trap. | 1.3.6.1.4.1.26928.1.1.1.1.2.11 | DisplayString | not-accessible | current |
| ahCode OBJECT-TYPE It contains access information to the Aerohive logging/action dictionary. | 1.3.6.1.4.1.26928.1.1.1.1.2.12 | Integer32 | not-accessible | current |
| ahIfIndex OBJECT-TYPE The interface index used to identify uniquely an interface (logical or physical). | 1.3.6.1.4.1.26928.1.1.1.1.2.13 | Integer32 | not-accessible | current |
| ahObjectType OBJECT-TYPE It specifies the object type: a client link or a neighbor link. | 1.3.6.1.4.1.26928.1.1.1.1.2.14 | INTEGER {clientLink(1), neighborLink(2)} | not-accessible | current |
| ahRemoteId OBJECT-TYPE It is the MAC address of the remote node. If the remote node is a HiveAP, the ID must be the MAC address of its management interface. If the remote node is a client station, it must be the MAC address of the client. | 1.3.6.1.4.1.26928.1.1.1.1.2.15 | AhNodeID | not-accessible | current |
| ahIDPType OBJECT-TYPE It is used to indicate the AP identified is a rogue, or valid, or compliant, or noncompliant, or external AP. | 1.3.6.1.4.1.26928.1.1.1.1.2.16 | INTEGER {rogue(1), valid(2), external(3)} | not-accessible | current |
| ahIDPChannel OBJECT-TYPE It is the channel number used by the identified AP. | 1.3.6.1.4.1.26928.1.1.1.1.2.17 | Integer32 | not-accessible | current |
| ahIDPRSSI OBJECT-TYPE It is the RSSI for the identified AP or Client. | 1.3.6.1.4.1.26928.1.1.1.1.2.18 | Integer32 | not-accessible | current |
| ahIDPCompliance OBJECT-TYPE It is bit mask to indicate which policy the indentified AP is compliant with (bit is set if it is NOT compliant). | 1.3.6.1.4.1.26928.1.1.1.1.2.19 | INTEGER {open-policy(1), wep-policy(2), wpa-policy(4), wmm-policy(8), oui-policy(16), ssid-policy(32), short-preamble-policy(64), short-beacon-policy(128), ad-hoc-policy(256)} | not-accessible | current |
| ahSSID OBJECT-TYPE It contains the SSID name for the detected AP. | 1.3.6.1.4.1.26928.1.1.1.1.2.20 | DisplayString (SIZE(0..32)) | not-accessible | current |
| ahStationType OBJECT-TYPE It indicates whether it is event for a peer AP or client PC | 1.3.6.1.4.1.26928.1.1.1.1.2.21 | INTEGER {station-ap(1), station-client(2)} | not-accessible | current |
| ahIDPStationData OBJECT-TYPE It is bit mask to indicate policies are detected for the identified AP . Note: the oui-policy and ssid-policy are omitted due to the presence of the ahRemoteID, and SSID in the trap message. | 1.3.6.1.4.1.26928.1.1.1.1.2.22 | INTEGER {open-policy(1), wep-policy(2), wpa-policy(4), wmm-policy(8), short-preamble-policy(64), short-beacon-policy(128), ad-hoc-policy(256)} | not-accessible | current |
| ahRemoved OBJECT-TYPE It indicates whether the AP or client can not be detected. | 1.3.6.1.4.1.26928.1.1.1.1.2.23 | INTEGER {removed-false(0), removed-true(1)} | not-accessible | current |
| ahClientMAC OBJECT-TYPE It contains the MAC address of the wireless client. It is required. | 1.3.6.1.4.1.26928.1.1.1.1.2.24 | AhNodeID | not-accessible | current |
| ahCLientIP OBJECT-TYPE It contains the IP address of the wireless client. It is optional. | 1.3.6.1.4.1.26928.1.1.1.1.2.25 | DisplayString | not-accessible | current |
| ahClientHostName OBJECT-TYPE It contains the host name of the wireless client. It is optional. | 1.3.6.1.4.1.26928.1.1.1.1.2.26 | DisplayString | not-accessible | current |
| ahClientUserName OBJECT-TYPE It contains the user name of the wireless client. It is optional. | 1.3.6.1.4.1.26928.1.1.1.1.2.27 | DisplayString | not-accessible | current |
| ahPowerSrc OBJECT-TYPE It indicates whether the power source is from the power adaptor or PoE. If the power source is the adaptor, PoE information in the trap is ignored. | 1.3.6.1.4.1.26928.1.1.1.1.2.28 | INTEGER {adaptor(0), poe(1)} | not-accessible | current |
| ahPoEEth0On OBJECT-TYPE It indicates whether PoE is on eth0 or not. | 1.3.6.1.4.1.26928.1.1.1.1.2.29 | TruthValue | not-accessible | current |
| ahPoEEth0Pwr OBJECT-TYPE It indicates the power level of PoE in watts multiply by 10. | 1.3.6.1.4.1.26928.1.1.1.1.2.30 | INTEGER | not-accessible | current |
| ahPoEEth1On OBJECT-TYPE It indicates whether PoE is on eth1 or not. | 1.3.6.1.4.1.26928.1.1.1.1.2.31 | TruthValue | not-accessible | current |
| ahPoEEth1Pwr OBJECT-TYPE It indicates the power level of PoE on eht1 in watts multiply by 10. | 1.3.6.1.4.1.26928.1.1.1.1.2.32 | INTEGER | not-accessible | current |
| ahRadioChannel OBJECT-TYPE It is the channel number currently in use for this radio. | 1.3.6.1.4.1.26928.1.1.1.1.2.33 | Integer32 | read-only | current |
| ahRadioTxPower OBJECT-TYPE It is the transmit power in dBm that the radio is currently using. The range is 0 to 20 dBm. | 1.3.6.1.4.1.26928.1.1.1.1.2.34 | Integer32 | read-only | current |
| ahClientAuthMethod OBJECT-TYPE It is the authentication method the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.35 | AhAuthenticationMethod | read-only | current |
| ahClientEncryptionMethod OBJECT-TYPE It is the encryption method the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.36 | AhEncrytionMethod | read-only | current |
| ahClientMACProtocol OBJECT-TYPE It is the radio mode the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.37 | AhMACProtocol | read-only | current |
| ahClientVLAN OBJECT-TYPE It is the VLAN that the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.38 | Integer32 | read-only | current |
| ahClientUserProfId OBJECT-TYPE It is the user profile ID that the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.39 | Integer32 | read-only | current |
| ahClientChannel OBJECT-TYPE It is the radio channel that the client uses when communicating with the HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.2.40 | Integer32 | read-only | current |
| ahClientCWPUsed OBJECT-TYPE It is the Boolean datatype indicating whether a captive web portal is used. | 1.3.6.1.4.1.26928.1.1.1.1.2.41 | TruthValue | read-only | current |
| ahBSSID OBJECT-TYPE It is the basic service set identifier of the client if the ahRemoteId is a client. | 1.3.6.1.4.1.26928.1.1.1.1.2.42 | AhNodeID | read-only | current |
| ahPoEEth0MaxSpeed OBJECT-TYPE It is the automatically adjusted maximum Ethernet speed based on the power source and level. | 1.3.6.1.4.1.26928.1.1.1.1.2.43 | INTEGER {linkdown(1), eth10(2), eth100(3), eth1000(4)} | read-only | current |
| ahPoEEth1MaxSpeed OBJECT-TYPE It is the automatically adjusted maximum Ethernet speed based on the power source and level. | 1.3.6.1.4.1.26928.1.1.1.1.2.44 | INTEGER {linkdown(1), eth10(2), eth100(3), eth1000(4)} | read-only | current |
| ahPoEWifi0Setting OBJECT-TYPE It is the automatically adjusted Wi-Fi setting based on the power source and power level. | 1.3.6.1.4.1.26928.1.1.1.1.2.45 | INTEGER {invalid(0), linkdown(1), config(2), tx2rx3(3)} | read-only | current |
| ahPoEWifi1Setting OBJECT-TYPE It is the automatically adjusted Wi-Fi setting based on the power source and power level. | 1.3.6.1.4.1.26928.1.1.1.1.2.46 | INTEGER {invalid(0), linkdown(1), config(2), tx2rx3(3)} | read-only | current |
| ahPoEWifi2Setting OBJECT-TYPE It is the automatically adjusted Wi-Fi setting based on the power source and power level. | 1.3.6.1.4.1.26928.1.1.1.1.2.47 | INTEGER {invalid(0), linkdown(1), config(2), tx2rx3(3)} | read-only | current |
| ahAssociationTime OBJECT-TYPE The association time(s) of client connect or disconnect to AP. | 1.3.6.1.4.1.26928.1.1.1.1.2.48 | Counter32 | read-only | current |
| ahIDPInNet OBJECT-TYPE It is the Boolean datatype indicating whether AP is in local network. | 1.3.6.1.4.1.26928.1.1.1.1.2.49 | TruthValue | read-only | current |
| ahDiscoverAge OBJECT-TYPE It is the age from the rogue client is discovered. | 1.3.6.1.4.1.26928.1.1.1.1.2.50 | Counter32 | read-only | current |
| ahUpdateAge OBJECT-TYPE It is the age from the rogue client is updated. | 1.3.6.1.4.1.26928.1.1.1.1.2.51 | Counter32 | read-only | current |
| ahRunningAverageInterference OBJECT-TYPE channel utilizations running average interference. | 1.3.6.1.4.1.26928.1.1.1.1.2.52 | INTEGER | read-only | current |
| ahShortTermInterference OBJECT-TYPE channel utilizations short term interference. The short term period is defined by CLI config, usually, it should be in the range of 5 minutes to 30 minutes. | 1.3.6.1.4.1.26928.1.1.1.1.2.53 | INTEGER | read-only | current |
| ahSnapshotInterference OBJECT-TYPE channel utilizations snapshot interference. it is the last minute s means average. | 1.3.6.1.4.1.26928.1.1.1.1.2.54 | INTEGER | read-only | current |
| ahFailureSet OBJECT-TYPE It is the Boolean datatype indicating whether this failure(alert) is on or off. | 1.3.6.1.4.1.26928.1.1.1.1.2.55 | TruthValue | read-only | current |
| ahInterferenceThreshold OBJECT-TYPE the configured channel utilizations interference threshold. it is defined by CLI config. | 1.3.6.1.4.1.26928.1.1.1.1.2.56 | INTEGER | read-only | current |
| ahCRCErrRateThreshold OBJECT-TYPE the configured CRC error rate threshold. it is defined by CLI config. | 1.3.6.1.4.1.26928.1.1.1.1.2.57 | INTEGER | read-only | current |
| ahCRCErrRate OBJECT-TYPE short term CRC error rate. The interval of the refresh of CRC error rate calculation is the same interval as channel utilization short term means average interval. | 1.3.6.1.4.1.26928.1.1.1.1.2.58 | INTEGER | read-only | current |
| ahBandwidthSentinelStatus OBJECT-TYPE Bandwidth sentinel status. In alert message, the value should be zero. In clear message, the value should be 1. | 1.3.6.1.4.1.26928.1.1.1.1.2.59 | INTEGER {alert(0), clear(1), bad(2)} | read-only | current |
| ahGuaranteedBandwidth OBJECT-TYPE the configured guaranteed bandwidth(Kbps). it is defined by CLI config. | 1.3.6.1.4.1.26928.1.1.1.1.2.60 | INTEGER | read-only | current |
| ahActualBandwidth OBJECT-TYPE the actual bandwidth(Kbps). | 1.3.6.1.4.1.26928.1.1.1.1.2.61 | INTEGER | read-only | current |
| ahBandwidthSentinelAction OBJECT-TYPE bit maps to indicate which action has been taken on this client. bit 0: indicate whether log the guaranteed bandwidth violation or not, bit 1: indicate whether add more token to meet the minimum guaranteed bandwidth or not. | 1.3.6.1.4.1.26928.1.1.1.1.2.62 | Counter32 | read-only | current |
| ahBeaconInterval OBJECT-TYPE It is the number of time units between Beacon transmissions, One time unit is 1024 microseconds. | 1.3.6.1.4.1.26928.1.1.1.1.2.63 | Counter32 | read-only | current |
| ahLevel OBJECT-TYPE The level value will tell HM whether this is an interface level alert or a client alert. | 1.3.6.1.4.1.26928.1.1.1.1.2.64 | INTEGER {interface(1), client(2)} | read-only | current |
| ahAlarmAlertType OBJECT-TYPE There are five types, CRC Rate only applies to interface level alert, TX drop/retry rate is is calculated based on retries over total unicast TX frames, RX drop rate is calculated based on the dropped RX frames over total RX frames, Airtime percentage is the sum of both TX and RX airtime percentages. | 1.3.6.1.4.1.26928.1.1.1.1.2.65 | INTEGER {crcrate(0), txdroprate(1), txretryrate(2), rxdroprate(3), airtime(4)} | read-only | current |
| ahThresholdValue OBJECT-TYPE the configured CRC error rate, TX drop/retry rate, RX drop rate threshold. it is defined by CLI config. | 1.3.6.1.4.1.26928.1.1.1.1.2.66 | INTEGER | read-only | current |
| ahShortTermValue OBJECT-TYPE the percentage of this sampling period, CRC error rate, TX drop/retry rate, RX drop rate. | 1.3.6.1.4.1.26928.1.1.1.1.2.67 | INTEGER | read-only | current |
| ahSnapshotValue OBJECT-TYPE the snapshot value of CRC error rate, TX drop/retry rate, RX drop rate. | 1.3.6.1.4.1.26928.1.1.1.1.2.68 | INTEGER | read-only | current |
| ahIfName OBJECT-TYPE Name - uniquely identifies an AP Interface. | 1.3.6.1.4.1.26928.1.1.1.1.2.69 | AhString | read-only | current |
Notifications
| Name | OID | Status |
|---|---|---|
| ahFailureTrap NOTIFICATION-TYPE This event is generated for any equipment or software failures. | 1.3.6.1.4.1.26928.1.1.1.1.1.1 | current |
| ahThresholdCrossingEvent NOTIFICATION-TYPE This event is generated whenever a threshold is crossed for the first time. | 1.3.6.1.4.1.26928.1.1.1.1.1.2 | current |
| ahStateChangeEvent NOTIFICATION-TYPE This event is generated whenever an object state change occurs. | 1.3.6.1.4.1.26928.1.1.1.1.1.3 | current |
| ahConnectionChangeEvent NOTIFICATION-TYPE This event is generated whenever a connection state change occurs. The connection might be between a HiveAP and its client, or between a HiveAP and a neighboring HiveAP. | 1.3.6.1.4.1.26928.1.1.1.1.1.4 | current |
| ahIDPStationEvent NOTIFICATION-TYPE This event is generated whenever IDP detects an AP in its neighborhood. The ahRomoteId indicates the detected AP MAC address, and the ahIDPCompliance indicates conformance of IDP policy this AP satisfies. The ahIDPChannel and ahIDPRSSI indicates the radio channel and Receive Signal Strenth Indication. | 1.3.6.1.4.1.26928.1.1.1.1.1.5 | current |
| ahClientInfoEvent NOTIFICATION-TYPE This event is generated whenever HiveAP a new client makes an association and its IP address, hostname, and User name is obtained. | 1.3.6.1.4.1.26928.1.1.1.1.1.6 | current |
| ahPoEEvent NOTIFICATION-TYPE This event is generated whenever a HiveAP (802.11n product line) boots up or changes power levels. | 1.3.6.1.4.1.26928.1.1.1.1.1.7 | current |
| ahChannelPowerChangeEvent NOTIFICATION-TYPE This event is generated whenever a HiveAP boots up, or changes channels or power levels. | 1.3.6.1.4.1.26928.1.1.1.1.1.8 | current |
| ahIDPMitigateEvent NOTIFICATION-TYPE This event is generated whenever IDP detects an rogue client connect to a rogue AP. The ahRomoteId indicates the detected Station MAC address. | 1.3.6.1.4.1.26928.1.1.1.1.1.9 | current |
| ahInterferenceMapAlertEvent NOTIFICATION-TYPE For every one minute interval, AP will monitor the interference channel utilizations (snapshot, short term means average and running average) and CRC error rate against their thresholds, if any one of them is above their threshold (thresholds are settable by CLI), AP should send HM an interference alert event to HM. AP will send out clear alert to HM only when: the last short term period s CRC-error-rate, means average Interference CU and the last snapshot interference CU are all below their thresholds. | 1.3.6.1.4.1.26928.1.1.1.1.1.10 | current |
| ahBandwidthSentinelEvent NOTIFICATION-TYPE HiveOS will send two different kinds of traps: bandwidth sentinel alert trap, and bandwidth sentinel clear trap. The alert trap will serve the purpose to tell HM that the client is violating the bandwidth sentinel, the clear trap will clear the previous alert trap. | 1.3.6.1.4.1.26928.1.1.1.1.1.11 | current |
| ahAlarmMsgMapAlertEvent NOTIFICATION-TYPE HiveOS will send two different kinds of level alert: interface level alert, and client level alert. There are four alert types, CRC error rate, TX drop/retry rate, Rx drop rate; interface level includes all alert type, the client level includes Tx drop/retry rate, Rx drop Rate; the 'set' alert means there is an alert raised, with type indicated in the alert type field, the 'clear' alert means the previous alert condition has been cleared. | 1.3.6.1.4.1.26928.1.1.1.1.1.12 | current |